Up-gradation of Industrial Estate IID Centre SICOP, Govindsar Kathua (with three years maintenance of Bituminous works)

Amount

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas(exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth to the diposal site including all leads of lifts as directed by the Engineer-in-charge (All kinds of soil).

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth to the disposal site including all leads & lifts as directed by the Engineer-in-charge (All kinds of soil).

Banking excavated earth in layers not exceeding 20cm in depth, breaking clods, watering, rolling each layer with 1/2 tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc. including all leads & lifts complete. All kinds of soil.

Providing and laying Dry stone pitching (any thickness) including cost of stones on Horizontal

Providing and laying WATER BOUND MACADAM, with nallah stone aggregate and binding material including screening of 13.2mm size and stone dust; sorting spreading to template and consolidation with Power Road Roller of 8-10 tonne capacity complete. (Finished work including material and labour) 63mm to 45 mm size of stone aggregate including stone screening of size 13.2mm) including all carriages complete job.

Providing and laying WATER BOUND MACADAM, with nallah stone aggregate and binding material including screening of 11.2mm size and stone dust; sorting spreading to template and consolidation with Power Road Roller of 8-10 tonne capacity complete. (Finished work including material and labour) 53mm to 22.4 mm size aggregate with 11.2mm size screening) including all carriages complete job.

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm) to wet mix macadam (WMM) specification including premixing the material with water at OMC in Mechanical mix plant, carriage of mixed material by tipper at site, for all leads and lilfts, laying in uniform layers with mechanical paver finisher in sub-base/ base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired denisty, complete as per specifications and directions of Engineer-in-charge including loading/unloading all carriages complete job

Providing and laying 50 mm thick (Compacted) premix bituminous macadam base course with stone aggregate of quality size and grading as specified in latest MORT & H specifications and staight run bitumen of VG-30@ 4% by wieight of total mix including Hot mixing of stone aggregates and bitumen in Hot Mix Plant, Transporting mixed material to the site and laying with paver finisher as per required profile including cost of priming coat/ tack coat and filling patches/ pot holes with BUSG/ Bituminous Macadam in required level and grade rolling with roller 8 to 10 tonne capacity to achieve the required compaction and density. All complete including cost of bitumen and all sort of taxes.

Providing and laying 25 mm thick open graded premix carpet with specified graded stone aggregates for wearing course including loading of aggregates with FE loader and hot mixing of bitumen with filler and stone aggregates in hot mix plant, transporting and mixed material by tippers to paver at site of work and laying the mixed material with mechanical paver finisher to the required level and grade, rolling with power road roller to achieve the desired density and compaction including cost of priming coat/ tack coat and finally finish the surface with seal coat (Bitumen used shall be VG-30 and grading of mix shall be as per the relevant clause of MORT&H) All complete including cost of bitumen and all sort of taxes

Providing and applying 2.5 mm thick road marking strips (retro-reflective) of specified shade/colour using hot thermoplastic meterial by fully/semi-automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.

Providing and laying in position cement concrete of specified grade including curing ,centring and shuttering. All work upto plinth level with 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size including all carriages complete job.

Providing and laying in position cement concrete of specified grade including curing, centring and shuttering. All work upto plinth level with 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) including all carriages complete job.

Reinforced cement concrete work in beams, suspended floors, roofs, RCC drains, walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but including cost of centering shuttering, finishing and reinforcement 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) including curing all carriages complete job.

Providing and laying in position cement concrete of specified grade including curing, centring and shuttering. All work upto plinth level with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) including all carriages complete job.

Providing and laying in position cement concrete of specified grade including curing, centring and shuttering. All work upto plinth level with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including curing all carriages complete job.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete .Thermo Mechanically Treated bars of grade Fe-500D or more (make Jindal Panther, TATA TISCON, SAIL) including all carriages complete job.

Providing and fixing of 100 mm dia G.I pipe. (medium)

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand) including all carriages complete job.

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in Cement mortar 1:4 ( 1 cement : 4 coarse sand) including all carriages complete job.

12mm Cement plaster of mix 1 : 4 ( 1 cement : 4 fine sand) including curing & all carriages complete job.

15mm Cement plaster on the rough side of single or half brick wall of mix 1 : 4 ( 1 cement : 4 fine sand) including curing and all carriages complete job.

6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand) including curing and all carriages complete job.

Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground With cement mortar 1:4 (1 cement : 4 fine sand) including curing and all carriages complete job.

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete including all carriages complete job.

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, including the cost of nosing of steps etc. complete .50 mm thick with 20mm nominal size stone aggregate including all carriages complete job.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, including all leads & lifts complete job.

Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete job.

Demolishing cement concrete manually/by mechanical means including disposal of material to the disposal site as per direction of Engineer-incharge 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/by mechanical means including stacking of steel bars and disposal of unserviceable material to the disposal site as per direction of Engineer-in-charge

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground as directed by the Engineer-in-charge.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete including all carriages complete job.

Finishing walls with water proofing cement paint of required shade (two or more coats applied @ 3.84 kg/10sqm)

White washing with lime to give an even shade (three or more coats)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work.

Painting (one or more coats) with black Japan paint of approved brand and manufacture to give an even shade.

Distempering with dry distemper of approved brand and manufacture (one or more coats) and of required shade on old work to give an even shade.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade (two or more coats) over and including priming coat with water thinnable cement primer

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.

Finishing walls with acrylic smooth exterior paint of required shade (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm)

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 2 mm thick

Providing and fixing sign boards with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded size upto 20 mm nominal size) size 1'-6'' X 2'-0'' below ground level in different lanes made of square M.S pipes of size 50 X 50 X 3.60mm M.S Sheet 18 Guage including Radium Paints & computerized writing of radium alphabets Paints etc. all job complete at site including labour for fixing, welding etc. size of sign board 1'-6'' X 2'-0'' as directed by the Engineer-in-charge.

Providing and fixing M.S tree guard 45 cm square in plan, height 1.20 meter above ground level and 0.40 meter below ground level. The vertical members shall consist of four nos. angle iron of size 25x25x3 mm, 1.6 m long, one at each corner and 8 nos flat iron of size 25x3 mm, 1.2 m long. The vertical members shall be welded to 4 nos. 25x6 mm M.S flats placed horizontally around the vertical members of the cage. One name plate of 1 mm thick M.S sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD /PWD/any other approved name. The tree guard shall be fixed to the ground by making suitable holes and by embedding four corners leg in the ground, including refilling the earth, compaction etc. complete. The tree guard shall be painted with two more coats of synthetic enamel paint of approved brand and or more coats of synthetic enamel paint of approved brand and manufacture over a coat of primer complete job.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement: 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete job.

Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.110 mm diametre complete job.

Providing and fixing on wall face un-plasticized - PVC moulded fittings/ accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion 110 mm bend complete job.

Providing and fixing un-plasticised -PVC pipe clips of approved design to un-plasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete job (110 mm dia)

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using flats 30x6mm for diagonal braces and central cross piece

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 complete job.

Inside size 90x80 cm and 60 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 complete job.

Providing and laying non-pressure of specified class R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement: 2 fine sand) including testing of joints etc. complete. 900 mm dia. R.C.C. pipe

Engaging labours for pipe layout

Providing and fixing P.V.C low level flushing cistern with manually controlled device (handle lever) including seat coversconforming to IS : 7231, with all fittings and fixtures complete 10 liter capacity -White

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete 32 mm dia.

Providing and fixing PTMT grating of approved quality and colour. 100 mm nominal dia

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931

Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc 20 mm dia. nominal bore

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge

Providing and fixing G.I Pipes complete with G.I fittings excluding trenching and refilling etc. external work 80mm dia.

Providing and fixing C.I sulice valve with cap complete with bolts, nuts, rubber insertions etc. complete job. 100 mm dia

Providing and fixing of Gun-metal non-return valve of approved quality (screwed end) 80 mm dia. Complete job.

Providing and fitting of 80 mm dia G.I pipe. The job includes Flanging of 80 mm dia (2'') GI (B class) column pipe (Parkash Surya/ Jindal). By cutting 6 mtr. Length GI pipe on lathe and marking 3 mtr. Length pieces Providing and fitting of MS flanges 12 mm thick to each 3 mtr. Length pipe on both sides. The flanges are to be finished properly. Manufacturing and facing of both the surfaces is to be done in such a way that by inserting a rubber sheet in between two flanges and tightening the nuts and bolts completely, leak proof joint is made. Each flange is to be provided with 4 No. of equidistant holes of requisite dia. The job also includes welding of flat iron strips at each end for giving extra strength to the flanged joints and providing of 2 No. grooves on each flange on Opp. Side for subermisble cable. Painting of all the pipes by cleaning of surface with emery paper, removsl of rust if any, providing one coat of anti corrosive enamel primer and finally one coat of super black enamel paint. The job includes carriage of all the pipes duly painted and flanged at both ends to the site work including loading and unloading of pipes.

Installation, testing and commisioning of 3000-4000 GPH x 80-100 mtrs 20 HP. Head submerisble pumpset (KSB/ Kirloskar/ crompton/ any reputed make) at Tubewell by way of fabrication, providing and fitting of 1 No. U-shaped tie rod/ clamp to be fabricated out MS flat that is to be fitted with submerisble pump with the help of heavy duty bolts and nuts welded on both sides of the clamp. The Job also includes fabrication of 1 No. expander/ reducer nipple of NRV of required size to be fabricted out of MS plate threaded at one end and falnged at the other end. Fitting of reducer/ exapnder nipple with 100 mm dia. Column pipe at one end with flange joint and with the discharge outlet (NRV) of the submersible pump at other end. The job includes cost of material and labour charges. Lowering of submersible 10,000 GPH x 100 Head submersible pumpset in the Tubewell. The job includes cost of material such as rubber sheets, nuts an bolts and labour charges. It also includes carriage of pump set. Making connections with the panel and testing on full load at site. Complete Job.

Providing and fitting of 10 sq. mm cable - 160 mtrs. (phinolex/havels/any reputed make) by means of making of connection of one end of the submerisble cable with motor by way of patching in order to make joint water proof and lowering along with pump, motor and column pipes into the tube well. Connecting other end of the submersible cable with panel after providing and fitting of copper thimbles, crimping and insulating properly. Testing the pumping unit in full load at site. The length of cable can increase or decrease as per site conditions. Complete job includes cost of mterial and labour charges.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable size G.I box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. Wire Make: Anchor/ Havells/ Vguard/ Polycab Conduit Make: AKG/Anchor/Finolex/Polypack

Group A

Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/recessed steel/ PVC conduit including dismentaling as required. Wire Make: Anchor/Havells/Vguard/Polycab Conduit Make: AKG/ Anchor/Finolex/Polypack

Group A

Wiring for group controlled (looped) light point/ fanpoint/ exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group A Wire Make: Anchor/Havells/Vguard/Polycab Conduit Make: AKG/Anchor/Finolex/Polypack

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.(Make: Havells/ABB/Legrand/Anchor/vguard/L&T/Schneider)

5/6 amps switch

3 pin 5/6 A socket

15/16 A switch

6 pin 15/16 A socket

Telephone socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.(Make: Havells/ABB/Legrand/Anchor/L&T/Schneider)

3 Module

4 Module

6 Module

8 Module

12 Module

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.(Make: Havells/ ABB/ Legrand/ Anchor/Schneider/Vguard)

supply & installation of pre-wired, fluorescent fitting / compact fluorescent fitting of T5 batten (20 watt) complete with all accessories. as required.(Make: Havells/Wipro/Crompton/Philips/Panasonic)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. (Make: AKG/ polycab/ Anchor/Polypack)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.(Make: VGuard/ Havells/ABB/anchor)

SINGLE POLE

SINGLE POLE AND NEUTRAL

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.(Make: VGuard/ Havells/ABB/Anchor))

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.( Make: Finolex/anchor/Vguard/Havells)

2 x 2.5 sq. mm

2 x 4 sq. mm

1 x 1.5 sq. mm

Supply, installation,testing and commissioning of Inverter 850 va with 01 no battery 150ah including trolley complete with all accessorries as required.( Make: Microtek/Luminous/Exide)

Supplying and fixing PVC batten/ angle holder including connections etc. as required( Make: ISI)

Supply & fixing of LED Bulb of 9/10 watt.(Make: Wipro/orient/panasonic/philips)

Supply & fixing of single phase MCB DB ( 6 way- single door) complete with all accessories as required (Make: Anchor/ Havells/ Phillips/ crompton/ Siemens)

Supply & fixing of Pvc type 2pole MCB cover complete with all accessories as required.( Make: ISI)

Suppy, installation, testing and commissioning of 2 core , 16 sqmm aluminium armoured cable ( to be useed as main service line) complete with all accesssories as required.( Make: Havells/ RR cabel/Finolex/kei/ Apar ind/ Grandley)

Suppy, installation, testing and commissioning of surface/ recessed type 2 ft x 2 ft LED type Panel light complete with all accessories and as desired by EIC.( Make: philips/Jaquar/Havells/Panasonic)

M/s Sujan Singh

TBA INFRASTRUCTURE PVT LTD