WELCOME MAINTENANCE AND OTHER MISC B/R WORKS INCLUDING CERTAIN ELECTRICAL REPAIR WORKS AT OMQ AREA

Amount

SCHEDULE A BOQ

Complete removal of existing water proofing treatment and expose of top surface of RCC slabof any thickness, any type by stripping out old tar felt over roofs, parapets, chimney stacks etc laid horizontally or vertically including taking out layer of cement plaster etc and cleaning the surface with water and using wire brush including removing debris to out side the MoD land and providing following :- (a) Dismantling existing cement concrete/roof tiles on roof including removing debris to out side MD land as directed. (b) Bring upto the slope by providing filling of light weight materials sch as cinder, light weight concrete etc as required, and then providing PCC 1:2:4 type B1 of average thickness of 50mm. (c) Rendering 10mm thick in CM 1:3 on concrete roof surfaces and finish the surface even and smooth without using extra cement including mixing water proofing compound @ 2% by weight of cement. (d) Apply a coat of bituminous primer confirming to IS-3384@ 0.4 ltr/Sqm on newly plastered surface after curing as per IS-456 and dried. (e) After the primed surface has dried, apply a coat of hot blown bitumen(85/25 penetration) confirming to IS-702 @ 1.2 Kg/Sqm of the surface. (f) Providing APP modified water proofing as approved by GE weighing not less than 4kg per sqm unrolled over the bituminous coated surgace with 100mm over laps, the overlap shall be sealed by flame as per manufacture instructions complete. (g) Over the APP membrane, apply evenly a tack coat of hot air blown bitumen of grade 85/25 at the rate of 1.20 kg per sqm including cleaning of surface. (h) Applying a coat of aluminium paint at the rate of 100 gm per sqm as per manufacture instruuction over bituminous layer complete all as directed. Note : (i) Care shall be taken to avoid wrinkle and air gaps while sticking membrane to the bitumen applied surface.

Taking down cement plaster on brick or stone walls, or concrete or ceilings etc., including raking out joints, hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises, removal and depositing serviceable materials where directed and leaving the work clear of any plastering and M&L for rendering 10mm thick on fair faces of brick work or concrete in CM 1:4 complete all as specified and directed.

Dismantling existing cement concrete on roof and removal to a distance exc 1.5 KM but not not exc 5 KM and deposited as directed.

M&L Plain cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in roof kerbs,benching rounded or chamfered on edge all as specified complete all as directed.

Minor repair to aluminum/ glass doors, windows, partitions and making good the same (i.e. Handles, hings, rubber beadings, clips etc) complete all as specified and directed.

Taking down chowkats or frames with shutter exc 1.5 Sqm and n exc. 4 Sqm each without taking off shutter from the frame.

Resecuring without taking down chowkhats or frames but with shutters without taking off shutters from the frames) not exc 1.5 sqm each

Resecuring without taking down chowkhats or frames but with shutters (without taking off shutters from the frames) exc 1.5 Sqm but n exc 4 Sqm each.

Second class hard wood plain, solid, straight Chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

Factory made 35 mm thick flush shutter solid core construction, with block board core and plywood face panelson both side converedwith decorative face veneer with lipping/frame to match.

Taking down steel tubing 15mm bore and connections including cleaning and refixing of old GI tubing 15mm bore including connections in new or old position (wall, ceiling & floor). Note :- The unit rate is included for all to be fittings for re-connection.

Taking down steel tubing 20mm bore and connections including cleaning and refixing of old GI tubing 20mm bore including connections in new or old position (wall, ceiling & floor). Note :- The unit rate is included for all to be fittings for re-connection.

Brass 4 liver mortice lock vertical type 100mm size including taken down existing one complete all as specified and as directed by Engineer-in-Charge.

Doom grating 125mm dia with waste hole of PTMT(minimum weight 40gms) Including taken down existing one complete all as specified and as directed by Engneer-in-Charge.

40mm dia waste fittings, brass, chromium plated for glazed ware sink basin etc, with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixing Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

40mm low density polyethylene (LDPE) pipesof pressure rating 6 kpf/sqcm for sink Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

Sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm in repairs all as specified and directed. Make : M/s Diamond / Nirali / Amco / TATA.

Dismantling floor, floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and Material and labour for Glazed ceramic coloured tiles 450 x 300 mm x 7/8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles on vertical surface such as dado including 10mm thick 1:3 backing coat complete all as specified and directed.

Dismantling floor, floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and Joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile of size exc 0.06 Sqm but n exc 0.16 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incuding screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) complete all as directed.

Note for item No 19 & 20 :- The manufacturer's test certificate and individual test certificate of Tiles must be submitted for approval by the concerned authority prior to installation.

PVC (SWR) P trap 125/110 mm bore Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

PVC (SWR) S trap 125/110mm bore Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

Vitreous Ware wash down water closet (Pedestal), white (EWC) Plastic seat of same colour of WC, closed pattern with flat bottom, and cover and Mild steel chromium plated hinging device including taking down the existing fitting complete all as specified and directed.

32 mm dia Waste fittings, brass, chromium plated for basins with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixing Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

32 mm low density polyethylene (LDPE) pipes of pressure rating 6kgf/sqcm for WHB Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

20 mm outer dia of pipes 3-layer PP-R (Polypropylene random copolymer) pipes concealed pipes SDR 7.4 (PN-16 @ 20°C) UV stablised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings, including taking down existing pipe of any description complete to walls, ceilings or in floors etc. all as specified and directed. Make : SFMC, Reliance Industries, KPT

Note :- (a) The unit rate shall be include for taking down existing GI pipe and connections and all fittings as directed.

(b) The unit rate shall be include the cost of short lengths, with all pipe fittings such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc and fixing accssories such as pipe hooks, screws clamps etc

(c ) Wall thickness of pipes shall be all as per IS : 15801

CP Hand shower (Health Faucet) with 1M Flexible Tube with 8mm bore wall Hook with N.R.V (Back Flow Preventor) CAT Part No-S. No-ALD CHR-579 Jaquar equivalent in ESSCO/ Kohler as per list of makes Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

CP pillar cock pressmatic auto closing fancy type 15mm dia CP with capstan head screwed down high pressure screwed for iron pipe CAT Part No-Sl. No-PRS-031 Jaquar or equivalent in Parryware ,or as per list of makes Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete all as specified and directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm fixed including taken down existing one complete all as specified and as directed by Engineer-in-Charge.

MS flat iron hold fast Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

Cutting holes in stone/brick wall exc half brick and n.exc one brick in cement mortar for inserting hold fasts and making good desmantled portion in cement mortar 1:3 or 1:2:4 type B-1 concrete as required.

Taking down of aluminum/ glass doors carefully and re-fixing in same opening including necessary repairing/ cleaning/ greasing etc and make the same fully functional all as specified and directed.

Resecuring of easing & adjusting without taking down shutters of n exc 1 sqm each

Resecuring or easing & adjusting without taking down shutters of exc 1 Sqm but n exc 2 Sqm each

Factory made 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); all as specified and directed.

Two coats of synthetic enamel paint over a coat of pink primer over new wooden surface of any description over 10 CM width or girth including preparation of new surfaces.

Preparation of old painted wooden surface of any description and applying one coats of synthetic enamel paint, not otherwise described over 10cm width or girth.

Note :- (a) All synthetic enamel paint, plastic emulsion paint shall be of 1st quality manufactured by the standard firms of make as specified.

(b) The contractor shall inform the GE, within three weeks of the acceptance of the tender, the brand/names of the manufacturers of paint proposed to be used in the works and submit samples thereof and obtain prior written approval of GE before their use in works.

(c) The contractor shall when so required by the GE, produce certificate from the manufacturer or their representative to establish that the brands of paints purchased by the contractor from them, satisfy the requirements of the relevant Indian Standards. Tint of paint, will be approved by the GE.

(d) Paints shall be obtained direct from approved manufacturer or from their authorized agents only of respective brands mentioned below and brought to site in sealed containers. The paint so procured shall be of first quality of any approved make as per list of makes specified. i. Berger Paints (Luxol), ii. Jenson & Nicholson (Brolac), iii. Shalimar Paints(Superlac), iv. Goodlass Nerolac (Nerolac), v. Asian Paints(Apcolite)

(e ) Unless otherwise specified the tints of paint shall be as approved by the GE

(f) The contractor shall submit samples of the paints proposed for the work along with results of tests conducted in approved laboratory as directed by the Engineer-in-Charge for approval.

(g) The surface shall be thoroughly cleaned and dusted. All dirt scales oil and grease shall be thoroughly removed before painting is started. The prepared surface shall be inspected and approved by the GE before painting is commenced. The weather shall not be foggy/rainy, dusty or windy. The suitability of the weather will be determined by the Engineer-in-Charge.

(h) No hair marks from the brush or clogging of paint buddles shall be left on the work. Surface shall ordinarily not be painted until it has dried up completely. Trial patches of paint shall be laid at intervals to check if drying is satisfactory.

Factory made Solid PVC Door Shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified.

Black Granite slab 18 to 20mm thick machine cut, pre-polished , bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite including cutting a hole in the granite slab for gas pipe etc to any shape and polishing of exposed edges in cooking platform complete all as required site (Overall size of the slab shall be measured) complete. The size of slab shall be single piece and exposed edges shall be moulded. Note :- The unit rate is deemed to be included for dismantling of stone slab and tiles laid bedded and pointed in any mortar of any description or thickness in floors

Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations.

Brass 4 lever cupboards locks grade I size 65mm complete all as specified and as directed by Engneer-in-Charge

Brass 4 lever cupboards locks grade I size 65mm Including taken down existing one complete all as specified and as directed by Engneer-in-Charge

Stainless steel thali basket of size 600x 500x 100mm Including taking down the existing one complete Make : Butterfly or equivalent make as per list of makes)

Stainless steel cutlery basket of size 530 x 505 x 100 mm Including taking down the existing one complete Make : Butterfly or equivalent make as per list of makes)

Sink without drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste, including bedding in cement mortar to dwarf wall or including fixing with stone slab using approved adhesive overall size 495mmx 420mm and bowl size 410 mm x 330mmx 160mm, fixed in repairs complete all as specified and directed. Make : M/s Diamond / Nirali / Amco / TATA.

Preparation of old decorated, plastered or pointed surfaces of wall and applying one coat of oil bond distemper including removal of nails and filling the gaps with putty for making the surface good complete all as specified and directed.

Preparation of old plastered or unplastered surface of ceiling and applying one coats of white wash

Floor door stopper of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor 150mm complete all as specified and as directed by Engneer-in-Charge

Floor door stopper of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor 150mm Including taken down existing one complete all as specified and as directed by Engneer-in-Charge

40 mm dia cupboard knobs fixed with nut, screw and washer of brass polished complete all as specified and as directed by Engneer-in-Charge

40 mm dia cupboard knobs fixed with nut, screw and washer of brass polished Including taken down existing one complete all in repair as specified and as directed by Engneer-in-Charge

Stainless steel spring hinges of size of approved pattern and make suitable for base/wall unit of modular kitchen Including taking down the existing one complete (Make : BIR SS or equivalent make as per list of makes)

Magnetic catches with 8mm dia steel ball and brass body and striking plate including letting in & Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

Mild steel work in framed work such as grills and similar work including framed guard bars, barred iron doors, ladders, framed balusters etc., including of fixing of sheet steel or other covering to doors etc., to be prepared for hanging /sliding with or including either hooks or hinges or steel hanging door fittings etc., confirming to Fe 410-0 or Fe 310-0 work complete including Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

Factory made UPVC three track sliding Window frame having 2 tracks for glass shutter and 1 track for mosquito sash made of upvc profile section of size 73mm x 42mm (wxh) having outer wall thickness of 2.0mm(+/-0.2mm). Sliding glass shutter shall be made of UPVC section of size 55mm x 33mm and sliding wire mesh shutter shall be made of UPVC section of size 40mm x 22mm. All section of the frame, sash, transom & mullion, as applicable, shall be duly reinforced with G/J/U/O shape galvanised mild steel section of required thickness considering structural / wind load requirement. System shall be provided with the suitable upvc bead for glazing of the system & fitted with inner & outer EPDM seal gaskets. Clear Glass of Saint Gobain / Modiguard make with thickness of 4mm and stainless steel wire cloth of 0.19mm nominal dia. All welded joints are to be neatly trimmed & feature grooved/raised nib finish so make the finished product free from all sharp edges & burrs. All the corner / mullion / transom joints of the frame and sash shall be mitered cut & fusion welded without any mechanical joining. System shall have adequate drainage mechanism to permit the escape of water from horizontal member beneath each sealed unit. System is to be provided with proper operating & locking hardware mechanism. Window locking system will be either both side push lock system or semi-circle locking system in centre. Complete window shall be fixed in to the existing pre finished aperture, by drilling and fixing through the outer frame using quality fasteners & silicon glue is applied to fill up the crevice between wall and window frame for leak proof installation including taking existing one complete all as specified. Note: - The contractor will have to submit 5 years warranty certificate for upvc profile and 1 year warranty certificate for hardwares.

Factory made UPVC Ventilators design will be like top part fixed with exhaust fan provision and bottom part with fixed louver strips.Ventilators frame made of upvc profile section of size 45mm x 43mm (wxh) having outer wall thickness of 2.0mm(+/-0.2mm). Wherever required /specified, system shall havev the fix mullion of size 45mm x 60mm having outer wall thickness of 2.0mm(+/- 0.2mm). All section of the frame,transom & mullion shall be duly reinforced with G/J/U/O shape galvanised mild steel section of required thickness considering structural / wind load requirement. System shall be provided with the suitable upvc bead for glazing of the system & fitted with inner & outer EPDM seal gaskets. Pinhead Glass with thickness of 4mm required for fixed & louvers strips. All welded joints are to be neatly trimmed & feature grooved/raised nib finish so make the finished product free from all sharp edges & burrs. All the corner / mullion / transom joints of the frame shall be mitered cut & fusion welded without any mechanical joining. System shall have adequate drainage mechanism to permit the escape of water from horizontal member beneath each sealed unit. System is to be provided with proper operating & locking hardware mechanism. Complete ventilator shall be fixed in to the existing pre finished aperture, by drilling and fixing through the outer frame using quality fasteners & silicon glue is applied to fill up the crevice between wall and ventilator frame for leak proof installation including taking existing one complete all as specified. Note :- The contractor will have to submit 5 years warranty certificate for upvc profile and 1 year warranty certificate for hardwares.

Anodised aluminium frame powder coated for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc Including taken down existing one complete all as specified and as directed by Engineer-in-Charge.

9mm thick prelaminated particle board, interior grade, prelaminated both sides with decorative choice lamination fixed with screws to aluminium frame Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

Aluminum handles cast type anodised 150mm long complete all as specified and as directed by Engineer-in-Charge.

Aluminum handles cast type anodised 150mm long Including taken down existing one complete all as specified and as directed by Engineer-in-Charge.

Aluminum handles cast type anodised 100 mm long Including taken down existing one complete all as specified and as directed by Engineer-in-Charge.

Plate rack of size 65 cm x 96 cm made of stainless steel,fixed in repairs complete all as specified and directed.

Plastic water closet seat for EWC with flat bottom and cover and mild steel chromium plated or alluminised hinging device fixing Including taken down existing one complete all as specified and as directed by Engineer-in-Charge.

CP 2 way bib cock with wall flange fancy type screwed down screwed for iron pipe in repairs 15mm bore CAT Part No-Sl. No-CQT-23041 Jaquar or equivalent in Parryware ,or as per list of makes Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

S&F of PVC Connection 15mm size with PTMT nuts of length 375mm

Preparation of old sufaces of wall and applying two coats of oil bound distemper.

Preparation of old decorated plastered or unplastered surface of wall, and applying one coats of white wash on wall complete.

Glass self assembly including taken down existing one complete all as specified and as directed by Engineer-in-Charge. Make : CAT Part No-ACN-1173 continental of Jaguar series or equivalent make of Parriware /Hindware

Towel rail 24" long for wash basin Including taken down existing one complete all as specified and as directed by Engineer-in-Charge Make: (Make : CAT Part No-ACN-1111NM of Jaguar series or equivalent make of hindware / parriware.

25 mm outer dia of pipes 3-layer PP-R (Polypropylene random copolymer) pipes concealed pipes SDR 7.4 (PN-16 @ 20°C) UV stablised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings, including taking down existing pipe of any description complete to walls, ceilings or in floors etc. all as specified and directed. Make : SFMC, Reliance Industries, KPT

Note :- (a) The unit rate shall be include for taking down existing GI pipe and connections and all fittings as directed.

(b) The unit rate shall be include the cost of short lengths, with all pipe fittings such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc and fixing accssories such as pipe hooks, screws clamps etc

Towel Ring round Make: (Make : CAT Part No-ACN-1121BN of Jaguar series or equivalent make of hindware / parriware Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

Chromium plated wall mixer with provision for over head shower with 115mm long bend pipe on upper side connecting legs and wall flanges complete including taking down all as specified and directed. Make:- CQT 23281UPR of Jaquar or equivalent in Parryware /Hindware / ESS-ESS.

Vitrified Ceramic tiles 10 mm thick, dark shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer ,15 mm thick in Cement Mortar 1:6 including taking down existing tile and removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. Note : (a) Vitrified tiles are classified under group B1a of the international Standard for ceramic tiles ISO: 13006. Tiles shall be hard, dense, impervious and frost resistant. Water absorption of tiles shall be less than 0.5% and flexural strength (Modulus of Rupture) shall be more than 35 N/Sqmm. (b) The manufacturer's test certificate and individual test certificate for tiles must be submitted for approval by the concerned authority prior to installation.

Vitrified Ceramic tiles 10 mm thick, dark shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer ,10 mm thick in Cement Mortar 1:3 including taking down existing tile and removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. Note : (a) Vitrified tiles are classified under group B1a of the international Standard for ceramic tiles ISO: 13006. Tiles shall be hard, dense, impervious and frost resistant. Water absorption of tiles shall be less than 0.5% and flexural strength (Modulus of Rupture) shall be more than 35 N/Sqmm. (b) The manufacturer's test certificate and individual test certificate for tiles must be submitted for approval by the concerned authority prior to installation.

Complete removal of existing finishes on plastered wall surfaces and applying two coats of oil bound distemper over a coat of primer including two coats of putty as 1st coat of putty (1.50mm thickness) and 2nd coat of wall putty (1.0 mm thickness ) all as specified and directed.

Wall mounted Shower Arms 190mm long flat shape for wall mounted shower with flange including taking down complete all as specified and directed (Make :CAT Part No-SHA-483 of Jaguar or equivalent make of parriware /hindware..

Overhead Shower ø120mm Round Shape Single Flow (ABS Body Chrome Plated with Gray Face Plate) with Rubit Cleaning System In repairs complete all as specified and as directed. (Make :CAT Part No- OSH-1709 of Jaguar or equivalent make of parriware /hindware..

CP sink cock with swinging casted round shape spout screwed down screwed for iron pipe in repairs 15mm bore CAT Part No-CQT-23347 Jaquar or equivalent in Parryware ,or as per list of makes Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

4mm figured glass pin headed type glazing with oil putty in squres n.exc 0.5 Sqm in each pane.

25mm dia mild steel powder coated drapery rod out to length required without joint in between and fixed at openings as directed

25mm dia mild steel powder coated drapery rod out to length required without joint in between and fixed at openings Including taken down existing one complete all as specified and as directed by Engneer-in-Charge

Mild steel powder coated brackets for holding the drapory rod and fixed to wall with MS screw all as specified and as directed.

Mild steel powder coated fancy type brackets fixed at both the end of drapery rod of same colour and type of drapaery rod Including taken down existing one complete all as specified and as directed by Engneer-in-Charge

False ceiling using GI snap grid size 60x60cm with main runner 38x24,wall angle & cross tee 29x24mm wall angle 24x24mm suspended with 4mm dia GI Wire fixed with steel dash fasteners carrying max load upto 8.1 Kg/Sqcm with 4mm thick designer ceiling board Including taken down existing one complete all as specified and as directed by Engineer-in-Charge (Lake & Hill) all as per Everest regular T-2430 or equivalent. Make-Ramco/ Charminar/ Armstrong

Preparation of old painted surfaces of steel applying one coat of synthetic enamel paint over 10 cm width or girth, not otherwise described over 10 cm width or girth.

M&L two coat of synthetic enamel paint over a coat of red oxide primer on new steel surfaces over 10 cm width and girth including preparation

6mm thick frame less bevelled edge mirror fixed with steel stud Including taken down existing one complete all as specified and as directed by Engineer-in-Charge.

PVC Dual flush ceramic colour, low level, 10 litres capacity, star white with inlet float ball valve, PVC flush pipe and handle, making proper fixing and hanging arrangements Including taken down existing one complete all as specified and as directed by Engineer-in-Charge Cat Part No 21029 of hindware or equivalent

PVC body cabinet mirror of size 500 X 400 MM of approved design and pattern Including taken down existing one complete all as specified and as directed by Engineer-in-Charge . (Make: Cat Part No 556 of Prayag or its equivelent in ESSCO/ Kohler as approved by GE

Pillar taps 15mm bore dia of pipe CP with capstan head screwed down high pressure screwed for iron pipe Cat Part No CQT -23021KN of Jaquar or equivalent in Parryware ,or as per list of makes Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

Angular stop cock, valves high pressure screwed both ends iron pipe or for unioins 15mm bore dia pipe, CAT Part No G3007A1 of Parryware or or equivalent in as per list of makes Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

Stainless steel handles of size 150 mm of approved pattern and make suitable for Base/Wall unit of modular kitchen Including taking down the existing one complete (Make : Spykar or equivalent make as per list of makes)

Stainless steel plain basket of size 530 x 505 x 100mm Including taking down the existing one complete. Make : Butterfly or equivalent make as per list of makes

Stainless steel bottle basket of size 200x 508x 431mm including taking down complete all as specified and directed. Make : Butterfly or equivalent make as per list of makes

Stainless steel telescopic slider of 500 mm of approved pattern and make suitable for drawer in base unit of modular kitchen including taking down the existing one complet

5mm thick rubber beading strips of entrance doors having width exc 3CM to not exc 5CM to arrest entry insects Including taken down existing one complete all as specified and as directed by Engineer-in-Charge.

Niagara coupled closet with flushing cistern and anti microbial seat cover with all fittings complete (Make : Cat No C0262 Niagara series of Parriware or or equivalent in list of makes Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

Factory made UPVC casement door frame made of UPVC profile section of size 60mm x 58mm (wxh) having outer wall thickness of 2.0mm(+/-0.2mm) and 3 box multi chamber construction.The shutter of outward openable door shall be made of size 78 x 60mm (shutter of inward openable door shall be made of size 71 x 60mm) having outer wall thickness of 2mm(+/-0.mm). Doors will have 6mm thick partical board . Wherever required/specified, system shall have the fix mullion of size 72mm x 60mm having outer wall thickness of 2.00mm(+/- 0.02mm) . All sections of the frame ,saash,transom , & mulion shll be duly reinforced with G/J/U/O shpe galvanised mild steel section of required thickness considering structural / wind load requirement. All the corners/mullion / transom joints of the frame & sash shall be mitred cut & fusion welded without any mechanical joining. All welded joints are to be neatly trimmed and feature grooved/raised nib finish so as to make the finish product free from all sharp edges and burrs. System shall have adequate drainage mechanism to permit the escape of water from horizontal meber beneath each sealed unit.System shall be provided with the suitable UPVC beads for glazing of the system with specified/required single /IGU Glass, duly cut at correct degree & fitted with K & O type inner and outer EPDM weather seal gaskets . System is to be provided with proper operating and locking hardware mechanism as per system. Complete door shall be fixed in to the existing pre finished aperture, by drilling and fixing through the outer frame using high quality fastners & silicon glue is applied to fill up the crevice between wall and door frame for lek proof installation including taking existing one complete all as specified. Location- OMQ. Note : The contractor will have to submit 5 years warranty certificate for upvc profile and 1 year warranty certificate for hardwares.

5.5mm thick colour tinted float glass and glazing with oil putty in square exceeding 0.5sqm in each pane Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

Aluminium alloy anodised sliding door bolt 300mm long with hasp staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolt and sliding bolts of extruded section or cast-aluminium alloy complete all as specified and as directed by Engineer-in-Charge

Aluminium alloy anodised sliding door bolt 300mm long with hasp staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolt and sliding bolts of extruded section or cast-aluminium alloy Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

150mm long aluminum anodized barrel tower bolt extruded section complete all as specified and as directed by Engineer-in-Charge

150mm long aluminum anodized barrel tower bolt extruded section Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

Sheet glass 4mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete.

Removal of existing treatment,cleaning the existing surface with wire brush and water completely, including preparation and applying two coats of cement base paint over a coat of primer on external surfaces of wall and curing to CBP upto required period.

100 mm long aluminum anodized barrel tower bolt extruded section complete all as specified and as directed by Engineer-in-Charge

100 mm long aluminum anodized barrel tower bolt extruded section Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

Particle board plywood 18/19 mm thick interior fixed with screw to timber frame including taken down existing one work all as specified

12mm thick, 7 ply, plywood , grade BWR , type BB fixed to wooden frame work in wall with Nails,Including taken down existing one complete all as specified and as directed by Engneer-in-Charge

Decorative laminates of 0.90 mm thick type matt finish, colour and pattern as approved. Including taken down existing one complete all as specified and as directed by Engneer-in-Charge

Second class hard wood plain fillets square or rectangular in section exc 3Sqcm n.exc 6 Scqm wrought secure with screws.

2nd class hard wood pieces, small let in for making good where hinges etc have been removed from chowkhats or frames, joinery, etc. Including painting or oiling to match as required Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

300mm mild steel ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and as directed by Engineer-in-Charge

300mm mild steel ordinary rat tail rod pattern spring including roller and roller plate Including taken down existing one complete all as specified and as directed by Engineer-in-Charge

Brass continuous(Piano)hinge 30mm width of flap, bright finish of electrolyte complete all as specified and as directed by Engneer-in-Charge

Brass continuous(Piano)hinge 30mm width of flap, bright finish of electrolyte Including taken down existing one complete all as specified and as directed by Engneer-in-Charge

Butt hinges 100mm long medium weight cold rolled MS fixed complete all as specified and as directed by Engineer-in-Charge.

Butt hinges 100mm long medium weight cold rolled MS fixed Including taken down existing one complete all as specified and as directed by Engineer-in-Charge.

Butt hinges 75 mm long medium weight cold rolled MS fixed complete all as specified and as directed by Engineer-in-Charge.

Butt hinges 75 mm long medium weight cold rolled MS fixed Including taken down existing one complete all as specified and as directed by Engineer-in-Charge.

Taking down aluminum/copper point wiring on & including hard wood battens, surface conduit and board/ blocks etc or through conduits for light, socket or power point, fan point complete (Taking down of fittings such as switches, sockets, bells, ceiling rose, holders , regulators, light fittings, MCB, lamps etc shall be measured and paid seperately) and making good the disturbed plaster surfaces of wall, floor, ceiling and painting 2 coat of white wash/distamber to meet the existing surface and removing materials and debris to reinstate the premise neat and clean complete all as specified and directed.

M&L for point wiring using approved colour coding as per IS for one light/bell/buzzer point controlled by one switch or one fan point controlled by one switch & fan regulator with PVC insulated, unsheathed FRLS multi stranded copper conductor 1.5 sqmm (nominal area) 1100 volt grade ISI 694 marked cable for phase & neutral drawn through concealed PVC casing capping , ISI marked with and including new MS/ cast iron sunken boxes duly painted with two coats of anticorrosive paint over a coat of red oxide primer on surface in touch with wall and synthetic enamel paint over a coat of red oxide on other side, covered with 3mm thick plastic laminated sheet for mounting switches, regulators, sockets etc including 1.5 sqmm (nominal area) copper conductor PVC insulated, unsheathed, multi stranded FRLS cable as earth wire and connected to earth dolly complete all as specified and as directed. Make of Conduit : Modi/ Presto plast/ Polycab Make of Wire : Plaza/ Polycab/ Havells Note: (a) Switches, sockets outlets, blanking plate, Light fittngs, fans, bells & regulators will be measured and paid for separetely). (b) Connection of wire with switch, socket shall be through copper thumble (lugs) only.

One light point/fan/bell point controlled by one switch

All as per item No. 138 here in before but for one 3 pin socket out 5 amp on the same board

All as per item No. 138 here in before but for one switch socket outlet 3 pin 5 Amps on independent board

All as per Sl No 138 above but Wiring with 4 Sqmm copper multistranded unsheathed cable and 4 Sqmm copper cable for earth continuity conductor controlled by one 15A switch socket independently

Switch piano flush type 5 Amps 240 volts single pole one way. Make : Anchor (Model Penta PC), Havells (Reo), SSK (Topline)

Switch piano flush type 15 Amps 240 volts single pole one way. Make : Anchor (Model Penta PC), Havells (Reo), SSK (Topline)

Shuttered socket outlet 3 pin 5 amps, flush type

Shuttered socket outlet 2 in 1, 3 pin, 5 and15 amps

Modular switch 1 way 6 amp.1 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Modular switch 1 way 16 amp.1 module. Make : Legrand (Model- Arteor), ABB (Cheiron), Schneider (Ulti)

Bell push, flush type, 5 amps

Metal clad switch socket single pole and earth enclosure with two pin and earth plug with socket complete with on SP 20 Amps, 230 Volts.

Electronic fan regulator 230 volts, step type socket type, hum free 120watt. Make : Havells/ Schnieder/ Crabtree

Lamp holder, insulated body, cord grip pattern SP 230 volt, complete all as specified and as directed.

Ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body

Bell, AC, 230 volts, single pole, Ding Dong. Make : Anchor/ Cona/ Plaza

LED retrofit lamp 15W, warm white, (lumen output not less than 1350 lumens) with B-22 holder base with thermal conductive engineering plastic white colour housing and aluminium heat sink with specially designed fins clear /cool white, power factor more than 0.9, with surge protection device minimum 2KV, color temperature not less than 6000K, CRI more than 80, LED driver with constant output voltage and current at input voltage of 140 Volt to 285 Volt AC at 50 Hz, glarefree, 0 UV radiation Including taken down existing one complete all as specified and as directed by Engineer-in-Charge. Notes:- 1. The contractor shall submit to Engr-in-Charge LM-80 and LM-79 report from the NABL approved lab of LED chip used and luminaire respectively. 2. The contractor shall submit warranty certificate from manufacturer for minimum 2 years Make : Wipro cat part No. LL20-111-XXX-65NE3 or equivalent of Philips/ Bajaj

LED retrofit lamp 12W, warm white, (lumen output not less than 1350 lumens) with B-22 holder base with thermal conductive engineering plastic white colour housing and aluminium heat sink with specially designed fins clear /cool white, power factor more than 0.9, with surge protection device minimum 2KV, color temperature not less than 6000K, CRI more than 80, LED driver with constant output voltage and current at input voltage of 140 Volt to 285 Volt AC at 50 Hz, glarefree, 0 UV radiation Including taken down existing one complete all as specified and as directed by Engineer-in-Charge. Notes:- 1. The contractor shall submit to Engr-in-Charge LM-80 and LM-79 report from the NABL approved lab of LED chip used and luminaire respectively. 2. The contractor shall submit warranty certificate from manufacturer for minimum 2 years Make : Wipro cat part No. LL20-111-XXX-65NE3 or equivalent of Philips/ Bajaj

Sub main wiring with PVC insulated unsheathed FRLS cable 1100 volts grade multi stranded copper conductor cable 2 runs of 4 sqmm drawn through in and incl suitable size PVC casing capping and all accessories fixed to wall/floors along with one run 4 sqmm PVC insulated unsheathed copper conductor multi stranded cable 1100V grade as earth continuity conductor and connected to common earth dolly including taking down existing sub main wiring of any size. Note: (a) 2 runs of 4 sqmm cable along with one run of 4 sqmm cable for earth conductor and PVC casing capping shall be measured as one length. (b) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. Make:- Havells/ Polycab/ Plaza.

Surface & wall mounted LED battern with 5 watt LED fitting complete with all accessories internally, pre-wired, connecting up with twin core twisted flexiable copper conductor cable of suitable size in replacement all as directed by Engineer-in-Charge. Make : Bajaj cat part No 112405BCLSB 05WH or equivalent of philips / Havells

IP 66 LED bulkhead luminaire, consuming a power of 9W. Lumen output not less than 1080 lumens with a system efficacy > 115 lm/W, translucent UV stabilised poly carbonate anti-glare diffuser, colour temp not less than 6500K, PF > 0.95 shall have 50,000 burning hours as per L70 criteria, with surge protection device minimum 2KV, LED driver with constant output voltage and current at input voltage of 110 Volt to 270 Volt AC at 50 Hz,. The bulkhead body base should have inbuilt provision for easy mounting on wall/ ceiling with PVC insulated copper conductor 3 core cable of 0.5 sqmm. The body of luminaire should be dust, water and all weather proof for out side mounting and should be manufactured with flame retardant UL 94VO, UV resistant, glow wire test 960° impact IK 10, Halogen free, ROHS compliant, conforming to IEC 60529, Including taken down existing one complete all as specified and as directed by Engineer-in-Charge. The luminaire shall be BIS certified. Make :- Philips/ Bajaj Notes:- 1. The Contractor shall submit test report from manufacturer of LED fittings giving detail of each parameter /specifications of led luminaire mentioned in the BOQ item. 2. The contractor shall submit to Engr-in-Charge LM-80 and LM-79 report from the NABL approved lab of LED chip used and luminaire respectively. 3. The contractor shall submit warranty certificate from manufacturer for minimum 2 years.

LED retrofit lamp 7W, warm white, (lumen output not less than 1350 lumens) with B-22 holder base with thermal conductive engineering plastic white colour housing and aluminium heat sink with specially designed fins clear /cool white, power factor more than 0.9, with surge protection device minimum 2KV, color temperature not less than 6000K, CRI more than 80, LED driver with constant output voltage and current at input voltage of 140 Volt to 285 Volt AC at 50 Hz, glarefree, 0 UV radiation Including taken down existing one complete all as specified and as directed by Engineer-in-Charge. Notes:- 1. The contractor shall submit to Engr-in-Charge LM-80 and LM-79 report from the NABL approved lab of LED chip used and luminaire respectively. 2. The contractor shall submit warranty certificate from manufacturer for minimum 2 years Make : Wipro cat part No. LL20-111-XXX-65NE3 or equivalent of Philips/ Bajaj

LED retrofit lamp 5W, warm white, (lumen output not less than 1350 lumens) with B-22 holder base with thermal conductive engineering plastic white colour housing and aluminium heat sink with specially designed fins clear /cool white, power factor more than 0.9, with surge protection device minimum 2KV, color temperature not less than 6000K, CRI more than 80, LED driver with constant output voltage and current at input voltage of 140 Volt to 285 Volt AC at 50 Hz, glarefree, 0 UV radiation Including taken down existing one complete all as specified and as directed by Engineer-in-Charge. Notes:- 1. The contractor shall submit to Engr-in-Charge LM-80 and LM-79 report from the NABL approved lab of LED chip used and luminaire respectively. 2. The contractor shall submit warranty certificate from manufacturer for minimum 2 years Make : Wipro cat part No. LL20-111-XXX-65NE3 or equivalent of Philips/ Bajaj

Supply and Fixing in replacement indoor decorative extruded aluminium anodised housing /CRCA sheet steel coated housing (suitably coated to improve resistance against corrosion) LED T8 batten type luminaire (LED batten shall be prewired box type) retrofit solution with and including replaceable retrofit cool day white LED tube rod with well designed aluminium heat sink /aluminium housing for excellent heat dissipation; 4feet (appx) size, high efficiency electronic driver, system wattage 20 watt (lumen output not less than 2000 lumen), power factor more than 0.9, with surge protection device minimum 3KV, colour temperature not less than 5700K, LED driver with constant output voltage and current at input voltage of 140 Volt to 285 Volt AC at 50 Hz, CRI more than 80, glarefree, no UV radiation light fitting with wall mounting arrangement and making connections with PVC insulated copper conductor 3 core cable of 0.5 sqmm complete all as specified and directed. Make : Philips CAt part NO.85395000 /Wipro cat part No. LL13-181-650 for rod and WIO921208 or equivalent in Bajaj

Notes :- (a) The contractor shall submit to Engineer-in-Charge LM-80 and LM-79 report from the NABL approved lab of LED chip used and luminaire respectively while getting sample and material approved. (b) The contractor shall also submit test report from the manufacture to comply with all requirements and specifications given in the contract. (c) The contractor shall submit warranty certificate from manufacturer for minimum 02 year.

LED retrofit lamp 9W, warm white, (lumen output not less than 1350 lumens) with B-22 holder base with thermal conductive engineering plastic white colour housing and aluminium heat sink with specially designed fins clear /cool white, power factor more than 0.9, with surge protection device minimum 2KV, color temperature not less than 6000K, CRI more than 80, LED driver with constant output voltage and current at input voltage of 140 Volt to 285 Volt AC at 50 Hz, glarefree, 0 UV radiation Including taken down existing one complete all as specified and as directed by Engineer-in-Charge. Notes:- 1. The contractor shall submit to Engr-in-Charge LM-80 and LM-79 report from the NABL approved lab of LED chip used and luminaire respectively. 2. The contractor shall submit warranty certificate from manufacturer for minimum 2 years Make : Wipro cat part No. LL20-111-XXX-65NE3 or equivalent of Philips/ Bajaj

Sub main wiring with PVC insulated unsheathed FRLS cable 1100 volts grade multi stranded copper conductor cable 2 runs of 6 sqmm drawn through in and incl suitable size PVC casing capping and all accessories fixed to wall/floors along with one run 6 sqmm PVC insulated unsheathed copper conductor multi stranded cable 1100V grade as earth continuity conductor and connected to common earth dolly including taking down existing sub main wiring of any size. Note: (a) 2 runs of 6 sqmm cable along with one run of 6 sqmm cable for earth conductor and PVC casing capping shall be measured as one length. (b) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. Make:- Havells/ Polycab/ Plaza.

4 feet surface mounted battern type luminaire with a power consumption not more than 16 W, luminaire lumen output of 2000 lumens, luminaire efficacy > 120 lm/W with an operanting voltage range from 140V-270V. The luminaire shall have a white CRCA housing with a poly carbonate diffuser to provide uniform light and sleek design with width not more than. The luminaire shall have a CCT of 6500 K, CRI>80, power factor>0.95, SDCM<5, THD<10% and 50,000 burning hours as per L70B50 criteria. The luminaire shall have flicker content<5% and shall have high and low cut off with auto restart feature. The luminaire shall be EMI/ EMC complaint and shall have a internal surge protection of 4 KV. The luminaire shall have Class-1 Electrical insulation, Class-B serviceability (The driver can be replaced at site level). The luminaire shall not weight more than 7 Kg and the luminaire and driver shall be BIS approved with "R" number mentioned Including taken down existing one complete all as specified and as directed by Engineer-in-Charge. Make : Equivalent to BN308 LED20S 6500 L120 PSU WH of Philips or equivalent in Bajaj or Wipro.

Note :- (a) LED Chip make shall be Nichia, Osram, Cree, Lumilid. (b) The contractor shall submit to Engineer-in-Charge LM-80 and LM-79 report from the NABL approved lab of LED Chip used and luminaise respectively while getting sample and material approved. (c) The contractor shall also submit test report from the manufacture to comply with all requirements and specifications given in the contract. (d) The contractor shall submit warranty certificate from manufacturer for minimum 02 years.

Sreekrupa Enterprises

jk construction

T C KARUNANITHI

Neptune Engineers and Builders

NAVEEN ENTERPRISES

eurekaenterprises

KUMAR AGENCIES

SENTOOR BUILDERSS