For execution of civil work including electrical and plumbng installation under Development of Pond near Hansa Ki Johad Phase 2 Tughlaqabad Fort New Delhi

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2.8.1 All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : 7.1.1 Cement mortar 1:6 (1 cement : 6 coarse sand).

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin- charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 6.4.1 Cement mortar 1:4 (1 cement : 4 coarse sand)

CEMENT PLASTER (IN FINE SAND) 12 mm cement plaster of mix 13.1.2 1:6 (1 cement: 6 fine sand

CEMENT PLASTER (IN COARSE SAND) 13.4 12 mm cement plaster of mix : 13.4.2 1:6 (1 cement: 6 coarse sand).

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.3 Suspended floors, roofs, landings, balconies and access platform

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 5.22A.1 Mild steel and Medium Tensile steel bars

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 11.41.2 Size of Tile 600x600 mm.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. completeat all levels. 8.2.2 Granite stone slab colour black, Cherry/Ruby red 8.2.2.2 Area of slab over 0.50 sqm.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge 8.3.2 Granite Work

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 11.26.1 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. 13.85.3 With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. 13.42.1 Two or more coats on new work

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws with Door Kit Stainless Steel||Door kit| |Door Hardware| Gate Hardware| Door Accessories Kit| Front Aldrop| Back Latch| Two Handle| One Door Stopper & Tower Bolt.

Provision for providing and fixing of Float glass panes of nominal thickness 5 mm (weight not less than 12.50 kg/sqm) with Glass Putty (Adhesive) including Labour and all necessary tools

Provision for providing and fixing of electrical articles for providing electricity in house with all fitting including all charges etc complete Pvc Pipe 25mm

PVC Pipe Bend 25mm

Junction Box

FLUSH METAL BOXES 12M

FLUSH METAL BOXES 8M

FLUSH METAL BOXES 4M

FLUSH METAL BOXES 2M

FLUSH METAL BOXES 1M

Suntech 12 Way SPN Metal White Double Door Distribution Board MCB Box

PVC Insulated 6 mm Single Core Flexible Copper Wires & Cables Polycab /Crompton/Havells

PVC Insulated 2.5mm Single Core Flexible Copper Wires & Cables Polycab /Crompton/Havells

PVC Insulated 1.5mm Single Core Flexible Copper Wires & Cables Polycab /Crompton/Havells

PVC Insulated 1 mm Single Core Flexible Copper Wires & Cables Polycab /Crompton/Havells

Havells 12 M Cover Plate

Havells 8M H Cover Plate

Havells 4M Cover Plate

Havells Crabtree Athena 2M Cover Plate

Havells 1M Cover Plate

Polycarbonate Bulb Holder for Wall

Havells Crabtree Athena 5 Step Fan Regulator - 2 Module

Havells Crabtree Athena 6A Five Pin Socket

Havells Crabtree Athena 6A One-Way Switch (White)

Havells Crabtree Athena 6A-16A Three Pin Combined Shutter Socket

Havells Crabtree Athena 16A OneWay Switch with Indicator

Havells DHMGCDPF032 PVC Plastic 32A MCB DP C Curve (White)

Havells 32A Single Pole MCB, Multi, Standard (HA-SPMCB32)

Jaset Innovations Chipboard Screw with Saw Thread and Nylon Wood Dowel – White Zinc Plated – Flat Pozidriv Counter Sunk Head Assorted Small Sizes – Pack of 258 pcs

Havells Ventil Air DX 200mm Exhaust Fan (White)

Concealed Light led Light

Havells/Crompton Fan 3 Blades Ceiling Fan

Wall Mounting Fan (Havells V3 450mm Wall Fan)

12 Modular Wall Surface Electric Board with back plate

Plastic Wall/Desk Pvc Casing N Capping batten, For Electric Wire Installation

Labour Charges

Provision of Sanitary Work including all fitting & charges etc complete (A) Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: 17.3.1 W.C. pan with ISI marked white solid plastic seat and lid

(B) Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 8.3.2 Granite Work

(C) Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : 17.5.2 Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern

(D) Toilet Urinal white vitreous china flat portion for toilet with all with fittings, standard

(E) Polyethylene water storage tank with cover and suitable locking arrangement (2x2000 Liter)

(F) Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 17.28.2 Flexible pipe 17.28.2.2 40 mm dia

(G) Providing and fixing beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick

(H) Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 17.7.2 White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

(I) Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in charge.

Provision for Water Supply works including all fitting & charges etc complete. (A) Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing and provide single CPVC gate valve at starting of each point from Water tank. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 18.7.6 50 mm nominal dia Pipes (Mtr)

(B)Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing and provide single CPVC gate valve at starting of each point from Water tank. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 18.7.6 50 mm nominal dia Pipes (Mtr)

(C)Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing and provide single CPVC gate valve at starting of each point from Water tank. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 18.7.6 50 mm nominal dia Pipes (Mtr)

(D) Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing and provide single CPVC gate valve at starting of each point from Water tank. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 18.7.6 50 mm nominal dia Pipes (Mtr)

(E)Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing and provide single CPVC gate valve at starting of each point from Water tank. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 18.7.6 50 mm nominal dia Pipes (Mtr)

Provision for Drainage Works including all fitting & charges etc complete. (A) Provide and fixing of uPVC Waste Pipe 100 MM with necessary T, Corner and joints with chemical to fix and seal inclusive of all labours for surface dressing and leveling, covering

(B) Provide and fixing of uPVC Waste Pipe 100 MM with necessary T, Corner and joints with chemical to fix and seal inclusive of all labours for surface dressing and leveling, covering

(C)Repairing of old borewell and pump nearby site

Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 13.62.1 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture .

Removal of collected malwa from site to outside of Municipal limit by manually or Mechanical Transport tractor/trolly/ truck etc, to dumping ground by mechanically lead 5 km including loading, unloading and stacking approx.

Providing and fixing Stainless Steel Wall Mounted in Shape Rectangular in Plain Pattern/Style of Size/Dimension 600x450x1500 (W x H x L) Surface Finish Glossy with 4 Nos. of Tap at proper height for drinking water with all fitting and necessary parts as per design approved by ASI

Provision for providing and fixing 150 LPH Commercial RO Water Purifier Plant with TDS Adjuster Full Stainless Steel Body Works Upto 3000 tds 150 liter (150 LPH RO+UV+TDS WITH Auto Shut Off) (Purification Technology : RO : Type : Electrical, Purification Stage :Stage 1: 5 microns inline PP filter || Stage 2: Granule Active Carbon Filter ||Stage 3: Block Active Carbon Filter || Stage 4: RO Membrane ||Stage 5: Post Carbon Filter|| Stage 6: UV Light ||)(Max. duty cycle per day: 1500 Ltr, Suitable for Office) with 2 nos Voltas (The Voltas FSS4080 water cooler) Stainless Steel Water Cooler, 80 Liter, Silver.

Construction of granular sub-base (GSB) by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :4.1.8 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Random rubble masonry with hard stone (Pitching) in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like. 7.2.1 Cement mortar 1:6 (1 cement : 6 coarse sand)

Please Enable Macros to View BoQ information