PROVN OF VIEW CUTTER AND CERTAIN OTHER SANCTIONED WORKS UNDER AGE B/R-I AND AGE E/M OF GE SOUTH DELHI CANTT-10

Amount

Excavation in post holes in hard / dense soils , each not exceeding 0.50 cum, getting out, returning filling in and ramming earth in layers not exceeding 25 cm including watering & removing surplus soil to a distance not exc. 50 m & making good surface complete all as specified and as directed

M&L for cement concrete (1:4:8) Type D-2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

M&L for cement concrete type B-2 (1:2:4) 40mm graded stone aggregate roof kerb and mass concrete complete all as specified and directed.

M&L for mild steel work in tubular trusses including special shaped washer, cleats etc complete using ERW or induction butt welded tubes confirming to IS: 1161-1979 grade st - 240 complete all as specified and as directed.

M & L for mild steel structural steel in roof, purlins, crane gantries of angle or other section gusset plates, Flat Iron rails braces etc, drilled for fixing, and other covering r etc to be prepared for hanging and sliding with and including either hooks and hinges and other covering running rails and guides and hanging also fastening and fixing complete conforming to Fe- 410-W ( Grade E-250, quality-B), complete all as specified and as directed.

S&F 2 mm thick fibre glass reinforced translucent corrugated/plain sheeting with two corrugation side lap of any colour and pattern fixed with coach screw and washer in roof/wall , complete as specifed and as directed.

M&L for preparation of new steel surfaces of any description , not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zink chrome primer, complete all as specified and as directed.

Excavation in trenches in any type of soil not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out for laying of cables complete all as specified and as directed.

M&L for 100 mm thick cement concrete (1:4:8) Type D-2, (40 mm graded crushed stone aggregate), as in sub-base of floor and similar works complete all as specified and as directed.

Material & labour for brick work with sub class B old size burnt bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specifie and as directed.

M&L for 15 mm thick rendering in cement mortar 1: 4 on faces of brick work or concrete surfaces, finished fair and even complete all as specifie and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick, complete all as specified and directed by Engr-in-Charge.

Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above starting point complete all as specified and as directed.

Surface excavation in soft/loose soil, not exceeding 30 cm deep and averaging 15cm deep and getting out, complete all as specified and as directed.

M&L for 75 mm thick cement concrete (1:3:6) Type C-2, (40 mm graded crushed stone aggregate), as in sub-base of floor and similar works complete all as specified and as directed.

M & L for 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

S & F 25 mm thick factory made rubber moulded glossy finished cement concrete tiles size 300X300 mm with approveed colour, design & pattern as in footpath, park lawns, drive ways etc laid in required colour & pattern over and including 20 mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M & L for cement concrete Type B-1 , 20mm gded agg 1:2:4 in road kerbs or mud stops, rounded or chamfered on edges , steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones, bed plates, kerbs not provided . complete all as specified and as directed.

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M&L for non skid coloured ceramic tiles jointless 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set & jointed in neat cement slurry & pointed in coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 for laying floor finish including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and as directed.

M & L for glazed ceramic coloured tiles 350mm x 250mm x 7 mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match in vertical surfaces such as skirting /dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10m thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces as backing coat including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and as directed.

Cutting holes in brick walls in built in cement mortar or cement lime mortar and stone walls not exceeding 150 sqcm including making good to original surface complete alll as specified and directed.

M & L for cutting chases ,pinning in , making good to facings where required and pointing in cement mortar 1:3 to ends or edges or landings, steps, cills, sunshades,shelves,lintel,etc and cutting in chases for concealed conduit wiring, etc and making good, cutting not exceeding 10 cm girth complete all as specified and as directed.

Supply, fabrication & installation of box-type modular kitchen cabinets (below/above counter) up to 600 mm depth (or as per actual size at site) made of 18 mm thick HDHMR pre-laminated waterproof & termite resistant board for top, bottom, back, partitions, drawers, shelf etc. Shutters & exposed surfaces made of 18 mm thick HDHMR laminated with 1 mm thick acrylic high gloss sheet on one side and 0.8 mm balancing laminate on other side, factory pressed. Edges finished with PVC edge banding tape applied by edge bending machine etc including auto closing spring loaded hinges(hydraulic type), magnetic catchers, SS handles stainless, steel soft closing heavy type telescopic drawers channel etc complete all as per approved shop drawing and as directed. Note :- i) Fittings & fixtures shall be deemed to be included in rate quoted by the tenderer. ii) The measurement for payment shall be based on the superficial area of the modular kitchen cabinets.

S & F Modular Cabinet Kitchen accessories of Stainless Steel grade-304, 6mm thick rod including :- (i) Perforated Cutlery basket, (ii) Grain trolley, (iii) Thali basket, (iv) Cup & saucer basket, (v) Glass basket, (vi) Plate basket, (vii) Premium magic corner (viii) Oil Pull out Tray ( Triple basket layer) , (ix) Dust bin, (x) Cleaning kit rack of size as per site requirement all specified and directed.

S&F galvanised steel water tubing 15 mm bore 'medium grade' with and including all fittings and fixed to walls or laid in floors complete all as specified and as directed.

S&F 15 mm size brass chromium plated two way angle valves fancy type cast copper alloy, complete all as specified and as directed.

M&L for point wiring with multi stranded copper conductor 1.5 Sqmm nominal area PVC insulated, unsheathed, FRLS cable 1100 volts grade ISI marked drawn through and including PVC casing & caping on surface of wall, not less than 25mm width conforming to IS 9537 (Part-II) including modular sunken pressed steel terminal boxes 1.8mm thick of required size and modular white cover plate with all accessories including 1.5 sqmm multi stranded copper conductor PVC unsheathed cable earth wire to common earth and connected to earth dolly complete and making good the disturbed surfaces of walls including necessary touch up with adjoining surface of disturbed area i.e with OBD/colour wash/white wash as the existing finishes etc. complete all as specified and as directed. (a) One 3 Pin socket oulet 5 amp on the independent board controlled by one way switch

S&F Switch modular type, 1 Module, 6 Amps one way complete all as specified and as directed.

S&F ceiling rose surface bakelite 65x50 mm two to three terminals complete all as specified and as directed.

S&F Socket outlet modular type 2M, 2/3 pin, 6 Amp complete all as specified and as directed.

Supply and fixing of domestic wall-mounted kitchen fan (STING), white colour, 230 V, 400 mm sweep, 100 CMM air delivery, 2100 RPM, complete with copper-wound motor, blades, anchor bolts, wiring connections and all required accessories, installed and commissioned all as specified and as directed.

M&L for point wiring with multi stranded copper conductor 1.5 Sqmm nominal area PVC insulated, unsheathed, FRLS cable 1100 volts grade ISI marked drawn through concealed PVC conduit on surface of wall, not less than 25mm dia including modular sunken pressed steel terminal boxes 1.8mm thick of required size and modular white cover plate with all accessories including 1.5 sqmm multi stranded copper conductor PVC unsheathed cable earth wire to common earth and connected to earth dolly complete and making good the disturbed surfaces of walls including necessary touch up with adjoining surface of disturbed area i.e with OBD/colour wash/white wash as the existing finishes etc. complete all as specified and as directed. (a) One light/fan/bell point controlled by one way switch Note:- the rate is inclusive cutting /chasing and making good the disturbed surface with cm 1:3 and same surface finishes with the adjoining surface of disturbed area with OBD/colour wash/white wash complete

All as per Srl item No. 33.00 here-in-before, but for One 3 Pin socket oulet 5 amp on the independent board controlled by one way switch

All as per Srl item No. 33.00 here-in-before, but for one 3 pin socket outlet 5 amps on same board

M&L for concealed point wiring complete with stranded copper conductor 2.5 sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable drawn through concealed PVC conduit with Modular steel terminal boxes 1.8mm thick factory made including white cover modular plate with frame suitable for modular switches, modular sockets, modular fan regulators etc of required size complete including 2.5 sqmm copper cable earth continuity wire to common earth and connected to earth dolly complete all as specified for power point controlled by one 15 Amp switch one way using cable (2.5 Sq mm for phase and neutral and 2.5 sqmm for earthing) . Note :- The rate is inclusive cutting/chasing and making good disturbed surface with CM 1:3 and same surface finishs with the adjoining surface of disturbed area with OBD/Colour wash/white wash complete.

M&L for concealed point wiring complete with stranded copper conductor 4 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable drawn through concealed PVC conduit complete including 4 sqmm copper cable earth continuity wire to common earth and connected to earth dolly complete all as specified for one socket outlet for modular AC Box on Independent board with cables 4.0 sqmm size for phase and neutral and 4 Sqmm for earthing complete. Note:- the rate is inclusive cutting /chasing and making good the disturbed surface with cm 1:3 and same surface finishes with the adjoining surface of disturbed area with OBD/colour wash/white wash complete

S&F Switch modular type 1M, 16 Amp with red indication light complete all as specified and as directed.

S&F Socket outlet modular type 2M, 3 pin, 16 Amp complete all as specified and as directed.

S&F Modular AC Box with socket and MCB SP 20 Amp complete with Metal box , white colour plate and frame complete in replacement of sheet metal enclosures as per site requirement , complete all as specified and directed.

S&F VTPN DB 6 way, 4Pole double door,415V vertical type for fixing MCCB up to 100 Amps as incommer and MCBs as out goings with metel door , rubber gasket and IP 43 Protections and connecting complete all as specified and as directed.

S&F MCCB 3 Pole 415V fixed type , 250Amps with breaking capacity 36Ka with copper lugs complete all as specified and as directed.

S&F of sheet metal enclosures for DBs when MCBs to be used SPN -12 way, 240V with busbar as per site requirement complete all as specified and as directed.

S&F of sheet metal enclosures for DBs when MCBs to be used SPN -8 way, 240V with busbar as per site requirement complete all as specified and as directed.

Supply and fixing MCB SPN 40 to 63 Amps, 240 vots , 10Ka, 'C' curve all as per site requirement complete all as specified and as directed.

S&F MCB SP 63 Amps 240 Volts, 10kA, `C' curve all as per site requirement complete all as specified and as directed.

S&F MCB SPN 40 Amps 240 Volts, 10kA, `C' curve all as per site requirement complete all as specified and as directed.

S&F MCB SP 6 to 32 Amps 240 Volts, 10kA, `C' curve all as per site requirement complete all as specified and as directed.

M&L for Earthing complete with galvanized steel earth plate 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate n.less than 1.5 m below normal ground level, connected to galvanized iron wire 4 mm as earthing lead by means of bolts, nuts, check nuts & washers of galvanized iron or steel besides building at all joints as shown in drgs and including excavation and earth work, GI pipe light grade 25mm bore of protection of GI wire from earth electrode, supply and laying charcoal dust, common salt, PCC (1:2:4) type B-1 Chamber and MS angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type B-1using 20 mm graded stone aggregate Reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia, PGI funnel and wire mesh , 20 mm dia GI Pipe light grade for watering, all as shown in Electrical Plate No.05 of SSR-2009 (Part-I) and connected to earth test point including testing etc. complete all as specified and as directed.

M&L for Sub Main wiring using single run PVC FRLS grade Insulated unsheathed, multistrand copper conductor cable 2 runs of 10 Sqmm for phase and neutral and 1 run of 10 Sqmm for earth wire drawn through concealed PVC conduit wiring in wall not less than 25mm dia with all fittings like tees, bends, junction/ terminal boxes etc as per site requirement complete all as specified and as directed. (Note:- Phase should be of Red /Yellow/Blue, neutral should be of back and earthing wire should be of green colour. 2 runs of cable for phase/ neutral and 1 run for earth will be measured and paid as one unit length).

M&L for Sub Main wiring using single run PVC FRLS grade Insulated unsheathed, multistrand copper conductor cable 2 runs of 6 Sqmm for phase and neutral and 1 run of 6 Sqmm for earth wire drawn through concealed PVC conduit wiring in wall not less than 25mm dia with all fittings like tees, bends, junction/ terminal boxes etc as per site requirement and complete all as specified and as directed. (Note:- Phase should be of Red /Yellow/Blue, neutral should be of back and earthing wire should be of green colour. 2 runs of cable for phase/ neutral and 1 run for earth will be measured and paid as one unit length).

S&F MCCB 4 Pole 415V fixed type , 350Amps with breaking capacity 36Ka with copper lugs complete all as specified and as directed.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 Sqmm 3.5 core complete all as specified and as directed.

Supply and laying Double wall Corrugated (DWC) pipe in excavation of trenched of 63 X 50 mm size including all connecting necessary items complete all as specified and directed.

Supply and fixing GI Pipe 40mm medium grade with all fittings for passing of cables fixed to pole / wall / laid under floor or roads including all fixing accessories complete for protection of cable of size 120 Sq mm dia bore complete all as specified and directed.

Supply and fix in repair 36 W LED Recess mounting 1'x4' LED Luminaire having CRCA stell sheet housing comprising of LED's connected in series parallel,. Opal diffuser fixed in separate CRCA sheet steel frame. Opal diffuser frame is held with screws and SS strings and it can be suspended for easy maintenance Driver. constant current output driver. Finish Housing white powder coated (RAL9016). Fixture should have minium system level >=100 Lumens/ watt ,. Life of fixture 50K Hrs @ L70B50 Lumen maintenance, CCT 5700-6500k with same Limens/w CRI> 80, THD < 10%@ 240V Ac. An operetaing Voltage Range of 140-270V Minium Internal Surge Protection 3 Kv, IP 20 BIS certification ids required fo rLED Driver & Liminaire , OEM should have in house NABL Accrediated R&D and own Luminiare manufacturing facility to provide LM 79 report in house NABL accredited lab & LM80 report issued by LED manufacturer complete all as specified and directed.

M/S Malik Construction Corporation (BID ID -3508889)

H S KALSI AND BROS (BID ID -3508768)

verma enterprises (BID ID -3509125)

HANUMAN BUILDERS (BID ID -3508247)

M/s S.G. BUILDERS (BID ID -3505485)