PROVN OF BOUNDARY WALL AT CENTRE DRILL GROUND OF ARTY CENTRE, HYDERABAD UNDER GE GOLCONDA

Amount

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in hard/dense soil.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., area not exc. 10 Sqm on plan and getting out in hard/dense soil.

M & L for plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete.

M&L for walling of squared rubble, regular coursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 Secunderabad type complete all as specified and directed

M & L for PCC 1:2:4 type - B1, (using 20mm graded stone aggregate) as in copings, cornices and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and as directed.

M & L for rendering in cement mortar 1:4 15mm thick on fair faces of stone masonry or on one side of lathing finished even and smooth without using extra cement complete all as specified and directed.

M&L for 110 mm dia bore PVC (SWR) pipes fixed in walls (as in weep hole) complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing excavated material n exc. 250m and depositing where directed at a level n exc. 1.5m above the starting point in soils.

M&L for RCC (Nominal mix) type A1 1:1.5:3 (using 20 mm graded stone aggregate) in lintel bands, roof beams and cantilevers etc comlpete all as specified and directed by Engineer-In-Charge.

Use and waste of form work to sides and soffits of floor or roof beams, lintles, cantlevers etc for rough finished surface of concrete comlpete all as specified and directed by Engineer-In-Charge.

M&L for RCC (Nominal mix) type A1 1:1.5:3 (using 20 mm graded stone aggregate) as in arches comlpete all as specified and directed by Engineer-In-Charge..

Use and waste of formwork to sides and soffits of arches (curved) complete all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length bent to shap required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia) or securing with clips complete all as specified and directed.

All as per item No. 14 here in above but 5mm dia and over upto and incl 10 mm dia in spacers, stirrups and binders.

M & L for fly ash brick masonry straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L for fly ash brick masonry, straight or curved on plan to any radius in half brick thick walls, built in CM (1:4) complete all as specified and directed.

M&L for 15mm thick in CM 1:4 rendering on brick or concrete surfaces finished even and smooth without using extra cement on walls complete all as specified and directed

M&L for praparation of newly plastered surfaces of walls and applying two coats of weather coat (APEX) from asian paint or equivalent over a coat of primer comlpete all as specified and directed by Engineer-In-Charge.

S & F Mild steel framed work as in ornamental and intricate design framed and hung/ sliding gates, including pintle hinges / roller, stops, hand made sliding bolts etc. and similar work confirming to Fe 290 Gde - E - 165 comlpete all as specified and directed by Engineer-In-Charge.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide zinc chrome primer comlpete all as specified and directed by Engineer-In-Charge.

Extra over rendering for work in isolated width not forming part of general rendering as in bands, cornices, drip moulds and similar work n. exc. 15 cm width or girth complete all as specified and directed by Engineer-In-Charge.

M & L for forming square grooves in plaster n exc 12mm deep and n exc 15mm on face comlpete all as specified and directed by Engineer-In-Charge.

Supply and fixing LED street light fitting 100 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics with IP 65/66 protection complete.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6 sq mm 2 core including taking out existing cable complete all as specified and directed.

M & L for cutting of road/hard standing made of concrete or premix carpet, WBM, soiling and morrum filling including excavation for laying of cable/pipe all as directed and making good the road/hard standing by using all old/new materials and with PCC (1:2:4) etc, required to match with the existing surface complete all as specified and directed.

M&L GI tubing , light grade, with all fittings for cable protection at road crossing / on poles and tubing sealed at both ends after laying the cables complete all as specified and directed of size 25 mm bore.

S&F hot press moulded SMC junction box of size 270mm x 200mm x 135mm with right openable hinged door with two numbers aluminium bus bars mounted on porcelain insulator including clamps of MS flat iron 25 x 3 mm with bolts and nuts including one MCBSP 6A, 10KA for ON/OFF street light, fixed on pole / wall complete all as specified and directed.

THE DECAN ENGINEERING AND REFRIGERATION COMPANY

BHAGYARAM ENTERPRISES

STANDARD AGENCIES

sandhya enterprises

M/S Veerabhadra Constructions

Sri Lakshmi Enterprises

BUILDWEL