SPL REPAIR TO ROOF TREATMENT, JOINERY, PLUMBING AND OTHER ALLIED WKS IN BLDG NO 179 (OR MD ACCN) OF BS MARG AND OTHER SANCTIONED WORKS OF AGE BR-II UNDER GE (EAST) LUCKNOW

Amount

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc. complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving not exc. 15 cm thickness below and above ground level complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position as in roofs, floors (other than ground floors) and similar works complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches , pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work using old size sub class- 'B' fly ash brick, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed.

M&L for brick work using old size sub class- 'B' fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed.

Dismantling brick tiles or terracing tiles, single layer of roofs complete all as specified and directed.

Striping out old roof treatment (tarfelt) from roof top and removing from site, complete all as specified and directed.

M&L PCC 1:2:4, type B1 using 20 mm graded stone aggregate as in roof kerbs / benching / coving and roof padding over roof surface /sunken treatment etc. rounded or chamfered on edges, complete all as specified and directed.

M&L for cleaning of all loose dirt and dust from roof surfaces and applying roof treatment as under :- (a) 10 mm thick plastering in CM (1:4) using 100 % coarse sand on roof / parapet walls with WPC @ 2 % by weight of cement. (b) Applying a coat of bitumenous primer @ 0.50 Kgs/Sqm on prepared surfaces and allow to dry. (c ) Applying a coat of hot blown bitumen VG-10@ 1.20 Kgs/Sqm over primer. (d) Supply and laying of 3mm thick (Minimum) polymeric water proofing membrane weighing not less than 3 Kgs/Sqm. (e) Applying a tack coat of hot blown bitumen grade VG-10@ 1.20 Kgs/Sqm . (f) Blinding with dry coarse sand @ 0.50 to 1.0 Kg /Sqm dusted over bitumen. (g) Supply and laying Sub class- 'B' Bricks tile 40 mm thick over and including 15 mm thick screed bed in CM(1:4) and jointing and pointing in CM (1:4) by mixing linseed oil @ 5 % weight of cement. (Note : The net area of water proofing treatment shall be measured without any extra allowance for laps & portion inserted in groove which shall be deemed included in the quoted rates.)

M&L for cleaning of all loose dirt and dust from roof surfaces and applying roof treatment as under :- (a) 10 mm thick plastering in CM (1:4) using 100 % coarse sand on roof / parapet walls with WPC @ 2 % by weight of cement. (b) Applying a coat of bitumenous primer @ 0.50 Kgs/Sqm on prepared surfaces and allow to dry. (c ) Applying a coat of hot blown bitumen VG-10@ 1.20 Kgs/Sqm over primer. (d) Supply and laying of 3mm thick (Minimum) polymeric water proofing membrane weighing not less than 3 Kgs/Sqm. (e) Applying a tack coat of hot blown bitumen grade VG-10@ 1.20 Kgs/Sqm . (f) Blinding with dry coarse sand @ 0.50 to 1.0 Kg /Sqm dusted over bitumen. (Note : The net area of water proofing treatment shall be measured without any extra allowance for laps & portion inserted in groove which shall be deemed included in the quoted rates.)

M&L for rendering 15 mm thick in cement mortar 1:4 on fair face of brick work of walls, mixed with water proofing compound (ISI marked) @ 2% by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement complete all as specified and directed. (Note : - Water proofing compound shall be measured and paid separately.)

M&L for rendering 10 mm thick in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces, finished even and smooth complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound, ISI Marked complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment of surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/ tint complete all as specified and directed.

M&L for applying two coats of wall care putty on walls overall thickness 3mm and finished surface even and smooth complete all as specified and directed.

M&L for complete removal of existing treatment of surfaces of walls and applying two coats of cement base paint of approved shade/tint inclung preparation of surfaces by using putty to make surfaces smooth complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling & applying three coats of white wash complete all as specified and directed.

M&L for preparation of old decorated plastered surfaces of ceilling and applying one coat of white washing on ceilling complete all as specified and directed.

M&L for preparation of old previously treated surfaces of walls and applying one coat of white wash on walls complete all as specified and directed.

M&L for applying three coats of white wash including preparation new plaster surface on wall complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing , removing and rubbish off the premises complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed.

S&F coloured non skid edge cut (joint free) ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in white or coloured cement to match laid over 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for non skid coloured ceramic tiles, joint free 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exc 0.38 sqm in floors with borders, incl over 15mm thick screed bed in CM 1:4 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floors complete all as specified and directed.

M&L for glazed ceramic tiles coloured 600x300x7 mm thick on vertical surfaces such as dado, skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick rendering in CM (1:4) complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18-20 mm thick over 15 mm screed bed (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and including granite polish on Kota slab stone complete all as specified and directed.

M&L for machine cut kota stone slab 18-20 mm thick on vertical surfaces such as dado, skirting etc. over 10 mm rendering in CM (1:4), laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and including granite polish on Kota slab stone complete all as specified and directed.

M&L for 50 mm thick PCC 1:3:6 type C-1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even and smooth complete all as specified and directed. (Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3) )

Forming construction joints 30 mm deep x 10 mm wide filled with sealing compound grade 'A' complete all as specified and directed.

M&L for 18-20 mm thick granite (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills, cooking platforms & like in cement mortar (1:4) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking plateform incl hole for gas pipe and other similar situation complete all as specified and directed.

Supply and laying of 3mm thick (Minimum) polymeric water proofing membrane weighing not less than 3 kg/Sqm over and including a coat of bitumen primer @0.50 kg per Sqm and 1.2 kg per Sqm bitumen grade VG-10 for sunken treatment complete all as specified and directed.

Taking down loose filling of aggregate in any form from sunken slab and refiiling after treatment complete all as specified and directed.

Taking up or down steel water tubing and connections of 15mm bore, fixed in walls, ceiling, floors, trenches etc. complete all as specified and directed.

Taking up or down steel water tubing and connections of 20mm bore, fixed in walls, ceiling, floors, trenches etc. complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement mortar 1:3 for concealed water tubing etc. and making good, cutting not exc 10 cm girth in brick walls complete all as specified and directed.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Fixing only 15mm bore tubes "medium grade " galvanised with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. (Note:- Old serviceable pipe shall be used obtained from taking down.)

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed

Fixing only 20mm bore tubes "medium grade " galvanised with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed . (Note:- Old serviceable pipe shall be used obtained from taking down.)

S&F vitreous china squatting pan (orissa pattern) water closet (white) of size 580X440mm with integral foot rests, 'P' & 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc including provision of PCC (1:5:10) type E2 in filling, making good to floor complete all as specified & directed.

S&F in repair PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed .

S&F in repair vitreous china wash hand basin, white, flat back of size 550 mm x 400 mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed complete all as specified and directed .

S&F in repair sink with drainage board made of stainless steel 0.8 mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 915 mm x 460 mm with bowl size 410 mm x 330 mm x160 mm including 32mm dia waste pipe of polyethylene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B-0 complete all as specified and directed .

S & F for stainless steel kitchen plate rack of overall size 750 mm x 600 mm and 250 mm deep, with partitions for small/large plates etc made out of stainless steel 0.63 mm thick fixed with rawl plug and CP steel screws complete, all as specified and directed.

S&F CP grating 125mm dia with waste hole complete all as specified & directed.

S&F CP grating 125mm dia without waste hole complete all as specified & directed.

S&F PVC connection 450 mm long suitable for 15 mm bore GI pipe including CP brass nuts on both sides, complete all as specified & directed.

S&F in repair long body 15mm bore bib tap, fancy type, chromium plated, cast copper alloy, with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified & directed.

S&F in repair CP angle valve, fancy type long body for 15 mm bore pipe with capstan head long screwed shank including cp cover plate complete all as specified & directed.

S&F in repair 15mm bore concealed type, stop valve cast copper alloy screwed down high pressure with capstan head and cup, screwed both ends for iron pipe or for union complete all as specified & directed.

S&F in repair 15mm bore pillar taps swan neck fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and flynuts, screwed for iron pipes, complete all as specified & directed.

S & F for PVC Corner shelf 300mm with chromium plated guard, fixed with brass screws and wooden/plastic cleats complete all as specified and directed.

S&F in repair CP brass tubular towel rail, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws complete all as specified and directed.

S&F 40mm bore PVC low density (LDPE) pipe of pressure 6kg/Sqcm fixed to wall or laid in floor complete all as specified and directed.

S&F in repair brass chromium plated shower rose 125 mm size without swivel joint including fixing to steel pipe of 15mm bore or union complete all as specified and directed .

Dismantling RCC/PVC water tanks and removing of capacity exceeding 250 litres & not exceeding 500 litres etc. complete all as specified and directed .

S&F 500 Litre capacity Rotational moulded polyethylene water storage tanks, white colour, Triple layered (cylindrical, vertical with closed top) hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete all as specified and directed.

S&F 20 mm ball valve high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20 mm bore, complete all as specified and directed.

S&F PVC coated 25mm dia Mild steel pipe as in curtain rods includin brackets and fancy type end knobs, complete all as specified and directed.

Demolition and breaking up or taking down PVC/AC/CI/SGSW 100mm bore pipe drain pipes, set in cement mortar including PCC haunching and bedding,complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed.

S & F PVC (SWR) floor trap of size 110/110mm, complete all as specified and directed.

S & F for 110mm PVC (SWR) WC connector bent type, complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend, any radius, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend, any radius with access door, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend, any radius, complete all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl, complete all as specified and directed.

Taking down chowkats or frames any type (without taking off shutters from the frames) refixing in same opening including welding/reveting complete all as specified and directed

Taking down chowkhat with shutter (without taking off shutter from the frame) and area exc 1.5 sqm but not exc 4 sqm each, complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area not exc 1.5 sqm each complete all as specified and directed.

Taking down shutter of any description exc 1 Sqm and not exc 2 Sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws complete all as specified and directed.

Taking down shutters of any description not exc 1.0 sqm each all complete all as specified and directed.

S&F 2nd class hard wood plain, solid, straight chawkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F mild steel holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Grade E-165 (Fe 290) including necessary welding etc. complete all as specified and directed.

M&L plain cement concrete cast in situ 1:3:6 type C1 using 20 mm graded stone aggregate as in copings, hold fast, back filling of pressed steel frame and other similar work water troughs and the like including weathering, slightly rounded or chamfered angles and throating etc including form work complete all as spcefied and directed .

S&F pressed steel frame for door with one or more rebates size 125x60mm including necessary fixing lugs, lock striking plates, hinges, hold fast etc. complete all as spcefied and directed

S&F pressed steel frame for door with one or more rebates size 105x60mm including necessary fixing lugs, lock striking plates, hinges, hold fast, etc.complete all as spcefied and directed

S&F for 30mm thick factory made flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides, complete all as spcefied and directed .

S&F for 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 (a) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.

M&L for mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing of Fe-410-0 (Gde-E-250) complete all as specified and diredted.

M&L in repair block board, 19/20mm thick, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame work as in cup board shutter/shelves/cabinet etc. complete all as specified and directed.

M&L for 0.9mm thick decorative laminate type 1, of surface finish, colour & pattern as approved, fixed with approved adhesive as per manufacturer's instruction complete all as specified and directed.

M&L magnet ball catcher for cup board shutters, complete all as spcefied and directed.

S&F continuous (piano) hinges miled steel bright finished or electro galvanised having 30mm width of flap when open complete all as spcefied and directed.

S&F for 100 mm long Hasp & staple, safety type, Stainless steel with mild steel hinges pin including bolt to hinges plate & fixed with screw complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; pannelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed together with solvent cement complete all as specified and directed.

S&F for factory made Solid PVC Door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F butt hinges of size 100 mm medium weight, stainless steel and fixed with SS screws complete all as specified and directed.

S&F aluminium handle, 150mm size, cast type, anodized (ISI marked) complete all as specified and directed.

S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed.

S&F 300 mm long mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, articles of 2nd class hardwood, articles not exc 200 cucm each complete all as specified and directed.

S&F mild steel framed work such as grills, guard bars, barred iron doors, cooler stand, framework of water tanks and similar works, conforming to Grade E-165 (Fe 290), including welding etc. complete all as specified and directed.

S&F steel window with side hung shutters including box type hings with steel handles and steel peg stay, complete with galzing bar, dovetailed or welded complete all as specified and directed.

S&F in repair kitchen cabinet shutter with frame including shelves, drawer made of solid PVC Block board 18/19mm thick both sides decorative face having smooth outlet integral skin are made and shall be fixed to walls using required size sheet metal screw and solvent adhesive vertical and horizontal profile made of PVC 18/19mm solid board profile complete all as specified by manufacturer's instruction complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified and directed.

S&F in repair 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified and directed.

S&F 3mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire, staples complete all as specified and directed .

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire, staples complete all as specified and directed .

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of red oxide complete all as specified and directed.

M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint complete all as specified and direced.

M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc. complete all as specified and directed..

M&L for cement concrete (1:3:6) type C1 using 20 mm graded crushed stone aggregate as in surface channels, drains, coping and benching including necessary formwork whrever required complete all as specified and direced. (Note : Forming fair finished channel for drain using extra cement shall be measured and paid for separately.)

M&L for 40mm thick PCC 1:2:4, type B-1 using 20mm graded crushed stone aggregae as in floors, finished even and smooth using extra cement, complete all as specified and directed.

M&L for 60mm thick pressed precast concrete interlocking paver block reflective type, rubber moulded coloured of M-35mm grade over 25 mm thick sand cushion as in floors complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed .

M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in cover slab, shelves and similar articles set in CM 1:4 complete all as specified and directed. (Note:- Reinforcement shall be measured & paid separately .)

M&L for TMT bars 10mm dia and over cut to length, bent to shape required including cranking and binding with Mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F rolled mild steel work in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering,cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

M&L for cement concrete type B-1 1:2:4(20mm graded aggregate) as in lintel,cills, steps , seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

S&F powder coated aluminum Window sliding type three track with glazed and gauzed shutter (incl stainless steel wire cloth 0.36 mm nominal dia and 1.40 mm apreture and 5 mm thick plain glass) on wheel consisting frame of size 100 x 44 (sliding shutter consist of suitable size of section as specified and directed) with locking arrangement as approved fixed with rubber gasket and aluminum beading etc including necessary cutting hole in wall complete all as specified and diredted. (Note-Glass for glazed shutter and SS wiremess for wired shutter are included in the item. )

S&F aluminium anodised partition wall with 5.50 mm thick glass and 38 mm x 63 mm size anodised aluminium section frame work fixed with aluminium and rubber beading and fixing arrangement for fixing the framework to wall/floor complete all as specified and directed (Note-Glass is included in the item. )

M&L for false ceiling with 4 mm thick E-board "Make-Everest" white prelaminated set embossed reinforced designer ceiling board of approved texure fixed with GI imposed grid frame work of size not more than 600 x 600 mm having 24 mm wide T- section, runner made of 0.33 mm GI sheet and angle made of 0.45 mm GI sheet, suspended with 4 mm dia GI wire including two coat of oil bound distemper complete all as specified and directed

Cutting holes in brick walls built in cement mortar or lime mortar and stone walls built in lime mortar for inserting holdfast and making good dismantled portion in cement concrete 1:2:4 Type B-1, depth of embeded portion of hold fasts or lug measured from the face of the jamb into the wall exc half brick but not exc. one brick complete all as specified and directed

S&F steel window with side hung shutters including box type hings with steel handles and steel peg stay complete without glazing bar, dovetailed or welded complete all as specified and directed.

S&F steel ventilators with top hung shuers including hinges, steel handle and steel peg stay complete with glazing sash, dovetailed or welded including taking down old window panel complete all as specified and directed.

Taking down copper / aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or taking credit and making good the disturbed surfaces of walls, floors, etc. complete all as specified and directed .

M&L for point wiring for one light / fan point controlled by one switch.with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth duly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and replacement of sunk zinc coated pressed steel terminal box of 1.60mm thick with 3 mm thick plastic laminated sheet top cover, brass screws, cup washers etc and making good to the disturbed surfaces to match the existing complete all as specified and directed

All as per srl item No 131 here-in-before but for one bell / buzzer point controlled by one bell push button on the same board with other switches or independent with cable 1.5 Sq mm size complete all as specified and directed .

All as per srl item No 131 here-in-before but for one 3 pin socket outlet, 05 Amps, independent with cable 1.5 Sq mm size complete all as specified and directed .

All as per srl item No 131 here-in-before but for one 3 pin socket outlet 05 Apms point on the same board with other switches with cable 1.5 Sqmm size complete all as specified and directed .

All as per Serial Item No 131 here-in-before but for one 3 pin socket outlet, 15 Amps, independent with cable 2.5 Sq mm size complete all as specified and directed .

S&F switch piano flush type, single pole, one way, 05 Amp complete all as specified & directed.

S&F bell push, flush type, 05 Amp complete all as specified & directed.

S&F socket outlet 2 in 1, 3 pin, 05 Amps complete all as specified & directed.

S&F switch socket combination 2 in 1, 3 pin, 05 and 15 Amps, flush type, universal complete all as specified & directed.

S&F stepped type, electronic fan regulator, flush and socket type on the existing phenolic laminated sheet humfree 2 module ISI marked etc as required complete all as specified & directed.

S&F buzzer, Ding Dong, AC, 230 volts, single pole complete all as specified & directed.

S&F lamp holder, PVC / Polycarbonate type with back plate suitable for batten fittings complete all as specified & directed.

S&F LED bulb with base B22d of 9 Watt 900 lm suitable for batten/angle holder complete all as specified and directed.

S&F in replacement of decorative wall mounting type LED light fitting, 1 x 15 Watt, 230 Volt made up of Polycarbonate including shade, lamp holder, 10 Watts LED lamp B22 CDL etc and all accessories pre-wired including connecting up complete all as specified and directed. Make : Philips, Cat No : 30575 (Comet) or equivalent in Havells/Bajaj as approved by GE.

S&F in replacement of integrated LED bulk head fitting 10 Watt, 6500K with IP 65 protection comprises of high pressure die cast aluminium housing, polycarbonate cover, etc complete all as specified and directed. Make : Crompton, Cat No : LBHP-10-CDL or equivalent in Havells, Cat No : RUGBYNEONFT10WLED760SSYMBOPC, PHILIPS Cat No : WT202W LED6S CW PSU S2 PC .

S&F in replacement of single side connection LED T8 tube light rod 20 Watt, 6500K of four feet long into and including LED tube light fixture of four feet long with T8 push fit type holders, connector block, end caps, etc including connecting up complete all as specified and directed. Make :- Crompton, Cat No : IGP131LT8-16& LT8-20-865-2 or equivalent in Havells/Bajaj as approved by GE.

S&F in replacement of LED security light fitting 45 watt, 5700K with IP 66 protection comprises of a pressure die cast aluminium housing, heat resistance toughened glass, LED lenses, surge protector, electronic driver, etc and all accessories pre-wired including connecting up with PVC insulated copper conductor cable 1.5 Sq mm, 3 core as required for connections and 32 mm bore light grade G. I. tube mounting bracket of 1.5 metre in length, bend to shape at 140 degree in ‘L’ shape and fixed to wall by means of 02 nos. of 40 x 5 mm flat iron clamps, nuts, bolts and washers etc complete all as specified and directed.

Supply and fix ceiling rose, 3 phase / PVC / polycarbonate, isolated body complete all as specified directed.

M&L for sub main wiring with 04 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 04 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed.

M&L for sub main wiring with 06 sqmm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 06 Sqmm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed.

S&F in replacement of industrial type SPN enclosure with a two pin and earth plug and socket complete with and including MCB, SP, AC, 240 volt of 20 Amp, 'C' curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

S&F in replacement of sheet metal enclosure distribution board, single pole and neutral, AC, 240 volt, 08 way, with 200 Amp rated copper bus bar and metal door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

S&F in replacement of sheet metal enclosure distribution board triple pole and neutral (VTPN), AC, 440 volt, 04 way with 200 Amp rated copper bus bar and metal door with IP 54 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed and comprising of the following :- (a) MCCB, 125 Amp, 04 pole, AC, 415 Volt of 16 KA breaking capacity complete - 01 No. Make :-Legrand, Model : DPX 160, Cat No. 4200 16 or equivalent in Hager, Cat No : HDA126Z or Schneider, Cat No : LV516312 (b) MCB, SP, AC, 240 volt of 06 to 32 Amp, "C" curve, 10 KA breaking capacity - 12 Nos. Make :-Legrand, Cat No. 5077 50 & 5079 38 or equivalent in Hager Cat No : VYV04PM & VYV00E or Schneider Cat No : A9HVD04M & A9HVDXXWB

S&F in replacement of MCB, SP, AC, 240 volt of 06 to 40 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed. Make:- Legrand Cat No. 408587 to 4085 95 or equivalent in Hager Cat No. NCN106N to NCN132N or Schneider Cat No. A9N1P06C to A9N1P32C.

S&F in replacement of MCB, DP, AC, 240 volt of 40 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Taking down electric meter of any capacity and refixing with connection complete all as specified and directed .

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in electrical plate No 3 on serial page No 497 of SSR part I - 2009 and connected to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20 mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40 mm thick in PCC 1:2:4 type B-1 duly reinforced with MS bars 6 mm dia at the rate of 75 mm center to center both way with 12 mm dia lifting handle and pit / chamber in PCC 1:3:6 type C-1, angle iron 40mmx40mmx3mm frame for pit cover including testing on completion complete all as specified and directed.

S&F in replacement of recessed mounted 2'X2' LED ceiling light fitting 36 watt, 6500K with IP 20 protection comprises of CRCA housing, high efficiency diffuser cover, electronic driver etc and all accessories pre-wired including connecting up complete all as specified and directed. Make: Cromption, Cat No. LCPL-36-CDL(2X2) or equivalent in Havells Cat No. VENUSNEOHE2X2PLR36WLED8XXS or Philips Cat No. RC380B LED36s-6500G4 L60W60 PSU OD OC.

S&F 10 sqmm 2 core aluminium unarmoured flame resistant PVC flat cable, ISI marked complete all as specified and directed.

S&F ceiling fan hook in existing truss including 3 feet down rod complete all as specified and directed.

G D SINGH AND CO

M/S SWATI CONSTRUCTION

ANIL CONSTRUCTION

M/S Reliance Construction

M/s Durga Construction Company

M/S S&R Construction