SPL REPAIR TO MES OFFICE BLDG NO. T3, T4, T5, T6, T7 AND T8 AT AYODHAY UNDER AGE (I) AYODHYA CANTT

Amount

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) aea exc 1.50 Sqm but n.exc 4.00 Sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) aea n.exc 1.50 Sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down shutter exc 1.00 Sqm but n.exc 2.00 Sqm each leaf complete all as specified and directed by Engineer-in-Charge.

S&F 125 x 60mm pressed steel frame for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed by Engineer-in-Charge.

M&L PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in cills, copings, bed blocks, filling in pressed steel door frames and the like complete all as specified and directed by Engineer-in-Charge.

S&F 35 mm thick factory made flush shutters, factory moulded designed on both sides and fixed in position complete all as specified and directed by Engineer-in-Charge. Note: Designe & Colour shall be approved by Engineer-in-Charge / AGE (I).

S&F 2nd class hard wood 35 mm thick factory made and skeleton shutters, open rebated and prepared to receive glass, gauze, etc, divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, with and including stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm, sizes of members shall be as shown on drawing complete all as specified and directed by Engineer-in-Charge. Note: Design & Drawing of skelton shutter shall be approved by Engineer-in-Charge / AGE(I).

S&F in repairs, stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

S&F 150mm long stainless steel handle for door complete all as specified as directed by Engineer-in-Charge

S&F 200mm long stainless steel barrel tower bolt complete all as specified as directed by Engineer-in-Charge.

S&F 300 mm stainless steel sliding door bolt with hasp, staple (bolt type) and fixed with & including a minimum of six stainless steel bolts & nuts, four on bolt plate and two on staple plate complete all as directed by Engineer-in-Charge.

M&L for preparation of new steel & iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chromate primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one pink primer complete all as specified and directed by Engineer-in-Charge.

S&F 300mm, Mild Steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

S&F 100mm long butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed by Engineer-in-Charge.

S&F factory made single extruded WPC (WOOD POLYMER COMPOSITE) solid door / window / ceosetory window and other frame / chowkhat of size 50x100mm comprising of virgin PVC polymer of K value 58 to 60 (suspension grade), calcium carbonate and natural fibre (wood powder / rice husk / wheat husk) and non toxic additives) (maximum toxicity index of 12 for 100 grms) complete all as specified and directed by Engineer-in-Charge.

S&F factory made 30 mm thick single extruded WPC wood polymer composite and decorative type flush door shutter, comprising of virgin polymer of K value 58-60 suspension grade calcium carbonate and natural fibre (wood powder / rice husk / wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 grms) complete all as specified and directed by Engineer-in-Charge.

S&F powder coated anodised aluminium window / ventilator three track sliding type shutter with styles, rails size 40mm x 20mm, frame made of powder coated aluminium section of size 30mm x 90mm suitable for three track sliding shutters with and including 4mm thick frosted / tinted glass, necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws of suitable size etc and stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm, fixed with stainless steel wire staples to cover complete window / ventilator from outer side complete all as specified and directed by Engineer-in-Charge. Note: (i) Three Nos of track to be provided. (ii) The quoted rate will include cost of frosted / tinted glass, stainless steel wire gauge, locking arrangement etc complete and nothing extra to be paid on this account. (iii) Thickness of aluminium section shall not be less than 1.00 mm

S&F 140mm floor door stopper of aluminium alloy body and tongue with hard drawn steel spring complete all as specified and directed by Engineer-in-Charge.

Dismantling old floor / wall tiles of any description including cement mortar bedding but not backing, removing serviciable tiles to store and rubbish off the premises complete all as specified and M&L for new double charged Vitrified Ceramic tiles 08 mm thick (square/ rectangular), polished area of each tile exc 0.42 Sqm but n.exc 1.00 Sqm, laid in flooring over & including 15 thick screed bed in cement mortar (1:6), set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 20.00 above but in vertical surfaces as in dado skirting, fixed over & including 10mm thick rendering in cement mortar (1:4).

Dismantling old floor/ wall tiles of any description including cement mortar bedding but not backing, removing serviciable tiles to stores and rubbish off the premises complete all as specified and M&L for non-skid ceramic coloured tiles 7mm to 8mm thick (Square/rectangular), area of each tile n.exc 0.36 Sqm, laid in flooring over & including 15 thick screed bed in cement mortar (1:6), set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed by Engineer-in-Charge.

Dismantling old floor / wall tiles of any description including cement mortar bedding but not backing, removing serviciable tiles to store and rubbish off the premises complete all as specified and M&L for glazed ceramic coloured tiles of size 600x300x8 mm thick in vertical surfaces as in dado / skirting, fixed over & including 10mm thick rendering in cement mortar (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed by Engineer-in-Charge.

Taking down cement or cement lime plaster on brick or stone walls or ceiling etc including racking out joints, hacking for key, scrubbing down with water etc and M&L for 15mm thick rendering on fair faces of brick work in cement mortar (1:4) mixed with water proofing compound (liquid) as per manufacturer's instructions, finished even and fair on exernal surfaces of walls complete all as specified and directed by Engineer-in-Charge. Note : Water proofing compound shall be measured and paid for separately at supply only rates.

Supply only liquid water proofing compound of approved quality complete all as specified and directed by Engineer-in-Charge.

Taking down cement or cement lime plaster on brick or stone walls or ceiling etc including racking out joints, hacking for key, scrubbing down with water etc and M&L for 10mm thick rendering in cement mortar (1:6) on brick/ concrete surfaces of any description, finished even and fair on internal surfaces of walls complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work / stone masonary built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

M&L for 15mm thick plaster in cement mortar (1:4) on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer including 1mm thick wall care putty complete all as specified and directed.

M&L for complete removal of existing decorative treatment of any description on walls and applying two coats of oil bound distemper over a coat of primer and 1 mm thick wall care putty complete all as specified and directed by Engineer-in-Charge.

M&L for preparing newly plastered or unplastered surfaces of walls and applying two coats of exterior emulsion paint over a coat of wall care putty not less than 01 mm thick including a coat of exterior wall primer complete all as specified and directed by Engineer-in-Cjharge.

M&L for complete removal of existing decorative treatment of of any description on old plastered or unplastered surfaces of walls and applying two coats of exterior emulsion paint over a coat of wall care putty not less than 01 mm thick including a coat of exterior wall primer complete all as specified and directed by Engineer-in-Cjharge. Note : (a) Exterior primer & acrylic emulsion paint to be applied on wall surfaces by using Airless spray technology with working pressure of 3300 PSI and capable of operating single spray gun with max material hose length of 30 mtr. The spray machine shouild be of reputed manufacturer with pro gaurd technology and capability of tracking pressure. (b) Allow 6-8 hrs to dry the surface before applying subsequent coat.

S&F 5mm thick PVC wall lining of wood grain printed PVC Sheet inclusive of solvent cement and fixing on & including 35mm wide x 5 mm thick PVC fillet frame of grid size 300mmx300mm complete all as specified as directed by Engineer-in-Charge.

Dismantling of wall and ceiling boards (fiber pulp insulation etc) or insulation boards / slabs / blankets of any thickness including cover fillets complete all as specified and directed by Engineer-in-Charge.

S&F powder coated anodised aluminium snap grid frame work for false ceiling complete all as specified and directed by Engineer-in-Charge.

S&F hanger of 6mm dia GI wire (upto 1200mm length) ajusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fastner complete all as specified and directed by Engineer-in-Charge.

S&F 4mm thick high pressure steam cured non asbestos fibre cement building boards, fixed or laid/inserted to timber/GI/Aluminium frame work with screws complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, 15mm dia bore bib taps with wall flange, fancy type, cast copper alloy with capastan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge. Make - Jaquar Cat Part No. FUS 29037 or equivalent as approved by Engr-in-Charge / AGE (I).

S&F in repairs, 15mm dia bore two way bib cock with wall flange, fancy type, cast copper alloy with capastan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge. Make - Jaquar Cat Part No. FUS 29041 or equivalent as approved by Engr-in-Charge / AGE(I).

S&F in repairs, 15mm dia bore angle valve chromium plated, fancy type with capastan head, screwed down, hogh pressure, screwed for iron pipe or for brass ferrule at both ends complete all as specified and directed by Engineer-in-Charge. Make-Jaquar cat part No. FUS 29053 and equivalent

S&F in repairs, toilet paper holder with flap and fixed complete all as specified and directed by Engineer-in-Charge. Make- Jaquar at part No. CAN-1153S or equivalent as approved by Engr-in-Charge / AGE(I).

S&F in repairs, 15mm bia bore PVC connection pipe of 600mm length with PTMT nuts at both ends and fixed complete all as specified and directed by Engineer-in-Charge.

S&F towel ring square shape complete all as specified and directed by Engineer-in-Charge. Make- Jaquar Cat Part No. ACN 1121N or equivalent as approved by Engr-in-Charge / AGE(I).

S&F corner glass shelf with bracket complete all as specified and directed by Engineer-in-Charge. Make- Jaquar Cat part No. ACN-1173 or equivalent as approved by Engr-in-Charge / AGE(I).

S&F in repairs, looking mirror 5 to 6 mm thick fixed on 8mm thick commercial decorative water proofing ply wood with coloured PVC frame all around and hook and fixed complete all as specified and directed. Note - Shade of frame as approved by Engr-in-Charge / AGE (I)

S&F in repairs, vitreous china wash hand basin white flat back of size 550 x 400 mm excluding tap, waste chain and plug but including bracket, waste coupling of 32 mm size complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, vitreous china wash down water closet pan pedestral pattern, white, including 10 ltrs PVC valveless, syphonic action type, low level flushing cistern, white with inlet, ball valve, float and handle including brackets, flush pipe of polythylene of low or high density or PVC 32mm dia, Plastic water closet seat, closed pattern with recessed bottom, and cover with mild steel chromium plated or aluminium hanging device complete all as specified and directed by Engineer-in-Charge. Make - Jaquar or equivalent as approved by Engr-in-Charge / AGE (I)

S&F in repairs, vitreous china squatting pan, Orissa pattern of size 580mm x 440mm with integral foot rest including connection to trap and to flush pipe, anti-syphonage pipe etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, 10 Ltrs capacity PVC valveless, syphonic action type, low level flushing cistern, white, with inlet, ball valve, float & handle, flush pipe of polythylene of low or high density or PVC 32mm dia including brackets complete all as specified and directed by Engineer-in-Charge.

Taking up or down old 15 mm dia bore steel tubing and connection and removing the same from site / keeping aside for reuse complete all as specified and S&F new 15mm dia bore steel tubing, medium weight, ISI marked, galvanized with all fittings and fixed to walls, ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 50.00 above but 20 mm dia bore steel tubing

Taking down eaves, gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) and S&F new 75mm PVC (SWR) pipes single socketed, fixed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, 75mm PVC floor trap plain with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

S&F interior vertical vanishing blinds for windows including all accessories and fittings of superior quality as approved complete all as specified and directed by Engineer-in-Charge.

Dismantling plain or corrugated Asbestos Cement (Corrugated, semi-corrugated etc) sheets in roof covering complete all as speciifed and S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa of AZ 150 as in roof covering/cladding to wall and rain water gutter fixed with self tapping screws, complete all as specified and directed by Engineer-in-Charge.

S&F 12 mm toughened glass as in hinged doors, partitions, automatic doors and similar work including cutting to shape, drilling holes and necessary handle for opening complete all as specified and directed by Engineer-in-Charge.

Taking down caefully switch board with old MS rectangular sunk type box heavy/medium duty of size 1 to 12 module from the existing position along with switches, sockets, regulators etc by un-screwing from board by disconnecting electric connections without damaging existing circuit and conduit complete and reconnecting all connection after comletion of job with making good the disturbed surfaces to match the existing surfaces complete all as specified and directed by Engineer-in-Charge.

Taking down copper/aluminium point wiring for (light, fan, socket or power) including unserviceable fittings such as switches, socketes, ceiling rose, holder, light fittings etc and making good the disturbed surfaces of wall / floor etc complete all as specified and directed by Engineer-in-Charge. Note- (i) Dismantled serviceable light fittings shall be kept in safe custody for reuse. (ii) Refixing of serviceable fittings shall be paid seperately under relevant item.

Refixing of serviceable light fittings upto 22 watt obtained form item No. 58.00 including connecting up with 3 core flexible cable copper conductor of suitable size from ceiling rose complete all as specified and directed by Engineer-in-Charge.

Taking down ceiling /exhaust fan from existing position and removing the same to MES store and refixed in the same position after completion of work and connecting up with 3 core flexible cable copper conductor of suitable size complete all as specified and directed by Engineer-in-Charge.

Taking down old and unserviceable sub main wiring of any size / type / core including earth wire with batten conduit etc complete all as specified and directed by Engineer-in-Charge.

Taking down old and unserviceable sheet metal enclousure, switch fuse unit, distribution board of any type / way / capacity including fuses MCBs, insulator RCCBs etc copmlete after removing all connection and making good the disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for metal flush boxes suitable for 3 to 4 modules including modular front cover plate & back plate for mounting modular type switches / socket / fan / regulator etc complete all as specified and directed by Engineer-in-Charge.

M&L for metal flush boxes suitable for 6 to 12 modules including modular front cover plate & back plate for mounting modular type switches / socket / fan / regulator etc complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring with two single core PVC insulated & PVC unsheathed FRLS-H multistranded copper conductor cable of size 1.5 Sqmm 1100 Volt grade in non metallic rigid PVC concealed conduit medium grade 20/25 mm dia with all accessories mounting on wall / ceiling / roof etc with suitable size of modular metal flush boxes including front cover plate & back plate for mounting modular type switches / socket / fan regulator etc including provision of one single core PVC insulated and unsheathed multi stranded copper cable of size 1.5 Sqmm 1100 Volt grade as earth continuity conductor connected to common earth dolly switch board complete for the following :-

One light/fan point controlled by one 5 Amps, 240 Volt single pole switch

One bell/buzzer point controlled by bell push

One 3 pin 5 Amps switch socket outlet point on independent board.

One 3 pin 5 Amps socket point on the same board

All as per Srl item No. 65.00 here-in-before but with 2.5 Sqmm conductor for 5 pin 15 Amps switch socket outlet complete all as specified and directed by Engineer-in-Charge.

S&F switch modular type 1 module single pole, one way 5 Amps complete all as specified and directed by Engineer-in-Charge.

S&F switch modular type 1 module single pole, one way 15 Amps complete all as specified and directed by Engineer-in-Charge.

S&F socket outlet 2 in 1, 5 pin, 15 Amps modular type 2 module complete all as specified and directed by Engineer-in-Charge.

S&F socket outlet 5 Amps modular type 2 module complete all as specified and directed by Engineer-in-Charge.

S&F Bell push 5 Amps complete all as specified and directed by Engineer-in-Charge.

M&L ceiling rose, PVC / polycarbonate, isolated body complete all as specified and directed by Engineer-in-Charge.

S&F stepped type electronic fan regulator modular type 1 module complete all as specified and directed by Engineer-in-Charge.

S&F bell wall mounted ,ding dong type AC, 230 Volt, single pole complete all as specified and directed by Engineer-in-Charge.

S&F submain wiring with two single core PVC insulated FRLS-H multistrand copper conductor cable of size 4.00 Sqmm drawn into and including non metallic medium duty rigid concealed PVC conduite not less than 25 mm size ISI marked with all fittings / accessories and 4.00 Sqmm FRLS-H multistranded copper conductor cable as continuous earth wire complete all as specified and directed by Engineer-in-Charge. Note :- for submain wiring: Two run of single core cable and one run of earth wire shall be measured as one length and conduit and its accessories is deemed to be included in the unit rate quoted for this items.

S&F submain wiring with two single core PVC insulated FRLS-H multistrand copper conductor cable of size 10.00 Sqmm drawn into and including non metallic medium duty rigid concealed PVC conduite not less than 25 mm size ISI marked with all fittings / accessories and 10.00 Sqmm FRLS-H multistranded copper conductor cable as continuous earth wire complete all as specified and directed by Engineer-in-Charge. Note :- for submain wiring: Two run of single core cable and one run of earth wire shall be measured as one length and conduit and its accessories is deemed to be included in the unit rate quoted for this items.

S&F sheet metal enclosure TPN, 4 way, 415 Volt double door MCB distribution board complete all as specified and directed by Engineer-in-Charge.

S&F sheet metal enclosure SPN 240 Volt 12 way double door MCB distribution board complete all as specified and directed.

S&F MCB TPN 63-100 Amps 415 Volt rupturing capacity 10 KA 'C' series complete all as specified and directed by Engineer-in-Charge.

S&F MCB SPN 32 to 40 Amps 240 Volt, 50 htz,10 KA breaking capacity 'C' curved type complete all as specified and directed by Engineer-in-Charge.

S&F MCB SP, 6 to 32 Amps, 240 Volts 50 htz, 10 kA breaking capacity complete all as specified and directed by Engineer-in-Charge.

S&F socket outlet 5 pin 20 Amps modular type 2 module with suitable size metal flush boxes including modular front cover plate and back plate for mounting modular type switch & socket with one single pole one module MCB of 20 Amps including electrical connection all as specified and directed by Engineer-in-Charge.

S&F square recessed / surface / suspended mounting LED ceiling light with extruded aluminium housing and milky diffuser of 36 Watt 2'X2' panel with LED driver 240 Volt, 50 htz, 3600 lumen 6500 k complete all as specified and directed by Engineer-in-Charge.

S&F LED light fittings 1x20 watt, 220 volt AC decorative box type with driver holder including 18 watt LED tube light connecting up with 3 core flexible cable copper conductor of suitable size from ceiling rose complete all as specified and directed by Engineer-in-Charge.

S&F sleek LED mirror light decorative wall mounted 10 watt rating with diffuser 2' long twisted flexible copper wire (approx 0.5 mtr long) complete all as specified and directed by Engineer-in-Charge.

S&F LED security light 45 watt with security light bracket (complete with two set of clamp, nut & bolt) made out of 40 mm medium grade GI pipe bent to shape with fixing arrangements duly welded (length of pipe should not be less than 1.20 mtrs) and making conection using 1.5 Sqmm PVC insulated multistranded copper conductor two single core cable complete all as specified and directed by Engineer-in-Charge.

Supply, fabrication, errection, installation, testing and commissioning of cubical, outdoor type CPRI approved LT feeder piller Box totally enclosed weather and vermin proof, factory made fully compartmentalised made out of 3.15 mm thick CRCA steel sheet for load bearing and 2 mm thick for non load bearing portions. Protection of enclosure IP-54 complete with two coats of synthetic enamel paint over one coat of red oxide primer including suitable angle flat iron frame work for supports, necessary earth work, PCC foundation (mini 45 cm high from GL), making all incoming and outgoing connections with suitable size copper cable including cable lugs , cable gland etc with one MCCB, 3 phase and neutral, 415 Volt thermal magnetic type, 4 ploes, rating 160 Amps with rupturing capacity 25 kA - 1 No. complete all as specified and directed by Engineer-in-Charge.

Supply, laying and testing 25 Sqmm 4 core, XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty), 1100 Volts grade with stranded aluminium conductor complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches in soft/loose soil n.exc 1.5m wide and n.exc 1.5m in depth and getting out for laying of cable / foundation of pole & stay etc complete all as specified and directed by Engineer-in-Charge.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm in thickness in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Removing of surplus excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed by Engineer-in-Charge.

M&L for precast cable cover class LV type 1 flat size 250x150x40 mm, laid flat, dry butt jointed, laid lengthwise perpendicular to the axis of cable complete all as specified and directed by Engineer-in-Charge.

M&L for dry sand cushioning for protection of LT underground cable including punning below & above the complete all as specified and directed by Engineer-in-Charge. Note : Thickness of sand cushioning shall be measured as 18 cm.

S&F end termination kit with jointing material heat shrink type and accessories suitable for 4 core XLPE armoured, Aluminum conductor cable of size 16 to 25 Sqmm indoor / outdoor type complete all as specified and directed by Engineer-in-Charge.

Supply and laying DWC HDPE pipe of OD/ID 77mm/63mm bore medium class ISI marked double wall corrugated for laying open / underground cable protection including cutting of road / hard standing etc and making good the surface to match existing one complete all as specfied and directed by Engr-In-Charge. Note: (a) Using of GI clamp in wall/drainage rate are deemmed to be included in rate quoted.

M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including 15 mm bore light grade G.I. protection pipe (upto 7.5 M beyond outer edge of earth pit) PCC pit in mix (1:3:6) type C1 with 40mm thick cover made of RCC (1:2:4) type B-1 reinforced with 6 mm dia M.S bars 3 Nos each way with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work etc complete all as specified and directed by Engineer-in-Charge.

Saket Traders (BID ID -3353407)

ABC CONSTRUCTION CO. (BID ID -3353528)

M/s Sultan Khan (BID ID -3353463)

K R KAUSHAL AND SONS (BID ID -3353534)