Provn of toilet cum urinal points near open AIR Auditorium and wellness Park at Mil Stn Sangrur under GE(S) Patiala

Amount

M&L for point wiring with FRLS PVC insulated unsheathed multi-stranded copper conductor 1.5 Sq.mm (nominal area ) single core cable 1100 Volt grade drawn in and including rigid non metallic concealed PVC Conduit of suitable size (not less than 20 mm) on wall , surface of ceiling with all fittings, such as tee, bend, elbow, socket etc including pressed steel sunken boxes (Terminal boxes) with earth dolly,duly galvanised, with white shade frame & cover plate of suitable module for modular switch / or sockets including FRLS PVC insulated unsheathed stranded copper conductor 1.5 Sq.mm (nominal area ) single core cable as earth continuity conducter to common earth and connected to earth dolly, complete all as specified and as directed by Engineer-in-charge, for the following :- (a) One light/fan point controlled by one 1-way switch

S&F Switch piano, flush type single pole, one way 6 Amp, 240 Volts, complete all as specified and as directed by Engineer-in-charge.

S&F ceiling rose surface bakelite two to three terminal 65 x 50 mm, complete all as specified and as directed by Engineer-in-charge

S&F MCB DB SPN 4 Way with acrylic double door complete all as specified and as directed by Engineer-in-charge

S&F MCB SPN 240V 40 Amps C series 10 KA complete all as specified and as directed by Engineer-in-charge

S&F MCB SP 240V 6 to 32 Amps C series 10 KA complete all as specified and as directed by Engineer-in-charge

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2 mtr deep below ground level with top edgw of the plate not less than 1.4 mtr below normal ground level , connected earth wire 4 sqmm by means of bolts nuts check nuts and washers of galvanised iron or steel all as shown in electrical plate No 5 connected to earthing test point all as specified or indicated including PCC pit in PCC(1:3:6) type C-1 cast iron frame 50mm thick pre cast RCC(1: 11/2:3) nominal mix cover slab reinforced with 8 mm dia mild steel deformed bar 15cc and suitable handle of 10 mm Dia round bar including necesary excavation earth work in soft/loose soil and disposal of spoil to a distance n.exc 50m and funnel with watering pipe wire mesh copper lugs etc GI protection pipe of size 15 mm bore including testing complete all as specified and as directed by Engineer-in-charge

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver, complete all as specified and as directed by Engineer-in-charge

S&F in replacement Tube light fittings LED type 1x20 Watt 4 ft long incl LED tube rod and incl 3 core flexible wire 0.75 Sqmm copper cable complete all as specified and as directed by Engineer-in-charge

Supply & fix LED bulk head ,10 W complete all as specified & directed.

S&F in replacement Tube light fittings LED type 1X10 Watt, 2 ft long incl LED tube rod and incl 3 core flexible wire 0.75 Sqmm copper cable complete all as specified and as directed by Engineer-in-charge

S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by Engineer-in-charge.

S&F LED Bulb 7 watt 230 volt retrofit type complete all as specified and as directed by Engineer-in-charge.

Supply and laying 10 sqmm 2 core cable XLPE/PVC insulated armoured and sheathed LT 1100 volts grade with aluminium conductor complete all as specified and as directed by Engineer-in-charge.

Excavation in trenches in soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth and getting out complete all as specified and as directed by Engineer-in-charge

Returning filling in including spreading leveling, watering and well ramming in layers, complete all as specified and as directed by Engineer-in-charge

Removing excavated soil to a distance not exc. 50 mtr and depositing complete all as specified and as directed by Engineer-in-charge

M&L for sand cushioning with dry and clean over and under the cable, 80 mm sand laid before laying and 150 mm laid before laying the cable complete all as specified and as directed by Engineer-in-charge.

Supply and laying best quality bricks locally availanle sub class ‘B’ bricks (old size) for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable complete all as specified and as directed by Engineer-in-charge.

Excavation in trenches not exceeding 1.50 metre wide & not exceeding 1.5 metre deep and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-charge.

M&L for brick work in cement mortar (1:6) using sub class 'B' bricks staight or curved on plan exc 6.0 m mean radius complete all as specified and as directed by Engineer-in-charge.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone)as in fdn filling mass concrete complete all as specified and as directed by Engineer-in-charge.

M&L 40mm thick PCC 1:2:4 B0 (12.5mm graded crushed stone aggregate ) as in Damp proof course to horizontal or vertical surfaces including necessary form work complete all as specified and as directed by Engineer-in-charge.

M&L for RCC (nominal mix) type B1 (1:1.5:3 ) 20mm gradede stone aggreagate as in beams,contilever, bressummers, lintel over1.5mtr span complete all as specified and as directed by Engineer-in-charge.

M&L for RCC (nominal mix) type B1 (1:1.5:3 ) 20mm gradede stone aggreagate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engineer-in-charge.

Form work to soffits of suspended slabs such as roof slabs, floorslabs, landings and similar work;not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed by Engineer-in-charge.

M&L formwork to sides and soffits of floor or roof beams,beam haunchings, girders, bressumers, lintels, cantilever, shelves including supports, overhangs, etc also splys between floors and beams etc complete all as specified and as directed by Engineer-in-charge.

M&L for deformed steel bars 10 mm dia and over, cut tro length, bent to shape required, including cranking, bending spirally or hooping for coloum hooking end stand binding with miuld steel wire less than 0.9 mm dia complete all as specified and dierected.

All as per serial item no 28 but 5 mm dia and over upto and including 10 mm dia Tor ars as instirrups, spacers and binders, conferming to geraded IS -432 (Part-I) complete all as specified and as directed by Engineer-in-charge.

Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed by Engineer-in-charge.

M&L for hard core of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick broken stone, water and ramed to atrue surfaces complete all as specified and as directed by Engineer-in-charge.

M&L for 100 mm thick PCC 1:4:8 , D2 (40mm graded crushed stone aggregate ) as in sub-base coarse complete all as specified and as directed by Engineer-in-charge

75 mm thick PCC (1:3:6) type C1 (using 20mm grade aggregate) as in plinth protection/pathway finishing the surfaces even & smooth w/o using extra cement complete all as specified and as directed by Engineer-in-charge

Glazed ceramic tiles 300 x 600mm x 7mm thick with highlighted coloured on vertical surfaces set and jointed in neat cement slurry and pointed in white cement to match including 10mm thick rendering of CM 1:3 complete all as specified and as directed by Engineer-in-charge. (Make: Kajaria, Bell, Johnson)

Non skid ceramic jointless (coloured files) of size 400 x 400 x7mm thick in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed 15 mm thick in cement mortar (1:4) complete all as specified and as directed by Engineer-in-charge. (Make: Kajaria, Bell, Johnson)

S&F factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5 X 38.10 X 1.29 mm including 5mm thick frosted glass in lower 55% portion of shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in upper 45% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and complete all as specified and as directed by Engineer-in-charge

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. M S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joining together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed by Engineer-in-charge. (Make: M/S Rajshri)

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification and drawings including all fixtures shown on drawings complete all as specified and as directed by Engineer-in-charge. (Make:Rajshri or Equivalent)

100 mm size PVC butt hinges complete all as specified and as directed by Engineer-in-charge

150MM PVC handles complete all as specified and as directed by Engineer-in-charge

200mm long PVC tower bolt complete all as specified and as directed by Engineer-in-charge

Rendering 15 mm thick in cement mortar 1:4 , mixed with water proofing compound, on brick or concrete surfaces, trowelled to even and smooth finish without using extra cement with WPC paid and measered sepretly complete all as specified and as directed by Engineer-in-charge.

All as per srl item No 42 hereinbefore but 10mm thick in CM 1:6 finishing even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

Rendering 5 mm thick in cement mortar 1:3 as on concrete surfaces in ceiling finished even and smooth without using extra complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of white wash complete all as specified and as directed by Engineer-in-charge.

Rotational moulded polythene three layer water storage tank cylindrical vertical with closed top 500ltr capacity hoisted and fixed in position, connecting to inlet or outlet and washout including disconnecting and demolition of existing tanks of any description complete all as specified and as directed by Engineer-in-charge. (Make: sintex, Aqua polymer, Lotous)

S&F in repair 15 mm dia Bib Tap cast copper alloy fancy type CP with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engineer-in-charge.

Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe of 20mm having minimum weight 210gm/each fixed valve complete all as specified and as directed by Engineer-in-charge. (Make : Prayag)

Vitreous china squatting pan white colour of Orissa patten size 580 x 440 white with (C I P trap long size) joint run and lead front or back inlet with integral footrest including connection to trap and to flushing pipe,anti-syphonage pipe, etc, fixed in repair complete and making good to floor in CM 1:3 complete all as specified and as directed by Engineer-in-charge. (Make : Hindware, Cera, parryware)

S&F in repairs low level dual flushing cistern of PVC 10 ltr capacity incl 45cm long PVC connection with brass nut at both ends, PVC flush pipe 32 mm bore and mild steel brackets of angle iron 25 x 25 x 3 mm, oval all length 20 cm with red-oxide primer complete all as specified (ISI Marked) incl taking down HL/LL flushing cistern and making good the disturbed surfaces in CM 1:3 complete all as specified and as directed by Engineer-in-charge. (Make : Hindustan sanitry, Parryware, orient sanitry)

S&F vitreous china wash basin, size 550 x 400mm white including brackets, and waste coupling & pipe of 32mm dia etc with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed complete all as specified and as directed by Engineer-in-charge.

S&F 15mm dia pillar tap cast copper alloy chromium plated fancy type (ISI Marked) complete all as specified and as directed by Engineer-in-charge.

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm dia complete all as specified and as directed by Engineer-in-charge.

S&F brass chromium plated angle cock 15mm bore with crutch or butterfly handle screwed to iron pipe, fixed in repair complete all as specified and as directed by Engineer-in-charge.

Steel water tubing 15mm bore, medium grade, galvanised, with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified and as directed by Engineer-in-charge. (Make : Tata, jindal, surya prakash )

Steel water tubing 20 mm bore, medium grade, galvanised, with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified and as directed by Engineer-in-charge. (Make: Tata, jindal, Suryaprakash)

S&F CP towel rail 600mm long with brackets, chromium plated 20mm dia in repair complete all as specified and as directed by Engineer-in-charge.

S&F in repairs CP Soap dish of size approximate size 160x90mm, fixed to plugs with chromium plated brass screws complete all as specified and as directed by Engineer-in-charge

Supply & fix 110mm dia PVC (SWR) pipes single/double socketed in any length with rubber ring joints, fixed to walls complete all as specified and as directed by Engineer-in-charge

All as per serial item No 61 here-in-before above but bore of pipe 75 mm dia fixed to walls/floor complete all as specified and as directed by Engineer-in-charge

S&F(SWR) 110mm bore pipe junction single (single T) equal and unequal with access door complete all as specified and as directed by Engineer-in-charge

S&F PVC (SWR) bends 110mm bore of any radius with access door complete all as specified and as directed by Engineer-in-charge.

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm dia complete all as specified and as directed by Engineer-in-charge.

Supply only WPC complete all as specified and as directed by Engineer-in-charge. (Make : Pidilite, Sikka, Forsroc)

M&L for brick work in cement mortar (1:4) using sub class 'B' bricks staight or curved on plan exc in half brick thick wall complete all as specified and as directed by Engineer-in-charge.

S&F vitrious china urinal, half stall type, white including flushing cistern, flush pipe and waste pipe. CP waste coupling complete all as specified and as directed by Engineer-in-charge

S&F 15mm bore self-closing taps, cast copper alloy chro-mium plated screwed for iron pipe and fixed complete all as specified and as directed by Engineer-in-charge

NARINDER KUMAR SONS