work1

Providing and laying of open gym and children jhulle work at housing board near bus stand,Sikar

SURF BOARD Providing, and fixing of Surf Board of size 910mm (Length) x 860mm (Width) x 1400mm.(Height) fabricated with a center pipe of 100mm Nominal Bore shall be made from “c” class G.I. pipe. The sleeve pipe shall be made of 125mm OD seamless pipe with thickness of 5mm and bolted to main frame with M10 SS bolts. The bottom support shall be welded of M.S. plate of Ø 250 mm & 10mm thickness. The handle frame of 25NB shall be made from “c” class G.I. pipe The paddle frame of 50NB shall be made from “c” class G.I. pipe supported with 70X8mm bend M.S. flat and can be replaceable. The foundation to be used for fixing should be a structure and shall be made from center pipe of G.I. of 80NB “c” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Bushes shall be used of 70mm Outer Diameter with 5mm thickness. The footrests shall be made from Aluminum casting material of size 320mm X270mm X5mm. For support to footrest of 200mmX250mm with 3mm thickness M.S. Plate shall be used. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. The pins to be used shall be made up of Ø35 mm SAE 8620 bright material. The bearing shall be used are of “6007zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nut bolts shall be used for assembly. The cerclips shall be used for assembly of A34.The powder coating shall be done with Pure Polyester powder of Ackzonoble or Berger with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc.

CROSS TRAINER Providing and fixing of Cross trainer of size 1320mm (Length) x 600mm (Width) x 1750mm. (Height) fabricated with the main frame Pipes of 80NB shall be made of “C” Class G.I and pipe with single bend pipe with 250mm radius. The bottom support of M.S. round plate of Ø250 mm & 10mm thick. The Handle Frame shall be made up of 25NB “C” Class G.I. Pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. pipe of 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe should be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm and CRC square pipes of 3mm thickness. To build structure bushes to be used which shall be made from M.S.seamless pipe of 60mm OD with 5 mm thickness. The footrests shall be made from Aluminum casting material of size 130 mm X 310mmX5mm thickness and mounted on M.S. Plate of Size 130mmx310mmx3mm thick. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 35mm, 25mm, and 17mm shall be made up from SAE 8620 bright . The Bearings shall be used of “6007zz” “6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 Micron thickness. A16 , A 24 mm circlips shall be used for assembly. Bolt M8X16 mm and NY lock nut of M8 shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc

THI-CHI SPINNER (2 WHEEL) Providing and fixing of Thi-Chi spinner (2 Wheel) of size 700mm (Length) x 1000mm (Width) x 1280mm (Height) fabricated with a center pipe of 100NB shall be made up of “C” Class G.I. pipe. The handle movement round frame shall be made up from 25 NB “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class, welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. The pins to be used shall be made up of Ø 25 mm of SAE8620 bright material. The bearing shall be used of “6201zz” & “6205zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile S.S. nut bolts shall be used for assembly. Foundation cover Closing Cap shall be made from FRP Material with 0.7 mm thickness. The cerclips used for assembly shall be of of A24 and A11. The nylon bush shall be used for handle knob. The powder coating shall be done with pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness. Bolt M8X16 mm and Nylock nut of M8 shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc

SEATED PULLER Providing and fixing of Seated Puller of size 1900mm (Length) x 740mm (Width) x 1920mm. (Height) fabricated with a center pipe is of 100NB shall be made from “C” Class G.I. pipe. Bottom support of M.S. round plate of Ø 250 mm & 10mm thickness shall be welded. All linkages shall be made up of 25NB “C” class G.I. pipe. The handle frame of 32NB “C” class G.I. pipe. The seat frame of 32NB “C” class G.I. pipe, To build structure bushes to be used which shall be made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush shall be used. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Foundation cover Closing Cap shall be made from FRP Material. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 25mm and 17mm shall be made up from SAE 8620 bright material. The bearings shall be used of “ 6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts shall be used for assembly. The cerclips to be used for assembly are of A16 The powder coating shall be done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc

SIT UP BOARD DOUBLE Providing and fixing of Sit up Board double of size 1760mm (Length) x 1140mm (Width) x 660mm (Height) fabricated with the main frame of 25mm NB shall be made from “C” Class GI pipe. FRP sheet of 3mm thickness shall be moulded on main frame. The remaining frame of the sit up board of 32mm NB shall be made from “C” class GI pipe. The powder coating shall be done with Pure Polyester powder Ackzonoble or Berger Paints with 60 to 70 micron thickness. The foundation shoud be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc

CHEST PRESS Providing and fixing of Chest Press of size 2000mm (Length) x 710mm (Width) x 2200mm. (Height) fabricated with the center pipe of 100NB shall be made up of “C” Class G.I. pipe. The bottom shall be welded with support of M.S. round plate of Ø250 mm & 10mm thickness. The connecting pipes shall be made up from 25NB “C” class G.I. pipe. The handle frame shall be made up from 32NB “C” class G.I. pipe. To build structure bushes to be used which shall be made from MS seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush shall be used. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. Sheet of size 330mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Foundation cover Closing Cap shall be made from FRP Material with 0.7 thickness. Pins to be used of Diameter 25mm and 17mm shall be made up from SAE 8620 bright material. Bolt M8X16 mm and Nylock nut of M8 shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The bearings shall be used are of “6205zz” & “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts shall be used for assembly. The cerclips to be used for locking shall be made up of A24 mm & A16mm. The powder coating shall be done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc.

DOUBLE TWISTER STANDING Providing and fixing of Double Twister Standing of size 1500mm (Length) x 600mm (Width) x 1300mm. (Height) fabricated with a Center Pipe of 100NBshall be made from “C” Class G.I. material. The bottom shall be welded with support of M.S. round plate of Ø250 mm & 10mm thickness. The bottom frame of 32NB shall be made from “C” class G.I. pipe. The handle frame of 25NB shall be made from “C” class G.I. pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB”C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of size Ø300mm and 10mm thick. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 35 mm shall be made up from SAE 8620 bright material. The bearings shall be used are of “6205zz” permanent lubricated sealed bearing of reputed. Brand. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc

SEATING & STANDING TWISTER Providing and fixing of Seating & Standing Twister of size 1700mm (Length) x 540mm (Width) x 1250mm. (Height) fabricated with a Center Pipe of 100mm NB shall be made from “C” Class G.I. Round Pipe. The M.S. round plate of Ø250 mm & 10mm thickness shall be welded at bottom. Handle and Bottom sleeve pipe of 125mm OD with thickness 5mm should be provided for easy assembly, replacement and maintenance. The bottom frame of the Seating & Standing twister of 32 NB, 50 NB, and 25 NBshall be made from “C” class G.I. pipe. The handle frame of Seating & Standing twister of 25 NB & Foot resting frame of seating side shall be made from “C” class G.I. pipe of 25mm NB. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class, Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRCA square pipes of 3mm thickness. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of size 300mm diameter and 10mm thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. The Pins to be used which shall be made up of Ø 35 mm SAE 8620 bright material. The bearings shall be made of of “6205zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done by Pure Polyester powder of Berger Paint with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc

PUSH UP BARS Providing and fixing of Push Up Bars of size 1220mm (Length) x 550mm (Width) x 1700mm. (Height) fabricated with the main frame of 100 NB shall be made from “C” Class G.I. pipe. The M.S. round plate of Ø250 mm & 10mm thickness shall be welded at bottom.The handle frame of 25 NB shall be made from “C” Class G.I. pipe.The foundation shoud be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipeshall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness.Closing Caps shall be made up of high quality Fiber reinforced Plastic material.Foundation cover Closing Cap shall be made from FRP Material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coatingshall be done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc.

Supply and fixing different type of steel pre-fabricated garden bench/ jhula/ slides and other children play items made of steel duly painted as per approved design and specifications by engineer in-charge made of MS pipe, Flats, rectangular hollow section or other steel sections duly welded and or nut bolted where ever required, rubbing and buffing welded joints to make safe for use of children and painted in approved pattern complete as required.

Please Enable Macros to View BoQ information