Construction of Kaariyamandappam near CMC Colony, Sathuvachari in Ward No. 18, Zone-II at Vellore Corporation

Earth work excavation in sand silit (or) other loose soil, wet sand sandy loam including excavated earth with initial lead and lift of 1m and 2m respectively etc., complete as per standard specification.

(a) Narrow Foundations - First Depth - Up to 2.00m Depth

(b) Open Earth Work Excavation

Supplying and filling in foundation and basement with Crushed Stone Sand (M- Sand) in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Cement Concrete 1:4:8 (One Cement, Four sand and eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification

Brick work using Country Bricks of size 8-3/4" x 4-1/4" X2-3/4"" in Cement Mortar 1:5 (One cement and five crushed stone sand) including curing neat finishing, etc., complete complying with standard specifiction.

(a) Up to Basement

(b) Ground floor

Supplying and fabricating in position of MS or RTS rods for RCC work including the cost of steel and binding wire and all labour charges for cutting bending tying grill and stengthening and all labour chrges including the fabeication charges etc complete.

Supplying and erecing steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as colunn footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal struttig using mild steel sheets of size 90cm X 60cm and 10 BG stiffened with welded mild steel angles of size 25mm X 25mm X 3mm for boarding, laid over silver oak joists of size 10cm X 6.5cm spacced at about 75cm centre to centre orat suitable intervals etc., complete in all flors complying with standard specification - Plinth Beam

Centering for Soffits of RCC slabs of plane surface like lintel, beams, etc., including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S. angles of size 25m X 25mm X 3mm laid over silver Oak (C.W.) joists of size 10cm X 6.5cm (spacced at about 90cm c/c) and supported by casurina props of 10cm to 13cm dia (spaced of 75cm c/c) complying with standard specification and directed - For Plane Surfaces such as rectangular or Square RCC Columns, sunshades, top and bottom slab of RCC Boxing etc.

Supplying and erecing steel centering for sides and soffits including necesary supports and strutting upto 3.29M height for plane surfces as detailed below in all floors with all cross bracings using Mild Steel sheetsof size 90 X 60 cm and 10BG stiffened with welded mild steel angles of size 25mm X 25mm X 3mm for boarding, laid over silver oak joists of size 10cm X 6.5cm spacced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at not morethan 75cm centre to centre etc., completec omplying with the standard specificaion - For Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams etc.,

Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS standards. (No separate payment will be made by the Department for the excess usage of materials)

(a) Up to Basement

(b) Ground Floor

Plastering with cement mortar 1:5 (one cement and five sand) 12mm thick, in all floors etc., complete complying with standard specification,

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers.

White washing two coats with freshly burnt shell lime white in colour in all floors including cost of lime and other materials brushes scaffolding charges etc.complete complying with standard specification and as directed.

Supplying and painting the walls with two coats of cement paint over one coat of cement primer as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use of work).

Supply and Delivery Fabrication of MS doors and windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

(a) Fully panelled Double leaf - Door size 1.00 X 2.10

(b) Fully panelled Double leaf - Window (without Ventilator)

( c)Ventilator size 0.45 X 0.60

Solid PVC Door Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter.

Solid panel PVC door with frame

Paving the floor with kota stone slab of size 600 x 600 of 18 / 20mm (un-polished) in all floors laid in of cement mortor 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and pointed with colour cement neatly including polishing with polishing stone and oxalic acid etc., so as to perfectly smooth and glossy and including hire charges for polishing machine and power consumption charges etc. The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Weathering Course with Concrete Broken Brick Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab,the proportion of brick jelly to lime being 32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete.

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Paving the floor with design Antiskid ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand) 20mm thick laid in-situ and pointed with same coloured cement

Dadooing walls with Glazed tiles of sizes 305mm X 200mm X 6mm size of approved make and quality and colour Set in cement mortar 1:2 (One part of Cement and two part of Plastering Sand (P- Sand)) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Supplying and filling the basement with Good Earth filling in layers of not more than 15cm thick well rammed watered and compacted - etc., complete complying with standard specification.

Supply and delivery and fixing of HDPE tank as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,

(a)1000 Litre

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 liters capacity PVC / 12.5 liters capacity porcelain low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting

Supply, Delivery and laying of the UPVC Pipes including UPVC specials etc, complete as directed by the departmental Engineers

(a) 160mm PVC Pipe 4 kg. per cm2 (WITH ISI MONOGRAM)

(b) 160mm PVC TEE

( c)160mm PVC Elbow

(d) 160mm PVC Bend

(e) 32mm UPVC Pipe

(f) 32mm UPVC TEE

(g) 32mm UPVC Elbow

(h) 32mm UPVC Bend

(i) 32mm UPVC Union

(j) 32mm UPVC Coupling

(k) 75mm PVC Pipe 4 kg. per cm2 (WITH ISI MONOGRAM)

(l) 100mm x 75mm PVC Nahini / Floor Trap with PVC Grating

(m) PVC Screw Down Tap Heavy Type 20mm dia

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V on 7 / 20 GI bearer wire for service connection mains including cost of all material charges and labour charges etc, complete as per standard specification

Supply and run of 2 of 4sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in 25mm dia GIpipe (Class 'B') suitably bent at both ends with necessary angle iron upright and end supports for mains

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuseunit (500V) 32A neutral link and earth link (1"x1/8" copper flat) on TWplank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TWplank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1No 40Amp 30MA Double Pole RCD / RCCB (Lower End) with suitable necessary connection

Earthing as per PWD standard with an earth electrode of 2metre Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work

Wiring with 2 x 1.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch with painting of suitable colour for open PVC light point / fan point (for electronic regulator) (6 points per coil) Wiring with 2 x 1.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor cable of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box inflush with wall with 5A FT switch covered with hylum sheet of 3mm thick with painting of suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for open PVC light point / fan point (for electronic regulator)

Supply and fixing of single box type 4'40W fluorescent fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed FRLS copper leads from terminals to the fitting

Supply and fixing of 1200mm sweep AC ceiling fan complete with stepped electronic 300W regulator with the existing down rod on the existing clamps

Supply, Deliver and fixing of LED Out Door Fittings (Light Emitting Diode) Higher End including cost of material, labour charges and all other incidental charges etc., complete.

(a) 30W LED Street Light Fitting with LED

Supply and fixing of ceiling fixture 250 / 300mm complete with gallery etc clear glass Opac / Crystal suitable for 7 W / 9 W LED bulb with bulb

Please Enable Macros to View BoQ information