Replacement of panel interlocking with Electronic interlocking System with outdoor Signalling AND Telecom arrangements at Dodbelle,herehalli and golehalli stations between YPR-TK section of BANGALORE division.

Item Breakup - 1-SOR A

70.00 drawing No.SG/CN/02/13 and earthing of metallic sheath and armour of all cables in all apparatus cases, relay room, equipment room, SM's room for block and control, and earthing of all equipments in apparatus cases, power room, relay rack, cable termination rack, control panel, signals, lever frames with MS flat 35mm X 6mm/19c cable (MS flat for closer by areas and MS flat/19c cable combination for farther areas) as per the instructions of Railway representative at site. The work includes painting of earth resistance value on the earth pit. (Supply of 19C cable is not covered in the scope of this schedule). [MS flat for earthing 35mm X 6mm, cement, GI earth electrodes, common salt, charcoal, country bricks, M sand, soldering materials and all other miscellaneous materials required for the work shall be supplied by the Contractor].

52.00 fixing t h e s a m e o n t h e hardwood plank available and extending the 110VAC using w i r e P V C 3/0.75mm copper, i n a l l the apparatus cases, as per the instructions of Railway representative at site. [2 pin s o c k e t - 5 A w i t h s w i t c h , w i r e PVC 3 / 0 . 7 5 m m c o p p e r a n d a l l other miscellaneous materials required f o r the work shall be supplied by the Contractor].

980.00 RCC cable markers a s p e r drawing No.CSTE/CN/OFC/1. T h e lettering o n the cable marker shall be "SIG" / "TELE" / "OFC" as p e r t h e instructions o f Railway representative a t site.) as per drawing enclosed

13000.00 soil except hard rocky areas including clearing of roots of trees, rocks, bushes etc. to a depth of 1.0 Mtrs and to a width of 0.3 Mtrs. (Laying o f c a b l e s i s not included in this schedule) SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

6000.00 soil except hard rocky areas including clearing of roots of trees, rocks, bushes etc. to a depth of 1.0 Mtrs and to a width of 0.5 Mtrs. (Laying o f c a b l e s i s not included in this schedule.)

400.00 for track crossing of cables, refilling of trench by ramming and consolidating it as p e r the instructions of Railway representative at site after l a y i n g of D W C / RC C p i p e s . During excavation of trench, i t h a s t o b e ensured that the excavated soil does not mix with the ballast available. The depth o f 1 m trench shall b e from t h e bottom o f sleepers for track crossings. Laying of cables and DWC pipes is not included in this schedule. (Supply of DWC/RCC pipes with couplers/collars is not included in this schedule).

250.00 for road crossing of cables, laying of DWC/ RCC pipes with collar/ coupling, refilling of trench by ramming a n d consolidating it and resurfacing it to the original position. Laying of cables is not included in this schedule. (Supply o f DWC/RCC pipes with couplers/collars is not included in this schedule).

900.00 cable laying with offset at both ends and with couplings over RCC bridges, drainage, culverts, and girder bridges. For RCC bridges, drainage, and culverts, the pipes shall be mounted on concrete masonry supports of size 300mm x 300mm x 300mm at an interval of 2 meters. For girder bridges, the pipes shall be fixed on suitable MS clamps at an interval of 2 meters. The ends of the pipes shall be closed with brick masonry abutments to ensure that no cable is exposed. The work shall be carried out as per the instructions of the Railway representative at the site.(Supply of GI pipes with couplings and laying of cables is not included in this schedule).Stone jelly (20/25mm size), bricks, sand, cement, MS angles, flats, bolts, nuts for manufacturing and fixing clamps, bricks, M sand, cement, and other miscellaneous materials for the work shall be supplied by the contractor.

600.00 cable laying in hard rocky area with off sets at b o t h e n d s d u l y supported by concrete blocks of size 300mm x 300 mm x 300 mm at an interval of 2m. The ends of the pipes shall b e closed w i t h brick masonry abutments work so that no cable is exposed, The work shall be carried out a s p e r the instructions of Railway representative at site.(Supply of GI pipes with couplings and laying of cables is not included in this schedule).[Stone jelly of size 20/25mm, bricks, sand, cement, and all other miscellaneous materials required f o r t h e w o r k s h a l l be supplied by the Contractor]. SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

f signaling/power/ Metre telecommunication c a b l e s a s p e r cable plan in cable trenches, masonry ducts, RCC Pipes, DWC pipes, GI Pipes etc. (Supply o f cables i s n o t included i n this schedule).

14000.00 0.3m width throughout, with earth after laying of cables, a n d consolidating the trench by ramming and levelling."

6500.00 0.5m width throughout, with earth after laying of cables, a n d consolidating the trench by ramming and levelling."

980.00 size 300mmX300mm, casting o f concrete f o u n d a t i o no f size 300mmX300mmX300mm and Placing of RCC cable markers on top of the foundation a n d r e fi l l i n g t h e p i t and consolidating i t b y ramming. T h e cable markers shall be provided at an interval of 20 Mtrs. within station limits and 5 0 Mtrs. outside station limits throughout the cable r o u t e , diversions a n d a l s o a t every track/road crossing."

200.00 1.5mx1.5m a n d d e p t h a s instructed by Railway representative at site, for coiling the cables i n rea r o f relay rooms/ AFTC huts, apparatus c a s e s e t c . T h e work includes coiling t h e underground cables a n d placing closely o n e layer o f country bricks of size approx. 220mm x 100mm x 60mm breadth wise above the cables to cover all the cables in the cable pit, closing and consolidating the pit by ramming and levelling.[Country bricks of size 220mmx100mmx60mm (approximately) shall be supplied by the Contractor].

4.00 arrangement for Signals in RE area a s per standard practice. T h e work comprises of providing MS angle frame and wire mesh in order to avoid close proximity of OHE wires. The work also includes provision of earthing wire using 4 S W G G I wires from the screening arrangement up to surface base as per t h e instructions o f Railway representative at site.[All materials required for this work shall be supplied by the Contractor].

24.00 d i a , 4 . 6 m / 3 . 6 m t a l l w i t h necessary inspection a s p e r specification/ drawing/ description enclosed in this document. a)Supply o f colour light Signal pole 4.6m tall and 140 mm dia(Galvanised)

18.00 d i a , 4 . 6 m / 3 . 6 m t a l l w i t h necessary inspection a s p e r specification/ drawing/ description enclosed in this document. b)Supply o f colour light Signal pole 3.6m tall and 140 mm dia (Galvanised)

46.00 pole 140mm dia with necessary inspection a s p e r specification/ drawing/ description enclosed in this document. SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

24.00 to suit C L S p o l e 4 . 6 m / 3 . 6 m t a l l , with necessary inspection a s p e r specification/ d r a w i n g / description e n c l o s e d i n this document. a)Supply o f l a d d e r with platform (4.6m) for CLS(Galvanised)

24.00 to suit C L S p o l e 4 . 6 m / 3 . 6 m t a l l , with necessary inspection a s p e r specification/ d r a w i n g / description e n c l o s e d i n this document. b)Supply o f l a d d e r with platform (3.6m) for CLS(Galvanised)

24.00 complete with hood etc., with necessary inspection as per specification/ drawing/ description enclosed in this document.

8.00 complete w ith surface base, signal pole, hood etc., with necessary inspection as per specification/ d r a w i n g / description enclosed in this document.

22.00 type- complete for 4/ 3/ 2 aspect with mounting socket, w i t h necessary inspection a s per specification/ drawing/ description enclosed in this document. b)Supply of colour light Signal unit (3 aspect)

26.00 type- complete for 4/ 3/ 2 aspect with mounting socket, w i t h necessary inspection a s per specification/ drawing/ description enclosed in this document. c)Supply of colour light Signal unit (2 aspect)

4.00 15121.70 unit arm - 1/ 2/ 3/ 4/ 5/ 6 way with mounting sockets, with necessary inspection as per specification/ drawing/ description enclosed in this document. a) Supply of Junction type route indicator - 1 way

7.00 22260.70 unit arm - 1/ 2/ 3/ 4/ 5/ 6 way with mounting sockets, with necessary inspection as per specification/ drawing/ description enclosed in this document. c)Supply of Junction type route indicator - 3 way

32.00 light - complete with necessary inspection as per specification/ drawing/ description enclosed in this document. a)Supply of Calling On Signal

12.00 made of cast iron with necessary inspection as p e r specification/ drawing/ description enclosed in this document. a)Supply of Off set bracket - large

24.00 made of cast iron with necessary inspection as p e r specification/ drawing/ description enclosed in this document. b)Supply of Off set bracket - small

150.00 for a)LED a s p e c t s w i t h p l u g boards, connectors and retaining clips with necessary inspection as per specification/ SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

60.00 relays with necessary inspection a s per specification/

52.00 frames of suitable size to hold up to 4/ 8/ 12/ 20 relays /plug i n type a s required by Railways and fixing them in apparatus cases for all types of signal control circuits, LC gate control circuit a n d Point contro l circuits, fixing o f p l u g boards, r e l a y s , r e s i s t o r s and electrolytic condensers on Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Ty p e F 5 , w i r i n g and termination as per a p p r o v e d circuit diagram and painting the particulars.[Wire P V C coppe r, 3/0.75mm and 16/0.2mm copper, Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, for fixing resistors and condensers, MS flats 25mm x 6mm brass bolts a n d nuts, p a i n t s , s o l d e r i n g materials, resistors, condensers a n d a l l other miscellaneous materials required f o r the work shall be supplied by the contractor]. a)Wiring of Signal/ point/ LC control circuit (up to 4 relays/Plug in type)

22.00 frames of suitable size to hold up to 4/ 8/ 12/ 20 relays /plug i n type a s required by Railways and fixing them in apparatus cases for all types of signal control circuits, LC gate control circuit a n d Point contro l circuits, fixing o f p l u g boards, r e l a y s , r e s i s t o r s and electrolytic condensers on Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Ty p e F 5 , w i r i n g and termination as per a p p r o v e d circuit diagram and painting the particulars.[Wire P V C coppe r, 3/0.75mm and 16/0.2mm copper, Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, for fixing resistors and condensers, MS flats 25mm x 6mm brass bolts a n d nuts, p a i n t s , s o l d e r i n g materials, resistors, condensers a n d a l l other miscellaneous materials required f o r the work shall be supplied by the contractor]. b)Wiring of Signal/ Point/ L C control circuit (up to 8 relays/plug in type) SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

4.00 11355.02 frames of suitable size to hold up to 4/ 8/ 12/ 20 relays /plug i n type a s required by Railways and fixing them in apparatus cases for all types of signal control circuits, LC gate control circuit a n d Point contro l circuits, fixing o f p l u g boards, r e l a y s , r e s i s t o r s and electrolytic condensers on Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Ty p e F 5 , w i r i n g and termination as per a p p r o v e d circuit diagram and painting the particulars.[Wire P V C coppe r, 3/0.75mm and 16/0.2mm copper, Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, for fixing resistors and condensers, MS flats 25mm x 6mm brass bolts a n d nuts, p a i n t s , s o l d e r i n g materials, resistors, condensers a n d a l l other miscellaneous materials required f o r the work shall be supplied by the contractor]. c)Wiring of Signal/ Point/ L C control circuit (up to 12 relays/plug in type)

120.00 boards, connectors and retaining clips with necessary inspection as per specification

120.00 boards, connectors and retaining clips with necessaryinspectiona s per specification/drawing/

1800.00 thick as per Technical specification

480.00 type with 4 terminals and stumps with necessary inspection a s p e r specification/ drawing/ description enclosed in this document.

13500.00 centre and PBT Fuse blocks with necessary inspection a s p e r specification/ drawing/ description enclosed in this document. a)Supply of PBT terminals 25mm centre.

850.00 centre and PBT Fuse blocks with necessary inspection a s p e r specification/ drawing/ description enclosed in this document. b)Supply of PBT terminals 60mm centre.

850.00 centre and PBT Fuse blocks with necessary inspection a s p e r specification/ drawing/ description enclosed in this document. c)Supply of PBT fuse block without ND fuse

180.00 quarter size) to suit Southern Railway standard with necessary inspection a s per specification/ drawing/ description enclosed i n this document a)Supply of apparatus case - Full size

30.00 quarter size) to suit Southern Railway standard with necessary inspection a s per specification/ drawing/ description enclosed i n this document b)Supply of apparatus case - Half size SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

6.00 fronted b o x o f size 300mm x 600mm x 75mm with hooks to keep various keys with description engraved on the tags. [TW Glass fronted box of size 300mmx600mmx 75mm with built in lock, hooks, engraved tags and all other miscellaneous materials required for the work shall be supplied by the Contractor].

144.00 less than 6mm thick and with an insulation Foot to withstand 650VAC, on the floor o f relay room etc at places as indicated by railway representative at site."

18.00 machine-IRS t y p e a n d connecting all ground connections including wiring and termination in p o i n t m a c h i n e and interconnections between point machine and CT box through PVC hose pipe with 3/0.75mm and 7/1.40mm copper wire and painting. This work includes provision of insulation to stretcher bars, throw bar lug a n d "D" bracket w h e r e v e r required, cutting of notches on the point machines covers to suit crank handle configuration. (Combined type point machine with ground connection, uninsulated stretcher bar, throw bar lug and 'D' brackets will be supplied by Railways.[All types of insulations connected to point work, coal bengal, all type of bolts and nuts, washers spring/flat wire PVC 7/1.4mm copper, PVC hope pipe, paints, PVC/nylon sleeves and all other miscellaneous materials required f o r t h e w o r k s h a l l b e supplied by the Contractor].

8.00 The work i n v o l v e s fi x i n g o f platform repeater using suitable fixing arrangements at places indicated, wiring t h e s a m e a n d p a i n t i n g as per the instructions o f Railway representative at site. The signal shall be connected t o the a p p a r a t u s c a s e using cables neatly clamped. The work also includes provision of one EWS lock. (Laying of cable is not included in the scope of this work.) (Supply of repeater signals and cables is not included in this schedule).[Wire PVC 3/0.75mm copper, paint, EWS lock and all other miscellaneous materials required for t h e w o r k s h a l l b e s u p p l i e d by the Contractor].

46.00 foundation as per Drg.No.SG/CN/02/9 using metallic templates, f o r erection of colour light signals up to 4 aspects. [Foundation bolts, cement, M sand, stone jelly o f size 20/25mm d i a a n d a l l other miscellaneous materials required f o r the work shall be supplied by the Contractor]. SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

46.00 mounting o f colour light signal u p t o 4 aspects complete o n Signal pole/ Off-set bracket, ( f o r L E D / filament b u l b s ) with lenses, triple p o l e l a m p holder, filament switching units, C L S transformer, current regulators (whichever is applicable), fixing of ladder w i t h platform complete and concreting of ladder shoe, fixing of number plates, marker board, lens guard, fixing of s p e e d l i m i t b o a r d wherever necessary, termination o f tail cables, wiring o f signal u n i t w i t h P V C w i r e 3/0.75mm copper, provision of EWS locks, and painting of one c o a t o f r e d o x i d e a n d t w o c o a t s of aluminium/ enamel paints. When the aspect is fixed on Offset bracket using 'U' bolts and nuts, a through b o l t shall be provided by drilling a hole i n t h e signal pole t o prevent the offset bracket from sliding down.(Supply of surface base, Offset bracket, CLS pole, C L S aspects complete, ladder with shoes and platform, Speed limit board, LED aspects, current regulators, lamp holders, lamps, filament switching unit and CLS transformer is not covered in this schedule).['U' bolts and nuts, through bolts and nuts, cement, stone jelly 20/25mm dia , M sand, Signal Collar Rings, wire P V C 3/0.75mm copper, lens-guard, all fixing bolts and nuts, lead wool, paints PVC/Nylon sleeves, enameled number plates. enameled marker boards, E W S locks, a n d a l l other miscellaneous materials for the work shall be supplied by the Contractor]."

12.00 foundation a s p e r D r g , No.SG/CN/02/10 using metallic templates, f o r erection of g r o u n d t y p e c o l o u r l i g h t s h u n t signal. [Foundation bolts and nuts, cement, M sand, stone jelly o f size 20/25mm and all other miscellaneous materials for the work shall be supplied by the Contractor]."

12.00 complete including surface base, signal pole, LED aspects/ l e n s e s , b u l b s with holders (whichever is applicable), fixing of lens guards, number plate, termination of tail cables, wiring o f signal unit with PVC wire 3/0.75mm copper, provision o f EWS locks and painting of one coat of red oxide and two coats of Aluminium/ enamel paint. ( S u p p l y o f G r o u n d t y p e s h u n t signal complete including surface base, signal pole, LED aspects, holder, bulbs, and lenses is not covered i n t h i s schedule). [Wire PVC 3/0.75mm copper, lens guards, EWS locks, Enameled number plates, bolts and nuts, lead wool, paints and all other miscellaneous materials shall b e supplied by the Contractor]." SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

15.00 and nuts, erection o f P o s t t y p e shunt Signals, termination o f t a i l c a b l e s and wiring using wire P V C 3/0.75mm copper, provision of EWS lock and painting o f one c o a t o f red-"oxide and two coats of aluminium/ enameled paint. The work also includes drilling suitable holes o n the CLS post and provision o f a through bolt with nut to prevent the Off-setbracket from slipping down."

3.00 w a y t o 6 w a y s - complete/ fi x i n g of additional l i m b t o t h e e x i s t i n g route indicators, termination of tail cables, wiring as per approved circuits diagram using wire PVC 3/0.75mm copper, provision of required No of EWS locks, wire mesh, and painting.(Supply o f junction t y p e Route Indicators - complete and additional limb is not covered in this schedule).[3/0.75mm wire PVC, fixing bolts and nuts, EWS locks, wire mesh, PVC/Nylon sleeves, paints and all other miscellaneous materials shall be supplied by the Contractor]. a)Fixing and wiring of direction type route indicator - 1 way

3.00 w a y t o 6 w a y s - complete/ fi x i n g of additional l i m b t o t h e e x i s t i n g route indicators, termination of tail cables, wiring as per approved circuits diagram using wire PVC 3/0.75mm copper, provision of required No of EWS locks, wire mesh, and painting.(Supply o f junction t y p e Route Indicators - complete and additional limb is not covered in this schedule).[3/0.75mm wire PVC, fixing bolts and nuts, EWS locks, wire mesh, PVC/Nylon sleeves, paints and all other miscellaneous materials shall be supplied by the Contractor].c)Fixing and wiring of direction type route indicator - 3 way

31.00 and nuts, erection of Calling On Signals/ 'A' marker lights, termination of tail cables and wiring u s i n g w i r e P V C 3/0.75mm copper, provision o f E W S l o c k , number plates/ marker boards a n d painting. The work also includes drilling suitable holes on t h e CLS post and provision of a through bolt with nut to prevent the Off-set bracket from slipping down.(Supply o f Calling on S i g n a l / ' A ' marker light, LED aspects/holders & b u l b s a n d Off set brackets is not covered in this schedule). ['U' bolts and nuts, through bolts with nut, w i r e P V C 3/0.75mm copper, E W S lock, E n a m e l e d n u m b e r p l a t e s , w i r e mesh, PVC/Nylon sleeves, paints a n d a l l other miscellaneous materials shall be supplied by the contractor]. SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

36.00 circuit to suit RE/ Non-RE areas as per approved signaling plan using Plug-in type track relays. This work includes provision of double bonding, and parallel jumpers, provision of bond wire clips, provision of track lead connections using 2c X 2.5 sq.mm cable, provision of TLD boxes 2 Nos. at Relay end, 2 Nos. at Feed end and 2 No's for parallel jumpers as necessary to suit layouts, for each Track Circuit, and termination of jumpers and tail cables in track lead junction boxes, installation of relays, track feed battery chargers to charge up to 4 cells, track feed resistance, 'B' type choke' and secondary cells - 80 AH capacity in apparatus cases and wiring with wire PVC 3/0.75mm copper. The work also includes painting of track Circuit No. with Feed end/ Relay end details on the TLD boxes. The work also includes provision of insulations for gauge tie plates and nose crossing plates wherever required. (Provision of rail joint insulation is not covered in this schedule.) (Uninsulated gauge type plate and nose crossing plate will be supplied by Railways. Supply of track feed battery charger, 'B' type choke, track relays, un- charged secondary cells (2V - 80AH), TLD boxes with stumps,2cX2.5 sq.mm cable, is not covered in this schedule). a)Provision of track circuit in RE/Non RE area (point zone)

54.00 circuit to suit RE/ Non-RE areas as per approved signaling plan using Plug-in type track relays. This work includes provision of double bonding, and parallel jumpers, provision of bond wire clips, provision of track lead connections using 2c X 2.5 sq.mm cable, provision of TLD boxes 2 Nos. at Relay end, 2 Nos. at Feed end and 2 No's for parallel jumpers as necessary to suit layouts, for each Track Circuit, and termination of jumpers and tail cables in track lead junction boxes, installation of relays, track feed battery chargers to charge up to 4 cells, track feed resistance, 'B' type choke' and secondary cells - 80 AH capacity in apparatus cases and wiring with wire PVC 3/0.75mm copper. The work also includes painting of track Circuit No. with Feed end/ Relay end details on the TLD boxes. The work also includes provision of insulations for gauge tie plates and nose crossing plates wherever required. (Provision of rail joint insulation is not covered in this schedule.) (Uninsulated gauge type plate and nose crossing plate will be supplied by Railways. Supply of track feed battery charger, 'B' type choke, track relays, un- charged secondary cells (2V - 80AH), TLD boxes with stumps,2cX2.5 sq.mm cable, is not covered in this schedule). b)Provision of track circuit in RE/Non RE area (other than point zone) SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

200.00 foundation and erection of apparatus case full size a s p e r D r g . No.SG/CN/02/6 and fixing of 2 Nos. of 'E' type locks, one for the front doo r a n d another f o r t h e back door, fixing o f one hard wood shelf plank 37mm thick and painting the apparatus case inside and outside with one coat of red-oxide and two coats of aluminium paints.(Supply of apparatus case is not included in this schedule).[Foundation bolts & nuts, ' E ' t y p e locks, cement, M s a n d , s t o n e j e l l y o f s i z e 20/25 mm, hardwood plank of 37mm thick, paints, varnish, fixing bolts & nuts a n d a l l other miscellaneous m a t e r i a l s r e q u i r e d for thework shall be supplied by the Contractor.]

34.00 foundation and erection of apparatus case half size as per Drg, No.SG/CN/02/7, fixing o n e ' E ' type loc k f o r t h e front doo r and latching arrangement for the back door, and fixing o f o n e hardwood shelf plank 37mm thick and painting the apparatus case inside and outside with one coat of red-oxide and two coats of aluminium paints.(Supply of apparatus case is not included in this schedule).[Foundation bolts and nuts, cement, 'E' type locks, M sand, stone jelly of size 20/25mm,37mm hard wood planks, latching ""arrangements, paints, varnish, fixing bolts & nuts a n d a l l other miscellaneous materials required f o r t h e w ork shall be supplied by the Contractor]"""

18000.00 p o w e r c a b l e s a n d i n t e r n a l w i r i n g on terminal/ f u s e blocks i n n e w apparatus cases, cable termination boxes and in gate Lodges excluding cable termination rack at relay room. The work includes fixing of all new cables by teakwood clamp on teakwood base plank, fixing o f Phynolic synthetic industrial fibre base fine weave cotton fibre board 6mm thick for terminal board to suit each a p p a r a t u s case, varnishing all teakwood items, fi x i n g of terminals/ fuse blocks o n t h e terminal b o a r d , d r i l l i n g of necessary holes, termination of cables, wiring, identification of cables using aluminium tags with letters punched neatly, as p e r approved circuit d i a g r a m a n d cable plan, p a i n t i n g of particulars on sleeves andalso on the inner side of the doors of apparatus cases. After terminations are "over, the side openings o f apparatus case foundation s h a l l be closed with brick work, cement plastered, the inter-space filled with M sand u p to base level and the bottom surface shall be sealed with sealing compound.(Supply of PBT terminals and Fuse blocks is not covered i n this schedule)." a)Termination on 25/60mm PBT terminals (new location) (Phynolic sheet)(Per Unit = Per Terminal block) SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

700.00 p o w e r c a b l e s a n d i n t e r n a l w i r i n g on terminal/ f u s e blocks i n n e w apparatus cases, cable termination boxes and in gate Lodges excluding cable termination rack at relay room. The work includes fixing of all new cables by teakwood clamp on teakwood base plank, fixing o f Phynolic synthetic industrial fibre base fine weave cotton fibre board 6mm thick for terminal board to suit each a p p a r a t u s case, varnishing all teakwood items, fi x i n g of terminals/ fuse blocks o n t h e terminal b o a r d , d r i l l i n g of necessary holes, termination of cables, wiring, identification of cables using aluminium tags with letters punched neatly, as p e r approved circuit d i a g r a m a n d cable plan, p a i n t i n g of particulars on sleeves andalso on the inner side of the doors of apparatus cases. After terminations are "over, the side openings o f apparatus case foundation s h a l l be closed with brick work, cement plastered, the inter-space filled with M sand u p to base level and the bottom surface shall be sealed with sealing compound.(Supply of PBT terminals and Fuse blocks is not covered i n this schedule)." b)Termination on PBT fuse block (new location) (Phynolic sheet)(Per Unit = Per Fuse block)

6.00 11238.75 instruments on the block counter. The work involves termination of cables on the test panel and block counter, block wiring, interconnection between test panels and block instrument by underground signaling cable and painting the instrument as per the instructions of Railway representative at site.(Supply of block instruments, block counters and underground cables i s not covered in this schedule).[Phynolic sheet f o r fixing terminals, wire PVC 16/0.2mm copper, 3/0.75mm, paint, and a l l other miscellaneous materials required f o r the work shall be supplied by the contractor].

3.00 33631.06 Non-Interlocked working of Signals and Points, such as erection and wiring of temporary relay racks and wiring of relays, SM's slide instruments, wiring alterations in the cable termination rack, apparatus cases, signals, Control panel etc, as per the instructions of Railway representative at site.(Supply of relay rack, relays, and SM slide instrument is not included in this schedule).[All other miscellaneous materials required for the work shall be supplied by the Contractor]. SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

3.00 t e le p h o n e communication a t stations/ tents as p e r t h e instructions o f Railway representative at site. The PA system and magneto telephones will be returned to the contractor after t h e completion o f NI working. Signalling cables available may be used for the communication.(Hiring of P A s y s t e m equipments and magneto t e l e p h o n e s s h a l l b e d o n e b y the C o n t r a c t o r ) [ A l l o t h e r miscellaneous materials required for t h e w o r k shall be supplied by the Contractor]. (Per Unit= Per set per day)

10.00 crank handle o r o n suitable fixtures at station/apparatus c a s e , p r o v i s i o n of economiser push switch with locking facility, wiring w i t h w i r e P V C 16/0.2mm copper, provision of teakwood terminal box covered with decolum along with locking facility and painting.(Supply of electric key transmitter and crank handles is not covered in this schedule). [wire PVC 16/0.2mm copper, wire wound resistance, decolum covered terminal box with locking facility b y using 2 5 m m thick teakwood, b o l t s a n d n u t s , paints, push switches, p a d l o c k s a n d other miscellaneous materials required f o r this w ork shall be supplied by the contractor].

12.00 termination r a c k s a l o n g w i t h a l l the terminals, fuse blocks, relays, with jacks, holding clips etc., 50 way boards, terminals, connecting wires, cables etc., carefully without causing any damage, accounting and stacking them neatly at a place as instructed by Railway representative at site. After releasing, the fl o o r s h a l l b e l e v e l l e d and cement plastered"

6.00 different types including tail cables, carefully without causing any damage, accounting and stacking them neatly at a place as instructed by Railway representative at site.

12.00 STOP board/Warning board/ LEGEND boards along with rails, accounting and s t a c k i n g them neatly a t a p l a c e as instructed b y Railway representative at site. Also the resultant pits shall b e re- surfaced a n d consolidating by ramming and levelling"

90.00 Half/ Quarter size) without damage after releasing the shelf planks, Terminal blocks, Fuse Blocks, Terminal Boards, Relays of all t y p e s E K Ts , S e c o n d a r y Cells, power equipments, ' E ' t y p e l o c k s , e t c . , and breaking t h e concrete foundation. After releasing, the resultant pits are to be closed and consolidated by ramming and levelling. The released materials shall be accounted and stacked a t a p l a c e as instructed by Railway representative at site. SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

36.00 existing c a b l e termination b o x e s , after releasing the base plank, Terminal blocks, Fu s e Blocks, Terminal Boards, c u t rails, pipes, etc., closing t h e resultant pits and consolidating it by ramming and levelling. The released materials shall be accounted and stacked neatly at a place as instructed by Railway representative at site.

3.00 including base plank, a n d other gadgets connected very carefully without causing any damage to the panel, accounting and stacking them neatly at a place as instructed by Railway representative at site. The resultant pit in the flooring shall be removed of all cable bits, levelled and cement plastered

36.00 Colour light Signals complete (upto 4 aspects) with or without Route Indicators, c a l l i n g on signals, shunt signals etc., carefully without any damage to the gadgets, accounting and stacking them neatly at a place as instructed by Railway representative at site. The work includes breaking t h e concrete foundation,closing t h e resultant p i t and resurfacing it by ramming and levelling.

36.00 machines ( a l l t y p e s ) including ground c o n n e c t i o n s a n d o t h e r accessories available complete without any damage to the gadgets, accounting a n d stacking them neatly a t a place a s instructed by Railway representative at site.

3.00 stands available in the battery room along with connecting strips, wires and terminal boxes carefully without causing any damage to t h e batteries, accounting and stacking them n e a t l y a t a p l a c e as instructed by Railway representative at site. After releasing any holes in the walls/ flooring shall be filled with cement mortar and plastered.

6.00 types), B l o c k counters, batteries, block filter, block bell equipment etc., carefully w i t h o u t a n y d a m a g e , accounting and stacking them neatly at a place as instructed by Railway representative at site

12.00 signals along with surface base, signal post etc carefully without a n y damage, accounting and stacking them neatly a t a placea s instructed b y Railway representative a t s i t e . T h e w o r k also includes breaking and removal of concrete foundation and refilling of the resultant pit by ramming and levelling."

300.00 stumps and terminals after releasing all t h e bond wires. T h e released materials shall be accounted and stacked neatly at a place as instructed by Railway representative at site. SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

3.00 12640.13 including equipment s t a n d s , terminal boards, power panel etc., i n t h e power r o o m carefully without c a u s i n g any d a m a g e t o the equipments after disconnecting a l l the supply wires. The released equipments shall be accounted a n d stacked a t a place as instructed by Railway representative at site. After releasing a n y holes i n t h e walls/flooring shall b e fi l l e d w i t h cement mortar and plastered.

30000.00 r o a d a s p e r t h e instructions o f Railway representative a t s i t e . T h e w o r k also includes loading a n d unloading o f the materials a)Transportation o f Signalling materials upto 100kms

10500.00 more than 100km

72.00 or other machineries for regarding and levelling the formation, dismantling any infringing structures, c l e a r i n g and removing debris etc., with all leads and lifts etc., complete and as per the instruction of Railway representative at site. Total 31974372.55

Item Breakup - B-SUPPLY-B

9.00 Meters made out of 50mmX50mmX6mm thick MS angle POWDER COATED with stainless steel nuts and bolts for fixing the racks with suitable holes for hylem sheet complete as per standard practice with tripod bases and reel insulators. Cable ladder of 400mmx2000mm be provided at both sides with angle size 40mmx4mmx5mm with supporting flat of size 25mmx5mm.

900.00 made up of PBT as per RDSO Drg.No. SA. 23756/ Adv/Alt.3, confirming to Specification No. IRS.S.75/2006 (Rev.2) or latest.

750.00 Fuse holders for Railway signalling, Rated voltage 240 AC/DC to Specn. No. IRS S.78/92 (IRS-S-78/97 Tentative) IS:13703 (part 2/sec2):1993 suitable for E1 fuse 20Amps SC-20 Holder Safe Clip / knife edge type size E1 (R-SS) amp. Fuse Block for Fuse Catridge

105.00 per Specification.No.IRS :S-89-2013 ver 1.0 or latest. Charger shall be of 10Amp output capacity suitable for charging 80AH battery and No. Of Lead acid cells, 2/3/4.

3500.00 110 mm Outer Dia, 10 mm Wall Thickness, along with one coupler for every 6 Meters as per specification No. IS 4984: 2016 with latest amendments and Material Grade:PE 80. SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

3.00 941760.00 counter( HA- SSDAC) with Dual Track Sensor Devices as per RDSO specification No. RDSO/SPN/177/2012 version 3.0 or latest (Phase Reversal Type) as per details given below a) Configuration - 2 DP 1 section b) Length of cable required with each track device- 15 mtrs

1.00 210264.00 Digital Axle Counter as per Specification No. RDSO/SPN/177/2012 (Version - 3) or latest, consisting of :- (i) Portable Data Analyser (Downloading Event Logger Data for analysis and report generation) - 1 No. (ii) Pure Sine Wave Digital Multi-meter Fluke Make (Model-1871) or Rishab Make (Model-28S) - 1 No. (iii) Extender Card - 1 No.(iv) Dummy Wheel - 1 No. (v) Ring Spanner (17-19, 24-26) - 1 No. each (vi) Open End Spanner (17-19, 24-26) - 1 No. each (vii) Socket Spanner with Handle - 1 No. (viii) Torque Wrench (Jaicom JPR or equivalent 88 NM_ - 1 No. (ix) Screw Driver No. 902 or as directed by Engineer-in- Charge - 1 No. (x) Screw Driver No. 935 or as directed by Engineer-in -Charge - 1 No. (xi) Marking Jig for Drilling - 1 No. (xii) Dummy Load to check Power Supply (Resistive) - 1 No. and any other additional specialized Tools suggested by RDSO Approved OEM required for Trouble Shooting and Maintenance of Equipment

material Maintenance Free Earth as per RDSO Spec No. RDSO/ SPN/197/2008 or latest and as per relevant Technical specification

for Metre interconnecting earth electrodes

250.00 insulated Copper Cable as per IS: 694 for connecting Main Earth Electrode to MEEB in the equipment room. Color: Green

250.00 insulated Copper Cable as per IS: 694 for connecting MEEB to SEEB and SPDs to MEEB. Color: Green

250.00 insulated Copper Cable as per IS: 694 for connecting SEEB to all equipments. Color: Green

3.00 45835.00 consisting of Franklin rod of 16mm dia, single prong spike made of copper of length 600mm. Appropriate reducer/coupler for connecting Franklin rod and GI mast, GI mast approximately 1.5 inch dia, 6 mtr length with flanges for installation of franklin rod with all supporting accessories, such as guy rope, U-bolt, thimble, adjustable clamp, D- shakle, hook etc.

180.00 down conductor with all supporting accessories.

3.00 131287.00 Channels- 110V AC, 2 Channels- 110V DC , 6 Channels- 24V DC) as per RDSO Spec./256/2002 or latest with 6 digit counter. SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

3.00 measurement upto 200A AC/DC True RMS measurement for AC voltage & current. (Large jaw opsize of 18mm ) Model: FLUKE 362/Rishabh or higher specification.

: well/slimline 4S )

3.00 make or better of App. 5 feet height.

450.00 various drawing with Colour (Power board Foot diagram,Relay index chart,Station Rule Diagram, FTOT Particulars, etc), as per instructions of Site In-Charge Railway Representative.

90.00 maintanance registers for SSDAC, point machine, track circuit etc. (100 Pages each of 75 gsm paper)

150.00 Themistor standard 1434 with rating -2 Amps, make LITTLE FUSE, FUZETEC, TYCO, BOURN, RAYCHEM or Better.

54.00 Polyethylene Duct (PLB-HDPE), 40/33 mm Dia, along with End Cap, End Plug, Cable Sealing Plug and Couplers, as per RDSO/SPN/TC/45/2013 Rev.2 (upto Amdt.2) or latest

Termination WAGO/Pheonix/Elmex make or similar disconnecting Terminals blocks of size 1500mm x 500mm x 200mm thickness 1.6mm (16 SWG) 150 numbers of disconnecting terminal block with accessories. (The box should be divided in to two compartments 500 mm from TOP with door arrangement including locking, and bottom 1000mm closed fully with screws WAGO/Pheonix/Elmex terminals suitable for cable dimensions maximum of 2.5 sq.mm. Provision of easy and ensuring aesthetics.

11.00 terminals of Wago/Pheonix/Elmex make or similar

32.00 specificaiton No.IRS-TC 77/2006 Revision1 or latest for quad cable. Total 15324491.00

Item Breakup - C-EXECUTION

9.00 suitably concreting tri-pod bases and reel insulators with "J" bolts and nuts. Tripod and other supporings are to be painted in 2 coats with enamel. SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

3000.00 Method based on RDSO Report No. BS - 105. This also includes insertion of HDPE Pipe of 110mm Outer dia in the Bore drilled.(Supply of HDPE Pipe is not included).

3600.00 power cables and internal wiring on terminal/ fuse blocks in cable termination Rack at relay room. The work includes fixing of all new cables by teakwood clamp on teakwood base plank, fixing of Hylem sheet 10 mm thick for terminal board , varnishing all teakwood items, fixing of terminals/ fuse blocks on the terminal board, drilling of necessary holes, termination of cables, wiring, identification of cables using aluminium tags with letters punched neatly, as per approved circuit diagram and cable plan, painting of particulars on sleeves . After terminations are over, cable entry at the bottom shall be closed with , cement plastered, the inter-space filled with sand upto base level and the bottom surface shall be sealed with sealing compound. Cable armour to be soldered to earth.(Supply of cable termination racks is not included in this schedule). [All bolts and nuts with washers, Hylum Sheet 10 mm Thick, cement, sand, stone jelly, Teak wood base , paints and all other miscellaneous materials required for the work shall be supplied by the contractor]a. Termination on 25/60mm PBT terminals {Per Unit-Per Terminal}

3.00 50502.00 Single Section digital Axle counter (SSDAC) with High Availability. HA-SSDAC to be installed, wired, tested and commissioned by OEM as per guidelines issued by RDSO, wiring discipline should be as per RDSO TAN No. STS/E/TAN/6001 Version 1.0 or latest. The pre- commissioning checklist issued by RDSO for SSDAC to be prepared by OEM and jointly signed by OEM & Railway. Before commissioning of HA-SSDAC, OEM should submit site installation certificate.

300.00 parallel at a separation of 8 cms each to a depth of 150 mm in the platform surfaced/tiled floor for laying cable.

1500.00 10mm Thickness along with collars in trenches at places of platform cutting etc., and wherever required as per the instructions of site engineer.

600.00 pipe/DWC/HDPE pipe in which cable is already laid to a size of 300*300mm with 1:3:6 mortar. (All the matetrials required for the work should be supplied by the contractor){Per Unit- RMT}

24.00 Pit as per RDSO specification No.RDSO/ SPN/197/ 2008 or latest and as per Technical Specification SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

3.00 14360.00 protection system consistng of Franklin rod, appropriate reducer/coupler, flanges and GI mast with all supporting accessories such as guy rope(6 mm GI wire),U-bolt ,thimble, adjustable clamp, D- shakle, hook etc.

240.00 strip 25X3 mm from top of the building to ground level duly securing the same to the building.

of Numbers Earth Leakage Detector 12 channel .

3.00 61450.00 to power distribution panel. This includes transportation of IPS batteries from store of Dy CSTE/CN to the site, Erection of IPS panels on teakwood planks, interconnection between panels and wiring the IPS to power distribution panel using 10 sqmm multi-strand copper cable. The wiring should be done neatly using Aluminium ladder with Phynolic sheet (Aluminium ladder, Phynolic sheet of thickness 6 mm, teak wood plank of width 150 mm and thickness 25mm, 10 sqmm multi-strand copper cable and all other miscellaneous materials to be supplied by the contractor).

93.00 Full/Half location boxes, by carrying out the earth work around the foundation, ramming of the earth, carrying out masonry work from bottom of earth work using country stones and cement masonry to prevent the earth from slipping down the bank.

3.00 termination of cables on Wago/krone connectors as per the instructions of the site Engineer.

of disconnecting terminals of wago/phonix/elmex make or similar and termination of cable at the station/LC gates etc. This includes fixing of Quad/PIJF cables and CT box on the wall.

24.00 Shrinkable type complete for 6 quad cable. After the jointing the through cable has to be tested for insulation resistance and loop resistance in presents of Railway Engineer and in case of any defects the jointing has to be done at free of cost by the contractor. [Heat Shrinkable jointing kit conforming to RDSO specificaiton No.IRS-TC 77/2006 covered in the supply portion has to be used for this purpose. The Contractor should supply all other small items free of cost which are required for making a joint. Only gas blower to be used for blowing SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

3.00 70094.00 staff round the clock to attend to teething trouble of the installation along with SSE/JE(Sig) after the installation has been brought into commissioning.The work includes routine maintainence,failure restoration as per the direction of the SSE/JE(Sig). Total 9589275.50

Item Breakup - D-SUPPLY AND INSTALLATION

3.00 98035.00 Core Plan, Cable Termination Rack Particulars, Location Box Particulars, Power Supply Diagram, Track Circuit Bonding Diagram and/or any other drawing on Auto- CAD in A2/A3/ A4, etc. size (as per instructions of Engineer in- charge). Initially Contractor shall submit 2 sets of 'AS PLANNED' documents complete for approval of Railways. One set is returned either duly approved for making a fair copy or for re-submission for approval after incorporating the changes as required by railways. After preliminary approval, execution of work shall be carried out at site. After Completion of work, 2 sets of 'AS MADE' Check Prints are submitted for Administarative approval. Railways will return one set to the contractor duly approved with alterations/corrections if any. The contractor shall incorporate Railways alterations/corrections in the tracings without any deviation and submit all tracings complete in all respect along with its soft copies in USB Pen Drive and 6 sets of final completion drawings in properly bound booklets. [For Centralized Electronic Interlocking Stations/Small Stations]

3.00 58338.00 Change over arrangement at SM room. CLS panel of size 800x500x275mm powerd coated of MS sheet thickness 1.6mm as per RDSO specification No TI/SPC/PSI/CLC/0020 . SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

and Supply Distribution Panel for IPS using Hylem sheet 10 mm as per site requirement and erecting it using MS angle clamp 65mm X 65mm X 8mm, HRC fuse block, Mains control switch, ammeter by-pass switch, voltmeter, ammeter, PBT terminals 60mm and wiring the same using wire PVC 7/1.40mm as per approved power diagram. This also includes termination of power cables using teakwood clamp of size 25mm X 60mm X 150mm on a base plank of 25mm thick 150mm width. (MS angles 65mm X 65mm X 8mm, Hylem sheet of 10 mm Thickness, as per site requirement, bolt and nuts required for manufacture of power panel, HRC fuses, box and carriers, teak wood clamp, wire 7/1.40mm, PVC casing and capping and all other miscellenous materials will be supplied by the contractor, Supply of PBT terminals 60mm is not included in the schedule.)

Installation, Commissioning of Copper Plate Earthing System complete with provision of (i) Copper plate 300mm X 300mm X 3 mm, (ii) Earth Pit 6 ft depth filled up with charcoal 10 kg & salt 25 kg in alternate layers up to 2 ft from bottom, (iii) Water funnel on Perforated GI pipe of length 4.5 ft., (iv) Cast Iron top plate 12" x 12" (v) Drawing of copper - earth from earth to location with 25 mm x 3 mm copper strip for termination(all miscellaneous materials to be supplied by the contractor)

6.00 Goods Warning Boards as per practice & SEM(Angle/Rail is to be supplied by Railway).

21.00 Calling-On/STOP/BSLB/Legend boards as per practice & SEM (Angle/Rail is to be supplied by Railway).

4.00 Key Box at Interlocked LC Gates, made of Teak wood with Glass fronted door as per drawing 03/91. Polishing on all exposed surface and for with EKT inside the box. Micro push switch of L&T make with 2NO+2NC contacts and veeder counter non-reset type and wire them as per the approved circuit diagram. The box should have hinges and pad locking arrangements with one No.40 mm Navtal- Lock with duplicate keys and key chain with label. (All materials except EKT are to be supplied by the contractor).

5400.00 channel of size, Width 240/340 mm, Height 155/230 internal/external, length 1 m produced of polyolefin with Fire protection class k-1 in accordance with DIN-53438 Part II for laying Signalling/Telecom cables, channel attachable to each other with male-female swallow tail connectors and having suitable detachable cover SWR-CONST-HQ-S AND T/SOUTH WESTERN RLY

4500.00 Capping (RCC Duct) of 500mm Width as per Drg. No. SDO/Cable laying/ 007 (Annexure-10), as detailed in document No. RDSO/SI/G/2010 Ver.1.1 or latest on 'Guidelines on signalling cable laying'

3.00 34673.00 Handle Cum Key Lock Relay Box (of MS Sheet) along with LEDs, with approved type push buttons, Wago or similar Disconnecting type Terminal Blocks inlcuding DIN rail etc., as per tentative drawing enclosed. Installation, fixing and wiring of boxes for Key Lock Relays to be carried with Contractor's wiring and fixing material. The work shall be carried as per the instructions of site engineer.

300.00 capping/PVC pipe of minimum 25 mm size or higher as per requirement at site on the wall/floor etc., using bends, coupler and T joints and flexible pipe wherever necessary with fixture in the OFC room from equipment rack to common termination and from OFC room to SM room/Reservation office /Data logger/FOIS room etc. (All required material for fixing to be arranged by the contractor) Total 21803241.00

Item Breakup - A1-SOR TELE

6.00 joint chambers with dry sand mixed with anti-termite chemical as required in specification up to 400mm height and the cover is refixed in position.

6.00 10302.00 Joint including Splicing (24 Fibre) inside already prepared jointing pit. This does not include provision of Joint chamber, top plate & back filling. The joint Enclosure shall be as recommended in the Technical specification. Total 65412.00

D-SUPPLY AND INSTALLATION

E-ELECTRONIC INTERLOCKING

G-FIRE DETECTION AND ALARM SYSTEM

H-NON-SOR SIGNAL

H1-(NON SOR) TELE