GE ELECT/D-55/2025-26

Amount

Taking down over head conductor from existing PCC street light pole safely after disconnecting properly from existing serviceable street light including T&P , hydra , man power complete all as specified and directed by Engr-in-Charge.

Taking down insulator from existing PCC street light pole safely after disconnecting properly from existing serviceable street light including T&P, hydra, man power complete all as specified and directed by Engr-in-Charge.

Taking down /dismantling cross-arms of M.S. channel from existing PCC street light pole safely after disconnecting properly from existing serviceable street light including T&P , hydra , man power complete all as specified and directed by Engr-in-Charge.

Labour & T&P only for trimming of tree branches all around the street light tubular pole with the help of ladder and after removing disposed Off the same away from resident area complete all as specified and directed by Engr-in-Charge.

S&F in replacement of unsv driver accessories suitable for existing LED secruity/ flood light/ High mast of suitable size specification as per site requirement complete all as specified and directed by Engr-in-Charge.

Taking out old unserviceable street light fittings and supply and fixing of new generation energy saving and environment friendly long life verasalite pressure die- cast aluminium IP 65 road way luminare with high power LEDs of 90 Watts capacity as light source and exclusively designed for poly carbonate cover with electronic drive.along with necessary wiring and clamps for fixing on complete all as specified and directed by Engr-in-Charge.

M & L for cutting and removing grass, vegetation bushes etc from surrounding of installation/LT Panel/Sub Stations and removing all rubbish to a distance not exceeding 50 m complete all as specified and directed by Engr-in-Charge.

Material and labour for PCC 1:4:8 type D-2, (using 40 mm graded crushed stone aggregate) for foundation, filling and mass concret etc complete all as specified and directed by Engr-in-Charge.

Material and labour for PCC 1:3:6 type C-2, (using 40 mm graded crushed stone aggregate) for foundation, filling and mass concret etc complete all as specified and directed by Engr-in-Charge.

Material and labour for PCC 1:2:4 type B-1, (using 20 mm graded crushed stone aggregate) for Coping etc complete all as specified and directed by Engr-in-Charge.

M&L for re-painting of LT Steel tubular poles of any sizes with apply of 2 coats of aluminium paint including rubbing with wire brush/emery paper & writing pole Nos in appropriate size of letters including making yellow and black radium strips upto height of 1.5 mtr above from ground level complete all as specified and directed by Engr-in-Charge.

Supply & fixing in replacement of SMC Junction box for street light having side hinged, outside dimention 333x233x120mm and inside dimention 300x200x105mm including 4 Nos aluminium bus bar of 40 Amps rating and 1 No 5 A MCB SP connecting of existing LT power cable complete all as specified and directed by Engr-in-Charge.

S&F in replacement of contactor 3 Pole power contractor, type MNX 110, 415 volt having 2 NO +2 NC contacts complete all as specified and directed by Engr-in-Charge.

S&F in replacement of contactor 3 Pole power contractor, type MNX 40, 415 volt having 2 NO +2 NC contacts complete all as specified and directed by Engr-in-Charge.

S&F in replacement of MCB 3 pole , 32 Amps,50 Hz,415 Volts, 16 KA, with thermal magnetic release complete all as specified and directed by Engr-in-Charge.

S&F in replacement of Analog Time switch , 240 Volt AC , 50 Hz complete all as specified and directed by Engr-in-Charge.

S&F in replacement of Digital Time switch , 240 Volt AC , 50 Hz complete all as specified and directed by Engr-in-Charge.

Taking out old damage LT pole and Supplying, Errection & Fixing Steel Tubular swan neck pole SP-31 ,(09 metres long) Painting of Poles with one coat of red oxide primer and one coat of aluminum paint before fixing and one coat of aluminum paint after fixing. The complete embedded portion shall be painted with two coats of black bituminus paint complete with cast iron base plate complete all as specified and directed by Engr-in-Charge. (Note : Excavation earth work ,PCC may be paid separatly of respective items.)

Supply, Laying, connecting, testing and commissioning in replacement of size 3.5 core, 50 sqmm ( including taking out existing cable) LT cable of PVC sheathed XLPE cable armoured aluminium conductor 1100 V graded after taking out/down old existing unserviceable from trenches / ducts/ road crossing/wall and poles complete all as specified and directed by Engr-in-Charge.

All as per srl item No 19 here-in-before but size of 3.5 core, 35 sqmm complete all as specified and directed by Engr-in-Charge.

All as per srl item No 19 here-in-before but size of 3.5 core, 25 sqmm complete all as specified and directed by Engr-in-Charge.

All as per srl item No 19 here-in-before but size of 4 core, 16 sqmm complete all as specified and directed by Engr-in-Charge.

All as per srl item No 19 here-in-before but size of 4 core, 10 sqmm complete all as specified and directed by Engr-in-Charge.

Material & labour for excavation in trenches in soft and loose soil n.exc 1.5 mtr wide and n.exc. 1.5 mtr depth for laying and taking out of electric power cable and getting out complete all as specified and directed by Engr-in-Charge.

Material & labour for returning filling in including spreading leveling watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed by Engr-in-Charge.

Material & labour for removing excavated material not exceeding 50 mtr away and depositing where directed at a level n. exc 1.5 mtr above the starting point complete all as specified and directed by Engr-in-Charge.

Material & labour for river washed and screened dry sand for filling under and above the under ground cable for cushioning of cables etc complete all as specified and directed by Engr-in-Charge. Note : Measurement shall be taken after punning down.

Laying only old unreinforced precast concrete cable covers class LV type -1 flat, size 250 x 150 x 40 mm complete all as specified and directed by Engr-in-Charge.

Supply and laying of unreinforced precast concrete cable covers class LV type -1 flat , size 250 x 150 x 40 mm. complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of new generation energy saving & enviroment friendly aluminium pressure die cast high power LED flood light luminare of wattage 120 Watts of IP66, class I portection integral driver operation at 170-270VAC 50Hz supply complete all as specified and directed by Engr-in-Charge.

Material & labour in replacement for service cable 6 Sqmm 2 core 1100 volts grade heavy duty cable PVC insulated stranded alumn conductor, served with an inner sheathing of PVC tape and overall PVC sheathed in service connections/perimeter light supply as per site requirement, flat or circular complete all as specified and directed by Engr-in-Charge.

Material & labour for boring of holes under road/pavement/hard standing including material and labour including HDPE pipe of 80mm dia suitable for 04 Kg/cm working pressure. Wall thickness of pipe not less than 6.5 mm complete all as specified and directed by Engr-in-Charge.

Taking down carefully from poles defective street/flood light fitting of any size for repairs and refixing the same after replacing defective accessories like driver, & PVC insulated sheathed copper conductor etc complete & testing to entire satisfaction of Engr-in-Charge. (Note : - (i) Accessories like driver suitable for LED light of specified size & PVC copper wire of different size shall be measured and paid separately (ii) Quoted rate deemed to be included all Machinery, ladder, Tools & Plants needed for the necessary repair work of street/flood light.

M&L in replacement for cable with copper conductor PVC round sheathed(flexible) of size 1.5 Sqmm 2 core for connecting the same complete all as specified and directed by Engr-in-Charge.

Material and labour for PCC 1:2:4 type B-1, (using 20 mm graded crushed stone aggregate) for Coping (Size: LxWxH-0.45Mx0.45Mx0.45M) etc complete all as specified and directed by Engr-in-Charge.

Taking out old post lamp lantern light fitting and supply and fixing of new generation energy saving and environment friendly long life verasalite pressure LEDs of 70 Watts capacity as light source and exclusively designed for poly carbonate cover with electronic drive complete all Accessories complete all as specified and directed by Engr-in-Charge.

M&L for disconnecting all electric LT Supply from timer panel of 15 mtr height High mast and lowering down the high mast light fitting set by using motor/manually for repair/replacement work and change the unsv/worn out parts after repair works completed check the serviceability of high mast and remove all dust/nest and greasing the rope/motor/gear assembly for proper functioning before raising up in the the original position complete all as specified and directed by Engr-in-Charge. Note: Quoted rate shall deemed to be included all Hydra Lifting Machinery vehicle ,Tools & Plants needed for the necessary repair work of Himast light.

Supply only stainless steel rope 6mm dia complete all as specified and directed by Engineer-in-charge

Supply only D clamp including nut bolt and washers complete all as specified and directed by Engineer-in-charge

Supply only 6 Sqmm 5 Core flexible copper cable complete all as specified and directed by Engineer-in-charge

Supply only 1.5 HP motor 3 Ph 440 volt 50 hz AC supply for operating the stainless steel rope through gear assembly complete all as specified and directed by Engineer-in-charge

Supply only gear assembly used for operating the stainless rope for lowering down the high mast fitting complete all as specified and directed by Engineer-in-charge

Supply and fixing in replacement Energy saving, environmental friendly, long life, exclusive innovative die-cast aluminum IP66 LED flood light suitable for high lighting architectural façade and general purpose lighting of capacity 200/210 Watt LED complete all as specified and directed by Engr-in-Charge.

M&L in replacment of Earthing complete with galvanized steel earth plate electrode of size 60cmx60cmx6 mm thick, buried directly in ground (earth pit not less than 2.10 m below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level, connected to galvanized earth lead wire of dia 4 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel as shown in electrical plate No 3 of SSR Part I, connected to earth test point and the equipment on the other nuts and washers of galvanised ironside complete all as specified, including testing and commissioning complete all as specified and directed by Engr-in-Charge. Note : (a) The unit rates quoted against this item shall be deemed to include the cost of excavation and earth work in any type of soil, common salt & charcoal dust in alternate layers, PCC 1:3:6 as in pit, precast RCC 1:2:4 type B-1 with necessary reinforcement as in cover & frame for pit, funnel, watering pipe 20 mm bore GI pipe light grade, protection pipe GI pipe medium grade etc. (b) The quoted rates shall also deemed to include the cost of earth test point and earth wire and protection pipe upto 7.5 meter beyond the earth plates electrode.

Laying/undergrounding connecting, testing and commissioning only existing LT XLPE cable of PVC sheathed XLPE cable armoured aluminium conductor 1100 V graded including excavation, earth wk, returning filling etc complete all as specified and directed of size10 Sqmm to 95 Sqmm complete all as specified and directed by Engr-in-Charge.

M&L for applying alternate 30 cm depth paint upto height of 1.5 mtr of different colours on PCC poles as above from ground level complete all as specified and directed by Engineer-in-Charge

S & F in replacement RMU battery 12V, DC, 7 AH maintnance free dry battery complete all as specified and directed by Engr-in-Charge.

Opening of the VCB , 11 KV 400 to 800 Amps of any make by removing of the Breaker from the existing position after disconnecting all the connections from the system, servicing, Overhauling of the same, checking of the same for proper operation, spring charge, charged control cables are fastened tightly to the terminals, any abnormality, VCB, cleaning the surface of the insulators, fasten the bolts, checking and correcting interrupting units, mechanism, linkages etc, fasten the hardwares of control wiring, check that the split pins, Circlips, dowell pins etc. have not come out and are intact, lubricate the mechanism, moving parts by castrol, all purpose grease or equivalent, check that the vaccum pots/chambers is within limit including opening of the shutters properly, replacing of the trip catch, roller, holding catch, stopper, close push button, closing cum reassembling, controll limit switches reconnecting of the breaker for smooth functioning complete all as specified and directed by Engr-in-Charge. (Note:- Spare parts will be paid separately under respective items)

Supply in replacement of space heaters of 100 KW, 220Volts complete all as specified and directed by Engr-in-Charge.

Supply in replacement of thermostate adjustable type 30 to 120 degree C complete all as specified and directed by Engr-in-Charge.

Supply in replacement of in replacement of motor & gear assembly 230V AC suitable for 400/630/800 amps, 11 KV HT VCB including testing & puting on load complete all as specified and directed by Engr-in-Charge.

Supply in replacement (at site on VCBs as per existing size), male contact (Copper) suitable for HT 11 KV power supply complete all as specified and directed by Engr-in-Charge.

Supply in replacement (at site on VCBs as per existing size), Female contact (Copper) suitable for HT 11 KV power supply complete all as specified and directed by Engr-in-Charge.

Supply in replacement of Current Transformers draw type 11kV, 300/150/1-1, Core1: Class 5P10, 10VA, Core2: Class 0.5, 10 VA complete all as specified and directed by Engr-in-Charge.

Supplying and fixing in replacement of Current Transformers draw type 11kV, 400/200/1-1, Core1: Class 5P10, 10VA, Core2: Class 0.5, 10 VA complete all as specified and directed by Engr-in-Charge.

Taking down the old/unserviceable potential transformer supply & fix new 11KV/110V/100VA with drawable type and epoxy incl PT grid with risers complete suitable for HT 11KV panel complete incl testing & commissioning complete all as specified and directed by Engr-in-Charge.

Shifting of Transformer from substations to variours substation /transformers locations in the area of AGE(U) E/S No III by road using and removing the faulty transformer by fxing/errecting of the healthy tansformer with the hydra/crane support making the necessary HT/LT cable connections earth connections and restoration of power supply complete all as specified and directed by Engr-in-Charge.

Taking down unserviceable sheet gasket (Cork sheet), Supply and fix synthetic rubberized cork sheet gasket 6mm 2' x 3' size sheet thick for top cover HT/LT bushes at places existing and tighting all the bushings and top cover to avoid any oil leakages of capacity 160 KVA to 630 KVA complete all as specified and directed by Engr-in-Charge.

M&L for replacement Earthing complete with galvanized steel earth plate electrode of size 60cmx60cmx6 mm thick, buried directly in ground (earth pit not less than 2.10 m below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level, connected to galvanized iron strip 32 x 6mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel as shown in electrical plate No 3 of SSR Part I, connected to earth test point and the equipment on the other nuts and washers of galvanised ironside complete all as specified, including testing and commissioning complete all as directed. Note : (a) The unit rates quoted against this item shall be deemed to include the cost of excavation and earth work in any type of soil, common salt & charcoal dust in alternate layers, PCC 1:3:6 as in pit, precast RCC 1:2:4 type B-1 with necessary reinforcement as in cover & frame for pit, funnel, watering pipe 20 mm bore GI pipe light grade, protection pipe 40 mm bore GI pipe medium grade etc. (b) The quoted rates shall also deemed to include the cost of earth test point and earth strip and protection pipe upto 7.5 meter beyond the earth plates electrode.

Material and labour for painting to the both sides of fencing of 11 KV out door sub station having transformer/RMU by scraping the existing surface and applying a coat of synthetic enamel paint of the existing colour and complete all as specified and directed by Engr-in-Charge.

Calibration of all the electromagneitic/ thermal/ microprocessor relays of 11 KV VCB/RMU and setting the relay tripping timings in advance to the feeding sub station to ensure pock wise re-installation of various relays in position with complete testing and commissioning. Ensure proper functioning complete all as specified and directed by Engr-in-Charge. Note :- (a). Primary & secondary injection kit shall be arranged by the contractor (b) DC Supply for relay testing shall arranged by the contractor (c) The contractor shall prepare the relay adjustment and tripping timing chart in the follow up fashion and submit to Engineer-in-Charge

Material and labour for complete bush cutting vegetation around the 11 KV substations/ transformers lines complete all as specified and directed by Engr-in-Charge.

Filtration/dehydration of 11 KV distrubution transformer oil through filtration plant to improve the dielectric strength/insulation valve of the transformer oil upto 60 KV at a gap of min 2.5 mm of electrodes. (a) The contractor will take shut down orders in working before commencement of the work (b) The contractor shall ensure no wastage at transformer oil (c) The Contractor is solely responsible for any damage to the transformer during filtration operations. He is responsible for making good any damage to the transformer at his own cost without any extra cost to the department. (d) The contractor shall ensure that the conservator tanks are full to its level before starting the dehydration. Note : Oil for Top up will be measure and paid seperatly under respective items. (e) the di-electric strenght of oil shall be tested before & after filtration. Test results shall be submitted to engineer-in-charge

Material and labour for preparation of old painted surfaces of floor mounted indoor/outdoor type transformer from 100 KVA to 500 KVA capacity by cleaning/rubbing with course cloth wire brushes to remove dust deposits oil grease and repainting by applying one coat of spray paint with synthetic enamel paint of approved colour without disturbing/damaging the electrical net work system/equipment including making of capacity /rating /incoming outgoing details in capital english alphabet of size complete all as specified and directed by Engr-in-Charge.

All as per item No 65 above but from 630 KVA to 1000KVA complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of silica gel breather assembly complete with breather unit and silica gel including connecting with proper rubberised gasket and necessary fittings GI fittings for fixing/assembling upto 1000KVA transformer complete by removing the unserviceable silica gel breather assembly complete all as specified and directed by Engr-in-Charge. Make : Patel Electrical Industries or equivalent recommende by OEM

Supply, filling and for topping up the transformer with new transformer oil duly filtered with filtration plant. Note : (a) The transformer oil shall be type EHV confirming to IS - 335(2018) (b) Mineral oil grade shall be used. (c) The transformer oil should have a high dielectric strength not less than 60 KV at a gap of min 2.5 mm of electrodes.

Taking down burnt defective drawnout/inlet Valve (Brass any size) and supply and fixing new drawn out/Inlet valve (brass as per existing size) suitable for any make of 100 to 500KVA Transformer complete all as specified and directed by Engr-in-Charge.

All as per item No 69 above but from 630 KVA to 1000KVA complete all as specified and directed by Engr-in-Charge.

Taking down defective unserviceable LT bush porcelain insulator and supply and fix news LT bush porcelain insulator with oil seal for transformer outdoor/indoor up to 500KVA complete all as specified and directed by Engr-in-Charge.

All as per item No 71 above but from 630 KVA to 1000KVA complete all as specified and directed by Engr-in-Charge.

Taking down defective unserviceable HT bush porcelain insulator and supply and fix news HT bush porcelain insulator for transformer outdoor/indoor up to 500 KVA complete all as specified and directed by Engr-in-Charge.

All as per item No 73 above but from 630 KVA to 1000KVA complete all as specified and directed by Engr-in-Charge.

Isolating the HT supply of transformer, disconnecting HT and LT connections of transformer by opening clamps, bus bar extension and isolating the cables from transformer, outdoor/Indoor of 200 to 500 KVA capacities, checking of transformer pressure release valve, oil condition and carrying out tests such as HV/LV megger test, ratio test, magnetic balance test, short circuit test including opening theinspection cover/top lid after drain out of oil as required to check the lead condition from winding to bus rods including necessary soldering/jointing etc, and charging of transformer and making all necessary connections / assembly & control circuits complete all as specified and directed by Engr-in-Charge. Note :- Test results shall be submitted through the Engineer-in-charge to Accepting Officer.

All as above item but no.75 of capacity 630 KVA to 1000KVA complete all as specified and directed by Engr-in-Charge.

Lifting of transformer core of capacity 160 to 750 KVA and keeping the core inside oven chamber to removing of moisure and increasing of the insulation value of core and drying the core assembly for minimum 3 days at a temp of 120oC Note :- (a) Cost for lifting/lowering the core of transformer by crane is inclusive. (b) Labour for fixing the connection/removal of connection inside the heating chamber is inclusive. (c) Power consumption for heating core for improving insulation value is inclusive. (d) Temperature 120oC to be maintained and inclusive in rate quoted.

Disconnecting defective out door/indoor transformers, 11KV/433 V of various capacities up to 1000 KVA from HT/LT sides taking down transformer oil completely, storing oil in suitable container (to be provided by the contractor), lifting the top cover and core assembly carefully and checking the conditions, refilling the transformer oil completely after necessary repairs, re-taking core assembly and fixing the top cover and painting to transformer complete all as specified and directed by Engr-in-Charge. Note (a) Rewinding of transformer shall be measured and paid separately. (b) In case of major repairs/replacement in transformer, which can not be undertaken at site, the transformer shall be shifted to civil workshop and winding and connected accessories (complete transformer) (c) Dismantling of core and repairs shall be measured and paid separately. (d) Shifting of transformer shall be measured and paid separately. (e) Complete gaskets shall be replaced by the contractor rate deemed to be inclusive.

Taking down burnt defective high tension copper coil and supply and fix new HT copper coil made out of proper/ required as per the existing size copper wire enameled of high quality matching with the existing impedance and pre- insulation complete all as specified and directed by Engr-in-Charge. Note : (a) The cost of coil shall be inclusive of varnish sleeving of insulating material. (b) Cost of taking down the clamps, upper channels and core & HT links and re-clamp, positioning with separators, brazing etc completely shall be deemed to be included in the cost.

All as per above item no.79 but of LT copper coil complete all as specified and directed by Engr-in-Charge.

Taking down and opening of HT copper wound loose overheated coil from the limbs of transfomer of various capacities upto 1000KVA, and rewinding the same by using the same copper wire after providing DPC and proper insulation etc into the coil of suitable turns etc all as specified and directed

All as per Item No 81 above, but of LT copper wound complete all as specified and directed by Engr-in-Charge.

Taking down unserviceble tinned copper bus bar of various sizes from HT/LT side cable bushing rods from the transformer of capacities and supply and fix electrolyte tinned copper bus bar of suitable size and length including making holes as required at site to the transformer LT/HT side cable bushing rods complete all as specified and directed by Engr-in-Charge.

Taking down the Defective tap changer assembly ,Supply and fix offload tap changer assembly suitable for any make upto 750KVA transformer with 5 tapping position including opening top cover, conservator etc complete all as specified and directed by Engr-in-Charge.

Opening of the RMU any size/way , 11 KV 400 to 800 Amps of any make by removing of the Breaker from the existing position after disconnecting all the connections from the system, servicing, Overhauling of the same, checking of the same for proper operation, spring charge, charged control cables are fastened tightly to the terminals, any abnormality, RMU, cleaning the surface of the insulators, fasten the bolts, checking and correcting interrupting units, mechanism, linkages etc, fasten the hardwares of control wiring, check that the split pins, Circlips, dowell pins etc. have not come out and are intact, lubricate the mechanism, moving parts by castrol, all purpose grease or equivalent, check that the vaccum pots/chambers is within limit including opening of the shutters properly, replacing of the trip catch, roller, holding catch, stopper, close push button, closing cum reassembling, controll limit switches reconnecting of the breaker for smooth functioning complete all as specified and directed by Engr-in-Charge.

Repairing of DC High Voltage Test Set Capacitiesup to 70 Kv for repairs, servicing comprising the following and refixing the same, re-orientation and labour for taking down the defective parts and refixing the same spare parts all as specified and directed Opening the DC High Voltage Test Set for repair and replacement of the following items Earth Leakage Relay With Core Balance Current Transformer Push Button Switch Element Red color. Tripping System for High voltage 10KV/30mA High voltage copper single core lead with Armour Silicon Carbide Schottky Diodes Multi span sequential Timer digital type ASPA DC array junction box DCDB 2 IN 1 OUT 500V LT On / Off Toggle Switch Elemet High voltage test cable Digital multi-function meter with LCD display KV Meter digital type Digital ammeter LED display 230volt,50Hz Calibration of the System with Calibration machine for earth fault and over current fault complete testing Top Cover

Repairing of DC Battery Charger of Capacities up to 110V, servicing comprising the following and refixing the same, re-orientation and labour for taking down the defective parts and refixing the same spare parts complete all as specified and directed by Engr-in-Charge. Opening the DC 24 V battery Charger for repair and replacement of the following items Volt meter and Ampere Meter Wiring Diode circuit Relay Control Transformer Rotary Switch

Supplying and laying in replacement synthetic Rubber insulated mats 2.5mm thick for voltage up to 11 Kv (size 2x1 M) for elctrical purpose as per IS 15652-2006, superseding IS 5424) suitable for electrical shock safety complete all as specified and directed by Engr-in-Charge.

M&L for repairing/ Plastring of Transformer platform of size 2.2mx2.2mx1 m height built in CM 1:4 including 20mm graded stone aggregate over the plinth along with provn of stair case on one side complete all as specified and directed by Engr-in-Charge.

M&L for checking the existing pressure of SF6 Gas in gas chamber of 11 KV, 630 Amps RMU, 3/4/5 way before filling and topping up to the SF6 gas in the chamber of RMU including supervision of gas filling /topping up process and checking the pressure of gas after filling complete all as specified and directed by Engr-in-Charge.

Supply Only of silica gel complete by removing the unserviceable silica gel complete all as specified and directed by Engr-in-Charge.

Material and Labour for complete removal of Stone aggragerate and removing of sand mud. Debris/ weeds and plants from the agraggate and relaying at the removed place complete all as specified and directed by Engr-in-Charge.

S & F in replacement battery 12V, DC, 100 AH maintnance free dry battery complete all as specified and directed by Engr-in-Charge.

M&L in replacement existing RCC duct cover with mild steel chequered plate 10 mm thick incliding cutting of suitable size for duct cover at site complete all as specified and directed by Engr-in-Charge.

Material and labour for preparation of old painted surfaces of indoor/outdoor typeLt Panel any size/ capacity by cleaning/rubbing with course cloth wire brushes to remove dust deposits oil grease and repainting by applying one coat of spray paint with synthetic enamel paint of approved colour without disturbing/damaging the electrical net work system/equipment complete all as specified and directed by Engr-in-Charge.

Note : Contractor should procure and provide 50 % of the material as listed above within 15 days of the placing of work order and shall be verified by the Engr-in-charge.

MV Engineers And Contractors (BID ID -3453065)

KISHORE ENTERPRISES (BID ID -3460491)

ALLIED CONSTRUCTION (BID ID -3460498)

Ridhi engineers and builders (BID ID -3455708)

Vijay Electricals (BID ID -3455142)

mayur enterprises (BID ID -3451026)

SB ENTERPRISES (BID ID -3454811)

BLUE HILL ELECTRICAL AND ELECTRONICS (BID ID -3455366)