SPECIAL REPAIRS TO BLDG NO T-82 (A COY OR LINE) AND BLDG NO T-72 (URO COMPLEX) OF ASC BN (MT) UNDER GE (EAST) MATHURA

Amount

Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings including ridges, hips, valleys etc complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based semi corrugated steel sheet 0.50mm thick of red colour (AZ-150) having tensile strength of 550 Mpa in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to walls, ridges/valley gutters, fixed with self tapping screws complete all as specified and as directed.

Dismantling timber scantlings (framed work) exc 40 Sq cm in section in any position complete all as specified and as directed.

S&F rolled mild steel joist, channel, angle or Tee section for framed work as in trusses, purlin, vertical posts including special shaped washer, angle cleats, fish plates, gusset plates, base/ bearing plates, bolts and nuts etc confirming E-250 quality 'A' complete all as specified and as directed.

S&F MS flat iron wind ties for roof including all necessary drilling, bolting or riveting etc conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation, etc) or insulation board/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed .

M&L for providing and fixing inter locking metal grid (snap grid for false ceiling) of size 605 mm x 605 mm in true horizontal level, hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24 mm X 38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200 mm x 600 mm and secondary cross “T” of length 600 mm and size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200 mm X 600 mm panel to form grids of 600 mm X 600 mm and wall angle of size 24 mm X 24 mm X 0.4 mm. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 mm X 37 mm X 25 mm X 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 mm X 30 mm X 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint for all hights complete all as specified and as directed.

M&L for 4 mm thick non-asbestos fibre cement building board having fire resistance & moisture resistance properties and fixed in ceiling complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in bed blocks, coping, benching, roof kerbs chamfered on edges including throating slightly complete all as directed and as specified.

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and as directed.

M&L for Brick work with fly ash Bricks straight or curved on plan to any radius as in half built thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L for Brick work using old size fly ash Bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

Taking down cement plaster on brick walls and concrete surface including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

M&L for rendering 15 mm thick on other than fair faces of brick wall or concrete surface in cement mortar 1:4 mixed with liquid water proofing compound as per manufactures instructions surface finished even & fair complete all as specified and as directed. Note : Liquid WPC shall be measured and paid seperately under relevant item of this BOQ.

Supply only liquid water proofing compound complete all as specified and as directed.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even & fair complete all as specified and as directed.

M&L for providing damp proof layer in two coats of acrylic polymer coating consisting of 1 part of acrylic polymer liquid mixed with 2 parts of cementious powder applying at the rate of 1.40 Sqm/Kg of mix per coat. Second coat should be applied after 4-6 hrs of first coat, 5 days curing is to be carried out to the surface before providing plastering complete all as specified and as directed. Note : Make of the material 'Smart Care damp block 2K' of Asian paints or equivalent from Dr Fixit, STP, CICA etc. as approved by GE

M&L of preperation of newly plastered surfaces of walls and applying two coats of oil bound distember over and including a coat of alkali resistant primer using spray machine, spray hard to receive area to achieve excellent application using limited manpower complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint white or tinted over and including a coat of primer complete all as specified and as directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) area exc 1.5 Sqm but n exc 4.00 Sqm each complete all as specified and as directed.

S&F Pressed steel frames of size 125x60 mm made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete as specified and as directed.

M&L for cement concrete 1:3:6 type C-0 (using 12.5 mm graded stone aggregate) as in bed blocks for fixing hold fasts and filling of pressed steel frame complete all as specified and as directed.

S&F 35 mm thick flush shutters, solid core construction with block board core and plywood face panel commercial type on both sides complete all as specified and as directed.

S&F 35 mm thick second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and as directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts 250 mm long of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F aluminium anodized barrel tower bolts 200 mm length of bolt of extruded section and fixed complete all as specified and as directed.

S&F extruded aluminium handles of size 150mm, cast type, anodised complete all as specified and as directed.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete as specified and as directed.

S&F 150mm, mild Steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamal paint over and including a coat of red oxide primer complete as specified and as directed.

M&L for prepration of new wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer complete all as specified and as directed.

S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed..

S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded ccomplete all as specified and as directed..

S&F 4mm thick, Sheet glass ordinary quality and glazing with rubber beading in square n exc 0.5 sqm in each pane complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (Below or above ground level) complete all as specified and as directed.

M&L for 100 mm thick cement concrete 1:4:8 type D2 (using 40 mm graded aggregate) as in sub floors, sub bases, floors and paving etc. complete all as specified and as directed.

M&L for 80mm factory made chamferred edge precast concrete interlocking paver blocks any shape and size locally available of best quality and confirming to IS 15658-2006, M-30 grade with grey cement and pigments with approved colour design & pattern as in footpath, parks, lawn, or light traffic ways of required strength made by table vibratory method using PU mould laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, compacted and proper embedding/laying of interlocking paver block into the sand bedding layer through vibratory compaction by using plate vibrator filling the joints with fine sand and cutting of paver block as per required size and pattern finishing and sweeping extra sand complete grey cement and pigments complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, apron etc laid bedded and pointed in any mortar complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20-22 mm thick laid over and including 15mm thick screed bed in cement mortar 1:4 and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L Machine cut kota stone slab flooring 18-20mm thick as in skirting, dado and pillar etc laid over and including 10mm thick rendering in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

M&L for 50 mm thick cement concret type C-1 1:3:6 (using 20 mm graded stone aggregate) as in plinth protection, finishing cement concrete surface even and smooth (without using extra cement) and filling the joints with bitumen and sand mixed in ratio of 1:2 by weight complete all as specified and as directed.

M&L for framed work such as grills, gratings, etc. with ends of bars shouldered or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand, gaurd bar, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

M&L for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamal paint complete as specified and as directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors) beams, staircases, landing, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition) including removal of debris outside of premises complete all as specified and as directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) area not exc 1.5 Sqm each complete all as specified and as directed.

S&F Pressed steel frames of size 105x60 mm made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete as specified and as directed.

S&F Floor door stopper of aluminium alloy body with 2 legs runner shoes with hard drawn steel spring hard overall length of cover plate 150mm complete all as specified and as directed.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete as specified and as directed.

M&L for hardcore of broken stone or boulder gauge n exc 63mm, deposited, spread and levelled in layers n exc 15cm thick watered and rammed to true surface complete all as specified and as directed.

M&L plain cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in base of flooring/hardstanding complete all as specified and as directed.

M&L for forming 30mm x 10mm thick construction joints filled with sealing compound, Grade ‘A’ complete all as specified and as directed.

M&L for cement concrete 1:4:8 type D2 (using 40 mm graded aggregate) as in foundations filling and mass concrete complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of concrete surface as on ceiling in cement mortar 1:3 finished even & fair complete all as specified and as directed.

M&L for preparation of new plastered surface of ceilling and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of new plastered surface of wall and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of old painted steel and iron surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamal paint complete as specified and as directed.

M&L for 50mm thick sand stone slab as in chajja/cover slab set and jointed over supports in cement mortar 1:4 complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and as directed.

S&F steel rolling shutters, thickness of laths 1.00mm with ball bearing gear operated type with bevel gear box and crank handle and safety lever locks mild steel with 4 levers for rolling shutters as as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, complete push pull or manual type complete all as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm as in soft/loose soil complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundations filling and mass concrete complete all as specified and as directed.

M&L 75mm thick cement concrete 1:4:8 type D2 (using 40 mm graded aggregate) as in sub floors, sub bases, floors and paving etc. complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning for refixing or removed to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

S&F PVC (SWR) 110 mm bore pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

Taking down carefully aluminum/copper point wiring (light ,fan, socket any type, power, bell etc.) complete including fixtures & fittings (such as ceiling rose, socket, Pendent, regulator, etc) and removing the material from site and making good the disturbed surfaces of walls ceiling etc complete all as specified and as directed.

Taking down carefully by Submain wiring of any type size and make making good the disturbed surface to match with existing surface complete all as specified and as directed.

Taking down old unserviceable existing SPN/TPN DB/enclousers any size and type/any descriptions as iron sheet scrap excluding MCB any type/size and making good disturbed surface/wall as per existing complete all as specified and directed.

M & L for Point wiring with 1.5 Sqmm (nominal area) single core PVC insulated unsheathed (FRLS) cable, multi-stranded, copper conductor, in universal colour code with & including suitable size of rigid non-metallic PVC conduit (not less then 20mm dia medium grade) and its all accessories complete concealed in wall incl cutting & chases(making good all to the disturbed surfaces as per existing) including modular flush metal boxes with cover plate and frame for mounting modular switches, sockets, regulators etc or including sunk cast iron/pressed steel/terminal boxes for mounting flush type switchs/sockets etc with 3 mm thick phenolic laminated sheet covers including earth wire of PVC insulated (FRLS) copper conductor multistranded of 1.5 Sqmm size in green colour complete all as specified and as directed for the followings:-

One light/ fan point controlled by one way switch 5 amp complete all as specified and as directed.

One 3 pin 5 Amps socket point controlled by one way switch on same board complete all as specified and as directed.

One 3 pin 5 Amps socket point controlled by one way switch on independent board complete all as specified and as directed.

All as per item No. 71.00 here-in-above but for 3pin/5pin 16Amps socket point controlled independently, with 4 Sqmm PVC insulated & unsheathed (FRLS) copper conductor cable independent Point wiring complete all as specified and as directed.

S&F ceiling rose surface bakelite 65mm x 50mm three terminals complete all as specified and as directed.

S&F switch piano type , SP, one way, flush type 5 Amps complete all as specified and as directed.

S&F switch piano type , SP, one way, flush type 15 Amps complete all as specified and as directed.

S&F socket out let 2 in 1 flush type 3 pin 5 Amp complete all as specified and as directed.

S&F socket out let 2 in 1 flush type 3 pin 15 Amp complete all as specified and as directed.

S&F step type electronic fan Regulator flush type, 2 Module complete all as specified and as directed.

S&F indoor wall mounted fitting, brushed nickel finish fixture with opal glass diffuser, with LED retrofit bulb B-22 of capacity 09 watts complete all as specified and as directed.

S&F indoor decorative ultra slim surface/Wall mounted LED batten tube light fitting with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K, >100 Lm/Watt complete with all accessories internally pre-wired with and including 1 x 20 watt LED tube and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F LED Building security light fitting 30W with lens & driver, powder coated pressure die cast aluminium, top opening and maintainable with heat resistance toughened glass, built-in Short-Circuit Protection, Over voltage Protection and Surge Protection, IP-65 proction with luminaire efficiecy of greater than 80Lumen/Watt, Colour rendering (CRI) of ≥ 70 and co- related colour temperature (CCT) of 5700K (±500K) . The luminaire should have 10 KV surg protection, PF ≥ 0.9 and total harmonic distortion of THD ≤ 10%, voltage range of 140-280V with and including 30W LED tube all connections complete all as specified and as directed.

S&F building security light bracket made out of 40mm dia medium grade GI pipe of 1.2 m length bent to required shape suitable for fixing street light fitting on Steel tubular pole/walls including two Nos clamps made out 40mm X 6mm flat with suitable nuts and bolts including applying two coats of aluminium paint over a coating of red oxide primer complete all as specified and as directed.

S&F sheet metal enclosure MCB distribution board, SPN 12 Way, Double door, phosphatised, powder coated with 200Amp rated bus-bar, neutral link, earth bar and din rail , cable ties for cable management, 240 V complete all as specified and as directed.

S&F TP&N Vertical Loadline distribution board, 4 Way, Double door, sheet steel, phosphatised, powder coated with Copper bus-bar 200Amp, neutral link, earth bar and din rail ,blanking Plates, cable ties for cable management, 440 V, complete all as specified including fitting suitable for MCBs with connection complete all as specified and as directed Note : - (i) DB shall be fixed in flush pattern by cutting the wall and making good disturbed surface as directed.

Supply & fix in replacement of MCCB 4 pole, 415V adjustable type 125 Amps, breaking capacity 16KA complete all as specified and as directed.

S&F MCB SPN 63 Amps,' C' series, breacking capacity 10KA, 240V complete all as specified and as directed.

S&F MCB SP 6-32 Amps,' C' series, breacking capacity 10KA, 240V complete all as specified and as directed.

S&F MCB SP 40-63 Amps, 'C' series, breacking capacity 10KA, 240V complete all as specified and as directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades and deposite to AGE E/M (East) store complete all as specified and as directed.

Hanging only ceiling fan after replacement of suitable length down rod with hook and rubber seat, nut bolt complete and connecting up including provision of 1.5 sqmm PVC insulated and PVC sheathed wire from ceiling rose to fan complete all as specified and as directed.

M&L for Sub Main Wiring with two runs single core 10sqmm PVC insulated unsheathed (FRLS) cable with multistranded, 1100 volts grade copper conductor drawn in suitable size of rigid non-metallic PVC conduit (not less then 25mm dia med gd) and its all accessories complete concealed in wall/roof incl cutting & chases (making good all to the disturbed surfaces as per existing) with and including 10sqmm copper green colour earth wire complete all as specified and as directed. Note : Two runs 10sqmm, one run of 10sqmm earth wire & One run of PVC conduit shall be measured as one unit length.

M&L for Sub Main Wiring with four runs single core 10sqmm PVC insulated unsheathed (FRLS) cable with multistranded, 1100 volts grade copper conductor drawn in suitable size of rigid non-metallic PVC conduit (not less then 25mm dia med gd) and its all accessories complete concealed in wall/roof incl cutting & chases (making good all to the disturbed surfaces as per existing) with and including 10sqmm copper green colour earth wire complete all as specified and as directed. Note : Four runs 10sqmm, one run of 10sqmm earth wire & One run of PVC conduit shall be measured as one unit length.

Supply and Fixing Modular switch,single pole, one way 6 Amps, combined 1 Module complete all as specified and as directed.

Supply and Fixing Modular switch,single pole, one way 16 Amps, combined 1 Module complete all as specified and as directed.

Supply and Fixing electronic step type Modular fan regulator 2 Module complete all as specified and as directed.

Supply and Fixing Modular socket 2-in-1, 5 pins 6 Amps , combined 2 Module complete all as specified and as directed.

Supply and Fixing Modular socket 2-in-1,3 and 5 pins 6 /16 Amps, combined 2 Module complete all as specified and as directed.

S&F lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

S&F LED 9 W suitable for normal holder (Base Cap E22) warm white/cold white/natural white complete all as specified and as directed.

Taking down the ceiling fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearings, reassembling the fan and blades, painting of fans with synthetic enamel paint by spraying a single coat as per existing colour paint including filling cavities with filler, writing MES No. in paint, hanging/fixing the fan in its original position and testing on completion complete all as specified and as directed. Note:- The spare parts (such as bearing, capacitor, rubber wheel push, fan winding etc) required shall be measured and paid separately under relevant items as supply only.

Dismantling the unserviceable ball bearing and supply and fix ball bearing suitable for ceiling fan/exhaust fan complete all as specified and as directed.

Material & labour for removing the defective fan winding of ceiling fan size upto 1200mm/1400 mm sweep and rewinding with super enamelled copper wire of existing gauge, applying insulation varnish, soldering, pre heating and binding with empire tubes, crimple sheet etc. as required for rewinding complete all as specified and as directed.

S&F industrial plug and socket enclosure 3 phase type, controlled with TPN MCB 63 Amps, 415 Volt complete all as specified and as directed.

S&F air circulators fans 230 volts single phase oscillating 600mm sweep suitable for wall mounting complete with all accessories fixing on wall complete all as specified and as directed.

S&F LED 80W highbay light fitting with aluminium PDC housing and toughened glass integrated driver, built-in Short-Circuit Protection, Over voltage Protection and Surge Protection, high luminous effeciency upto >100 lm/W, IP-65 protection, suitable for ceiling mount (surface/suspended) including all connections and fixtures complete all as specified and as directed.

S&F MCB SPN 40-63 Amps, 'C' series, breacking capacity 10KA, 240V complete all as specified and as directed.

M&L for Cutting holes/modified holes for air ducting of exhaust fan in Circule/square shape or as per site requirement into or through concrete walls built in cement mortar of superficial area exc 400 sq.cm but n.exc 0.10 sq.m to a depth of 30cm including making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) and cover hole as required and rubbish off the premises complete all as specified and as directed.

S&F exhaust fan 250mm sweep sturdy engineer plastic body complete with louvers, AC 230 Volt single phase 50 Hz supply and including connecting up with twin core twisted flexible copper conductor cable of suitable size 0.75 Sqmm complete all as specified and as directed.

Material and labour for Earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4.0 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and chaarcoal filling, necessary excavation and earth work complete.

B S ENTERPRISES (BID ID -3142846)

Ahmed constructions (BID ID -3141691)

JWALA ELECTRIC CONTRACTORS (BID ID -3142243)

M/S ANIL KUMAR (BID ID -3141182)

M/s Orient Traders (BID ID -3143347)

Deepak Saxena (BID ID -3143098)

BHARDWAJ CONSTRUCTIONS (BID ID -3140917)