SPECIAL REPAIRS TO OR INSTITUTE BLDG NO. P-15 AT 2 AFSB MYSORE

Amount

Taking down chowkats or frame with shutter (without taking off shutter from frame) area not exceeding 1.5 sqm each all as specified and as directed.

Taking down chowkats or frame with shutter (without taking off shutter from frame) area not exceeding 1.5 sqm each as in steel windows and ventilators all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc., complete all as specified and as directed.

Taking up or down 20 mm bore mild steel galvanised tubing with all fittings and connections including cleaning for re-fixing or removal to store complete all as specified and as directed.

Dismantling water tanks, capacity exceeding 250 litres but not exceeding 500 litres and removing complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level complete all as specified and as directed.

Dismantling of 100 mm internal dia cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required all as specified and directed.

Material and Labour for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area all as specified and as directed.

Material and Labour for forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, in cement mortar 1:4 complete all as specified and as directed.

Material and Labour for making good under cills or over arches, lintels and bressummers, including all pinning when necessary, in cement mortar 1:4 complete all as specified and as directed.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified and as per drawings and directed by Engr-in-Charge

Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, in the frame at site as per specification & drawing and as directed

Supply and fix butt hinges, 75mm size, medium weight, cold rolled mild steel all as specified and directed

Supply and fix 75 mm long aluminium anodised barrel tower bolts of extruded section and fixed, all as specified and directed

Supply and fix 75 mm long extruded aluminium alloy handles, cast type, anodised all as specified and directed

Supply and fix 150 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified and directed

Supply and fix in repairs harrison rails, anodised aluminium alloy with fixing brackets, stops, rollers etc. all as specified and directed

Supply and fix in repairs brass chromium plated tubular towel rail 20 mm dia ‘D’ type 60 cm long between flanges including brackets complete all as specified and as directed.

Supply and fix aluminium anodised powder coated windows, frames with 3 channels for sliding glazed and mosquito proofing shutters & with necessary accessories like jointing cleats, rubber packing, beading and screws etc, including 4mm thick glass panes, stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm for mosquito proofing and powder coated aluminium grill of design DG-103 as per TD drg no AFB/TD/352/11 Sht 1/2 & 2/2 and AFB/TD/237/05 Sht 1/1, complete all as specified and directed.

Supply and fix aluminium anodised powder coated louver ventilators with necessary accessories like jointing cleats, rubber packing, beading and screws etc, including 4mm thick tinted glass cut to 10 cm wide strips as in louvers, stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm for mosquito proofing and powder coated aluminium grill of design DG-103 as per TD drg no AFB/TD/352/11 Sht 1/2 & 2/2 and AFB/TD/237/05 Sht 1/1, complete all as specified and directed.

Material and Labour for cement concrete 1:3:6, type C-1, (using 20 mm graded stone aggregate), 75mm thick as in plinth protection, finishing cement concrete surface even and smooth without using extra cement, laid in panels including necessary form work and forming construction joints filled with seailing compound grade - A complete all as specified and directed.

Material and Labour for 100mm thick cement concrete 1:4:8, type D-2 (using 40mm graded aggregate) as in sub base to floors complete all as specified and directed.

Material and Labour for pre polished chequered cement concrete coloured tiles, 300 mm x 300 mm, 20 mm thick, laid, set, jointed and pointed in neat cement slurry with white cement and pigment over and including screed bed 20 mm thick in cement mortar 1:4 complete all as specified and directed

Material and Labour for coloured non skid ceramic joint free tiles 7 to 8 mm thick (square/rectangular) area exceeding 0.06 Sqm but not exceeding 0.11 Sqm laid in floors etc., set, jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Material and Labour for coloured non skid ceramic joint free tiles 7 to 8 mm thick (square/rectangular) area exceeding 0.11 Sqm but not exceeding 0.18 Sqm laid in floors etc., set, jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Material and Labour for coloured non skid ceramic joint free tiles 7 to 8 mm thick (square/rectangular) area exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in skirtings etc., set, jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including a backing coat of rendering 10 mm thick in cement mortar 1:4 complete all as specified and directed.

Material and Labour for glazed ceramic tiles of size 300 x 200 x 7mm thick on vertical surfaces as in dado/skirting set, jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including a backing coat of rendering 10mm thick in cement mortar 1:4 complete all as specified and as directed.

Material and Labour for 18-20 mm thick granite stone slab (of any colour table rubbed and polished) as in steps, window-cills, cooking platforms, urinal partitions and the like, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone slab including grinding, polishing, rounding the exposed edges and necessary moulding, laid over and including screed bed 15 mm thick in cement mortar 1:4 including dismantling old stone slab any type, thickness complete all as specified and as directed.

Supply and fix 15 mm bore mild steel galvanised tubing medium grade with all fittings and fixed to walls and ceilings or laid in floors including cutting chases for concealed water tubing etc., and making good to facing where required and pointing in cement mortar 1:3, cutting not exceeding 10 cm in girth and including taking up or down old steel tubing and connections complete all as specified and as directed.

Supply and fix 20 mm bore mild steel galvanised tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Supply and fix in repairs bib taps cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down for iron pipes or for brass ferrule, bore dia of pipe 15 mm complete all as specified and directed.

Supply and fix in repairs stop valves fancy type, cast copper alloy, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for union, bore dia of pipe 15mm complete all as specified and directed.

Supply and fixing in repairs vitreous china water closet orissa pattern of size 580 x 450mm with P or S trap of size 110/110mm including provision of lime concrete bedding complete all as specified and as directed.

Supply and fix in repairs 10 litres capacity PVC valveless, syphonic action type flushing cistern white with inlet, ball valve, float and handle including brackets and PVC connection 15mm size with PTMT nuts of length 600mm and 15 mm angle stop valve of PTMT (Minimum weight 15mm-90gms) any colour, high pressure screwed for iron pipe complete all as specified and directed.

Supply and fixing in repairs glass self assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide, 60 cm long with chromium plated bracket guard and rail all as specified and directed.

Supply and fixing in repairs soap dish holder Make: Jaquar, Cat I. No. AKP-35731P all as specified and directed.

Supply and fix sinks with drainage board made of stainless steel 1.0mm thick kitchen or laboratory with plugs, washers, CP waste coupling (half or full threaded) size suitable for sink and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Supply and fix 500 Ltr capacity rotational moulded polythene water storage tank (Cylinderical vertical with closed top) hoisted and fixed in position and connecting the inlet and out let pipe etc complete all as specified and directed.

Supply and fix in repairs 25 mm ball brass valves. high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed.

Supply and fix in repairs PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement complete all as specified and directed.

Supply and fix in repairs 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in floors complete all as specified and directed

Supply and fix in repairs 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls complete all as specified and directed

Supply and fix in repairs PVC (SWR) bends, 110mm bore, any radius all as specified and directed.

Supply and fix PVC (SWR) 110mm bore, junction single (single T) Equal or unequal complete all as specified and directed.

Supply and fix PVC (SWR) couplers 110/110 mm bore complete all as specified and directed.

Supply and fix PVC (SWR) vent cowl 110 mm bore complete all as specified and directed.

Supply and fix PVC (SWR) 'P' trap 110/110 mm bore complete all as specified and directed.

Material and labour for complete removal of existing treatment including preparation of old decorated surfaces of walls and applying two coats of white wash over chalk whiting all as specified and directed.

Material and labour for complete removal of existing treatment including preparation of old decorated surfaces of ceilings and applying two coats of white wash over chalk whiting all as specified and directed.

Material and labour for complete removal of existing treatment including preparation of old decorated surfaces of wall and applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as specified and directed.

Material and labour for complete removal of existing treatment including preparation of old decorated surfaces of ceiling and applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as specified and directed.

Material and labour for complete removal of existing treatment including preparation of old decorated surfaces of wall and applying two coats weather proof exterior acrylic emulsion paint with anti fungal property over a coat of alkali resistant primer complete all as specified and directed.

Material and labour for preparation of old painted wood or wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed

Material and Labour for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Taking down carefully existing copper /aluminium point wiring (Light, fan, socket or power) complete including fittings and fixtures such as switches ceiling roses socket, regulator etc. and making good disturbed surfaces of walls, floors etc to match with the existing surface/ finishes complete all as specified and directed.

Material and Labour for Point wiring complete with 1.5 sqmm single core FRLS PVC insulated and unsheathed cable 1100 volts grade, confirming to IS-694 and marked, with multistranded copper conductor drawn through and including PVC casing and caping of suitable size with all accessories in walls, ceilings etc., including 1.5 sqmm, single core FRLS, PVC insulated unsheathed 1100 volts grade, copper cable green in colour as earth continuity conductor and connected to common earth dolly, fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls, with 3mm thick laminated sheet top cover for housing the switches, socket outlets, fan regulators etc., and connected to existing DB all as specified and as directed for one light/fan/bell point controlled by one one way switch.

All as per item No. 59 here-in-before but for 3 pin, 5 Amps socket outlet controlled by one, one way switch on independent board.

All as per item No.59 here-in-before but for 3 pin 15 Amps switch socket outlet on independent board with 2.5 sqmm single core FRLS PVC insulated and unsheathed cable 1100 volts grade copper cable and provision of 2.5 sqmm FRLS PVC insulated unsheathed cable 1100 volts grade stranded copper conductor cable for earth continuity conductor connected to common earth dolly connecting up to fittings complete.

Supply and fix switch piano, flush type 5 Amps 240 V, single pole, one way all as specified and as directed.

Supply and fix switch piano, flush type 15 Amps 240 V, single pole, one way all as specified and as directed.

Supply and fix socket out let 2 in 1, 3 pin, 5 Amps, 240 Volts flush type, all as specified and as directed.

Supply and fix socket out let 2 in 1, 3 pin, 5 and 15 Amps, 240 Volts flush type, all as specified and as directed.

Supply and fixing bell push, flush type 5 Amps, 230 Volts complete all as specified and as directed

Supply and fixing bell, AC 230 Volts single pole complete all as specified and as directed

Supply and fix ceiling rose, surface type PVC/ Polycarbonate, isolated body, three terminal, ISI marked complete all as specified and as directed.

Supply and fix stepped type electronic fan regulator flush type, 240 V 50 Hz complete all as specified and as directed.

Supply and fix in repairs energy efficient LED batten tube light fitting T8 1 X 22 watt LED tube including crystal glass LED tube light with integrated electronic driver (double side connection) of 20 watt, 4ft in length, nano diffuser technology and connecting with twin core flexible copper cable from fitting to ceiling rose all as specified and as directed. Make: Havells Model No REGALBATTENT8UPTO1X22WSSBSWH for batten and CRYSTAL1213T8DSTL20WLED865SGLASS or equivalent in Crompton/Philips/Bajaj

Supply and fix in repairs energy efficient surface and wall mounted LED batten with aluminium housing & integrated electronic driver of 10 watt , 2 ft length Land connecting with twin core flexible copper cable from fitting to ceiling rose all as specified and as directed. Make: Havells Model No LUMILINEPLUSBS10WLED865SPCSS or equivalent in Crompton & Philips

Supply and fix lamp holder, PVC/polycarbonate with back plate suitable for batten fittings with LED bulb 7 watt complete all as specified and directed.

Supply and fix in repairs sheet metal enclosure distribution board SPN, 08 ways, 240 volts, single door, with 200 amps rated bus bar, neutral link, blanking plate with IP 43 protection and suitable for MCBs including taking down old unserviceable DBs complete all as specified and as directed.

Supply and fix in repairs MCB single pole, 240 volts, 6 to 32 Amps, 10 KA rupturing capacity, confirm to IS/IEC 60898-1, C' series complete all as specified and as directed.

Supply and fix in repairs MCB SPN, 240 volts, 32 Amps, 10 KA rupturing capacity, confirm to IS/IEC 60898-1, C' series complete all as specified and as directed.

Material and Labour for replacement of earthing complete with galvanised iron earth plate electrode of size 600mm x 600mm, 6mm thick, buried directly in ground vertically at a depth not less than 2.25 metres deep below normal ground level with top edge of the earth plate not less than 1.5 metres below normal ground level and filling with mixture of common salt and charcoal surrounded all sides 15cm thick (minimum)and connecting electrode with galvanised iron wire of 4 mm dia by means of bolts, nuts, check nuts and washers made up of galvanised iron or steel and protected by light grade 15mm dia galvanised iron pipe connected to main switch board or main control board and watering arrangement with 20 mm bore GI medium grade pipe, GI funnel with wire mesh, including PCC 1:3:6 type C-1 pit with cover made of RCC 1:2:4 type B-1, reinforced with welded steel wire fabric not less than 4 kg per sqm with handle and angle iron frame, including necessary excavation and earth work, returning filling and disposal of surplus soil to a distance not exceeding 50 m all as specified and as shown in electrical plate No. 3 of MES schedule part-1 connected to test point terminal all as specified including taking down old earthing & testing new earthing on completion all as directed.

S S BUILDERS

ANAND REFRIGERATION

Sri Lakshmi Venkateswara Enterprises