PROVN OF TOILET BLOCK WITH URINALS PTS NEAR SINGLE LIVING ACCN OF HQ 31 SUB AREA AND CERTAIN REVENUE AND MINOR WORKS AT BB CANTT SRINAGAR

Amount

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation etc n exc 10 sqm on plan and getting out in hard/dense soil complete all as specified and directed.

Returning filling in including spreading leveling watering and well ramming in layers n exc 25cm complete all as specified and directed.

Removal of excavated materials to a distance n. exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

M&L for brick work with sub class 'B' brick straight or curved on plan exc 6m mean radiaus built in cement mortor 1:6 complete all as specified and directed.

M&L for brick work with sub class 'B' bricks on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and directed.

M&L for rolled mild steel as in roof trusses (framed), trussed, purlins, rafters etc, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe -410-W (gde-E-250) Quality 'A' complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick work/concrete surfaces in CM 1:4 finishing the surface even and fair complete all as specified and directed.

M&L for preparing newly plasterd surfaces of wall and applying two coats of cement based paint complete all as specified.

M&L for 10mm thick plaster in CM 1:4 on other than fair faces of brick work finishing the surface even and fair complete all as specified and directed.

M&L for preparing newly plasterd surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for RCC (nominal mix), 1:2:4, type B-1, (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, eck slabs and in shelves and the like complete all as specified and directed.

M&L for RCC (nominal mix), 1:2:4, type B-1, (using 20mm graded crushed stone aggregate) as in beams, lintels, cantilever etc supported on walls, beams and columns and like complete all as specified and directed.

M&L for 10 mm dia and over mild steel TMT bars, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelvves including sup-ports, overhangs, etc. also splays between floors and beams, etc finish with rough finish flat surface complete all as specified and directed.

Form work to soffits of suspended slab, roof slab, landings and similar work, n exc 200mm thick (Horizontal or sloping) for rough finished surface complete all as specified and directed.

M&L for hardcore ( broken stone or boulders) of gauge n exc 63 mm deposited spread and leveled in layers n exc 15 cm thick watered and rolled / rammed to a true surface complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate as in plinth protection, finished concrete surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in sub base under floor and finished rough surface complete all as specified and directed.

M&L for 15mm thick screed bed in cement mortar 1:6, finished rough for laying floor finishes complete all as specified and directed.

M&L for coloured glazed ceramic tiles on vertical surface as in dado, skirting etc of size 350mmx250mmx7mm/450mmx350mmx7mm set and jointed in neat cement slurry and pointed in white or colour cement to match fixed over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for coloured Non - skid Ceramic tiles 7-8mm thick (square/ rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.36sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in in ridges, hips, valley gutters, drip fixed with self tapping screws complete all specified and directed.

S&F 2nd class hard wood, plain, solid, straight chowkats or frames, wrought framed rebated on the solid, rouned or chamfered, put together with flue pinned at joints complete all specified and directed.

S&F 35mm thick 2nd class hard wood plain framed panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board with commercial face veneers complete all as specified and directed.

S&F soild PVC door frame of size 50mm x 47mm made out of 5mm plaint colour PVC sheet reinforced with MS square tube, and fitted in opening complete all specified and directed.

S&F factory made solid PVC moulded door shutter with particle board core 28 to 30mm thick (style) with 2, 4, or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face and fixed in frame at site complete all specified and directed.

M&L for mild steel hold fast of flat Iron size 25mm x 3mm thick for PVC door chowkhat etc complete all specified and directed.

S&F 100mm long stainless steel butt hinges medium weight complete all specified and directed.

S&F Aluminium handles cast type anodised 100mm long complete all specified and directed.

S&F 200mm long aluminium alloy, anodised, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all specified and directed.

S&F steel ventilator with top hung shutter including hinges steel peg stay complete with one shop coat of zinc chromate primer complete all specified and directed.

S&F 150mm long aluminium barrel tower bolts of extruded section and fixed, complete all specified and directed.

M&L for preparation of new wooden surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for 18-20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete in partition for urinal complete all as specified & directed.

S&F anodised aluminium snap grid frame work for false ceiling having size of grid 605x605mm including hangers 6mm dia G.I (upto 1200 mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of G.I flat 40x3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long and providing and fixing decorative designed patten (as approved) Gypsum board 12mm thick in ceiling fixed with screw or as per manufacturers instructions complete all as specified and directed.

M&L for Vitreous china water closet pan (pedestal pattern), white with seat cover and hinging device, fixing bolts etc (excluding flushing cistern and including flush pipe) complete all as specified and directed.

S&F Vitreous China squatting pan "Orissa Pattern" size 580 x 440mm white with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F vitreous china bowl urinal flat back of size 465x355x265mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including discharge pipe of PVC 32mm dia complete all as specified and directed.

S&F vitreous china wash basin, white, flat back, size 550x400mm including cutting for and pinning in ends of brackets or erecting stand including waste chain & plug and porcelean stopper and brackets, waste pipe, complete all as specified and directed.

S&F 32mm bore waste coupling of PTMT (half or full threaded) suitable for urinal with PVC flexible pipe 25 mm dia. ( Minimum weight 32mm-45 gms) complete all as specified and directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F 10 ltr capacity PVC valveless syphonic action type flushing cistern, low level, white with inlet ball valve float and handle incl brackets, flush pipe etc fixed complete all as specified and directed.

S&F 32mm bore waste coupling of PTMT (half or full threaded) suitable for wash hand basin. (Minimum weight 32mm-45gms) complete all as specified and directed.

S&F Stop/Angle valve 15mm bore, cast copper alloy screwed down, high pressure, with crutch jor butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F PVC (SWR) floor trap 75mm dia outlet, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 15mm bore bib tap cast copper alloy chromium plated fancy type with crutch of butterfly handle, screwed down, screwed for iron pipe of for brass ferrule complete all as specified and directed.

S&F PVC connection 15mm dia and 600mm long with PTMT nuts and washer complete all as specified and directed.

S&F 15mm bore CP fancy type mixture tap for mixing hot & cold water with centre hole mixer with fittings complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F PVC (SWR) gully trap square or round mouthed type (P), size of trap 125x110mm and jointing to drains with solvent cement complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F Soap dish chromium plated, any type, fixed to wall with chromium plated brass screw complete all as specified and directed.

S&F tubular towel rail 60cm long, 'D' type, aluminium anodised fixed with and including CP brass screws and wooden/plastic cleats complete all as specified and directed.

S&F 20mm dia steel water tubing medium grade galvanized with all fittings and fixed complete to walls, ceilings or laid on floors, complete all as specified and directed.

S&F 15mm dia steel water tubing medium grade galvanized with all fittings and fixed complete to walls, ceilings or laid on floors, complete all as specified and directed.

M&L for Lagging to pipes 15mmdia used in internal water supply or plumping all round with 25mm thick bonded mineral wool preformed 'SNAP ON' pipe sections of density 144 kg/cum conforming to IS-9842 complete all as specified and directed.

M&L for Lagging to pipes 20mm dia used in internal water supply or plumping all round with 25mm thick bonded mineral wool preformed 'SNAP ON' pipe sections of density 144 kg/cum conforming to IS-9842 complete all as specified and directed.

S&F CP steel grating 75/100mm dia complete all as specified and directed.

S&F 1000 litres capacity rotational moulded polye-thylene water storage tanks three layers (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F 20mm boe ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm - 210 gms complete all as specified and directed.

S&F 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 15 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Excavation in post holes each not exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25 cm, watering, and removing surplus soil to a distance n.exc 50 Mtr and making good surface in any type of soil complete all as specified and directed.

M&L for rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

M&L for brick work with sub class 'B' brick straight or curved on plan exc 6m mean radiaus built in cement mortor 1:4 complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:4) on other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement mixed with and including water proofing compound as per manufacturer's instructions complete all as specified and directed.

S&F 150mm dia reinforced concrete pipes, class NP-2, laid and jointed in trenches with collar complete all specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in concrete bed to drain pipes of 150mm internal bore including packing under and hunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L for precast RCC (nominal mix) 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set in CM 1:4, including necessary formwork complete all as specified and directed.

M&L for Mild steel round bars 10mm dia as in handles for manhole cover complete all as specified and directed.

Cutting into existing manholes for connecting new drains of 100mm dia of pipe, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base/levelling course complete all as specified and directed.

M&L for prepolished chequered cement concrete tiles of size 25cmx25cmx22mm made by using vibratory mechanical system having glazed top layer with mixture of white cement and pigment, set jointed and pointed in neat cement slurry in floors laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

M&L for PCC (1:2:4) type B-2 using 40mm graded crushed stone aggregate as in surface channels and drains including necessary form work complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:4) on fair faces of brick work finished even and smooth with using extra cement complete all as specified and directed.

M&L for cutting of road as required (approx 9.25M each length) for laying RCC pipe line under road including repair/making good surface as per existing with filling of earth, boulders, WBM, BM etc and top surface finished with 30mm thick ready mixed patch filler complete all as specified and directed.

S&F 200mm dia reinforced concrete pipes, class NP-2, laid and jointed in trenches with collar complete all specified and directed.

Cutting holes in brick walls in cement mortar cutting exc half brick but not exc one brick for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all specified and directed.

S&F Stop/Angle valve 20mm bore, cast copper alloy screwed down, high kpressure, with crutch jor butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

Excavating over areas n. exc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:4 complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses, hammer dressing with maximum depression on face from straight edge held against the dressed surface n exc. 40mm of lime or sand stone complete all as specified and directed.

M&L for raised pointing to random or polygonal rubble, uncoursed or brought upto course in CM 1:3 complete all as specified and directed.

Supply only 110mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints, fixed as in weep holes complete all as specified and directed.

M&L for hand packing with broken stone or boulders(any thickness) at back of walls over arches etc. and raising (or lowering) to the required level complete all as specified and directed.

M&L for PCC (1:3:6) type C-1 using 20mm graded crushed stone aggregate as in bond stone complete all as specified and directed.

Surface dressing not exceeding 15cm deep and getting out in any type of soil, comlete all as specified and directed.

M&L for rendering 15mm thick in CM (1:6) on other than fair faces of brick work or concrete surfaces finished even and smooth witout using extra cement mixed with and including water proofing compound as per manufacturer's instructions complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for 100mm thick PCC (1:3:6), Type C-2 (using 40mm graded crushed stone aggregates) as in sub base, levelling course etc complete all as specified and as directed.

M&L for 40mm thick PCC (1:2:4), Type B-1 (using 20mm graded crushed stone aggregates) as in floor finished even and smooth with using extra cement including 3mm thick and 38mm wide glass dividing strips complete all as specified and as directed.

M&L for vitrified Ceramic (dark shade/double charged) tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.42sqm but not exceeding 1.00 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile fixed over and including 15mm thick screed bed in CM 1:6 complete all specified and directed.

S&F aluminium door air tight anodized frame made of size 100x45mm of sheet thickness 1.5mm with one or more rebate including jointing cleats hinges etc for fixing anodized aluminium door shutter fully paneled) two NOs of panel on each shutter) with 5.5 mm thick tinted plain glass shutter rail made of 80x45mm of sheet thickness 1.5mm (top, bottom, middle and side rail). Single/double leaf side hung type including necessary jointing cleats, anodized aluminium fittings such as aluminium butt hinges 100mm long 4 Nos on each shutter, aluminium anodized tower bolt 200mm long 3 Nos for each door, aluminium anodized handle 150mm, 2 Nos ‘D’ type for each shutter & lock 6 lever of make Harrison one on each door, bottom door spring one on each shutter including hydraulic door closer complete all specified and directed. All door fitting shall be ISI marked (size of each door shall be as per site requirement).

S&F wall mounted Cascade type EWC with all fittings and accessories all as per manufacturers instructions complete all as specified and directed.

S&F Vitreous china wash basin white, flat back of size 580x450mm excluding taps waste chain and plug and porcelain stopper but including brackets and 15mm bore CP centre hole mixer alongwith pedestal complete all as specified & directed.

S&F looking mirror of 5.5mm thick bevelled edge mirror of slected quality glass, mounted on wall with steel plugs with chromium plated brass screws and cup washers complete all as specified and directed.

S&F glass shelf 600mm long 125mm wide of CP complete all as specified and directed. Make :- Jaquar Cat Part No ACN-CHR-1171N or techno commercially equivalent make/model as approved by GE.

S&F toilet paper holder of stainless steel fixed to wall with chromium plated CP brass screw complete all as specified and directed Make:- Jaquar Cat Part No -AKP-CHR-35753PS or technocommercially equivalent make/model as approved by GE.

S&F liquid soap dispensor complete, all as specified and as directed. Make:- Jaquar Cat Part No - ACN-CHR-1135N or technocommercially equivalent make/model as approved by GE.

S&F stainless steel Towel Rack 600mm long complete all as specified and directed. Make:- Jaquar Cat Part No - ACN-SSF-1181FHS or technocommercially equivalent make/model as approved by GE

S&F flash touch-free infrared hand dryer, made out with 304 grade stainless steel, with 1150W rated power & carbon bush motor, stainless steel finish complete all as specified and directed. Make: - Jaguar cat No HDR-SSF-AK2807 or technocommercially equivalent make/model as approved by GE

S&F Angle/Stop valve15mm dia cast copper alloy, chromium plated, fancy type without shank and cup concealed type srewed for iron pipe or for union complete all as specified and directed.

S&F PVC flexible connections of PTMT 600mm long 15mm dia with flange nuts & washers complete all as specified and directed.

S&F tubular towel rail 60cm long, 'D' type, brass chromium plated fixed with and including CP brass screws and wooden/plastic cleats complete all as specified and directed.

S&F 15mm dia CP fancy type wall mixer for mixing hot & cold water with wall mounted fittings complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all specified and directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks & similar work con-forming to Fe.290.Gde-E-165 complete, all as specified and directed

S&F 75mm bore PVC (SWR) branch piece, single equal or unequalcomplete all as specified and directed.

M&L for point wiring with PVC insulated FRLS wire, 1100 volt grade with multistranded copper conductor wire of size 1.5 Sqmm (Nominal area) drawn through concealed in wall with heavy duty ISI marked PVC conduit of suitable size 20mm dia along with its all connected fittings accessories including providing of pressed steel terminal sunken boxes 1.2mm thick dully fixed concealed in wall and covered with electro plated 3mm thick plastic laminated sheet for housing / mounting of switches, sockets, regulators etc and also using /drawind of 1.5 sqmm PVC insulated FRLS wire , 1100 Volt grade with multistranded copper conductor wire used as a continuous earth wire which is connected with terminated the box to ceing rose / fitting complete and including making good to all disturbed surfaces of wall/ceiling and floor area of wiring system and to match the existing surface of wall/floor/ceiling etc. all as specified and directed for following:-

One light/fan point controlled by one way switch 5 Amp

One 3/5 pin socket outlet, 5 Amps on same board

One 3/5 pin socket outlet, 5 Amps on independent board

All as per Sl item No.123 above but using single runs of PVC insulated FRLS wire, 1100volt grade with multistranded copper conductor wire of size 2.5 Sqmm (Nominal area) power point wiring system with controlled by one way switch fixed on independent board and also providing of 2.5 sqmm PVC insulated FRLS wire , 1100 Volt grade with multistranded copper conductor wire used as continuous earth wire complete all as specified and directed

S&F piano switch 5/6 Amps 220 Volts for one way switching system complete as specified and directed.

S&F socket 5/6 Amps 220 Volts, 3/5 pin complete as specified and directed.

S&F piano switch 15/16 Amps 220 Volts for one way switching system complete as specified and directed.

S&F socket 15/16 Amps 220 Volts, 5/6 multi pin type complete as specified and directed.

S&F ceiling rose three terminals type made out of polycarbonate , isolated body complete all as specified and directed.

S&F wall mounted slim batten type decorative integrated design LED tube light fitting of rating capacity 1 x 20W/ 22W with eletronic driver and fitting extruded body made of aluminum housing with high quality polycarbonate diffuser with long life energy saving and required fitting used in both warm/white type coluor set complete including providing of suitable type of flat fexible two / three core cable for electric connection including taking down old fitting complete all as specified and directed. Make : Philips model No - BN021LED22S 6500K /4000K PSU GR, Havells model No.-LUMILINEPLUSNEOBS22WLED865SPCSSIND & Crompton model No-CCS-100-20-65-HL2-DP-NWH.

S&F decorative profile wall mounted LED mirror light fitting 20 Watt 6500 K of size 57.5CM long or 2 fit long with aluminium channel environmental friendly energy efficient and long life energy saving and required fitting use in both warm/white type colour set complete set complete set and including providing of suitable type of flat flexible two/three core cable and making electric connection and including taking down of old fitting all as specified and directed. Make of Havells & model -LHEXARP7IN1W020 or equivalent specification and model & make of Philips /Crompton

S&F environmental friendly LED street light fitting of rated capacity 20/25W out door type made out of pressure die cast hosing with glass and high performance polycarbonate optics with LEDs with drives and having IP 65/66 protection and surge to heat resistant sink for better heat dissipation and including to ready for use and required in both warm/white colour type fixture complete set including providing of suitable dia or as recommended by manufacturer GI pipe light grade bracket and it to match/setting the new fitting fixture hole attachment system of suitable bracket length upto 1.2 mtr long and make to shape / bend of 120 degree angle including duly fixed alongwith existing pole /bldg wall/ roof with the help of 02 Nos of MS fixing clamp alongwith nut bolt and including providing of suitable type of flat flexible two/three core cable and making electric connection and including taking down of old fitting all as specified and directed. Make of Philips & model No. BRP029 LED25 CW/WW MR PSU GR DX, Havells Model No.LHEXAYP7PN6K020, Bajaj Model No- ENXT P25L WH PO PC SD

S&F angular/batten type shape lamp holder with PVC/ Polycarbonate insulated body, alongwith brass adaptor and back plate for housing of bulb including providing of rechargable LED bulb of capacity 9 watt warm/ white colour type complete all as specified and directed .

S&F air circulation ventilating fan of size 300mm sweep single phase 220 volt AC and sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200 fixed on wall with nut, bolt including providing elecctric connection with suitable size copper wire compete all as specified and directed.

S&F electric water heater storage type steel body with inner copper tank of storage capacity 25 ltr, BEE 5 star rating and heating element upto 2 KW and providing all connecting accessories and electrical connection complete all as specified and directed.

S&F sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrangement system suitable of rating of size/type of distribution board SPN 4 way type 220 volt AC supply system with IP-43 protection system and having mounting channel with having suitable rating of copper bus bar and suitable size of common neutral and earth link and also making all necessary electrical connection and dully fixed surface on wall or concealed in wall with the help of cutting chases to wall for fixing of DB and making good the disturbed wall surface complete all as specified and as directed.

S&F MCB SPN 32 to 40 Amps, 230 Volts, 50 Hz AC supply suitable for 'C' series, 10 KA breaking capacity complete all as specified and directed.

S&F MCB SP 6 to 32 Amps, 240 Volts, 50 Hz AC supply suitable for 'C' series, 10 KA breaking capacity complete all as specified and directed.

S&F 1100 volts grade heavy duty twin core cable 10sqmm, PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire alongwith all fittings and connected accessories and dully fixed concealed in wall or surface on wall and electric connection complete all as specified and directed.

M&L for earthing, complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (Earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 mtr below normal ground level connecting to the galvanised iron earth lead wire of 4mm dia by means of bolts, nuts, check nuts and washers of galavanised iron and earth strip protected by provision of GI light grade pipe 20 mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded of stone aggregate with XPM (weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and with 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate common salt and charcoal filling test point made out of 40mm/6mm flat iron with fixing arrangement funnel wire mesh and earth work in hard dense soil returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electrical plate No 03 of SSR-2009 Part-I and connecting to earth test point complete all as specified and directed.

S&F surface mounted LED bulk head luminaries light fitting of rated capacity 10W out door type with dust and water proof, with PVC housing and unbreakable polycarbonate opal with inbuilt surge protection with IP 65/66 protection rating, energy efficient for ready to use and required in both warm/white type colour fixture complete including dully fixed on bldg wall surface including providing of suitable type of flat flexible two/three core cable and making electric connection and including taking down of old fitting all as specified and directed. Make of Philips & model No - WT202W LED10S Havells model No.HEXAFT10W LED857 SSYMBOPC, Bajaj model No. BIBWP 10W LED

S&F ventilating exhaust fan made out of sturdy engineering plastic body complete with louvers and shutter operational of size 250mm sweep suitable to work on 230 Volts 50 Hz, 1200 RPM, coper winding including making of suitable type /size of hole on wall and fixing compete with nut, bolt etc all as specified and directed.

S&F sheet metal enclosure duly powder coated with single pole and neutral enclosure with having a two pin and earth plug socket base & metal plug top and having mounting channel and complete with one MCB SP 20 Amp and making all necessary electrical connection and dully fixed surface on wall or concealed in wall with the help of cutting chases to wall for fixing of DB and making good the disturbed wall surface all as required at site complete all as specified and as directed.

S&F Sub main wiring system with two runs PVC insulated FRLS wire, 1100 volt grade with multistranded copper conductor wire of size 2x4Sqmm and one run of 1x4 Sqmm (Nominal area) (ISI Marked) as in earth wire any type any length drawn through in heavy duty ISI marked PVC Casing capping / PVC conduit of suitable size along with its all fittings and connected accessories and duly fixed concealed on wall or surface on wall complete all as specified and directed. Note:- 3 runs of 4sqmm wire and one run of PVC cassing capping/conduit shall be measured and 1.0 RM.

M&L for providing chemical earthing system, complete with using copper earth plate of size 90cmx60cmx5mm thick with copper strip 32mmx6mm. The earth plate buried directly in ground vertically to a depth not less than 5 meters deep below normal ground level. The size of earth pit shall not less than 1.6mx1.6mx5m depth. The arth plate resting on pointed end and the vertical top edge of plate not less than 4.0 mtr below normal ground level, the earth plate connected with copper earth strip means of brazing, jointing at two places with drilling holes for jointing each other by 10mm dia copper/brass bolts, nuts, check nuts and washers, the earth strip to be protected by provision of GI light grade pipe 40mm bore upto suitable length with suitable size/type MS clamp for holding of strip and GI pipe system from bottom level upto ground level and also making arrangement for inter connection strip work for earthing grid system and also providing of earth test termination block point near on wall/floor for checking/testing of earthing value system including fixing/laying 25mm bore GI pipe light grade with making funnel with wire mesh system for watering and also filling/laying adequate quantity of charcoal

Item No. 145.00 contd.... dust 200kg & common salt 200kg, chemical compound of magnicium sulphate (MgSo4) 200Kg and crystallin conductive compound 100kg shall be used for earthing system in alternative layers 100mm thick and at least 150mm around and bottom edge/surrounding of earth plate and also filling/laying of 500mm in layer of magnicium sulphate (MgSo4) from top edge of earth plate. In case area where soil condition is found bad, good earth i.e.black cotton soil or moistures normal soil is to be arranged to fill the excavated pit by mixing the arranged soil with back fill compound 25 Kg (BFC) 4 bags condutolite BFC for installation of earth electrode and also making necessary excavation and earth work for earthing pit in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded of stone aggregate XPM (weight not less than 4 Kg/Sqm) and connecting to earth test point complete all as specified and directed. Notes :- (i) The quoted rate shall deemed to be included for earth strip & protection pipe upto 7.5 mtr length and extra length if any shall be measured and paid separately under relevant items. (ii) After completion of work the earth on testing result desired value resistance should be less than 2.0 Ohm, if the desired resitance is not obtained, the erathing will be redone at no extra cost to the Govt. During the earthing, earth work if any bottom surface water seepage found at pit area site, the for dewatering through pump set shall deemed to be included in quoted rates. Nothing extra shall be admissible on this account to the Contractor.

Supply, fixing and laying earth continuity conductor or main earthing copper strip of size 32mmx6mm fixed to wall/floor/chases or buried in ground in any position or drawn through in any other situation and duly fixed it laying it uponsuitable size/type of porcelain insulator system or duly laying/drawn inside of suitable size/type of piping system with the help of MS clamp with nut, bolt for prevent unwanted contact of other medium to earth strip (type of laying/fixing copper strip on wall/roof/floor area shall be decided by Engr-in-charge) complete all as specified and as directed.

Supply, fixing and laying earth continuity conductor or main earthing copper strip of size 20mmx3mm fixed to wall/floor/chases or buried in ground in any position or drawn through in any other situation and duly fixed it laying it uponsuitable size/type of porcelain insulator system or duly laying/drawn inside of suitable size/type of PVC conduit /HDPE piping system with the help of saddles and fixing screws or MS clamp with nut, bolt for prevent unwanted contact of other medium to earth strip (type of laying/fixing copper strip on wall/roof/floor area shall be decided by Engr-in-charge) complete all as specified and as directed.

Supply, fixing and laying GI pipe 40mm bore light grade with all fitting laid in trenches/ under road /floor/ pole/ wall for protection of cable/strip including providing MS clamp for holding of pipe on pole/wall in proper size of clamps, nut bolt and washer etc complete all as specified and directed.

S&F electronic meters temper proof LCD display with polycarbonate cover, three phase, 415 V, 10- 60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54 with parameters to show data, time, current reading, load, PF, voltage and KWH including taking down existing old electric meter any type and deposited in AGE E/M store yard compete all as specified and directed.

S&F in repair double door VTPN distribution board 8 way with IP-43 1K-09 protection system and having mounting chanel and connection bus bar system suitable for MCCB as incommer and MCB as outgoing 415 Volts 3 phase 50 C/s power supply complete with appropriate size copper bus bar and neutral earth link alongwith providing of 01No MCCB 200 Amps rating with rupturing cap 36KA, 4 pole 415 Volts and also 12 Nos of MCB 3 Pole 20 Amps 'C' Curve of the same make as of distribution board and making all necessary electrical connection and dully fixed surface on wall or concealed on wall with the help of cutting chases to wall for fixing of DB and making good the disturbed wall surface complete all as specified and directed. Make:Havells cat pt No. DHDLVDRWAOFO08 or equivalent of make and model of Legrand / Schnider/Indoasian

S&F Sub main wiring system with Four runs PVC insulated FRLS wire, 1100 volt grade with multistranded copper conductor wire of size 4x10Sqmm and two run of 2x6 Sqmm (Nominal area) as in earth wire any type any length drawn through in heavy duty ISI marked concealed PVC conduit of suitable size along with its all fittings and connected accessories and duly fixed concealed on wall or surface on wall including taking down old unservicable sub main wiring system and making good all disturbed surfaces match to the existing surface complete all as specified and directed. Note:- 4 runs of 10sqmm and 2 runs of 6sqmm wire and one run of PVC conduit shall be measured and 1.0 RM.

Excavation in trenches/ under road/ PCC path/hard standing not exc. 1.5 m wide and n. exc. 1.5m depth for laying of pipe / cable in any type of soil and getting out etc complete all as specified and directed.

M&L for Sand cushioning for under ground cable provided with a layers of sand before laying cable and sand after laying and stretching the cable complete all as specified and directed.

M&L for brick covering width equal to length of brick for mechanical protection to cable with well burnt sub class 'B' bricks laid dry flat acomplete all as specified and directed.

Supply, fixing and laying GI pipe 50mm bore light grade for cable protection passing through under road, floor fixed to pole/ wall complete all as specified and directed.

Supplying and laying 1100 volts grade XLPE insulated, armoured heavy duty, electric cable cross sectional area 50sqmm 3.5 core, aluminium conductor and making electric connection including taking down of old cable complete all as specified and directed.

M/S Tajamul Ah Buchh

M/S AIJAZ ENTERPRISES