Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Infra Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹57.8 LAccepted-AOC | L1 | Accepted-AOC Being L1 | |
| 2 | L2₹59.8 L+₹47,924 (0.81%)Rejected-Finance | L2 | Rejected-Finance Not being L1 | |
| 3 | Rejected-Technical | - | Rejected-Technical Firm is two class below. Firm not admited due to firm not have appropriate class ie C |
Tender Value
₹58.7 L
EMD Value
₹1.1 L
Closing Date
1 Jan 2024, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
CWE, HQ 133 WORKS ENGRS
HQ 133 WORKS ENGRS
SPL REPAIR TO QTR NO-09 TO 24 OF OR MD ACCN BLDG NO P 787 AT ATAL ENCLAVE AT BB CANTT SRINAGAR UNDER GE 864 EWS
2023_MES_629177_1
CWEK-48/2023-24
Open Tender
Civil Works
Item Rate
270 days
GE 864 EWS
Class C Category a i and b i
6 documents required · 6 mandatory
₹1,000
GE 864 EWS
₹1.1 L
Yes
HQ 133 WORKS ENGRS
2 Feb 2024
21 Nov 2023
9 Jan 2024
21 Nov 2023
1 Jan 2024
13 Dec 2023
21 Nov 2023 - 2 Dec 2023
3 Dec 2023
Amount
Dismantling plain or corrugated mild steel sheeting any gauge, thickness, including Nanital or similar pattern roof covering, complete all as specified and directed by Engr-in-Charge.
Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness (below or above ground level) and removal the rubbish/ demolished material outside defence land, complete all as specified and directed by Engr-in-Charge.
Demolition of brick work or stone masonary, precast cement concrete walling built in cement mortar including all quoins, arches, pillars etc., complete all as specified and directed by Engr-in-Charge.
Demolition of cement concrete (reinforced) in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas, and similar suspended work and removing rubbish/ demolished material outside defence land, complete all as specified and directed by Engr-in-Charge.
Dismantling of boarding, any description, fixed in any position with nails, complete all as specified and directed by Engr-in-Charge.
Dismantling timber scantling 40 Sq. cm and over in section, in any position of unframed/ framed work complete all as specified and directed by Engr-in-Charge.
Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs any thickness, including cover fillets complete all as specified and directed by Engr-in-Charge.
Dismantling of cast iron or reinforced concrtee drain pipes of dia 100/150mm , jointed in cement mortar and taking out of trenches/wall surface includig fittings, if required complete all as specified and directed by Engr-in-Charge.
Dismantling timber scantlings in any position in fillets, rails, posts, rafters , purlins, etc. under 40 sq. cm in section (Unframed work) complete all as specified and directed by Engr-in-Charge.
Taking down cement plaster of any description, thickness and in any position including raking out joints, hacking for key, scrubbing down with water etc , and removal the rubbish/ demolished material outside defence land, complete all as specified and directed by Engr-in-Charge.
M&L for hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed by Engr-in-Charge.
M&L for dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish/ demolished material outside defence land, complete all as specified and directed by Engr-in-Charge.
Taking down chowkats or frames with shutter area exceeding 1.50 Sqm and not exc 4.00 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish , complete all as specified and directed by Engr-in-Charge.
Taking down chowkats or frames with shutter area not exceeding 1.50 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and directed by Engr-in-Charge.
Taking down shutters of any description exc. 1.00 sq. m but not exc. 2.00 sq. m each and refixing in the same opening after resecuring or easing and adjusting complete all as specified and directed by Engr-in-Charge.
Taking down shutters of any description exceeding 1.00 Sqm but n.exc 2.00 Sqm each from chowkhat and removing to store complete all as specified and directed by Engr-in-Charge.
Demolition of Stone slabs and tiles of any description or thickness in floors , aprons etc. laid, bedded and pointed in any mortar, complete all as specified and directed by Engr-in-Charge.
M&L for brick work with subclass ‘B` old size bricks, straight or curved on plan excg 6 metre mean radius built in cement mortar (1:6), complete all as specified and directed by Engr-in-Charge.
M&L for cutting holes into exc. half brick but n. exc one brick thick walls, in stone walls built in cement mortar or in cement lime mortar, for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B1 as required (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall) complete all as specified and directed by Engr-in-Charge.
M&L for providing Precast reinforced Cement Concrete 1:2:4 type B1 using 20mm graded aggregate as in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.
M&L for providing cement concrete 1:2:4 Type B1 using 20mm graded aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed by Engr-in-Charge.
M&L for Rendering 15mm thick on fair faces of brick work or concrete surface in cm (1:4) to be finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.
M&L for 15mm thick rendering in cement mortar (1:6) on surface of any description of brick or concrete and finished the surface even and fair without using extra cement complete all as specified and directed by Engr-in-Charge.
M&L for 15mm thick rendering in on fair faces of brick work or concrete surfaces in cement mortar 1:4 mixed with WPC @2% by weight of cement or as per manufacturer’s instructions, finished even and fair, complete all as specified and as directed. (Note : WPC shall be measured and paid separately) complete all as specified and directed by Engr-in-Charge.
Supply only integral water proofing compound, complete all as specified and directed by Engr-in-Charge.
M&L for 5mm thick cement plaster in CM (1:3) to ceiling surface and finished the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.
M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkaline primer with ith hand roller, complete all as specified and directed by Engr-in-Charge.
Material and labour for two coat of cement base paint over a coat of alkaline resistant primer on newly plastered surface including preparation of surface of wall complete all as specified and directed by Engr-in-Charge.
M&L for preparation of newly plastered ceilng surfaces and applying two coats of oil bound distember over one coat of primer complete all as specified and directed by Engr-in-Charge.
M&L for one coats of cement base paint to old plastered wall surfaces incl preparation of surfaces complete all as specified and directed by Engr-in-Charge.
M&L for old treated surfaces (Plastered or un-plastered) of wall, etc. and applying one coat of oil bound distemper with hand roller complete all as specified and directed by Engr-in-Charge.
M&L for preparation of old plastered ceilng surfaces and applying one of oil bound distember complete all as specified and directed by Engr-in-Charge.
M&L for 2nd class hardwood clean sawn in scantlings, in any position in framed/unframed work, complete all as specified and directed by Engr-in-Charge.
S&F mild steel framed work as in door chowkats, gate of angle or other section of grade Fe-290-Gde E-165 with gusset plate rails, braces etc welded/drilled to fixing of steel sheeting or other covering doors etc. to be prepared for sliding or hanging with and including either hooks and hinges or steel hanging door fittings (exclusive steel sheeting or other covering, running rails & guides) and hanging also fastening and fixing complete all as specified and directed by Engr-in-Charge.
S&F for 2nd class hard wood plain, solid straight chowkats and frames, wrought framed rebated on the solid, rounded or chamfered put together with glue pinned at joints, complete all as specified and directed by Engr-in-Charge.
S&F IInd class hardwood factory made 35mm thick gauged skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed by Engr-in-Charge.
S&F for factory made 35mm thick, 2nd class HW, plain framed, panelled shutters (two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed by Engr-in-Charge.
S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, with all fitting and fixtures complete all as specified and directed by Engr-in-Charge.
Supply and fixing factory made PVC solid door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of extended 5 mm rigid PVC foam sheet , reinforced with steel square tube , complete all as specified and directed by Engr-in-Charge.
Supply and fixing for aluminium alloy anodized (powder-coated) window frame with double leaf and double shutter (both gauged and glazed shutter in same frame ) open able type, with aluminium sections as per of “Jindal” section numbers for casement windows with double shutters including aluminium alloy anodized snap type beads, handles, aluminium anodized barrel tower bolts and glazing clip, joint cleats, rubber gaskets etc., complete all as specified and directed by Engr-in-Charge. for series-B “ Jindal” section numbers for casement (a)Frame of section 101.6mmx44.45mmx2.10mm thick and section for shutter 47.62x44.45x1.95 mm thick (b) Mullion 53mmx52mmx 2mm thick not less than 1.065 kg/mtr. (c) Glazing clip weighing 0.259kg/mtr. (d) Windows shall be provided with 02 Nos. of tower bolt for single leaf and 03 Nos. of tower bolts for double leaf. Tower bolts shall be aluminium alloy anodized weighing 0.302kg/mtr. Handles shall be aluminium anodized ‘D’ type handle of size 98mm and thickness 2.37mm weighing 0.875kg/mtr and one no per each open able leaf shall be provided. (Note : 1. The rates shall be inclusive of provision of and fixing of rubber packing/gasket. Glass pane and wire gauge shall be measured and paid for separately. Manufacturers : M/S Indian Aluminium Co. Ltd., UCO Bldg, New Delhi. M/S Jindal Aluminium Pvt. Ltd. M/S Hindalco Pvt. Ltd. or any other equivalent approved by GE.
Supply and fixing aluminium powder coated section, as in partition and frame for door, window, ventilators of standard section and thickness as directed , cut and jointed together with cadium plated steel screws, plugs for fixing screws, etc. complete all as specified and directed by Engr-in-Charge. Note-(i) Fixing of shutter with frame shall be as per manufacturers instructions and fitting shall be paid under this item.(ii) Aluminium section shall be of Make “Jindal/Hindalco / Indalco”. (iii) Thickness of powder coating shall not be less than 50 micron. (iv) Frame shall be one or more rebate as per requirement at site.
S&F aluminium anodized grill 5.5mm thick weight not less than 2.5kg per square (in the shape of expanded metal aluminium xpm jalli) opening size length of expansion (60mm) and width expansion 45mm fixed in aluminium anodized window with ‘F’ channel of handle section with screw, complete all as specified and directed by Engr-in-Charge.
S&F for sheet glass 3.00mm thick, ordinary quality and glazing with oil puitty, in square not exc 0.5 sqm in each pane complete all as specified and directed by Engr-in-Charge.
S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staple or fixing with beads to wooden joinery when fixed in panels of joinery, complete all as specified and directed by Engr-in-Charge.
S&F in repair, stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staple or fixing with beads to wooden joinery when fixed in panels of joinery, complete all as specified and directed by Engr-in-Charge.
S&F 300mm long mild steel ordinary rat tail rod pattern springs inclduing roller and roller plate complete all as specified and directed by Engr-in-Charge.
S&F aluminum anodized, barrel tower bolt of extruded section 200mm long, ISI marked, complete all as specified and directed by Engr-in-Charge.
S&F 150 mm long, extruded aluminium alloy handle, fabricated type, complete all as specified and directed by Engr-in-Charge.
S&F 75mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and directed by Engr-in-Charge.
S&F 100mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and directed by Engr-in-Charge.
S&F 300 mm aluminum anodised sliding door bolt, ISI marked, with hasp, staple (bolt type) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt of extruded section or cast aluminum alloy, complete all as specified and directed by Engr-in-Charge.
S&F mild steel 25mm dia, 1.6mm thick, PVC coated, fancy type, heavy duty drapery rod incl pair of bracket,finials (latto) at ends including fixing on wall with screws, fixed in repair, complete all as specified and directed by Engr-in-Charge.
M&L TMT steel bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engr-in-Charge.
S&F mild steel works in bands, straps, supports, stays, bolts, hooks, hold fasts etc, similar articles conforming to Fe-290.Gde-E-165, complete all as specified and directed by Engr-in-Charge.
S&F roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc fixed in position,conforming to Fe-410(Gde 250), complete all as specified and directed by Engr-in-Charge.
S&F for 0.63mm Galvanised, Corrugated Mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts and washers, ISI marked,, in roofs, walls etc. with grade of zink coating 275, complete all as specified and directed by Engr-in-Charge.
S&F 0.63 mm thick Plain, galvanized mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) of class-2, ISI Marked, complete all as specified and directed by Engr-in-Charge.
Supply and fixing Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. Hangers 6mm dia . GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I flat 40X3mm size 60mm long complete all as specified and directed by Engr-in-Charge.
Supply and fixing 12mm thick Gypsum board ceiling fixed with screw to Gl frame work as per manufacturers instructions complete all as specified and directed by Engr-in-Charge.
S&F 25mm thick block boards, grade 2 quality, interiojr grade , commercial type, fixed with screws to timber frame work with 0.9mm thick decorative laminate type 1 of surface finish (colour and pattern as approved) complete all as specified and directed by Engr-in-Charge.
Material and labour for decorative moulding /beading 5mm thick and 25mm wide, of fancy type fixed to board/ply of any description complete all as specified and directed by Engr-in-Charge.
S&F for 75mm PVC (SWR) vent cowl complete all as specified and directed by Engr-in-Charge.
S&F for 110mm PVC (SWR) vent cowl complete all as specified and directed by Engr-in-Charge.
S&F 100mm long extruded aluminium alloy handles, fabricted type , anodised complete all as specified and directed by Engr-in-Charge.
M&L for 20mm thick boarding, hardwood IInd class, planed one side with butt joints chamfered one side fixed with nails in any situation (except flooring and skirting) fixed in repair complete all as specified and directed by Engr-in-Charge.
S&F 18/19mm thick block boards, grade I quality, exterior grade, fixed with nails and screw to timer frame work in shelves of built in cup board, partition, pelmet box and similar work complete all as specified and directed by Engr-in-Charge.
M&L for Second class hardwood plain fillets, square, rectangular or triangular in section of area exceeding 6 Sq. cm and not exceeding 13 Sq. cm, clean sawn, secured with nails or brads, complete all as specified and directed by Engr-in-Charge.
Material and labour for premium quality, joint free, non skid coloured ceramic tiles (Square/rectangular) , area of each tiles exceeding 0.18 sqm and not exceeding 0.38 sqm and 8 to 10 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed in white or coloured cement to match the surface over and including cement screed bed 15mm thick in cement mortar (1:6), complete all as specified and directed by Engr-in-Charge.
M&L non-skid ceramic tiles 7 to 8mm thick (square) area of each tile exdc 0.18 sqm but n.exc 0.38 sqm in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to matcjh with tile laid over and including screed plaster 10mm thick in CM(1:3) complete all as specified and directed by Engr-in-Charge.
Material and labour for premium quality, joint free, non skid coloured ceramic tiles (Square/rectangular) , area of each tiles exceeding 0.11 sqm and not exceeding 0.18 sqm and 6 to 7 mm thick as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including cement screed bed 50mm thick in cement mortar (1:6) , complete all as specified and directed by Engr-in-Charge.
M&L glazed ceramic ceramic coloured tiles, joint free 350x450x7mm thick for work on vertical surfaces such as skirting, dado, set & jointed in cement slurry and pointed in coloured cement to match over 10mm thick plastring in CM(1:3) complete all as specified and directed by Engr-in-Charge.
M&L18mm thick granite (of any type) work (table rubbed and polished and moulding) in platforms, steps, jambs, pillar, counter WHB, floor over and including 20mm thick in cement mortar (1:6) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite, complete all as specified and directed by Engr-in-Charge.
S&F chequered cement concrete tiles with grey cement and pigment , rubber moulded with laquer polish for extra shine, size 300 mm x 300 mm x 22-25 mm thick, ISI marked, coloured, set jointed and pointed in neat cement slurry over and including 20 mm thick (average thickness) cement screed (1:6) base, complete all as specified and directed by Engr-in-Charge
M&L for machine cut, pre polished (Granite finish) kota stone flooring 20-25 mm thick in steps in single piece (without any joint) set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed with grey cement over and including cement screed bed 20mm thick in cement mortar (1:6) base , complete all as specified and directed by Engr-in-Charge. Note- All exposed surface shall be round/bull nosed to aminimum radius of 5mm and two parallel grooves ten by ten( 10mm x 10mm ) immeadiately behind the noising shall be provided and cost of the same is included in the rates quoted by the contractor.
M&L for machine cut, pre polished (Granite finish) kota stone slab 20-25mm thick on vertical surface riser, pillar, skirting, etc. .set, jointed & pointed with grey cement slurry over and including 10mm thick plaster in cement mortar (1:4) on brick work or concrete surfaces complete all as specified and directed by Engr-in-Charge.
Taking up or down steel tubing and connections for 15mm dia including cleaning for refixing or removal to store complete all as specified and directed by Engr-in-Charge.
Taking up or down steel tubing and connections for 20mm dia including cleaning for refixing or removal to store complete all as specified and directed by Engr-in-Charge.
S&F 15mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed by Engr-in-Charge.
S&F 20mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed by Engr-in-Charge.
M&L for two coats of synthetic enamel paint on steel surfaces over a coat of red oxide primer including preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth, complete all as specified and directed by Engr-in-Charge.
S&F 10 litre capacity, low level, virgin polypropylene cistern, ISI marked, coloured complete with PVC bend/flush pipe and making all connection including taking down existing high or low level unerviceable flushing cistern and making good the disturbed surface to match with the existing surface complete all as specified and directed by Engr-in-Charge.
Supply and fixing vitreous china wash hand basin white flat back of size 550x400mm with padestal including CI brackets embedded in wall in CM 1:4, PVC waste pipe, PVC connections and chromium plated waste coupling, etc fixed in repair complete all as specified and directed by Engr-in-Charge.
S&F vitreous China squatting pan of Orissa pattern size 580mmx440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and integral foot rests of any pattern complete including lime concrete, making good to disturbed surface of sub base and flooring with the existing surface and connection to flush pipe fixed in repair complete all as specified and directed by Engr-in-Charge.
S&F shower rose chromium plated of 125mm size with swivel joints incvl, fixing to steel puipe or union of 15mm bore fixed in repairscomplete all as specified and directed by Engr-in-Charge.
S&F bib tap screwed down high pressure, cast copper alloy,fancy type, chromium plated, ISI marked, with capstan heads, screwed down suitable for 15mm bore pipe or union fixed in repair, complete all as specified and directed by Engr-in-Charge.
S&F in repair, angle cock, 15mm dia chromium plated, cast copper alloy, fancy type, ISI marked, screwed down, high pressure with capstan head, screwed both ends for iron pipes or for unions fixed in repair complete all as specified and directed by Engr-in-Charge.
S&F brass tubular towel rail (finish Glossy), 20mm dia, D type, 60cm long between flanges fixed in repair, complete all as specified and directed by Engr-in-Charge.
S/F in repairs for Corner Glass shelf 300 x 300 mm (Big) , 225 x 225 mm (medium) & 150 x 150 mm (small) three set, complete all as specified and directed by Engr-in-Charge.
S&F in repairs 5.5mm thick glass shelf assembly consisting of glass shelf, 60cm long and 12 cm wide with CP bracket and guard railing fixed in repair complete all as specified and directed by Engr-in-Charge.
S&F PVC connections 450 mm long and 15mm dia with PTMT nuts and PVC washers on both ends, complete all as specified and directed by Engr-in-Charge.
S&F PVC connections 600 mm long and 15mm dia with PTMT nuts and PVC washers on both ends, complete all as specified and directed by Engr-in-Charge.
S&F water storage tank 500 ltr capacity HDPE triple layer, white coloured, conforming to IS , fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, PVC valve 20 mm high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore,including taking down the unserviceable water tank and removing from site, complete all as specified and directed by Engr-in-Charge.
S&F stainless steel sink 1.00mm thick, ISI marked for kitchen with plug, waste PVC pipe, washers including cantilever cast iron brackets connecting union waste pipe of overaqll size 495 mm x 420mm with bowl size 410 mm x 330mm x 160 mm etc fixed in repair including PTMT wste coupling of 32mm bore complete all as specified and directed by Engr-in-Charge.
S&F Sink mixer, chromium plated, fancy type with capstan head handle, screwed down high pressure with lettered hot and cold including CP brass flange and necessary extension nipple screwed for 15 mm dia pipe fixed in repair complete all as specified and directed by Engr-in-Charge.
S&F in repair wall mixer, chromium plated, fancy type with capstan head handle, screwed down high pressure with lettered hot and cold screwed for 15 mm dia pipe fixed in repair complete all as specified and directed by Engr-in-Charge.
S&F in repair brass chromium plated, hot and cold central hole, mixer for mixing hot and cold water, fancy type with capstan head handle, screwed down high for 15mm bore pipe or union fixed in repair, complete all as specified and directed by Engr-in-Charge.
M&L for lagging to 20mm dia pipes used in internal water supply or plumbing all round with 25mm thick bonded mineral wool pre-formed `SNAP ON` pipe sections of density 144 Kg/cum conforming to IS 9842 complete all as specified and directed by Engr-in-Charge.
M&L for lagging to 15mm dia pipes used in internal water supply or plumbing all round with 25mm thick bonded mineral wool pre-formed `SNAP ON` pipe sections of density 144 Kg/cum conforming to IS 9842 complete all as specified and directed by Engr-in-Charge.
S&F in repair stainless steel plate rack 1mm thick of size 600 x 900 x 250 mm with stainless steel screw to wall complete all as specified and directed by Engr-in-Charge.
Material and labour for 25mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as levelling course, finished even and fair to receive floor finishes, complete all as specified and directed by Engr-in-Charge.
M&L 75mm thick PCC 1:3:6 type C-1, as in plinth protection, laid in panels of area not exceeding 2.00 sqm with 6mm wide joints filled with mastic (using bitumen and sand mixture applied hot in the ratio of 1:3 by weight) formed at the end of each panel and change in direction of plinth protection/PCC Path and paving and finishing the top surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.
M&L for hardwood IInd class hard wood weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified and directed by Engr-in-Charge.
S&F cast iron soil, waste and vent spun pipes 100 mm bore, ISI marked, in any length, with or without ears, with cement joints, laid in trenches complete all as specified and directed by Engr-in-Charge.
S&F cast iron soil, waste and vent spun pipes 100 mm bore, ISI marked, in any length, with or without ears, with cement joints,fixed to walls complete all as specified and directed by Engr-in-Charge.
Supply and fixing cast iron soil, waste and vent spun pipes 75 mm bore, ISI marked, in any length, with or without ears, with cement joints, laid in trenches/floor complete all as specified and directed by Engr-in-Charge.
S&F cast iron soil, waste and vent spun pipes 75 mm bore, in any length, with or without ears, with cement joints,fixed to walls complete all as specified and directed by Engr-in-Charge.
S&F in repair cast iron bends (any radius) 100 mm dia diminishing pieces or tapers complete all as specified and directed by Engr-in-Charge.
S&F in repair cast iron bends (any radius) 75 mm dia diminishing pieces or tapers complete all as specified and directed by Engr-in-Charge.
S&F in repair, cast iron branch pieces, 100 mm dia, single (equal or unequal), ordinary or inverted or with parallel branches complete all as specified and directed by Engr-in-Charge.
S&F in repair, cast iron branch pieces, 75 mm dia, single (equal or unequal), ordinary or inverted or with parallel branches complete all as specified and directed by Engr-in-Charge.
S&F 110mm dia PVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in trenches or in floors, complete all as specified and directed by Engr-in-Charge.
S&F 75mm dia UPVC soil, waste, drain pipe, type ‘B’, conforming to IS 13592-1992, single socketed, in any length, with rubber rings joints or jointed with solvent cement, laid in trenches or in floor complete all as specified and directed by Engr-in-Charge.
S&F stack clamps made out of 50mm x 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore pipe complete all as specified and directed by Engr-in-Charge.
Supply and fixing stack clamps made out of 50mm x 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore pipe complete all as specified and directed by Engr-in-Charge.
M&L for prepaaration of new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engr-in-Charge.
M&L for taking down carefully existing old burnt out / unserviceable aluminium / copper point wiring system any type/ size any description complete for light, fan, socket or power points etc including along with all type of fittings & fixture and it connected fixing acessories such as switches, sockets, ceiling roses, holder , regulators, etc and removing the old materials from the site for taking as a schedule of credit complete all as specified and directed by Engr-in-Charge.
M&L for making point wiring system with single runs of PVC insulated FRLS wire , 1100 volt grade with multistranded copper conductor wire of size 1.5 Sq.mm (Nominal area) (ISI Marked) any type any length drawn through in heavy duty ISI mark and including wiring system dully fixed concealed in wall / surface on wall complete all as per directed by EIC including providing of PVC conduit of 20 mm dia size / PVC Casing capping of suitable size along with its all connected fittings accessories including providing of pressed steel terminal sunken boxes 1.6 mm thick & duly fixed concealed in wall / surface on wall and top covered with electro plated 3 mm thick plastic laminated sheet for housing/mounting of switches sockets, regulators etc and also using /drawind of 1.5 sqmm PVC insulated FRLS wire , 1100 Volt grade (ISI Marked) with multistranded copper conductor wire used as a continuous earth wire which is connected with terminated the box to ceing rose / fitting complete and including making good to all disturbed surfaces of wall/ceiling and floor area of wiring system and to match the existing surface of wall/floor/ceiling etc. complete all as specified and directed by Engr-in-Charge.
Description complete all as per above sr item No 118 but one light point / fan point controlled by one switch of one way point wiring system complete all as specified and directed by Engr-in-Charge.
Description complete all as per above Sr item No 118 but one 3/5 pin type 5 Amp socket outlet point fixed on same board and controlled by one switch of one way point wiring system complete all as specified and directed by Engr-in-Charge.
Description of all as per above Sr item No 118 but one 3/5 pin type 5 Amp socket outlet point fixed on independent board and controlled by one switch of one way point wiring system complete all as specified and directed by Engr-in-Charge.
Description of all as per above Sr item No 118 but one bell point fixed on board and controlled by one switch of one way point wiring system complete all as specified and directed by Engr-in-Charge.
Description of all as per above Sr item No 118 but using single runs of PVC insulated FRLS wire ,1100 volt grade with multistranded copper conductor wire of size 2.5 Sq. mm (Nominal area) (ISI Marked) for 3/6 pin type15 Amp socket outlet point wiring system with controlled by one way switch fixed on independent board and also providing of 2.5 sqmm PVC insulated FRLS wire , 1100 Volt grade (ISI Marked) with multistranded copper conductor wire used as continuous earth wire complete all as specified and directed by Engr-in-Charge.
Supply and fixing switch paino 5/6 Amps 230 Volts , complete for one way switching system. complete all as specified and directed by Engr-in-Charge.
Supply and fixing 5/6 Amps socket AC 230 Volts 3/5 pin type complete all as specified and directed by Engr-in-Charge.
Supply and fixing switch paino 15/16 Amps 230 Volts ,complete for one way switching system. complete all as specified and directed by Engr-in-Charge.
Supply and fixing socket 15/16 Amps AC 230 Volts 5/6 pin type complete all as specified and directed by Engr-in-Charge.
Supply and fixing bell push switch 5/6 Amps 230 Volts , complete for one way switching system. complete all as specified and directed by Engr-in-Charge.
Supply and fixing fan regulator with hum free step type alongwith speed control know of capacity 120 watt 230 Volts , complete for one way switching system complete all as specified and directed by Engr-in-Charge.
Supply and fixing bell Ding Dong Type, AC 230 volt, Single Pole complete all as specified and directed by Engr-in-Charge.
Supply and fixing ceiling rose three terminals type made out of polycarbonate , isolated body complete all as specified and directed by Engr-in-Charge.
Supply and fixing of wall mounted slim batten type decorative integrated design LED tube light fitting of rating capacity in 1x 20W/22W with eletronic driver and fitting extruded body made of aluminum housing with high quality polycarbonate diffuser with long life energy saving and required fitting use in both warm/white type colour set complete set and also providing suitable type of flate fexible two/three core cable and making electric connection and including taking down of old fittingcomplete all as specified and directed by Engr-in-Charge.
Supply and fixing of flush type PVC insulated body batten / angular type lamp holder and having in side of holder with brass adhaptor anlongwith back plate all fixing accessoris including duly fitted with 7/9 watt of LED bulb complete all as specified and directed by Engr-in-Charge.
Supply and fixing in repair/replacement of double pole and neutral enclosure with two pin and earth pug and socket complete alongwith MCB SPN, 240 Volts, 20 Amps, 10 kA rupturing capacity, 'C' series complete all as specified and directed by Engr-in-Charge.
Supply & fixing of ventilating exhaust fan made out of sturdy high quality engineering plastic, complete with louvers,and shutter operational of size 250mm sweep suitable to work on 230 Volts 50 Hz, 1200 RPM, coper winding including making of suitable type /size of hole on wall complete all as specified and directed by Engr-in-Charge.
Supply and fixing of decorative profile wall mounted LED mirror light fitting 20 Watt 6500 K of size 57.5 CM long or 2 fit long with aluminium chanel environmental friendly energy efficient and long life energy saving and required fitting use in both warm/white type colour set all as per make of Havells & model -LHEXARP7IN1W020 or equivalent specification and model & make of Philips /Crompton complete set complete set and including providing of suitable type of flate fexible two/three core cable and makong electric connection and including taking down of old fitting complete all as specified and directed by Engr-in-Charge.
M& L for taking down carefully existing ceiling fan /exhaust fan/ geyser any type sweep and removing fan blade including cleaning all dust particles and filling cavities with filler material, oiling ,greasing including painting fan with blade/geyser complete one coat of synthetic enamel white paint by spraying and assemble the same along with all connecting fixing accessories like rubber rell, nut ,bolt ,washer,lock pin etc and hanging the same position with the help of nut bolt and washer etc along with all electrical wire connection complete complete all as specified and directed by Engr-in-Charge.
Supply and fixing of Sub main wiring system with two runs PVC insulated FRLS wire,1100 volt grade with multistranded copper conductor wire of size 2 Run of 6 Sqmm and 1 run of 6 Sqmm (Nominal area) (ISI Marked) any type any length and drawn through in heavy duty ISI mark PVC Casing capping / PVC conduit of suitable size along with its all fittings and connected accessories and duly fixed concealed on wall or surface on wall including taking down old unservicable sub main wiring system complete and making good all disturbed surfaces match to the existing surface complete all as specified and directed by Engr-in-Charge.
Supply and fixing of sheet metal enclosure duly powder coated with locking arrengment system and having double door TPN 4 way distribution board with IP-43 1K-09 protection system and having mounting chanel and connection bus bar system suitable for MCCB as incommer and MCB as outgoing 415 Volts 3 phase powe supply , complete with appropriate size copper bus bar and neutral and earth link confirming complete alongwith providing of 01No MCCB 160 Amps rating with rupturing cap 25 KA 3 pole 415 Volts and also 12 Nos of MCB SP 63 Amps 'C' Curve of the same make as of distribution board complete & including taking down of existing DBs with MCBs and making all necessary electrical connection and dully fixed surface on wall or concealed on wall with the help of cutting chases to wall for fixing of DB and making good the disturbed wall surfacecomplete all as specified and directed by Engr-in-Charge.
Supply and fixing of sheet metal enclosure duly powder coated with locking arrengment system and having double door SPN 8 awy distribution board with IP-43 protection system and having mounting chanel and connection bus bar system with having capacity 200 Amps and suitable size of common neutral link including taking down of existing DBs with MCBs and making all necessary electrical connection and dully fixed surface on wall or concealed on wall with the help of cutting chases to wall for fixing of DB and making good the disturbed wall surface complete all as specified and directed by Engr-in-Charge.
Supply and fixing of MCB SPN 40 to 63 Amps, 230 Volts, 50 Hz AC supply suitable for 'C' series, 10 KA breaking capacity complete all as specified and directed by Engr-in-Charge.
S&F MCB SP 06 to 32 Amps, 240 Volts, 50 Hz AC supply suitable for 'C' series, 10 KA breaking capacity complete all as specified and directed by Engr-in-Charge.
Supply and lay GI pipe 40 mm bore medium grade with all fitting laid in trenches/ under road /floor/ pole/ wall for protection of cable including providing clamping arrangment for holding of pipe on pole/wall in proper size of clamps, nut bolt ,and washer etc complete all as specified and directed by Engr-in-Charge.
Supply and lay GI pipe 50 mm bore medium grade with all fitting laid in trenches/ under road /floor/ pole/ wall for protection of cable including providing clamping arrangment for holding of pipe on pole/wall in proper size of clamps, nut bolt ,and washer etc complete all as specified and directed by Engr-in-Charge.
Supply , laying and testing of LT cable XLPE insulated screened,PVC bedded galvanized steel strip or wire armoured electric power cable ( heavy duty ) with aluminium conductor 1100 volt grade cross section area of size 25 sqmm 4 core including laid in trenches or fixing on poles or passing through pipes complete including taking out of old unserviceable cable any type any size complete all as directed by Engr-in-Charge.
M&L for excavation in trenches/ under road/ PCC path/hard standing not exc. 1.5 m wide and n. exc. 1.5m depth for laying of pipe / cable in any type of soft /loose soil and getting out etc complete all as specified and directed by Engr-in-Charge.
M&L for Sand cushioning for under ground cable provided with a layers of sand before laying cable and sand after laying and stretching the cablecomplete all as specified and directed by Engr-in-Charge.
M&L for brick covering width equal to length of brick for mechanical protection to cable with well burnt sub class 'B' bricks laid dry flat complete all as specified and directed by Engr-in-Charge.
M&L for returning filling in including, spreading, leveling and well ramming in layers not exceeds 25 cm thick in any type of soil complete all as specified and directed by Engr-in-Charge.
M&L for removing excavated material to a distance not exceed 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge.
Supply and fixing of environmental friendly LED street light fitting of rated capacity 45Watt out door type made out of pressure die cast hosing with glass and high performance polycarbonate optics with LEDs with drives and having IP 65/66 protection and surge to heat resistant sink for better heat dissipation and including to ready for use and required in both warm/white coluor type fixture complete set all including providing of suitable size of dia GI pipe light grade bracket and it to match/setting the new fitting fixture hole attechment system of suitable bracket length upto 1.2 mtr long and make to shape / bend of 120 degree angle including duly fixed alongwith existing pole /bldg wall/ roof with the help of 02 Nos of MS fixing clamp alongwith nut bolt and including providing of suitable type of flate fexible two/three core cable and makong electric connection and including taking down of old fitting complete all as specified and directed by Engr-in-Charge.
Material and labour for earthing complete with galvanised steel earth plate electrode 60cmX60cmX6.0mm thick, buried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of the plate not less than 1.5mtr below normal ground level connected to GI earth strip of size 32x6 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron complete earth pit of PCC M-10(Nominal mix) using 20mm graded stone aggregate, 50mm thick earth pit cover of RCC M-15 (Nominal mix) using 20mm graded stone aggregate with MS TMT reinforcement bar of 8mm dia @ 150mm centre to centre both ways, MS handle 10mm dia made to shape, GI funnel, wire mesh and 20mm bore GI water pipe light grade and 40mm bore light grade GI pipe for protection of earth strip from plate to main switch board, common salt, charcoal dust including testing on completion complete all as specified and as directed all as shown in electrical plate No. 3 including testing on completion and making good the disturbed surfaces of wall floors etc without claiming extra cost all as directed by Engr-in-Charge. (Note: GI strip & GI pipe beyond 7.5Mtr length from earth electrode shall be measured and paid separately) Completed all as specified and directed by Engr-in-Charge
M/S BASHIR AHMAD MIR
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .