PROVN OF GUARD ROOM WITH ATTACHED TOILET BATHROOM ALONG A SECT-III BOUNDARY AT SRI GANGANAGAR MIL STN

Site Clearance & Surface dressing not exceeding 15 cm deep in soft / loose soil.

Removing excavated soil (hard dense soil) to a distance n exc 50m, depositing where directed at a level n exc 1.5m above the starting point.

Earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m in all kind of soil complete all as specified.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dence soil.

All as per item No 2 above but exc 1.50 in depth but n.exc 3.0 exc

M&L for 'Anti termite treatment (Pre treatment) treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M&L for 'Anti termite treatment (Pre treatment) Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete alla s specified and directed.

M&L for 'Anti termite treatment (Pre treatment) Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete alla s specified and directed.

M&L for providing cement concrete 1:4:8 type D2 (Using 40mm graded stone agg) in foundation, mass concrete and fillings.

M&L for providing reinforcement cement concrete,Design Mix M-25 (using 20mm graded stone agg)as in footing, foundation,beams, plinth beams, base for columns and mass concrete etc.

M&L for providing reinforcement cement concrete,Design Mix M-25 (using 20mm graded stone agg) as in columns complete all as specified and directed.

M&L for providing reinforcement cement concrete, Design Mix M-25(using 20mm graded stone agg) as in beams, cantilevers, bressumers, lintel over 1.5m span all as specified.

M&L for providing reinforcement cement concrete in Design Mix M-25 (using 20mm graded stone agg) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified.

M&L for providing reinforcement cement concrete, M-25 (using 20mm graded stone agg) as in Chajja all as specified.

S&F mild steel TMT bars Fe 500D/550D, 10mm dia and over , cut to length, bent to shape requred, including crancing bending and binding with mild steel (anneal) wire not less than 0.90mm dia.

S&F mild steel TMT bars Fe 500D/550D 6 to 8 mm dia , cut to length, bent to shape requred, including crancing bending and binding with mild steel (anneal) wire not less than 0.90mm dia.

S&F mild steel TMT bars 6 to 10mm dia a as in stirrups, spacers and binders.

Form work to side of concrete in fdns, footing base, base of columns, side and soffits of plinth beam and simillar work.

Form work Form work flat rough finished surfaces of concrete to sides of columns.

Form work to side and soffits of floor beams. Lintel beam, roof beam , landing, waist slabs, chajja railing and similar work.

Form work flat rough finished surfaces of concrete to soffits of suspended slabs such as roof slabs, floor slabs landings and similar works not exc 200mm thick (Horizontal or slopping).

Form work flat rough finished surfaces of concrete to Chullah hood Chajja, troughs and similar items including edges.

Form work rough finished surfaces of concrete to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls and similar works exc 10cm but n. exc 20cm wide.

M&L 15mm plaster in CM 1:3 in roof top while the concrete is green with approved water proofing compound in proportion as recommended by the manufacturer (Waterproofing compound measured and paid saperately). complete all as spd and directed.

Supply only integral liquid water proofing compound.

M & L brick work with Fly Ash old size bricks straight or curved on plan exceeding 6.0m mean radius built in cement mortar 1:6 all as specified and directed by Engineer – in – Charge.

M&L for providing old size Burnt clay bricks Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as spd and directed by Engr in Charge.

M&L for Burnt clay old size Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as spd and directed by Engr in Charge.

M&L for Polythene film, 150 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m to horizontal or vertical surfaces complete all as specified and directed.

M&L hardcore of gauge n.exc. 63mm deposited, spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface for plinth protection

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm.

M&L for Rendering 15mm thick in CM 1:4 in two layers (1st layer 10mm th and 2nd layer 5mm th with Water proofing compound) on other than fair faces of brick work finished even and smooth without using extra cement complete all as specified and direceted by Engr in Charge. Note: WPC shall be measured and paid seperately.

M&L for Rendering 15mm thick in CM 1:6 on fair faces of brick work finished even and smooth without using extra cement complete all as specified and direceted by Engr in Charge.

M&L for rendering 5mm thick in cement mortar 1:3 on ceiling finished even and smooth without using extra cement as per manufacturer instruction.

M&L providing cement concrete 1:4:8 type D2 (Using 40mm graded stone agg) , 100mm thick as in sub base in floor/paving etc.

M&L providing cement concrete 1:2:4 type A1 (Using 20mm graded stone agg) , 25mm thick as in sub base in floor/paving etc.

Prepration of New external plastered wall surface and applying complete all as specified complete all as specified and directed by Engineer-in-charge of the following :- (a) Applying 1mm thick wall care putty on wall surface and smoothening the surface prepatory to paint. (b) Applying 02 coats of exterior emulsion paint (light shade) with highlighter of any approved shade, @ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using brands of emulsion and primer complete all as specified and directed.

Prepration of New internal plastered wall/Ceiling surface and applying complete all as specified complete all as specified and directed by Engineer-in-charge of the following :- (a) Applying 1.5 mm thick wall care putty on wall surface and smoothening the surface prepatory to paint. (b) Applying 02 coats of interior emulsion paint (light shade) @ 10 sq.m/litre/2 coats by using roller/brush to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using brands of emulsion and primer complete all as specified and directed.

M&L Premium quality non skid ceramic coloured tiles 7-8 mm thick, area of the tile exceeding 0.11 Sqm but not exc 0.18 Sqm in floor etc, set and jointed in neat cement slurry and joints to be filled with epoxy grout to match complete all as spd directed.

M&L Machine cut kota stone slab flooring 20-22 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed. Note : 100mm wide white makhrana marble strip of 16-20mm thick to be laid in design directed by Engineer-in-Charge.

M&L Premium quality coloured Glazed ceramic tiles in vertical surface 600x300x7-8mm thick set and jointed in neat cement slurry and joints to be filled with epoxy grout and pointed to match including rendering 10mm thick in CM 1:3 as a backing coat.

M&L 75 mm thick cement concrete type C-2, 1:3:6 (40 mm graded aggregate) finishing cement concrete surface even and smooth without using extra cement as in plinth protection complete all as spd and directed. Note : Rastes included for forming expansion joints of span n.exc 3m and joints should be filled with bitumen mastic grade B.

S&F Factory made single extruded laminated WPC (Wood Polymer Composite) solid decorative type flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Square Tower Bolt 200mm long, dia 10mm - 2 nos per leaf (b) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos. perleaf (c) Stainless Steel (304 Grade) 100mm size and medium weight butt hinges - 3 nos per leaf complete all as specified and directed by Engineer-in-Charge.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified & directed.

S&F Factorymade Mild steel windows/ ventilators n.exc less than 1.20mm thick box type (primer coated) ERW hollow 'P' section of size 60mm x 25mm single rebated comprises of glazed and skelton shutter ERW section 50mm x 20mm and 1mm thick and two open able leaf consisting two Nos sash bar of 'T' section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box 'T' section of size 60mm x 25mm and 1.25mm thic. Each window included following fittings welded to failed shutter :- (a) Holdfasts 150mm long 12mm x 3mm made to shape - 04 Nos per window. (b) Handle of Z section 20mm x 25mm, 100mm long - 1 No of leaf. (c) MS tower bolt 150mm long 02 Nos per leaf. (d) 'Z' section 20mm x 25mm, 100mm long stopper- 01 No per Leaf. (e) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 Nos per leaf. (f) MS paintal hinges of size 75mm x 12mm - 02 Nos per leaf. (g) Fabrication and fixing arrangment complete.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as specified and directed.

M&L for 4.0 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exceeding 0.5 Sqm in each panes.

S&F 300 mm long Stainless steel sliding door bolts, plate type, with bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified.

S&F 200 mm long Stainless steel barrel tower bolts,, with SS bolt dia n less than 10mm complete all as specified.

S&F 100 mm long long medium weight stainless steel butt hinges fixed with rus proof/SS screws.

S&F premium quality Stainless steel handles, D type of 250 mm long complete all as specifed and directed.

S&F floor door stopper of stainless steel body and double legged, tongue with hard drawn steel spring 140 mm size.

M&L for providing two coats of painting with synthetic enamel paint over a coats of red oide primer on new steel surface after preparation complete all as specifed and directed.

Supply and fixing sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, flat edge (matt finish) bowl size 600 mm x 400 mm x 220 mm including waste coupling and waste pipe complete all as specifed and directed.

M&L granite (telephone black) work 16 to 20 mm thick (table rubbed and polished) in cooking platforms/counters/vanities/skirtings/Window frames etc like in cement 1:4 including pointing in white cement (1:2) using marble dust with dmixture of pigment to match with shade of granite complete all as specifed and directed.

S&F 15 mm dia brass CP wall mixer 3 in 1 for mixing hot & cold water screwed down for iron pipe with spouts to shower and fixed complete all as specifed and directed.

S&F rotational moulded polythlene water storage tanks Triple layered (cylindrical vertical with closed top) hoisted and fixed in position of 1000 Ltrs capacity including ball valves 20 mm size, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed fro iron pipe and fixed and 20 mm nipple suitable for HDPE water tank complete all as specifed and directed.

S&F rotational moulded polythlene water storage tanks Triple layered (cylindrical vertical with closed top) hoisted and fixed in position of 500 Ltrs capacity including ball valves 20 mm size, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed fro iron pipe and fixed and 20 mm nipple suitable for HDPE water tank complete all as specifed and directed.

S&F PVC connection 15mm size, 450mm long with PTMP nuts both side.

S&F single lever extended basin/sink mixer cast copper alloy, chromium plated 15mm dai of bore complete all as specified and directed by Engr-in-Charge.

S&F 75 mm dia PVC (SWR) floor trap/multifloor trap, plain with grating including jointing with solvent cement fixed in cement concrete type B-1 (1:2:4) complete all as specifed and directed.

S&F for 125/110 mm dia PVC (SWR) floor trap/multifloor trap/Gully trap, plain with grating including jointing with solvent cement fixed in cement concrete type B-1 (1:2:4) complete all as specifed and directed.

S&F uPVC (SWR) pipes, single socketed, in any length, with rubber rings 75 mm dia laid in trenches in floors or on walls complete all as specifed and directed.

S&F uPVC (SWR) pipes, single socketed, in any length, with rubber rings 110 mm dia laid in trenches in floors or on walls including complete all as specifed and directed.

OVERLAY- PU BASED ELASTOMERIC LIQUIED MEMBRANE SYSTEM FOR EXPOSED ROOF : Providing and applying polyurethane liquid roof waterproofing with improved water ponding capability, thermal insulating elastomeric high build liquid membrane for concrete roofs for exterior wall and exposed surface with solid content not less than 80% and solar reflective index 109 as per (ASTM E1980-19)/tear strength ~20 N/mm (Free film, 14 days, +30 degree C) (ASTM D624) and tensile strength >= 2 N/mm2 (ASTM D4541). (a) After proper surface preparation, Apply one coat of Primer for PU coating as per manufacturers specification. (b) Apply 1st coat of ShaliUrethane® BTD (white) @ 650 gm / m²(minimum) or equivalent by brush / roller while prime surface is tacky, Spread waterproofing reinforced Glass Fiber mash of 45 GSM with overlaps of 50 mm in both directions when the surface is still tacky. Allow 1st coat to dry. (c ) Apply 2nd & 3rd coat of ShaliUrethane® BTD (white) @ 650 gm / m² (minimum) or equivalent by brush/roller. Make : Fosroc/Sika/Choksey/Chemsol/Bostik/STP Note : (i) The Minimum dry film thickness (DFT) of roof treatment shall be 1.5mm if any shortfall in thickness of above treatment the same shall be achieved by additional coat. (ii) The procurement of material and execution of the work of water proofing treatment shall be carried out by authorised applicator approved by GE. (iii) The manufacturer/authorised applicator shall give a warranty for the performance & durability for 10 years.

Supply and laying of CPVC pipes of outer dia 20 mm SDR 11 & Plain CPVC SDR 11 including all fittings i.e Brass elbow, Brass Tee, Male threaded Brass adaptor, Female threaded brass adaptor, unions ball valves, flange and tank adaptor etc) concealed including cutting chases to brick wall/ceiling or laying in floors/trenches and making good complete all as specifed and directed.

Supply and laying of CPVC pipes of outer dia 25 mm SDR 11 & Plain CPVC SDR 11 including all fittings i.e Brass elbow, Brass Tee, Male threaded Brass adaptor, Female threaded brass adaptor, unions ball valves, flange and tank adaptor etc) concealed including cutting chases to brick wall/ceiling or laying in floors/trenches and making good complete all as specifed and directed.

Supply and laying of CPVC pipes of outer dia 32 mm SDR 11 & Plain CPVC SDR 11 including all fittings i.e Brass elbow, Brass Tee, Male threaded Brass adaptor, Female threaded brass adaptor, unions ball valves, flange and tank adaptor etc) concealed including cutting chases to brick wall/ceiling or laying in floors/trenches and making good complete all as specifed and directed.

S&F 40 mm bore PVC low density (LDPE) pipe of pressure 6 kg/Cm2 fixed to wall or laid in floor including stacking GI clamps complete all as specifed and directed by Engr-in-Charge.

S&F 18mm thick high Density High Moisture Resistant (HDHMR) exterior Grade Board with one side designer laminate (OSL) of approved colour and finishing and other side white balancing with density of 850 Kg/cu.m including Z hinges/soft closing hinges (3 per shutter) complete all as specified and directed.

S & F 30mm widht of flange continuous (piano) hinges, stainless steel, bright finish or electrogalvanised.

S&F viterous China squatting pan orrissa pattern size 580 x 440 mm white with intergral foot rests incl P Trap complete including provision of lime concrete bedding complete all as specified & directed.

S&F Vitreous china premium/ 1st quality wash down water closet one piece EWC P/S trap white/ ivory/off white (closed pattern incl all necessary accessorieslike rag bolts/ gel gasket, Seat cover etc.) complete, complete all as specified and directed by Engineer-in-Charge.

S&F premium quality Vitreous China urinals, of size 360mmx345mmx570mm (with assembly kit and urinal spreader set) (back/corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement; fixing flushing system with brackets, including CP bottle trap (9" heavy), CP Brass urinal dome waste coupling full threaded and union for discharge all as specified and directed.

S&F 10 ltr capacity low level PVC valveless, syphonic action type dual type flushing cistern, white, with inlet, ball valve, flush pipe, PVC connection 15 mm dia and 450 mm long float and handle including bracket complete all as specified and directed by Engineer-in-Charge.

S&F Premium quality Stainless steel (SS-304 grade). Matt finish Floor/drain channel (sheet thickness 1.20mm) with grating (Bathroom competible) of size 450x100mm complete all as specifed and directed.

S&F soap dish CP brass 100mm dia (round or oval) fixed to walls or dados. complete all as specified and directed by Engineer - in - Charge.

S&F premium quality CP shower rose 125mm size and shower arm of 15mm dia with 600mm long complete all as specified.

S&F CP Tubular towel rail, 20mm dia, D type, 600mm long between flanges fixed with CP brass screws .

Supply and fix chromium plated Angle/stop valves, cast copper alloy 15 mm bore screwed down high pressure with quarter turn type handle for iron pipe or for union and complete.

S&F chromium plated stop valves, cast copper alloy 15 mm bore screwed down high pressure with quarter turn type for iron/cpvc pipe or for union and complete all as specified and directed by Engineer-in-Charge.

S&F 25 mm CPVC gate valves, with quarter turn handle for CPVC pipe and fixed complete all as specified and directed.

S&F in repairs 15mm bib taps cast copper alloy, chromium plated fancy type with quarter turn handle screwed down screwed for Iron pipe or for brass ferrule and fixed.

Factory made single extruded laminated WPC (Wood Polymer Composite) 100 % solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of but of Frame size 75 x 50 mm(moulded) single rebated, made from wood polymer composite (single extruded process) material comprising of virgin PVC polymer of K value 57-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 780 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note : For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Factory made single extruded WPC (Wood Polymer Composite) 100% solid decorative laminated flush door shutter of 24 mm thick size comprising of virgin polymer of K value 57-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 2000 N (Face) & 1100 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Rates of following items are included : (i) Tower bolts 250mm long of stainless steel 304 finished/of outer plate metal matt finished. (ii) D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 200mm long matt finished. (iii) 4x Butt hinges of size 75mm of stainless steel 202 Grade finished/of outer plate metal.

S&F 20mm bore dia (16 gauge) stainless steel decorative type curtain rod, including SS fancy type decoreted brackets,stops, rollers including end knobs etc complete complete all as specified.

Suuply and fix vitreous china wash hand basin white counter top/bottom type of size 550mm X 400mm, fixed with a set of cast iron brackets including cutting and pinning in ends of brackets to wall, provision of 15mm size basin mixer cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without letter "Hot or cold'' with long scrwed shanks and fly nuts, 32mm dia brass chromium plated waste fittings 450mm long PVC connection of 15mm size with PTMT nuts and CP bottle trap (40mm dia waste pipe) complete.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 200mm long matt finished complete fixed in position all as specified. Make : Harrison (Jasmine) or equivalent as approved by AO

S&F Premium quality stainless steel peg stay of 6 hooks fixed with stainless steel screws complete all as specified and directed.

Suppply and fixing single steel locker of size 2000mmx600mmx600mm, sheet thickness 1mm complete all as shown in TD No CEBT/3877 and painted with hammertone texture powder coated complete all as specified and directed. Make - Godrej or equivalent.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil.

M&L providing cement concrete 1:4:8 type D2 (Using 40mm graded stone agg) , 75 mm thick as in sub base in floor/paving etc.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete. complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete as specified and directed.

M&L for steel water tubing medium grade of size 25 mm bore with all fittings laid in trenches or fixed to wall or floor.complete all as specified and directed by Engineer-in-charge.

Supply and laying GI pipe medium grade ISI marked 20mm dia including all fittings in old/new position as directed by Engr-in-charge of following size.

Supply and Fixing Gun Metal gate valves with iron wheel head,screwed 20 mm both ends for iron pipe,ISI marked, as per IS: 778 complete all as specified.

Supply and Fixing Gun Metal gate valves with iron wheel head,screwed 25 mm both ends for iron pipe,ISI marked, as per IS: 778 complete all as specified.

M & L cutting existing GI water turbing of size 100 mm bore for alternation or addition including screwing/threading and jointing with suitable size GI socket complete all as specified and as directed by Engineer-in-Charge.

Supply and lay jointing, testing and commissioning in replacement of 25 Sqmm x 4 Core XLPE insulated, screened, PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded alominium conductor & PVC sheathed LT cable 1100 Volt grade confirming to IS-7098 lain in trenches/ducts/fixed on poles wall/laid under roads/paths/drain/cilverts or passing through pipes complete all as specified and directed by Engr-in-Charge.

Suppluy, laying DWC pipe size 77 mm OD/ 63 mm ID by excavation method complete all as specified and directed.

M&L for boring hole under road, pavement, hard standing by trenchesless for laying DWC pipe suitable for outer dia of cable passing without damaging Road/Plinth/Floor, complete all as specified and directed by Engr-in-Charge.

DWCPE(SN8) 150mm nominal dia pipes as per IS-16098 (Part-II) laid in trenches on and including 100 mm thick bed comprising of well compacted clean poorly graded garvel/sand mixture with little/ no fines to require slope, Includes all accesories/fittings/jointing ring, jointing and testing complete all as sped and directed by Engr in Charge.

S&F LLDPE septic tank of capacty (Min 4000Ltrs) deigned to carry sewage ang sludge water, including excavation and earthwork in any type of soil installed over and including 100mm th PCC 1:4:8, type D-2 including all necessary fitting for connectiong to inlet and outlet complete all as specified and directed by Engr in Charge

1.8 M dia X 3 M effective depth Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover inter connecting pipes of RCC/DWC and inlcuding vent pipe complete filled with brick bats complete all as specified and directed by Engr in Charge. (Ref TD No BTD-804).

M&L providing factory made precast cement concrete in RCC M-20 in landings, cover slabs (for man holes etc.), chajjas, water troughs, mangers, shelves and similar articles with plain faces setting in mortar (1:4) complete with joints to match all as specified

M & L for concealed conduit point wiring complete for light/ fan on independent /combine board with cable 2.5 sqmm (Nominal area) FRLSH PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC Concealed conduit pipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , after cutting in wall chasing for conduits and sinking's for metal flush boxes suitable length alongwith cover plate 3 mm thick Hylum sheet for mounting, switches, sockets,fan regulator and making the good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth continuity conductor along with point wiring of 2.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and directed by the Engineer in charge.

All as per Srl item No 111 above but for one switch socket combination 5/6 amp on independent board complete all as specified and directed by Engineer - in - Charge. Make of cable - Havells/Anchor/Finolex)

All as per Srl item No 111 above but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No 111 above but for one switch socket combinationt 6 pin 5/ 15 Amps on independent board with copper conductor 2.5 Sqmm complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No 111 above but for Industrial socket on independent board with copper conductor 4 Sqmm complete all as specified and directed by Engr-in-Charge.

S & F Modular switch 5/6 Amps single pole one way, one moudle complete all as specified and directed by Engineer - in - Charge.

S & F Modular switch 1 way 16A, with box complete all as specified and directed by Engineer - in - Charge.

S & F Modular switch 16A -2/3 pin combned 2 Moudle complete all as specified and directed by Engineer - in - Charge.

S & F Modular Socket outlet 5 pin 6 Amps flush type complete all as specified and directed by Engineer - in - Charge.

S & F ceiling rose surface bakelite three terminals complete all as specified and directed by Engineer - in - Charge.

Supply and fix Industrial socket metal clad plug and socket with MCBs single pole 20 Amp complte all as specified and directed by Engineer - in - Charge.

S & F light fitting with LED batten 20W LED batten with 'Eye Soft' technology & glarefree diffuser for perfect application in modern homes or aliminium housing and integrated electronic driver, 20 watt, 50 Hz , 6500K, and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in - Charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

S&F security light fitting LED TYPE 20 watt with all necessary acessories, Clear transparent acrylic cover, prewire suitable to operated on 230 volt 50 HZ AC & Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer - in - Charge

Supply and fixing ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

S&F Heavy duty metal body exahust fan of 300 mm sweep ,240 volt,copper winding, complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to distubed wall in cement mortar (1 :4) white washing matching with existing colour etc.

Supply and fix iron body desert cooler alongiwth stand electric driven (single phase), having nominal air flow capacity of 5000 CuM per hour (or nearest size), honeycomb pad(24' x 24') , water tank 80L capacity, thickness of sheet 20 gauge (minimum) all as specified and directed by Engr-in-Charge.

Supply and fix electric water heater, storage type plastic & steel metal body with glass coating SS tank and heating element upto 2 KW capacity 50 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.

Supply and fix Valve, stop, screwed,20 mm (3/4”) dia pipe complete all as specified and directed by Engineer - in - Charge.

Supply and fix Valve, stop, screwed,25 mm (1”) dia pipe complete all as specified and directed by Engineer - in - Charge.

S & F MCB ‘B’ series type suitable for 240 volts,10 KA, AC supply 6 to 32 Amps , single pole (SP) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F in repairs sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 08 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S & F in repairs sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 04 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S & F in repairs MCB ‘C’ series type suitable for 240 volts, AC supply 5 to 40 Amps , single pole & neutrtal with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F sub-main wiring with two single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLSH stranded copper conductor drawn in PVC conduict dia 20mm “medium quality” conduit including 6.00 Sq mm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and covers including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer - in - Charge. Note : PVC cable and PVC conduit shall be ISI marked.

M & L for Earthing complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level ) with top edge of plate not less than 1.5 Mtr below ground level , connecting to GI earth lead 4 mm dia GI earth wire ,by means of bolts,nuts and washers of GI and protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20 mm grade stone aggregate with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 gs /Sqmm ) and frame of angle iron 25mmX25mmX6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape ,GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmX 8 mm FI with fixing arrangement ,funnel, wire mesh and earth work inhard dense soil ,returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electric plate No.3 of SSR part 1 and connecting to earth test point including taking out unserviceable earthing with all acessories all as specified or indicated including testing on completion all as specified and directed by Engr -In - Charge.

Please Enable Macros to View BoQ information