SPECIAL REPAIR TO DPTI GUEST HOUSE AT PCDA PRAYAGRAJ UNDER GE (WEST) PRAYAGRAJ.

Dismantling the AC (corrugated or semi corrugated) /fibre glass translucent sheet form the roof coverings complete all as specified and directed.

M&L for energy saver LED battan fitting 10 watt, 230 Volts, single tube mounting including with electronic driver LED Printed board, end cover, connector box etc and accessories, prewired, LED including required fixing arrangements and electrical connection two core copper cable from ceiling rose to led light fitting all as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof ridge fixed with self tapping screws complete all as specified and directed.

M&L for Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified & directed.

S&F for Rolled mild steel hollow sections conforming to Gde Fe-290(Gde-165-E) as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails & guides for sliding doors, posts etc fixed with angle cleats or other connecting plates complete all as specified and directed.

S&F high density gypsum partition block wall 80 mm thick bonded with toungue groove joint using suitable adhesives having fire rating of 4 hrs fixed to MS frame using suitable anchors/fasteners, damp proof for exterior use complete all as specified and directed.

Dismantling of wall & celling boards (fiber pulp insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets complete all as specified and directed.

Per Point

S&F solid PVC wall lining consisting of 5mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing with solvent on to wall to make PVC frame as per specifications complete all as specified and directed.

Dismantling of floor,wall tiles incl cement mortar bedding but not backing removing serviciable tiles to stores complete all as specified and directed.

M&L screed bed or bedding layer of mortar (1:4) 15mm thick for laying floor finises of tiles complete all as specified and directed.

M&L for double charged vitrified ceramic tiles 8 to 10mm thick (square/ rectangular) area of each tile exceeding 0.42 sqm but n exc 1.00 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for double charged vitrified ceramic tiles 8 to 10mm thick (square/ rectangular) area of each tile not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Per Point

M&L for rendering 10mm thick in cm 1:4 on verticle surfaces of wall for fixing of wall tiles complete all as specified and directed.

M&L for double charged vitrified ceramic tiles 8 to 10mm thick (square/rectangular) area of each tile exceeding 0.42 sqm but n exc 1.00 sqm in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for double charged vitrified ceramic tiles 8 to 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for glazed digital ceramic coloured tiles in vertical surfaces size 600mmx300mm, 7 to 8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

M&L for glazed digital ceramic highlighter tiles in vertical surfaces size 600mmx300mm, 7 to 8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

Demolition of concrete of any description and in any position complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B-1 (20mm graded crushed stone aggregate) as in levelling course of any position complete all as specified and directed.

M&L for heavy duty endura coloured tiles of size 30cm x 30cm, 8 to 10 mm thick; set jointed and pointed in neat cement slurry in floors, and cut and polished incl 15 mm thick screed bed or bedding layer of mortar CM (1:4) complete all as specified and directed.

M&L for PCC (1:4:8), type D-2 (using 40mm graded crushed stone aggregate) as in sub base 75mm thick complete all as specified and directed.

M&L for E-board tiles ceiling on GI powder coated channel/Tee/Grid of make (Armstrong or equivalent) frame work with the following specification including cutting holes in brick wall built cement mortar & making good in cement concrete 1:2:4 type B-0/Cement mortar 1:3 complete all as specified and directed with following :- (a) M&L fo Plugging to w

M&L for providing precast cement concrete 1:2:4 type B1 in window or door cills, lintels, bressumers, steps,quoin blocks (for use with masonry), stringcourses, copings.kneelers, apex stones, pier caps, columns, posts,boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin) corbels, brackets, etc. (of any section indicated), with plain fair faces,including chamfers, weatherings, throating etc. and setting in mortar 1:4 complete with joints to match complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape, required, including cranking, bending sprially for hoping for cols, hooking ends and binding with MS and including wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Dismantling of stone slab and tiles laid bedded and pointed of any description or thickness in floors, aprons etc complete all as specified and directed.

all around the room and supplying & fixing GI powder coated angle of make Armstrong or equivalent of size 25 X 25 mm X 1.0 mm. (b) S&F 2 mm dia GI wire suspenders with adjustable clamps and dash free fastners with rawl plug and screws plugging in RCC slab placed @ 605 mm centre to centre from perimeter of wall. (c) S&F 25 x 25 x 1.0 mm thick GI tee powder coated as main and cross member at 595 mm centre to centre supported suspenders along with adjustable clamp to maintain level. (d) S&F 4mm thick E-board of approved texure and finished ceiling tiles of size 595 x 595 mm, confirming to relevant IS in squares of GI powder coated tee with clips made to shape, shade and pattern of tiles shall be approved by GE.

M&L for non skid joint free digital ceramic coloured tiles 7mm to 8mm thick (Square/ rectangular) area of each tile exc 0.06 Sqm but n exc 0.11sqm as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified.

Taking down shutters of any description exc. 1.0 sqm but not exc. 2.0 Sqm each leaf complete all as specified and directed.

Taking down Chowkat with shutters w/o taking off shutters from the frame) exc 1.5 sqm but n.exc 4 sqm complete all as specified and directed.

Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

M&L for 80 mm thick machine pressed rubber moulded coloured (red, yellow or combination) interlocking pavor block M-40 grade any shape and size confirming to IS 15658-2006 using white cement with lakour finish over 50 mm thick sand cushion and filling in joints complete all as specified and directed.

Supply and fixing Factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed. Note:1. plain/figured glass thickness not less than 4.00 mm shall also be deemed included in quoted rates and No extra payment will be made separately. 2. for UPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F 1st class hardwood plain solid, straight chowkhats and frames, wrought, framed rebated on the solid rounded or chamfered, put together with glue pinned at joints, fixed in position with MS hold fast/lugs complete all as specified and directed. (Note: M.S. hold fast/ lugs shall be paid for separately).

S&F 35 mm thick 1st class hardwood, teak, glazed and skeleton shtters, open rebated and prepared to rceive gauge, glass etc without sash bars, edges of framing, plain chamfered or rounded, fitted with cut and mitered beads for securing glass etc, sizes of members as specd in SSR part-I section 8 clause 8.24 (a) supplied and fixed to chawkhats with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specd and directed. (Note: stainless steel butt hinges shall be paid separately)

M&L for Z-black granite 18 to 20mm thick of any type work table rubbed and polished in steps ,jambs,pillars,window cills,cooking plateforms and like in cement morter (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl cutting of two nos groove over steps and 20 mm thick screed bed or bedding layer of mortar in CM (1:3) complete all as specified and directed.

M&L for providing and fixing factory made UPVC white colour Sliding Window Three Track made of extruded profiles with wall thickness of 2.3mm (± 0.2mm) Window profile with hollow section with multi chamber, Frame (108mm* 45mm), sliding Sash (39mm *58mm). Sliding mesh sash (39mm* 58mm) Sliding Interlock (One vertical length in each shutters) (45mm* 35mm). Glazing bead (20mm* 18mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 ± 0.2mm thick galvanized steel frame (32mm *13mm), 2 Nos, Sliding Sash (29mm*19mm), Profile to be inserted in required profile, frame will be fixed to the wall with 8mm*100mm long fasteners incl Hardware: Touch Lock of zinc alloyed (White powder coated), steel roller system, glazing and other connected accessories complete all as specified and directed. Note:1. Glazed shutters of float glass thickness not less than 5.00 mm and wiremesh shutter with Stainless steel wire mesh 0.36 mm dia with aparture 1.4 mm shall also be deemed included in quoted rates and No extra payment will be made separately. 2. for UPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 3. Provn for fixing of one window AC/cooler of standard size to be done using suitable uPVC section in one window of each rooms (bottom portion of window top hung glazed shutter and top portion of window sliding type) as directed.

M&L for red granite 18 to 20mm thick of any type work table rubbed and polished in steps ,jambs,pillars,window cills,cooking plateforms and like in cement morter (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl cutting of two nos groove over step and 20 mm thick screed bed or bedding layer of mortar in CM (1:3) complete all as specified and directed.

S&F factory made Solid PVC moulded door shutters 28 to 30 mm thick (stiles) with 2, raised panel design with 2 mm thick moulded Prelam on front face and 2 mm thick prelam PVC sheet on back side completed all aspecifed and directed.

S&F 12mm thick toughened designer glass frosted acid wash for doors, railing, partitions etc with necessary holes for providing locks, handles, floor and top pivot, SS round door stopper etc complete all as specified and directed.

S&F 35 mm thick flush door shutter ,soild core construction with block board core and plywood face panels, commercial type on both sides, both faces covered with decorative face veneer with lipping/frame to match the required shade and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specd and directed. (Note: stainless steel butt hinges shall be paid separately)

S&F for Stainless Steel bottom patch lock set suitable for 12 mm thick toughened Glass door incl necessary screws etc complete all as specified and directed.

S&F for Stainless Steel heavy duty glass to wall lock set suitable for 12 mm thick toughened Glass door incl necessary screws etc complete all as specified and directed.

S&F for Stainless Steel top patch and pivot set suitable for 12 mm thick toughened Glass door incl necessary screws etc complete all as specified and directed.

S&F for Stainless Steel bottom patch and floor spring set suitable for 12 mm thick toughened Glass door incl necessary screws etc complete all as specified and directed.

S&F for Stainless Steel one sided wall to glass hinge for 12 mm thick toughened Glass door incl necessary screws etc complete all as specified and directed.

S&F for Stainless Steel Glass Door Lock Floor Latch Lock Bolt suitable for 12 mm thick toughened Glass door incl necessary screws etc complete all as specified and directed.

S&F for Stainless Steel handle 600 mm long suitable for 12 mm thick toughened Glass door incl necessary screws etc complete all as specified and directed.

S&F in repairs powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F in repair Brass Mortice Lock, 4-6 Lever fixed to Aluminum doors complete all as specified and directed. Make Godrej/Link.

S&F in repairs aluminium (Die cast) body Door closer hydraulically regulated,designation No. 2,universal type, suitable for door shutters of 701to 850 mm in width and of weight between 36 to 60 kg complete all as specified and directed

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box with stainless steel cover fixed to Aluminium doors complete all as specified.

S&F 125 mm long, 12 mm dia SS Dash fasteners for door frames etc incl necessary drilling etc complete all as specified and directed.

S&F 250mm long SS, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections suitable for use with pad lock complete all as specified and directed.

S&F 100 mm size SS butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 150mm size SS handle, fabricated type, fixed with screws complete all as specified and directed.

S&F 200mm size SS tower bolt, fabricated type, fixed with screws complete all as specified and directed.

S&F SS door stopper double 75 mm long having rubber bush 25mm dia fixed to door shutter with steel screw complete all as specified and directed.

S&F 300mm, Helical door springs including roller and roller plate complete all as specified and directed.

S&F in repairs for S S Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Supply and fixing in replacement of 40 /42 W LED 2'x2' Panel surface mounting with high brightness LED package and unique pattern de-glaring PP diffuser and PS LGP de-glaring diffuser sheet for glare free uniform light distribution suitable for furface /recess mounting applications as specifed and directed. Make -Philips full glow surface mount Cat No. SM367LED 42S-6500 G6L54W54 PSU OD or equivalent make as specified in list of make as approved by GE

Demolition of brick work built in cement mortar incl all quoins, arches pillars etc but excluding ashlar facings etc complete all as specified and directed.

M&L for brick work with sub class 'B' bricks,straight or curved on plan exc 6m mean radius built in cm 1:6 complete all as specified and directed.

Taking down cement plaster from brick or stone walls any description including raking out joints, hacking for key, scrubbing down with water to receive plaster removal of rubbish off the premises etc., complete all as specified and directed.

M&L for rendering 15mm thick cement plaster on fair faces of brick work or concrete surfaces in CM (1:6) finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15m thick cement plaster on other than fair faces of brick work or concrete surfaces CM (1:6) finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick cement plaster on ceiling surfaces on brick or concrete surfaces in CM (1:3) with 1mm thick wall care putty complete all as specified and directed.

M&L for 1 mm thick wall care putty on external and internal wall over newly plastererd or old decorated surfaces complete all as specified and directed.

M&L for preparation of new plastererd surfaces of wall and applying two coats of oil bound distemper over chalk whiting primer on plaster surfaces complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of oil bound distemper over chalk whiting primer on plaster surfaces complete all as specified and directed.

S&F in repairs 25 mm dia stainless steel curtain rods with decorative end knobs and brackets complete all as spcified and directed.

S&F Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary,gusset plates, riveting, etc.. n exc kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over

10 kg each to be measured under 'Structural Steel') complete all as specified and directed.

S&F decorative POP cornies of sectional area 30 to 50 sqcm fixed on brick or RCC ceiling complete all as specified and directed.

M&L for complete removal of existing finishes of wall including cornices etc by scraping out, washing, rubbing down and stopping of existing plastered or unplastered surfaces surfaces and applying Two coats of oil emulsion distemper white or tinted of approved shade over a coat of white cement based putty 1-2 mm thick complete all as specified and directed.

M&L for complete removal of existing finishes of ceiling including cornices etc by scraping out, washing, rubbing down and stopping of existing plastered or unplastered surfaces surfaces and applying Two coats of oil emulsion distemper white or tinted of approved shade over a coat of white cement based putty 1-2 mm thick complete all as specified and directed.

M&L for Complete removal of existing treatment of wall and applying white cement based wall care putty(Birla/JK white) on the surfaces with minimum 1 to 2 mm uniform thickness making surface absolutely smooth by grinding with sand paper & applying two coats of Plastic Emulsion Paint white or tinted over one coat of primer complete all as specified and directed .

M&L for Complete removal of existing treatment of ceiling and applying white cement based wall care putty(Birla/JK white) on the surfaces with minimum 1 to 2 mm uniform thickness making surface absolutely smooth by grinding with sand paper & applying two coats of Plastic Emulsion Paint white or tinted over one coat of primer complete all as specified and directed .

M&L for Complete removal of existing treatment of wall and applying white cement based wall care putty(Birla/JK white) on the surfaces with minimum 1 to 2 mm uniform thickness making surface absolutely smooth by grinding with sand paper & applying texture Paint two or more coats applied @ 3.28 ltr /10sqm white or tinted over one coat of primer @ 2.2 kg/10 sqm complete all as specified and directed .

M&L for preparation painting old steel surfaces of any description over 10cm width or girth not other wise described with two coats of synthetic enamel paint complete all as specified and directed .

S&F Aluminium composite panel sheet 3mm thick PVC fixed with necessary aluminium tube of size 25mm x 38mm x 1.5mm thick with required cilicon & screw as in ceiling/columns and in vertical surface complete all as specified and directed. Note : The rate should be incl of scaffolding 14.5m height.

S&F SS steel letters having text height n exc 30 cm of adequate thickness and fixing on height incl all necessary screws, fastner etc complete all as specified and directed.

S&F 18 mm thick PVC sheet minimum 600 Kg density grade 1 quality of both side plain white colour rigid and glossy finish fixed with screws, solvent cement/adhesive as per manufacturer instructions to make kitchen cabinet/ cupboard sides, top and bottom and shelves inside complete all as specified and directed. Note:- Kitchen cabinet/cupboard accessories like handle, hinges etc will be measured and paid separately.

S&F 18 mm thick PVC sheet minimum 600 Kg density grade 1 quality one side decorative lamination and other side plain white colour to make kitchen cabinet/drawer/cupboard shutters fixed with screws, solvent cement/adhesive as per manufacturer instructions to make kitchen cabinet sides, top and bottom and shelves inside complete all as specified and directed. Note:- (a) Kitchen cabinet accessories like handle, hinges etc will be measured and paid separately. (b) Colour and design of prelaminated board shall be approved by Engr-in-Charge.

S&F in repairs stainless steel basket any type [Plain basket of size 50cmx37cmx10cm or 50cmx37cmx16cm, thali basket (11-13 division) of size 50cmx37cmx20cm, plate/partition basket (11-13 division) of size 50cmx37cmx16cm, cutlery basket of size 50cmx37cmx 10cm with bottom of SS perforated sheet, bottom full out of size 50cmx40cmx16cm in two tier] made of 4mm thk SS wire approved quality with suitable telescope basket channel 18"/20" length two way extruded MS galvanised over rollers of approved make for kitchen complete all as specified and directed.

S&F auto closing hydraulic (soft closing) chrome finish stainless steel hinge openable at 110 degree complete all as specified and directed.

S&F continues (piano) hinges, mild steel, bright finish width of flap (when open) 30mm complete all as specified.

S&F 100 mm long stainless steel (grades-304) handle fancy type polished bright chrome finish complete all as specified and directed.

M&L for post construction anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

M&L for post construction anti termiteTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

M&L for post construction anti termiteTreatment at points of wall by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing or concealed conduit writing etc and making good, cutting not exc 10cm girth complete all as specified and directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store 15 mm dia complete all as specified and directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store 20 mm dia complete all as specified and directed.

S&F 15 mm dia GI tubing medium grade with all fittings and fixed complete to walls or laid in floors complete all as specified and directed.

S&F 20 mm dia GI tubing medium grade with all fittings and fixed complete to walls or laid in floors complete all as specified and directed.

M&L in repairs, 75mm dia PVC floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete as specified and directed.

Dismantling/demolition of breaking up drain pipes of upto 110mm dia PVC (SWR),salt glazed ware ,AC pipes set in cement morter or clamps in floor,wall etc complete all as specified and directed.

S&F Solid PVC moulded door frame of size 50mm x 95 mm made out of 5 mm thick single side prelam PVC sheet reinforced with MS tube complete all as specified and directed.

S&F 110mm bore PVC (SWR) rain water,soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls/floor complete all as specified and directed.

S&F bands, straps, supports, stays for rain water pipes incl bolts, holdfasts, clamps and similar articles conforming to Fe-290, Gde-E-165 complete all as specd and directed.

S&F 75mm bore PVC (SWR) soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls/floor complete all as specified and directed.

Dismantling of PVC water storage tank exc 250 and not exc 500 ltrs capacity and removing to store complete all as specified and directed.

S&F rotational moulded,multilayer HDPE water storage tank (white colour three layer) of 500 ltrs capacity(Cylindrical vertical with closed top) ISI marked fixed in position on existing places complete all as specified including 02 Nos 20mm dia full threaded GI tank niple, 20 mm dia PTMT float valve epoxy coated Aluminium rod with high density plastic float ball( of minium weight 210 gms ) and refixing of inlet, outlet & overflow pipe etc, complete all as specified and as directed.

Dismantling of PVC water storage tank exc 500 and not exc 1000 ltrs capacity and removing to store complete all as specified and directed.

M&L for coloured/plain etching over toughed glass before fixing of glass complete all as specified and directed.

S&F rotational moulded,multilayer HDPE water storage tank (white colour three layer) of 1000 ltrs capacity(Cylindrical vertical with closed top) ISI marked fixed in position on existing places complete all as specified including 02 Nos 20mm di

a full threaded GI tank niple, 20 mm dia PTMT float valve epoxy coated Aluminium rod with high density plastic float ball( of minium weight 210 gms ) and refixing of inlet, outlet & overflow pipe etc, complete all as specified and as directed.

S&F in repairs Gun-metal,globe or gate valves with iron wheel head,screwed both ends for iron pipes for 20mm bore of pipe complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F as in repairs 20/25mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe fixed complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F in repair stainless steel kitchen sink bowl type of bowl size 600 mm X 450 mm X 250 mm, 1 mm thick with plug washers and wastes ; including bedding in CM to dwarf wall or including fixing cantilever brackets and connecting union to pipe complete all as specified and directed.

S&F in repair 1 mm thick stainless steel kitchen plate rack 750 x 900 mm of fixed in repair all as specified and as directed. Make- Blue star or equivalent make mentioned in list of make as approved by GE.

S&F in repair brass CP bottle trap of 32mm bore and making it fully leak proof by providing ‘M’ seal on joints complete all as specified and directed.

S&F counter top Basin size ; 610mmx415mmx160mm fixed on granite including cutting for and pinning in ends in CM 1:3 including 32mm dia chromium plated waste coupling complete all as specified and directed. Make:- Jaquar-model-D' ARC Cat No-DRS-WHT-37601 or equivalent make mentioned in list of make as approved by GE.

S&F floor mounted coupled wc bowl with cistern and UF soft close slim seat cover, hinges, fixing Accessories and accessories Set size 380X655X765MM S trap-250mm complete all as specified and directed. Make :- Jaguar cat part No. LYS-WHT-38751S250UFSMZ or equivalent make mentioned in list of make as approved by GE.

S&F in repair toilet paper holder with flap complete all as specified and directed. Make :- Jaguar cat part No. CAN-1153S or equivalent make mentioned in list of make as approved by GE.

S&F in repair brass chromium plated waste coupling for S.S Sink with rubber washer plug etc complete all as specified and directed.

S&F in repair soap dispenser with glass bottle complete all as specified and directed. Make-Jaquar Cat part No. ACN-1135N or equivalent make mentioned in list of make as approved by GE.

S&F in repair soap dish holder complete all as specified and directed. Make-Jaquar Cat part No. ACN-1131N or equivalent make mentioned in list of make as approved by GE.

S&F in repairs CP brass center hole mixer for wash basin for mixing hot and cold water screwed down for iron pipe and fixed for 15 mm bore pipe size complete all as specified and directed. Make:- Jaquar cat Part No: FUS-29023B or equivalent make mentioned in list of make as approved by GE.

S&F in repairs bib taps (wall flange), fancy type, cast copper alloy with capastan head, screwed down, screwed for iron pipe or for brass ferrule of 15 mm bore pipe complete all as specified and directed. Make:- Jaquar cat Part No-FUS 29037 or equivalent make as specified in list of make as approved by GE.

S&F in repairs two way bib cock (wall flange), fancy type, cast copper alloy with capastan head, screwed down, screwed for iron pipe or for brass ferrule of 15 mm bore pipe complete all as specified and directed. Make :- Jaquar cat Part No-FUS 29041 or equivalent make as specified in list of make as approved by GE.

S&F in repairs chromium plated fancy type angle valve for 15 mm bore size complete all as specified and directed. Make:- Jaquar cat part No-FUS 29053 or equivalent make as specified in list of make as approved by GE.

S&F in repair hand shower (health faucet) with 8 mm dia, 1 mtr long flexible long tube & wall hook complete all as specified and diretced. Make:- Jaquar cat part no.- ALD-573 or equivalent make as specified in list of make as approve

d by GE.

S&F in repair towel Rack 600 mm long with lower hangers stainless steel complete all as specified and directed. Make:- Jaquar cat part no.ACN-1181S or equivalent make as specified in list of make as approved by GE.

S&F in repair towel ring square complete all as specified and directed. Make:- Jaquar cat Part No. ACN 1121N or equivalent make as specified in list of make as approved by GE.

S&F in repair vitreous china wash down water closed pan (Pedestal pattern) with 'P' or 'S' trap white, including connection to trap and cistern, flush pipe including white plastic water closet seat cover, closed pattern with flat bottom & cover and aluminium anodised hinging device and making good disturbed surface of floor complete all as specified and directed.

S&F in repair corner glass shelf with bracket complete all as specified and directed. Make:- Jaquar cat part No.ACN-1173 or equivalent make as specified in list of make as approved by GE.

S&F in repair glass shelf 600 long complete all as specified and directed. Make:- Jaquar cat part no. CAN 1171N or equivalent make as specified in list of make as approved by GE.

S&F in repair double arm wall mounted reverseable plain /magnifine mirror complete all as specified and directed. Make- Jaquar cat part no. ACN-1193N or equivalent make as specified in list of make as approved by GE.

S&F in repair tumbler holder complete all as specified and directed. Make:- Jaquar cat part no. ACN-1141N or equivalent make as specified in list of make as approved by GE.

S&F in repair pillar taps 15mm bore, swan neck type cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe or for brass ferrule (weight should not be less than 0.665kg) complete all as specified and directed.

Taking down shutters of any description exc. 1.0 sqm but not exc. 2.0 Sqm each leaf and refixing in the same opening after easing and adjusting complete all as specified and directed.

M&L for porselano glazed vitrified tiles 8 to 10 mm thick (square/ rectangular) area of each tile exceeding 2.00 sqm but n exc 3.00 sqm in floors/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Taking down carefully point wiring of any type complete for light, fan socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets, regulators, wooden batten, surface conduit/casing caping/conceal etc. removing materials including accessories for taking credit and making good disturbed surface to match the existing complete all as specified & directed.

M&L for Point wiring complete in modular switch, socket with 1.5 Sq mm (nominal area) PVC insulated flame retardent low smoke un-sheathed and multicore copper conductor cable with colour code ISI marked in and including PVC concealed conduit ISI marked and conduit fittings for one light point/fan point/engagement light controlled by one switch including PVC insulated 1.5 Sqmm single core copper earth wire to common earth and connecting to earth dolly and including suitable Anodized sunken box as per manufacture design and plate for modular of switch , socket etc with grid plate, crown with captive screws all as directed and specified. Note :- Rate is inclusive of Cutting/chases of wall/floor/ceiling.

S&F in replacement of round shape 12 watt 220 volts AC Surfaccetype with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F in repair braided hose connections 15mm size with nuts and length 600 mm complete all as specified and directed. Make:- Jaquar cat part no. ALD-801B or equivalen make as specified in list of maket as approved by GE.

S&F in repair framed shower encloseres corner entry half rounded encloser size -H-1950mm,W-1200mmx1200mm with curved sliding doors 6mm thick glasss and finished crome complete all as specified and directed. Make: - Jaquar model-Delta Cat No-JSE-CHR-DEL 1212X or equivalent make as specified in list of make as approved by GE.

S&F in repair shower panel Jaq Brushed stainless steel size 1400x200mm complete all as specified and directed. Make:- Jaquar model-Jaq Brushed S S with Cat No-JPL-SSF-ST8858B3 or equivalent make as specified in list of make as approved by GE.

S&F modular socket out let 2-in-1, 3 pin, 5/6 amp flush type 2 module complete all as specified & directed.

S&F in repair artificial marble ledge of size 1200x1200 mm, light/dark shade as approved complete all as specified and directed. Make: - Jaquar Cat Part No. ESA-WHT-LDG1212 or equivalent make as specified in list of make as approved by GE.

All as per srl No. 143 above but one three pin switch socket outlet 5 Amps on the independant board.

All as per item Sl. No. 143 here in before but wiring with 2.5 sq.mm multistranded cable and earth wire with copper conductor of size 2.5 sq.mm for 15 amps power point.

Supply and fixing in replacement of Environmental friendly aesthetically designed ,decorative Surface mounted 5W LED Surface Spotlight with aluminum structure, available with adjustable light engine to achieve the desired illumination angle all as specifed and directed Make Havells Full glow Cat No. LED Unispot Round BLK 5 W 4000 or equivalent make as specified in list of make as approved by GE.

Supply and fixing in replacement of dual wall bracket Decorative, wall mounting, metal and chrome & glass opal paint finish including 2X10 wall LED bulb fixture With bulb base E32 complete all as directed. Make Havells Full glow Cat No. LHFOAJE1TZ1I060 or equivalent make as specified in list of make as approved by GE.

Supply and fixing Ceiling rose, surface bakelite 2 to 3 terminal, 240 volts, 5 Amps ISI Marked complete all as specified and directed.

S&F Electronic Multy music type Bell, AC 240 volts single pole, complete all as specified.

Taking down ceiling fan/exhaust fan from position and kept in safe cutody complete all as specified and directed.

Supply and hanging /fixing ceiling fan 1200 mm sweep AC Supply (Input Voltage Range ; 120 to 280V), BLDC type, 5 star rated, BEE approved , super enamelled, copper winding of 'B' class insulation, single phase, minium 26W (± 10%), Temperature rise 40 degree maximum without remote with and including operative based capacitive regulator, 03 No blades, down rod including accessories, white colour, total harmonic less than 10%, 5 speed, hanging in position including making connection with flexible cord three core twisted copper conductor of suitable size from ceiling rose to fan complete all as specified and directed.

S&F modular Switch out let 2-in-1, 3 pin, 15/16 amp flush type 2 module complete all as specified & directed.

S&F modular socket out let 2-in-1, 3 pin, 5 /16 amp flush type 2 module complete all as specified & directed.

S&F modular fan regulator, 5 stepped, electronic type, single phase, 120 watt, 1/2 module incl connection complete complete all as specified & directed.

S&F Modular bell push flush type 6 amp, 1 module SP , 230V AC complete all as specified & directed.

S&F Exhaust fan, 300 mm sweep heavy metal body, 240 volts complete with lovers shutters and mounted in suitable opening arrangement in wall and connecting up including three core PVC insulated PVC sheathed copper conductor flexible cable 1.5mm drawn in flexible PVC conduit and fixed by using 4 Nos, 200 mm long 12 mm dia bolts nuts and washers and grouted in wall in CM(1:3), complete all as specified and directed.

M&L for energy saver LED battan fitting 20 watt, 230 Volts, single tube mounting including with electronic driver LED Printed board, end cover, connector box etc and accessories, prewired, LED including required fixing arrangements and electrical connection two core copper cable from ceiling rose to led light fitting all as directed.

M&L for energy saver LED battan fitting36/ 40 watt, 230 Volts, single tube mounting including with electronic driver LED Printed board, end cover, connector box etc and accessories, prewired, LED including required fixing arrangements and electrical connection two core copper cable from ceiling rose to led light fitting all as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of ancolour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F double door metallic sheet metal enclosure for DB when MCBs to be used TPNL, 4 ways, 415Volts (horizontal type) with 200 Amps rated bus bar IP 43 - IK 09 suitable for TPN MCB/ 4 pole Isolator fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs for cables/wires complete all as directed.

M&L for water proofing treatment to sunken floor consisting of the following operation:- (a) Cleaning of surfaces by wire brushing brooming removing dust particles (b) M&L PCC 1:2:4 type (B0) using 12.5mm graded crushed stone aggregate 25mm thick, finishing the surface even and smooth as levelling course without using extra cement. (c) Applying two coat of Fosroc Brushbond 2 component POLYMER MODIFIED CEMENTITIOUS water proof coating with proper overlapping when the coating is green all as sepcified. (d) Laying of water proof protective layer of cement mortar screed in the ratio of 1:4 15mm thick mixed with and including integral water proofing compound Fosroc Conplast WL as per manufacturer instruction, finishing the surface even and smooth without using extra cement. (e) Demolition of lean concrete with existing treatment and M& L for PCC 1:5:10 for filing of sunken portion is deemed to be included in the rates.

S&F Exhaust fan, 450 mm sweep heavy metal body, 240 volts complete with lovers shutters and mounted in suitable opening arrangement in wall and connecting up including three core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm drawn in flexible PVC conduit and fixed by using 4 Nos, 200 mm long 12 mm dia bolts nuts and washers and grouted in wall in CM(1:3), complete all as specified.

S&F modular switch, 5/6 amps, 230V AC, 1 module complete all as specified & directed.

Supply and fix Three pin metalic plug & socket 20A outlet , Modular type, 230 volts for SP/DP MCB and 2 pole and Earth Metal enclsoure. Make : Havells Cat part no DHDPUSN020/DHDPUDP020 or equivelent make as specified in list of make approved by GE.

Supply and fixing in replacement of 25 W LED 2'x2' Panel Ultra slim recess mounted LED module with high brightness LED package and unique pattern de-glaring PP diffuser and PS LGP de-glaring diffuser sheet for glare free uniform light distribution suitable for armstrong / grid ceiling applications all as directed by Engr-in-Charge. Make Philips Full glow Cat No. SM367 LED25S-6500 G6 L54W54 PSU OD or equivalent as approved by GE