Repair replacement sewage line cleaning drainage and culvert and repair manhoses chambers soakage well desluding of septic tank soakage well for Kanjoli line and Dayal Bagh at Bharatpur Mil Stn

Amount

Excavation in trenches, not exceeding 1.5 metre wide and not exceeding 1. 5 metre in depth; for foundation or for manholes not exceeding 10 Sqm on plan and not exceeding 1.5 metre in depth and getting out in soft/loose soil complete all as specified.

All as per item No. 1 above but exceeding 1.5 metre depth and not exceeding 3 metre in depth complete all as specified.

Returning filling in, including spreading, levelling, watering and well ramming in layers each not exceeding 25 cm depth in soft/loose soil complete all as specified .

Removing surplus spoil to distance not exceeding 50 metre and depositing where directed at level not exceeding 1.5 metre above the starting point complete all as specified .

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete pipe & PVC pipe) set in cement mortar for 150 mm dia pipe or less, complete all as specified.

S&F 150 mm dia Reinforced concrete pipe Class NP-2 with one collar per length joint with CM 1:1 with spun yarn and tested complete all as specified .. Note: Excavation & earthwork shall be measured and paid separately complete all as specified.

M&L for cement concrete 1:3:6 type C-2 (using 40 mm graged stone aggregate) as in concrete bed to drain pipes of 150mm bore including packing under, and haunching against the sides of pipes after they are laid and tested, complete all as specified.

Dismantling of cast iron drain pipe of any size , jointed in CM and taking out of trenches, complete all as specified. Note: Excavation & earthwork shall be measured and paid separately.

S&F cast iron soil, waste and vent pipe spun centrifugally cast iron of 100 mm bore as per IS 3989 , ISI marked in any length, with or without ears, with cement joints, laid in trenches or in floors etc complete all as specified.

S&F cast iron soil, waste and vent pipe spun centrifugally cast iron of 100 mm bore as per IS 3989 , ISI marked in any length, with or without ears, with cement joints, fixed to wall including necessary clamps complete all as specified.

S&F in repair cast iron bend of 100 mm bore with oval access door complete all as specified.

Taking down cement or cement lime plaster of any description from brick or stone walls including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified.

Demolition of brickwork or stone boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified.

Demotion of concrete of any description and in any position not otherwise specifically provided for, complete all as specified.

Brickwork with sub-class ‘B’(old size) burnt clay bricks straight or curved on plan exc 6 metre mean radius built in cement & sand mortar 1:4 complete all as specified.

M&L for rendering 10 mm thick in cement and sand mortar 1:6 on fair faces of brick work or concrete surfaces including finishing the surface even and smooth without using extra cement, complete all as specified.

M&L for rendering 15 mm thick using cement and sand mortar 1:4, mixed with water proofing compound as per manufacturer’s instructions, on fair faces of brick work & cement concrete surfaces including finishing the surface even and smooth without using extra cement, complete all as specified. Note : Water proofing compound shall be measured and paid separately.

Supply only integral water proofing compound ISI Marked, complete all as specified.

M&L for PCC, 1:4:8 type D-2 using 40mm graded stone aggregate in foundation, filling and mass concrete complete all as specified.

M&L for PCC, 1:2:4 type B-1 using 20 mm graded stone aggregate as in surface channels, drains and inside the manhole complete all as specified.

M&L for providing cement concrete 1:2:4 Type B-1 (using 20mm graded stone aggregate) as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified.

Extra forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms,moulds, mitered/stopped etc complete all as specified . (Note: Inner girth shall only be measured)

All as per item No 23 above but add to or deduct for each 25 mm girth or part thereof over or under 30 cm, complete all as specified..

M&L for preparation of newly plastered surfaces of wall including cornices, pillasters etc and applying two coats of cement based paint, white or tinted over a coat of alkali resistant primer complete all as specified .

Demolition of stone slabs and tiles of any description or thickness in floor, apron etc laid dry and pointed etc., complete all as specified.

M&L for 20-25 mm thick sand stone slab as manhole cover complete all as specified .

M&L for RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in manhole cover slab set in CM 1:4, complete all as specified.

S/F mild steel TMT bars 6 to 8mm dia and over cut to length, bend to shape required including cranking, bending and binding with mild steel wire (annealed) not less then 0.9 mm dia, complete all as specified.

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and forming benching as required, complete all as specified.

Demolition of cement concrete (un-reinforced) in ground floors and pavings laid in any description and in any position n.exc 15 cm thickness (below or above GL), complete all as specified.

M&L for 40 mm thick 1:2:4 type B-1 (using 20 mm graded stone aggrgate) finished even and smooth with using extra cement, complete all as specified.

M&L for 75 mm thick cement concrete 1:3:6 Type C-2 (using 40 mm graged stone aggregate) as in plinth protection etc complete all as specified .

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to stores and rubbish off the premises, complete all as specified .

M&L for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of CM 1:6, complete all as specified .

M&L for coloured glazed ceramic coloured tiles of size 300mm x 200mm x 7mm thick on vertical surface such as skirting dado etc including 10mm thick rendering in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified.

S&F GI tubing medium grade with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm including taking up or down the existing unserviceable GI tubing, complete all as specified.

S & F GI tubing medium grade with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm including taking up or down the existing unserviceable GI tubing, complete all as specified and as directed.

Disconnecting existing tanks of capacity exc 250 litres & n exc 500 litres, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position after cleaning and removing all scale and dirt, etc. from tanks and from mouths of circulating pipes, etc. complete all as specified.

Dismantling old unserviceable water tanks and S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of capacity 500 litres, white colour, triple layered, hoisted and fixed in position & including 20 mm brass ball valve, complete all as specified .

Dismantling old unserviceable water tanks and S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of capacity 1000 litres, white colour, triple layered, hoisted and fixed in position & including 20 mm brass ball valve, complete all as specified .

S&F in repair Vitreous China squatting pan “Orissa” pattern, size 580x440mm, white, with integral foot rests and 'P' or 'S' trap (excluding flushing cistern and flush pipe), including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. including making good to floor complete all as specified. Note: The disturbed surface of floor shall be made good as per existing specification without any extra cost to the Govt.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white, including all required fittings , complete all as specified.

S&F in repair wash hand basin vitreous china, size 550 mm x 400 mm, white, flat back, including CI brackets, pillar tap fixed to 15mm bore pipe, long body fancy type cast copper alloy with capstan heads, chromium plated screwed down high pressure, with ot without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, CP waste fitting for waste pipe 32 mm dia with brass coupling, center hole CP grating including pinning in ends of brackets etc, complete all as specified.

S&F in repair PVC 10 ltrs , valveless, syphonic action type, flushing cistern, white, low level, with inlet, ball valve, float and handle, including 32 mm bore PVC flush pipe brackets complete all as specified.

S&F in repair PVC connection 15 mm size with PTMT nuts of length 450 mm, complete all as specified .

S&F plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified .

S&F in repair Bib tap, cast copper alloy chromium Plated fancy type/ long body with crutch or butterfly handle, screwed down, suitable for 15mm nominal bore iron pipe screwed for iron or brass ferrule and fixed, complete all as specified.

S&F in repair 15 mm bore Stop valves, fancy type chromium plated screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified .

S&F in repair pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shank and fly nuts, with or without lettered "Hot" or "Cold" suitable for 15 mm nominal bore iron pipe, screwed for iron pipe and fixed complete all as specified .

S&F for 110 mm dia PVC (SWR) pipe single socketed in any length fixed with suitable adhesives laid in trenches or in floor complete all as specified .

Ditto all as per Srl item No. 54 here in before but fixed on wall complete all as specified.

S&F in repair PVC (SWR) bend for 110 mm bore pipe, any radius jointed with suitable adhesives complete all as specified .

S&F for 75 mm dia PVC (SWR) pipe single socketed in any length fixed with suitable adhesives laid in trenches or in floor complete all as specified .

All as per Srl item No. 57 here in before but fixed on wall complete all as specified.

S&F in repair PVC (SWR) bend for 75 mm bore pipe, any radius jointed with suitable adhesives complete all as specified.

S&F in PVC SWR) 'S' trap of 110 mm bore, complete all as specified.

S&F for MS work for bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay) conforming to Fe.290. Gde-E-165. complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size n. exc 1.5 Sqm each complete all as specified.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet stip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement as per specification & drawing shown in SSR Pt-II 2020 complete all as specified.

S & F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube fixed in opening as per specification & drawing shown in SSR Pt-II 2020 complete all as specified.

S & F of Butt hinges, 100mm size extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B-21 complete all as specified.

S&F aluminium, anodised, 150mm long barrel tower bolts of extruded section and fixed complete all as specified .

S&F aluminium, anodised handle 150mm size cast type anodised complete all as specified.

Cleaning/removing blockage of sewer line (SGSW/RCC/CI) of dia 100 mm including gully traps, grease traps etc.by removing all sludge, foreign materials and other deposit whatsover competely and making the line free from all obstacles of any description or in any position by roding, by pressure pump of any type or by using any mechanical equipments, manually or by puncher of sewage line and repair the same if required including taking off and re-fixing manhole covers including testing the flow of sewar line evenly, smoothly by filling water and removing the silt/sludge in covered van/trolly outside the MD land complete all as specified. Note : - The sewage line cleaned shall be measured one time only and the contractor shall be responsible to clean any subsequent blockage occured during entire contract period.

All as per Srl Item No 68 here in before but size of sewage line 150 mm dia complete all as specified.

De-watering from septic tanks of any size and any depth by suitable pumps and also removing of all wastes, semi solid or liquid of any description to outside MoD land complete all as specified.

De-sludging of manhole sludge (dry/wet), n exc. 1.50 m depth, individual manhole, desludging of septic tank any size, sludge removal manually including disposing of sludge by covered vehicle to a distance exc 500m but n.exc 3000 m & burried in excavated pit of adequate size including excavation and covering with earth from the existing septic tank of any depth, any capacity, in foul conditions, including taking & placing in position the manhole covers of any description, removal of sludge & solid contents to any place outside defence land and depositing complete all as specified.

De-sludging of manhole sludge (dry/wet) & septic tank exceeding 1.50 m depth, individual manhole, desludging of septik tank of any size, sludge removal manually including disposingl of sludge in covered vehicle to a distance exc 500 m but n.exc 3000 m & burried in excavated pit of adequate size including excavation and covering with earth from the existing septic tank of any depth, any capacity, in foul conditions, including taking & placing in position the manhole covers of any description, removal of sludge & solid contents to any place outside defence land and depositing complete all as specified.

Cleaning/removing blockage of WC, bath, kitchen, WHB, Gully Trap, includding P or S-Traps of any description, by rodding, pressure pumps of any description etc. by removing all sludge, foreign materails and other deposits whatsoever completely (working in foul condition with taking precautionary measures equipment as required or applicable and working on all working days including sunday) complete all as specified.

Dismantling posts or struts (wood, steel or R.C.C.) embedded in concrete, brick work, masonry, etc. any section, including taking out embedded portion and making good disturbed ground complete all as specified.

Dismantling fencing wire mesh, any type complete all as specified.

Dismantling barbed wire, any type complete all as specified .

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified.

Excavation in post holes each n. exc 0.50 cum, getting out in soft/loose soil and removing surplus material n. exc 50 m and making good disturb surfaces complete all as specified .

M&L for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in foundation of posts and struts, foundation, filling and mass concrete etc. complete all as specified .

M&L for PCC (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in benching, copings, bed plates, kerbs and the like including weathering slightly rounded or chamsfered angles, throating etc including necessary formwork complete all as specified.

S&F for Mild steel work of Fe-290 Gde E-165 as in angle iron fencing posts and struts & flat iron including cutting, tops to shape as directed, drilling holes, notching for wire etc. flat iron fillets (for securing wire mesh etc.) and 10 mm dia MS round bars horizontal including hooking & all necessary drilling, bolting or riveling etc. complete all as specified.

Supply only Chain link MS galvanised fencing, mesh size of any type but nominal dia of mesh wire not less than 3 mm, complete all as specified.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts etc. including provission of binding wire complete all as specified.

S&F for Mild steel screw bolts (machine made) of 10 mm dia and 50 mm long with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut complete all as specified.

M&L for Plain mild steel wire, galvanised class 3, in fencing including straining and fixing to wood, concrete or steel posts and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. complete all as specified.

S&F for Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified. (each line wire to be measured).

M&L for preparation of new steel and iron surface of any description and applying 2 coats of syntheltic enamel paint over a coat of red oxide primer complete all as specified.

M&L for preparation of new steel and iron surface of any description and applying 2 coats of syntheltic enamel paint over surfaces of any description, n. exceeding 10 cm in width or girth when unconnected with other painting or when painted in a different tint complete all as specified .

M&L for 100 mm thick Cement concrete (1:4:8) type D-2, using (40mm graded stone aggregate) as in sub floors/sub bases etc. complete all as specified.

M&L for 60 mm thick, machine pressed precast concrete interlocking paver block with grey cement and no pigment of any shape and size as approved by GE, confirming to IS 15658-2006, M-35 Grade laid over and including 25 mm thick sand cushion, complete all as specified.

M&L for machine pressed factory made PCC block (1:2:4) type B1 using 20 mm graded stone aggregate, as in kerb stone of size 300 x 300 x 150 mm set in cement mortar (1:4), complete all as specified.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed & pointed in neat cement slurry in floors with grey cement & pigment over and including 15 mm thick screed in CM (1:6), complete all as specified.

Dismantling (corrugated or semi corrugated) sheets in roof coverings, any type & description, complete all as specified .

Dismantling timber scantlings 40 Sqcm and over in section from unframed work complete all as specified.

Dismantling timber scantlings as in fillets, rails, posts, rafters, purlins, etc under 40 Sqcm in section from unframed work complete all as specified .

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections,hollow section) including distance pieces, cleats etc. conforming to Fe-410W Gde E-250 quality 'A' complete all as specified.

M&L for mild steel work as in wind ties for roof covering including securing bolts etc. including all necessary drilling, bolting or riveting etc and similar work conforming to Fe 290 Gde E-165 complete all as specified ..

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410W Gde E-250 quality 'A' complete all as specified..

Pre-painted galvalume alumimnium zinc coating GI based corrugated steel sheet 0.50 mm thick, sheeting of any colour having strength of 550 mpa as in roof covering etc, complete all as specified.

Pre-painted galvalume alumimnium zinc coating GI based plain steel sheet 0.50 mm thick sheeting of any colour having strength of 550 mpa as in roof covering etc, complete all as specified.

abhinav and company

M/s Ranaji Construction Co

Captainkomalchaharconstructions

GANGA CONSTRUCTION

M/S MAMTA CONSTRUCTIONS

PD GUPTA AND COMPANY

krishna Associate