SPL REPAIR OF BLDG NO H-3 (MT AREA) OF 7 MAATHA LI, PROVN OF POLYHOUSE (LENGTH 50 FT BREADTH 35 FT AND HEIGHT 16 FT) INTEGRATED WITH SPRINKLER SYSTEM ALONGWITH OVERHEAD WATER TANK 2000 LTRS ON IRON STAND IN 137 CETF LOC AND PROVN OF PAVED AREA

Taking down cement plaster on wall & ceiling including raking out joint, hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for 12mm thick ready to use cement based plaster (Ready mix plaster ) with high quality polymer additive and well graded sand and fillers over wall/ ceiling of brick, stone or concrete including preparing the surfaces clean and made free from dirt,oil grease,concrete sealer or curing compound using a wire brush of mopping. Dampen the surface with clean water. water to be mixed/ preparation of mortar to be done as per manufacturer instruction complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls applying a coat of 1mm thick wall care putty on wall including rubbing with sand paper to obtain a smooth surface and then applying two coats of exterior weather proof anti algae 100% acrylic emulsion over a coat of exterior water based primer complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying three coats of white wash complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F for Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for Providing, cement concrete Type B1 1:2:4 (20 mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed.

S&F in repair Mild steel 1.25mm thick plain black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as require complete all as specified and directed.

M&L for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts complete all as specified and directed.

Demolition of concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for cement concrete Type D2 (1:4:8) (using 40mm graded stone aggregate) as in foundations,filling and mass concrete complete all as specified and directed.

M&L for sand filling under floor or in foundation including watering and in consolidation complete all as speified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 & ISI Marked of 80 mm thickness M-40 Grade with grey cement and pigment (Red & yellow) complete all as specified and directed.

M&L for PCC 1:2:4 Type B-1 (using 20mm graded stone crushed aggregate) as in rounded or chamfered on edges in any description complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in path / plinth protection / sub base finished the surfaces even & fair complete all as specified and directed.

Dismantling of stone slab/brick tiles single layer on roof/ground floor,laid bedded and pointed in any mortar complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement Screed bed or bedding layer of mortar 15 mm thick in CM (1:6) for laying floor finishes laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 10mm thick rendering in CM (1:3) and jointed with all as per item No 20.00 above complete all as specified and directed.

Taking down chowkhat or frames with shutter (without taking off shutters from the frame) n exc 1.5 sqm including making good dismantled portion by brickwork,cement concrete (1:2:4) or CM(1:3) and plastering each complete all as specified and directed.

Taking down chowkhat or frames with shutter (without taking off shutters from the frame) exc 1.5 sqm n exc 4 sqm including making good dismantled portion by brickwork,cement concrete (1:2:4) or CM(1:3) and plastering each complete all as specified and directed.

M&L for taking down Steel Shutters or of any description exc 2 sqm each and refixing in the same opening after strengthning, straightening structural member of gate and proper welding the joints and adjusting complete all as specified and directed.

S&F Pre-Painted steel windows & ventilators with glazed & wiremesh shutter with Guard bars. the frame and shutter section should be cut to length and miter joined with corner brackets made of Polypropylene. Mullion section should be joined using nut and bolts. 4mm thick clear float glass to be provided using EPDM gasket all around glass incl all necessary accessories required complete all as specified and directed. Ref TD - CELZ/C-TD/102 sheet 1/1 and 1/2. Make : NCL Buildteck pvt ltd / TATA Pravesh / Elixir Met form Pvt Ltd / Ashish industries. Note : Net opening will be measured for payemnt purpose no extra payment will be made for glass or wiremesh.

Mild steel framed work such as in doors/chowkhats or gates of angle or other section with gusset plates, rail, braces etc. complete drilled for fixing of steel sheeting or other covering. Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening & fixing and similar work conforming to Fe-290 grade E-165 complete all as specified, making good disturbed portion to match existing surface complete all as specified and directed.

M&L for preparation of new surfaces of wood and wood based materials of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat pink primer complete all as specified and directed.

S&F flush shutter 35 mm thick solid core construction with block board core and plywood face panels commercial type on both sides with lipping / frame to match complete all as specified and directed.

S&F 200mm stainless steel fancy handle of approved make fixed with SS screws etc. complete all as specified and directed.

S&F 200 mm stainless steel barral tower bolt of extruded section complete all as specified and directed.

S&F 300 mm Stainless steel sliding door bolt with hasp and staple(bolt type) including fixing with necessary accessaries complete all as specified and directed.

M&L Preparation of old steel painted surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint to give an even and smooth surface having no sign of brush marks complete all as specified and directed.

M&L for preparation of new steel or iron surfaces of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over and including a coat zink chrome red oxide primer complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595mm of approved texture with Semi perforated 12mm thick micro tegular edged GRG false ceiling tiles, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRCO.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @120 grams per sqm including both sides) comprising of main-T runners of size 15 x 32 mm of length 3000mm, cross-T of size 15 x 32 mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanized mild steel items (galvanizing @80 grams per sqm) i.e. 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall/partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing, complete all as specified and directed.

Dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the permises complete all as specified and directed.

M&L, Non-skid ceramic coloured tiles, joint free tiles 7 to 8 mm thick (square/rectangular) of size 300 x 300 mm , in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement over and including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L first quality coloured glazed ceramic, joint free tiles fixed in pattern of different colour including border of size 300x450x7 mm thick as in vertical surfaces such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles laid over and including 10 mm thick rendering in cement mortar (1:3), including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed. Note :- Pattern of the tiles will be decided by GE at the time of execution.

Demolition of brick work of any description and in any position built in cement mortar including quoins arches and pillars complete all as specified and directed.

M&L Brick work with sub class 'B' Bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 complete all as specified and directed. Note : Contractor will make his own arrrangement of underpinning / holding in position of truss rafter during the time of execution of brickwork as per directed by Eng-in-charge

Excavation in post holes n exc 0.5Cum, getting out , returning filling in and ramming earth or broken rubble mixed with around in layers n exc 50mtr and making good surface in soft/loose soil complete all as specified and directed.

M&L for PCC 1:2:4 Type B2 (using 40mm graded stone aggregate) as in post holes, foundation complete all as specified and directed.

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. (Fe-290 Gde E-165) complete all as specified and directed.

S&F Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with L-type or J-type or cranked hook bolts in lieu of screw in roof, wall etc complete all as specified and directed.

S&F HDPE triple layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 litres capacity hoisted and fixed in position all as specified in SSR Pt-I including for hoisting into position either inside or outside of building including connecting up pipes, securing access cover, float valve,tank adaptor etc of suitable size complete all as specified and directed.

S&F in repair 25mm dia Gun metal globe or gate valve with iron wheel head, screwd both ends for iron pipe complete all as specified and directed.

S&F in repair 20mm dia Gun metal globe or gate valve with iron wheel head, screwd both ends for iron pipe complete all as specified and directed.

S&F GI steel tubing 25mm bore medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Supplying and laying of 1High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in trenches complete all as specified and directed.

M&L ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball with minimum weight 210 gm screwed for 20mm bore dia iron pipe supplied and fixed in repairs complete all as specified and directed.

S&F sprinkler nozzle head Detachable nozzle and spinner complete all as specified and directed.

S&F Agronet of best quality with 20% visibility complete all as specified

M&L Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM (1:6) complete all as specified and directed.

S&F of 12 to 15 mm thick approach/parking tiles/stones 600x600mm from which suitable size shall be cut and applied as per site requirement fixed with adhesive as per manufacturer insturction complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting, bell, bell push etc and making good disturbed surfaces of walls, floor to match with existing specification complete all as specified and directed.

M&L for point wiring for one light point/bell point/exhaust controlled by one switch with 1.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable FRLS with proper colour coding and 1.5 sqmm PVC insulated unsheathed copper conductor single core multistranded cable (green colour) as earth lead in and including concealed non metalic rigid PVC conduit medium grade size 25mm dia with all fittings (ISI Marked) controlled by one switch including pressed steel terminal modular boxes of appropriate size and top cover with suitable size of modular plate with all accessories including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and directed.

All as per item No 57.00 above but upto ceiling height and on surface at ceiling complete all as specified and directed.

All as per item No 57.00 above but for one 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 sqmm PVC insulated unsheathed copper conductor single core cable (green colour) as earth lead in and including pressed steel terminal modular boxes of appropriate size and top cover with suitable size of modular plate with all accessories complete all as specified and directed.

All as per item No 57.00 above but for one socket outlet 5 amps on independent board including pressed steel terminal modular boxes of appropriate size and top cover with suitable size of modular plate with all accessories complete all as specified and directed.

All as per item No 57.00 above but for one socket outlet 5 amps on same board including pressed steel terminal modular boxes of appropriate size and top cover with suitable size of modular plate with all accessories complete all as specified and directed.

M&L for switch modular type single pole one way 1 module 6 amps 240 volts complete all as specified and directed.

S&F switch modular type one way 1 module 16 amps 230 Volts complete all as specified and directed.

M&L for socket 6 amps modular type 2/3 pin combined 2 module, 230 volts complete all as specified and directed.

M&L for socket modular type , 2/3 pin, 6 and 16 amps combined 2 module, 230 volts complete all as specified and directed.

M&L for ceiling rose surface bakelite 3 terminals complete all as specified and directed.

S&F of LED Aluminium batten luminaire surface mounted 4 feet system wattage of 20/22 Watts with lifetime of not less than 50000 burning hours with 70% of its initial lumen maintained.CRI>80, Power Factor>.95 ,THD<20% ,Surge protection 3 KV in CM, IP-20n Protected, meets LED IS Specifications , Class-1 , short circuit and over circuit protection voltage range-150 to 270 AC,system efficiency at luminaire level > 100lumen/watt and ibncluding connecting up with pvc sheathed 1.5 sq mm 3 core copper conductor flexible wire from ceiling rose to fitting fix complete all as specified and directed by Engr-In-Charge. Note:- All the above mentioned specifications will be verified through LM 79 and LM 80 report of NABL accredited lab before supply of LED fixtures.

S&F LED in repair wall security light 20/25 W pressure die cast aluminium IP-66 road way luminaries with high power LED as light source having efficacy 120 lm/W complete all as specified and directed.

S&F VTPN distribution board iron clad, double door with IP-43 1K-09 protection suitable for MCCB as incommer and MCB as outgoing 415 Volts 3 phase 50 C/s 4 way, complete with appropriate size copper bus bar and neutral link, complete with one MCCB 4 pole 415 Volts 125Amps rating with rupturing cap 16 KA of the same make as of VTPN distribution board & with MCBs of required size making connection with thimbles & including cutting chases to wall for fixing DB and making good the disturbed wall surface complete all as specified and directed.

Supply and fix sheet metal enclosure MCB distribution board, 8 way double door with IP-43 protection with 200 Amp rated bus bar complete all as specified and directed.

S&F amp rating 240 V, 10 KA 'C' curve miniature circuit breaker (MCB) 5 to 32 Amp in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

All as per item No 71.00 above but SPN 40 to 63 Amp complete all as specified and directed.

M&L in replacement for submain wiring with two single core PVC insulated flexible copper conductor multistranded cable (FRLS) of size 4 Sqmm with proper colour coding and one single core PVC insulated flexible copper conductor multistranded cable green colour of size 4 Sqmm as earth lead in & including concealed PVC conduit medium grade 32mm dia cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.

M&L in replacement for submain wiring with two single core PVC insulated flexible copper conductor multistranded cable (FRLS) of size 6 Sqmm with proper colour coding and one single core PVC insulated flexible copper conductor multistranded cable green colour of size 6 Sqmm as earth lead in & including concealed PVC conduit medium grade 32mm dia cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.

Dismantling & taking down old exhaust fan and deposited in MES Store & Supply & fix exhaust fans AC single phase 230/ 240 V of size 450 mm sweep with louver with cavity complete all as specified and directed.

Disconnecting & taking down upto 1200/1400m sweep ceiling fan and deposited to MES store yard and Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.00, Air delivery minimum 210 CMM, 350 RPM (tolerance as per IS : 3742019), THD less than 10%,with remote for speed control and all remaining accessories including safety pin, nut bolts, washers, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete all as specified and directed.

S&F in repair electronic fan regulator, socket size, step type suitable for ceiling fan of 1200 / 1400 mm sweep complete all as specified and directed.

Supply only in replacement luminaire diffused recess mounted 2' X2 ', deep drawn CRCA housing with efficacy of 100 lm/W CRI> 90 provides uniform illuminatione 2 soft glare free light complete with driver, holders suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

Supply & Fix Air circulator Fans 230 volts single phase 18 inch wall mounting fan, oscillating 450 mm sweep suitable for wall mounting complete all as specified and directed.

M&L for Earthing complete with galvanised iron earth plate electrode of size 600x600x6mm thick as earth electrode with top edge of the earth plate not less than 1.5mtr below ground level using GI wire 4mm dia as earth continuity conductor connected to earth plate by means of GI thimbles nuts bolts washers all as directed including providing earth wire protection pipe GI light grade15mm dia from earth plate to main switch board/panel, watering pipe 20mm dia with wire mesh and funnel at top, earth pit and RCC pit cover in PCC 1:3:6 adequate quantity of charcoal dust and salt all around the erth plate, earth work in any type of soil remaing surplus excavated material all as required at site and specified in EP No 5 of SSR part I 1991 complete all as specified and directed and testing on completion.

Please Enable Macros to View BoQ information