PROVIDING FIXING AND LAYING NEW PVC PIPE MACHINERY REPAIR OF PUMP CHAMBER AT RAJPURA BLOCK SUJANPUR DISTT PATHANKOT UNDER KANDI AREA DEVELOPMENT SCHEME PM 21

Amount

PUMPING MACHINERY Providing & Installing Testing & Commissioning of one No. Electrically driven Submersible Pumping set of reputed make capable of delivering 850 LPM against a head of 110 mtr along-with electric panel board consisting of electric appliance such as automatic Starter, Main Switch. Volt Meter, Ampere Meter, ELCB, Shunt Capacitor, Single Phase Preventer, Indicating Lamps, MVB/MCCBs etc. including G.I Column Pipe of suitable size 50 m (in 3 m Lengths each with flanges, screwed and welded on both sides) rubber gaskets, nuts and bolts submersible cable (of reputed make) complete in all respects. As per ISI 1239-2004

Rate of Motor with Pump

Panel Board

Submersible cable Size 10.00mm2

Column Pipe (G.I) 100 mm i/d

Sluice Valve Providing & fixing C.I D/F Sluice Valves ISI marked 14846-2000, including cost of tail piece, rubber joint, gland dori, Nuts, bolts & accessories, complete in all respects

Construction of brick masonry sluice valve chamber size 0.90m x 0.90m complete in all respect.

Providing, Fixing, laying, jointing, cutting & testing of uPVC Pipes & Specials (6 kg./cm2) including cost of excavation complete in all respects. Excavation with Manually

uPVC Pipe 63 mm o/d

Making Connection with existing pipe line including cutting cost of D-Joint, labour for fixing specials excavation including bailing out etc

Repair of Pump Chamber

Terracing consisting of tiles 22.86cm× 11.43cum ×3.83cm laid over25mm mud plaster, 7.5 cm mud filling on another layer of 25mm mud plaster including two coats of bitumen laid hot @ 1.65Kg. Per Sqm on top of RCC slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing etc.

Conglomerate floor 50mm thick cement concrete rate 1:2:4 on 100mm thick cement concrete 1:8:16 with stone aggregate 40mm guage and 100mm fine sand filling using mechanical mixer for mixing material.

Hollock shutter including hinges, screws, chocks, cheats, stops cords etc. complete fixed in position. panelled, glazed or glazed and panelled.

Hollock wood cup board shutter with plywood panels or faced on both side fixed in position (excluding the cost of handles, bolts hasp with staple but including the labour for fixing them) 30mm thick cup board

Kiln seasonal Hollock wood cup board chowkats including iron hold fasts, iron hinges corner straps, wooden knobs or handles fixed in position (Size 45 x 60mm). 30mm thick cup board

Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade.

Applying priming coat with methal primer on new steel or iron work incluing preparation of surface.

Supply & fixing of pressed steel frames (chowkats) consisting of 18 gauge (1.25mm thick steel sheet of the specified section (standard design latest) including iron lugs (hold fasts) for iron hings conforming to PWD specification including bolts for fixing stops lock, notch bolts, hydraulic spring and finished with one priming coat of approved quality fixed in position including cost of cement concrete 1:3:6 for filling in the frame and cement concrete for 1:2:4 for lugs complete.

Doors and Windows frame of Size 118mm×60mm with 40mm wide single rebate weighing 3.43 kg per meter.

Wrought iron & Mild steel ladders, framed grills, gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position

Cement Cencrete 1:2:4 gola 10cm×10cm concave quardrant along junction of roof with parapet wall finished smooth where specially specified

White washing 3 coats inside of pump chamber,

Finishing wall with cement based water soluble exterior paint such even shade.

Providing and fixing of Glass strips 4mm thick in floors

50mm wide

40mm wide

Preparation of Ball putty plastered surfaces for distempering including surface, applying filling with approved quality filler consisting of plaster of Paris and chalk mitti including finishing the surface to the required finish complete. Inside pump Chamber

Distempering with dry distemper of approved manufacture two or more coats over one priming coat to give an even shade.

Supplying & fixing glass panes with glazing clips and special metal sash putty of approved make.

Glass panes 4mm or 10.75 kg / sqm exceeding 0.4 sqm area

RECESSED HGW CONDUIT PIPE WIRING SYSTEM WITH FLUSH PIANO TYPE SWITCHES:

Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for having (Flush/ Piano type accessories) Step type electronic fan regulators 100watts (socket size), bell push, 5Pin 6Amp. sockets (4Module Box), 16/20Amp. universal sockets (6Module Box), 6/16/20Amp. Switches etc. and covered with brown bakelite white glazed translucent backside painted sheet 3mm thick etc., PVC connector (For Fan Box and Call Bell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½" deep for walls and CI 3" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):-

Wiring fan point without fan box

Wiring light point

Wiring 6 Amp. Plug control comprising wall socket point.

Wiring 16/20 amp. power plug control point.

Providing and fixing of ceiling fan of reputed make such as Crompton or equivalent

Providing and fixing of electric tube set of reputed make

Construction of gravel pit inside the Pump Chamber complete

Development of Water Works Providing & fixing 1.2mtr high fencing around the head works site with 1.65 meter post, placed every 2.5 meters apart, embedded in cement concrete blocks and every tenth post to be strutted with three rows of G.I. Barbed wire weighing 9.34 Kg per 100 meters (minimum) and fixing with GI staples tied to 6mm bar nib, with binding wire or by providing cut, including drilling holes in the post, including cost of posts, winding wire, strutted earth work in the post & aluminum painting complete in all respects as per DWSS standard Drawing and analysis.

Providing & fixing D-Hook complete with MS Bolts size 300mm x 18mm as per DWSS standard