S&T work for Provision of LHS in lieu of LC No. 357 (BAV-MMS), JD-1 (DATR-TMKA), CT 29 (RJGR Yard), CT 65 (HND-MRDL), JB-12 (GHNH-NQR), CT 42 (DNKL-SSPR), CP 8 (MTND-KDRP), and LHS at Trespassing Locations between KPJG-JRPD, KDRP- RCTC, Jakhapura-Jenapur, under Khurda Road Division.

A1-EXECUTION OF SIGNALLING WORKS: RATES ARE INCLUSIVE

A2-EXECUTION OF SIGNALLING WORKS: RATES ARE INCLUSIVE

B1-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE

B2-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE

B3-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE

C -SUPPLY & EXECUTION OF DRAWING WORK : RATES ARE

4.Transportation of released materials from one site to another site or store of concerned SSES/(In-

charge) or as advised by Sr.DSTE/KUR.

Item- 1 EXECUTION OF SIGNALLING WORKS

S No. Item Description of Item Unit Qty Rate Amount

KHURDA ROAD DIVISION-S AND T/ECOR

1 1 Installation/Alteration/Phase working, Wiring, Station 3.00 1314621.00 3943863.00

testing and commissioning of complete

Electronic Interlocking System

(Distributed/Centerlized Configuration

System with Hot Stand by feature) supplied

as per Item Nos. 01 of Schedule-B-I including

transportation from Consignee's depot to site

of work. This includes execution of labour

portion, Interface relay wiring, erection of

relay racks, fixing of relays and associated

work in relay room, proper fixing of Operator

VDU Terminals etc (The Relays for interface

relays wiring will be supplied by Railways.

The Contractor shall supply all other

materials required for installation, wiring,

testing and commissioning). NOTE:- 1)

Installation & commissioning of Electronic

Interlocking is as per Section-H , Chapter-08.

2) If it is phase working, other than initial

phase design, supply of application logic

required for phase working should be done

by the Contractor agianst this item. 3) The

work includes manufacture/ fabrication,

supply and installation of SM's console and

side table extension as per site requirement

and as advised by site Engineer to

accomodate VDUs, other S&T equipments

and SM's stationary for operation of VDUs

and execution of day to day work for

operation of trains.

2 2 Factory acceptance test (FAT) with ECoR Station 3.00 700837.00 2102511.00

officials, Only for Subsequent Phase working

not for Initial working.

3 3 Site Acceptance Testing(SAT) with ECoR Station 3.00 723923.00 2171769.00

officials, Only for Subsequent Phase working

not for Initial working.

Schedule A2-EXECUTION OF SIGNALLING WORKS: RATES ARE INCLUSIVE OF:1.All taxes., 2.Supply of

sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of materials to site.,

4.Transportation of released materials from one site to another site or store of concerned SSES/(In-

charge) or as advised by Sr.DSTE/KUR. (Item Directory - Not Applicable)

Item- 2 EXECUTION OF SIGNALLING WORKS

S No. Item Description of Item Unit Qty Rate Amount

1 1 Alteration of existing panel,wiring and testing Station 5.00 42357.40 211787.00

and commissioning of Control

Panel[Operation-cum-Indication Console] as

per Specn. No.S/36/87 amendment-2,

complete with termination of cable, painting

and lettering as required. Railway will supply

Control Panel and multi core indoor cables

only. Tender shall supply Dominoes, buttons,

keys, counters, MS Angle/Flat, Hylum sheet,

MS clamps, Bolts and nuts, PVC pipes,

Screws, Sleeves, PVC cables, PVC pipes, PBT

terminals, Fuses, LEDs etc and all other

materials required for the work at his own

2 2 Alteration of wiring in existing Relay rack/ CT Numbers 11.00 28281.00 311091.00

rack/composite relay rack. This includes

supply of all types of wires, eyelets, nuts &

bolts, bunching material, ferrules, ARA

terminals, fuses & fuse blockes by the

contractor at his own cost. Lettering &

painting to be done by the contractor at his

own cost. Wire (RDSO Approved Sources) to

be inspected by the representative of

Railway before use.

KHURDA ROAD DIVISION-S AND T/ECOR

3 3 Wiring, testing and commissioning of overall Station 7.00 140176.00 981232.00

circuits and ground gears of approved

interlocking arrangement as per approved

circuit diagram and Interlocking plan. This

also includes making corrections/alterations

in As Planned drawings and documents as

per the execution at site. This includes Free

home signal connection at site and SM's

office, telephone connection in the

tents/goomties and any other communication

arrangement for the Non interlocking at the

station or as decided by the representative of

Railway during non interlocking. The

materials required for preparation of Free

Home indication board will be supplied by the

tenderer.This also includes painting and

l e t t e r i n g of gears. Telephone , VHF

Sets/Walkie Talkie sets will be supplied by

railway. Note: In case of IBS : It includes

overall testing and commissioning of IBS and

both the end stations associated with IBS

4 4 Miscellaneous arrangement for NI period Station 6.00 149624.00 897744.00

comprising of Provision of water-proof

temporary goomty/tent at both side of the

station yard and at central panel building.

Each goomties to be furnished with one iron

table, six chairs, emergency light and

mosquito repellantcaps for NI staff, PA

system, crowbar men for operating point and

men for supplying water to tents.

5 5 Dismantling of existing LC gates and related Numbers 7.00 10461.00 73227.00

gears.This includes

dismantling,stacking,accountal of all the

materials including transportation of all the

released materials to the Railway store.

6 6 Transportation, excavation of pit, casting of Numbers 52.00 19438.00 1010776.00

foundation, plastering and erection of Steel

Apparatus case (full size) with fixing of E-

Type lock, wiring, cable entry, termination

clamping, filling cable pit with sand, painting

and lettering etc., as per Drg.No.

S&T/CON/SK/16. This includes earth work

and/or masonry work required for securing

the apparatus case as per site condition.

Railway will supply apparatus case with 'E'

type lock only from Railway stores at.

Tenderer will supply all wiring materials, PBT

Terminals, fuses, fuse blocks, bus bars, hylum

sheet ISI mark [6mm thickness], wood plank

board of good quality [minimum 3/4" thick,

Cement and transport all the materials to site

of work at his own cost. The wiring materials

such as wire coils, PBT terminals, fuses, fuse

block, etc. should be used from RDSO

approved sources.

7 7 Alteration of wiring in existing apparatus Numbers 36.00 3583.00 128988.00

cases full/half. This includes supply of all

materials in connection with alteration in

wiring. All the materials shall be supplied by

the contractor at his own cost. This includes

entry of cables, sand filling and masonry

work involved. Lettering and painting to be

done by the contractor at his own cost.

Railway shall supply only relays and relay

KHURDA ROAD DIVISION-S AND T/ECOR

8 8 Transportation of signal posts for multiple Numbers 9.00 20931.00 188379.00

aspect colour light signals, complete with

signal units, bases, ladders and other fittings,

excavation of pit, casting of cement concrete

foundation, plastering as per Drg.No

Con/SK/T/12, erection and fixing of complete

fittings of the 2/3/4 aspect signal/signal posts

including termination of cables, wiring, LED

fixing, signal testing and focusing. Name

plate & marker and all other materials shall

be provided by the contractor at his own

cost. Required cement shall be supplied by

the contractor. Arrangement of Screening to

be provided by the contractor if required as

instructed by site Engineer. Contractor shall

prepare jointly with Railway Engineer at site

and submit Signal Sighting report and Signal

test report as per approved format of

Railway. NOTE: (i) 50 % Payment shall be

released after erection of signal post.

Balance 50 % shall be released after

termination of cable, wiring, painting, testing

& focusing of signal. (ii) If foundation is

available at site 30% of the cost is to be

9 9 Laying of Signalling/4 Quad/ 6 Quad/ Power Kilometre 130.00 24389.00 3170570.00

Cable/Telecom cables/ Jelly filled cables of all

sizes in excavated trench, through

GI/RCC/DWC pipes etc. wherever required.

This includes transportation of cables from

the stores to work site and transportation of

empty cable drums with left over cables from

site to the stores at . The length of cable laid

includes the length of cable coil for

termination purpose. NOTE: The cables are to

be carefully handled during loading, un-

loading and transportation to work site. Any

damage found in the cable after final testing,

in view of mishandling of cables, shall be

made good by the Tenderer. Cable should be

maggered before and after laying and

recorded in a register and submitted to the

10 10 Excavation of trenches of following depth and Kilometre 10.60 88821.00 941502.60

width 0.3 Meter detailed below including

clearing of roots and trees etc. for all types of

s o i l . This work also includes covering of

c a b l e s l a i d in trench and backfilling,

ramming, consolidation o f s o i l as well as

disposal of extra soil after cable is laid as

specified in Guidelines on Signalling Cable

laying given by RDSO and any latest circular

i s s u e d by CSTE/ECoR/BBS.Note: Before

refilling of the trenches, the cable laid are to

be tested and recorded for its insulation

value and after satisfaction of site Engineer

the refilling process should start and after

monsoon the route is to be attended for

backfilling the rain cuts, wash out of soils

where ever found. [ii] 1.0 Meter

KHURDA ROAD DIVISION-S AND T/ECOR

11 11 Excavation of trenches of following depth and Kilometre 3.00 71060.00 213180.00

width 0.3 Meter detailed below including

clearing of roots and trees etc. for all types of

s o i l . This work also includes covering of

c a b l e s l a i d in trench and backfilling,

ramming, consolidation o f s o i l as well as

disposal of extra soil after cable is laid as

specified in Guidelines on Signalling Cable

laying given by RDSO and any latest circular

i s s u e d by CSTE/ECoR/BBS.Note: Before

refilling of the trenches, the cable laid are to

be tested and recorded for its insulation

value and after satisfaction of site Engineer

the refilling process should start and after

monsoon the route is to be attended for

backfilling the rain cuts, wash out of soils

where ever found. [iii] 0.8 Meter

12 12 Excavation of trenches of following depth and Kilometre 1.00 106669.00 106669.00

width 0.3 Meter detailed below including

clearing of roots and trees etc. for all types of

s o i l . This work also includes covering of

c a b l e s l a i d in trench and backfilling,

ramming, consolidation o f s o i l as well as

disposal of extra soil after cable is laid as

specified in Guidelines on Signalling Cable

laying given by RDSO and any latest circular

i s s u e d by CSTE/ECoR/BBS.Note: Before

refilling of the trenches, the cable laid are to

be tested and recorded for its insulation

value and after satisfaction of site Engineer

the refilling process should start and after

monsoon the route is to be attended for

backfilling the rain cuts, wash out of soils

where ever found. [i] 1.2 Meter

13 13 Fixing of cable route marker as per drawing Numbers 227.00 706.00 160262.00

in" section-H" at a distance of 100 mtrs.

Along the trench and at places where the

cable route has taken diversion as per

instruction of site Engineer, this includes

casting of foundation at site and fixing of the

marker in the foundation made earlier at site

as per railway directives and specifications,

this includes proper curing of the structure,

All materials required for this like cement,

sand 15 mm chips and steel rod of ISI marks

should be supplied by the tenderer.

14 14 Horizontal direction drilling/boring without Metre 2100.00 1515.72 3183012.00

damage of surface of road/track formation.

The bore shall be 150 mm dia. and shall be

at the proper depth as per site conditions

decided by Enginerin-charge. The ground

level shall be considered ignoring the

bankheight of the bank of the road. The

length of the bore shall be minimum 04 Mtrs

long. This include insertion of different dia.

DWC/GI/HDPE pipes coupling etc as per

direction of Engineer-in-charge. NOTE: The

cost of pipe is not included in this item.

Contractor shall provide all material required

for boring and adequate nos. of labourers for

proper laying of cables in to the bore. Cable

shall be laid cautiously so that it should not

get damage due to rough handling and

pressure on cable.

KHURDA ROAD DIVISION-S AND T/ECOR

15 15 Excavation of trenches in all kinds of soils Metre 510.00 335.00 170850.00

including soft rocky area and clearing of

track etc. to a depth of 1.0 M and width of

0.3 M for track crossing /pucca road/level

crossing gate/platform/station circulating

area or any other place as advised by site

Engineer including transportation and laying

of DWC/RCC/Split RCC/G.I. pipes with or

without coupler. This includes repairing of

track/pucca road/level crossing gate/

platform/station circulating area surface to

original position by ramming and concreting

wherever required soon after the work is

over. DWC/RCC/GI pipes shall be supplied by

the Railway. DWC pipes wherever required

shall be supplied in 6 Mtr. length and shall be

cut to size as per requirement. All other

materials including cement are to be supplied

by the contractor.

16 16 Excavation of trenches including clearing of Metre 790.00 255.00 201450.00

roots of trees etc., in rocky area up to a

depth to be indicated by Railway Engineer at

site as per the site condition [Minimum 0.6

meter] and width 0.3 Mts. at the bottom. This

includes concreting & plastering as per the

instructions of site Engineer and complete

back filling by digging earth from a lead of 30

Mtr. In case 0.8 meter depth or higher is

achieved no concreting is required, otherwise

concreting up to 100 mm thickness should be

done. All materials required for the above

works shall be supplied by the Contractor.

17 17 Cable Duct behind the Relay room and Numbers 12.00 16729.00 200748.00

Goomties of size 1.8 M x1.8 M x 1.2 M to

keep cables entering into it consisting of

brick work of 254 mm thickness of proportion

1:6 with sand filling after coiling of cables.

The top of sand filling covered with

concreting of size 1.30 M x1.30 M and a

depth of 200 mm of proportion 1 : 1.5 : 3

outside of the duct should be plastered with

cement mortar 1 : 6 to achieve smooth

finishing. All materials including cement and

chips of size 40mm. and second class bricks

etc. to be supplied by the contractor.

18 18 Cutting of masonary floor/walls at station Numbers 14.00 6108.00 85512.00

building/ signal goomty/ Gate lodge at a

depth of 0.5 mtr. to 1.0 mtr a t places to be

indicated by site Engineer for entering of

cables inside the building. Only G.I pipes

supplied by Railway and all materials as

clamps, bolts & nuts as instructed by site

Engineer supplied by tenderer. This includes

repairing of masonary floors/walls after the

cables are taken inside. Cement, Sand

required for the work shall be supplied by the

tenderer and also transportation of G.I Pipe

from Store by the tenderer.

KHURDA ROAD DIVISION-S AND T/ECOR

19 19 Trenching and fixing of G.I. pipes of different Metre 260.00 533.00 138580.00

sizes/DWC pipes in hard rocky area up to a

depth of 0.3 M to 0.6 M or at places as per

instructionof site Engineer and concreting [1

: 3 : 6] up to height of 100 mm above the

pipes. G.I. pipes with the socket/ DWC pipes

shall be supplied by the Railway. All other

materials required for the works shall be

supplied by the contractor. Note: [1] In case

of girder bridges, G.I. pipes shall be suitably

clamped by the contractor as advised by the

site Engineer. Clamps shall be supplied by

the contractor. [2] The work including

excavation of trenches in hard rock area up

to a depth of 0.3 M to 0.6 M and back filling,

ramming after completion of work where

ever required. [3] In case of concrete bridges

clearing of ballast for laying of pipes and re

arranging the Railway ballast after

completion of work shall be done by the

20 20 Supply, Transportation and Installation of Numbers 71.00 12306.00 873726.00

earth electrode (make TATA or Jindal as per

Rly. practice) including MS flat for signalling

equipments on lever frame, apparatus cases,

signal, relay racks, cable termination rcak,

block instrument etc. (supply & installation of

earth electrode as per drawing no.

RE/S&T/DRG/Tender/SK/398/94 for apparatus

cases, signal post & other equipments as per

instruction on earthing of S&T equipment.

Laying of earth lead mild steel flat of size

35mmx6mm and fixing of lead MS flat (make

TATA/Jindal or Similar) to earth electrode and

lever frame, signal post & apparatus cases as

per Drg. No. CORE/S&T/ALD/SK/591/2008,

592/2008 and 593/2008 respectively and

instructions on earthing at S&T equipment

and providing cement enclosure for earth

electrode as per drawing no.

RE/S&T/Sig./Tender/SK/13/85 Alt. A) NOTE:

This includes testing of earth value and

indicating the same on the Earth enclosure

by paint. Inspection by RITES.

21 21 Supply, installation, testing and Numbers 13.00 61717.00 802321.00

commissioning of Maintenance free and

permanent earth as per RDSO Specification

No. RDSO/SPN/197 Version 1.0 and Technical

Specification as per section H, Chapter 8.

Inspection by RITES.

22 22 Fixing of relay bases and wiring, bunching, Per Relay 170.00 783.00 133110.00

fixing of relays, wiring in Old relay

racks/location box and also carrying out any

alteration in existing relay rack duly wiring

and connecting New to old and Old to old

relays by standard wires (RDSO Approved

Sources) as per Circuit diagram. Fuses of

bases, condensers, ND fuses, LED indicator &

its wiring for relay rack. All materials required

for this work will be supplied by the

contractor from RDSO Approved Sources.

Relays with accessories will be supplied by

KHURDA ROAD DIVISION-S AND T/ECOR

23 23 Hiring of JCB machine (in good condition) for Hour 125.00 845.61 105701.25

levelling and dressing ground/dismantling

structures including disposal of debris

through dumpers etc. with contractor's

labour, JCB machine, machine operator, fuel

etc. The contractor shall arrange road permit

for vehicle for all the states of operation as

per instruction of engineer-incharge and

vehicle shall not be more than three years

old. payment shall be made for actual

working hours at site.

24 24 Supply, fitting & fixing of ply board 19mm Sqm 400.00 1684.47 673788.00

thick for cupboard, partition wall etc.

Inspection by RITES.

25 25 Transportation of OFC from the store of to Kilometre 5.40 25563.00 138040.20

work site with care, and pushing/ pulling OFC

through the HDPE pipes sealing of the duct

by simple plugs. The cable is to be laid by

mechanised means. At inaccessible places

where mechanised laying is not possible, the

cable is to be laid manually by pulling

through pre inserted rope. Empty cable

drums with or without leftover cable should

be returned to the store. This also includes

testing of cable drums by OTDR in the store

premises before transportation and

submission of results thereof.

26 26 Transportation of HDPE pipe from the store to Kilometre 5.30 15746.00 83453.80

the work site, laying of the same ( with 4mm

nylon rope,pre inserted inside the HDPE pipe)

in excavated trench/already laid GI/RCC

pipe/tubes,jointing, levelling and end sealing

the pipes. HDPE pipe, couplers and end caps

shall be supplied by the railways, Nylon rope

shall be supplied by the contractor.

27 27 Transportation and jointing (straight through Numbers 57.00 1591.00 90687.00

and derivation) of PIJF/quad cables size TSF-

IV as per Specn No. IRS: TC-31/96 & IRS

30/97. Jointing kits shall be supplied by the

Railway. All other materials shall be supplied

by the tenderer.

28 28 Supply, transportation, and installation of Numbers 28.00 11156.00 312368.00

RCC joint chamber with two piece top cover

and bottom cover with hole for drainage and

cable entry as per drawing No.RCIL/ER/DRG-

02/06 (Section-H). This includes trenching for

joint pit, back filling and ramming of pit after

placing the joint closure and cable loop in the

chamber without causing damage to the

same and consolidation of soilas well as

disposal of excess soil. Inspection by

representative of Sr.DSTE/KUR.

29 29 Supply ,transportation & installation of Numbers 26.00 18027.00 468702.00

Optical Fibre cable joint enclosure and

splicing of OFC (24 Fibre) and testing. OFC

spicing shall be done in presence of Railway

Representative. Inspection by representative

of Sr.DSTE/KUR.

KHURDA ROAD DIVISION-S AND T/ECOR

30 30 Transportation, excavation of pit, casting of Numbers 26.00 9742.00 253292.00

foundation, plastering and erection of Steel

Apparatus case (Half size) with fixing of E-

Type lock, wiring, cable entry, termination

clamping, filling cable pit with sand, painting

and lettering etc., as per Drg.No.

S&T/Con/BBS/92/90. This includes earth work

and/or masonry work required for securing

the apparatus case as per site condition.

Railway will supply apparatus case with 'E'

type lock only. Tenderer shall supply all

wiring materials, PBT Terminals, fuses, fuse

blocks, bus bars, hylum sheet ISI mark [6mm

thickness], wood plank board of good quality

[minimum 3/4" thick, cement and any other

materials that are required for the work at his

own cost. Contractor has to transport all the

materials from store at his own cost to the

work site. The wiring materials such as wire

coils, PBT terminals, fuses, fuse block, etc.

should be used from RDSO approved sources.

1) Modification of inside arrangement of

Apparatus cases if required for fixing of

relays/transformers etc. shall be done by the

contractor. Extra shelf, if any, shall be

deposited to the Railway stores by the

contractor. 2) All cables shall be terminated

by providing copper eyelet of suitable size.

Note:-(i) If location box foundation is

available at site 20% of the cost is to be

deducted.(ii) 40% payment shall be released

after erection of location boxes.

31 31 Submission of the final cable route plan after Route 2.70 2111.00 5699.70

the cables are laid and commissioned Kilo

indicating clearly the exact position of the Meter

cable, joints, LB for emergency sockets and (RKM)

other critical materials with reference so

centre line of the nearest track. The final

cable route plan and drawings of the cable

terminations along with all relevant

particulars area to be submitted to the

Railways in original master form as well as 6

32 32 Hiring charges for 7.5 KVA DG Set including Job 12.00 1945.63 23347.56

manpower for operation and maintenance as

per direction of Engineer at site. Only HSD oil

is to be supplied b y Railw a y. Remaining all

other materials including transportation of

the DG set to the site is to be borne by the

contractor. (1 JOB=1 DG set for 1 day)

commissioning & associated wiring for

temporary lighting with 1x28 Watt T5

FL/1X18 W or abo ve indoor type LED T8

fittings with lamp including manpower for

operation and maintenance as per direction

of Engineer at site. All materials including

fitting & wires etc. are to borne by the

contractor. (1 JOB= 1 Light for 1 day).

KHURDA ROAD DIVISION-S AND T/ECOR

34 34 Supply, transportation, erection, and grouting Numbers 10.00 96053.00 960530.00

of Composite Relay Racks / Relay Racks / CT

racks as per Drg.No. SK/DRG/OL/SER/192, SH-

1/2 (for Composite Relay Racks), Drg.No.

SK/DRG/OL/SER/192, SH-2/2 (for Relay Racks)

and Drg.No. S&T/CON/HQ/VSKP/95/92 (for CT

Racks) respectively, including fixing of racks,

PBT terminals 1-Way/6-Way, ND Fuses, Bus

Bars, Eyelets, Hylum strips of required

thickness [12 mm] as per length required at

site, condensers and resistances etc.,

wherever required as per directions of Site

Engineer. Inspection of Composite Racks /

Relay racks/CT racks by Representative of

Railway before use. Tenderer shall supply all

the materials from RDSO approved sources

such as PBT terminals 1-Way/6-Way, ND

Fuses, Fuse blocks, Bus Bars, Eyelets, Hylum

strips (12 mm thicknessn ISI Mark)

condensers and resistances etc., and any

other materials required for the work at his

own cost. Inspection by RITES.

35 35 Wiring and testing of complete Relay Rack / Numbers 10.00 158351.00 1583510.00

CT Rack / Composite Relay Rack as per

wiring diagram for maximum number of plug

in type relay & shelf type relays of different

sizes or as directed by Railway Engineers at

site. This includes rack to rack wiring through

MS ladder fixed on the top of the relay rack,

crimping eyelets in the terminals fitted in the

cables termination rack, numbering by

ferrules 2.5 sq. mm, bunching of wires by

bunching Tape/Thread and buttons, painting

and lettering as required. Wiring of the racks

shall be done with PVC wire of size 16/0.2

mm and 3/0.75 mm. Tenderer shall supply all

wires & wiring materials purchased from

RDSO approved sources. Note: 1) Only relay

and relay bases will be supplied by the

Railway. Contractor has to supply all other

materials for the above work and make

arrangement for transportation of materials

supplied by Railway at his own cost. 2) Only

brass screws shall be used for fixing of relay

bases. 3) All types of wires and wiring

materials, eyelets of sizes (make: Dowell's or

similar), ferrules (2.5 sq.mm), resin core

solder, insulating tape, bunching belt &

buttons etc. are to be supplied by the

contractor. Wires will be procured from RDSO

approved sources only. and all other

components will be supplied by the

contractor as per requirement at site.

36 36 Shifting & adjustment of existing analog axle Numbers 6.00 103670.00 622020.00

counters/SSDAC as per the instruction of the

Railway representative.

KHURDA ROAD DIVISION-S AND T/ECOR

37 37 Transportation and fixing of perforated G.I. Metre 108.00 2653.00 286524.00

Pipes on bridges, culverts, drains or in

trenches or any other place as per instruction

of site Engineer with clamps at 1.5 mts.

interval on steel girder bridges or at places

advised by site Engineer. This includes

supplying of G.I. Pipes, 80/100/150 mm dia.

Specn. No. IS:1239/2004, or latest medium

gauge with threaded collars (Make -TATA

/JINDAL) by tenderer. This also includes 100

mm thick concreting on GI pipes as required

and instructed by site Engineer and all other

materials required for the work shall be

supplied by the tenderer. Note: The G.I. pipe

shall be perforated by drilling 7 mm dia holes

length wise in zig-zag manner staggered at a

distance of 300 mm. G.I. Pipes before and

after perforation and bridge fixtures supplied

by the tenderer will be inspected by

representative of Railway before use. The

bridge fixtures will be supplied by tenderer

for fixing of GI pipes on girder bridges only.

(ii) GI pipes of 100 mm Dia;

38 38 Transportation, installation, testing and Numbers 4.00 27339.00 109356.00

commissioning of Multi section digital axle

counter (MSDAC) in complete system with all

DPs of different track section configuration as

per enclosed drawing. Axle counter device

complete with standard accessories shall be

supplied by the Railway. All sorts of

terminals, sealed wires, condensers,

resistances etc., HDPE pipes and all other

materials required for the above work shall

be supplied by the contractor. This includes

design, installation, testing, commissioning of

MSDAC evaluation arrangement with all

necessary modules cards, interface cables,

software and other materials etc., execution

of associated work for working of axle

counter through OFC/Quad cable. The

tenderer shall ensure that axle countr

installed by the OEM. Note: Unit to be read as

DP (Detection point) instant of Nos.

39 39 Design, Manufacture, Supply of High Numbers 4.00 474893.00 1899572.00

Frequency Digital Axle Counter Multi-Section

type complete system including central

evaluator(s), final track clearance relay for

each track section, reset boxes, LV boxes,

detection points, mushroom housing for the

trackside electronics and all other

accessories fully wired to the ultimate

capacity and fully equipped for all DPs/Nos of

detection points (incuding interconnection

cards to make common DP or dual DP) this as

per RDSO/SPN/176/2013 version 3.0 or latest.

conforming to existing yard. Inspection by

RDSO. (This includes earthing of track device

if required). Note: Unit to be read as DP

(Detection point) instant of Nos.

40 40 Painting, varnishing, numbering, lettering Station 2.00 38057.00 76114.00

and graphiting of all outdoor and indoor

signalling equipments over and above the

initial painting as per instruction of Railway

representative at site. This includes supply of

paints, varnish, graphites and any other

consumables by the contractor.

KHURDA ROAD DIVISION-S AND T/ECOR

Schedule B1-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All taxes., 2.Supply of

sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of materials to site.,

4.Transportation of released materials from one site to another site or store of concerned SSES/(In-

charge) or as advised by Sr.DSTE/KUR. (Item Directory - Not Applicable)

Item- 3 SUPPLY OF SIGNALLING MATERIALS

S No. Item Description of Item Unit Qty Rate Amount

recorder (Model No. GTM 124 or similar), (II)

slave telephones (3 nos.) (Model No. GTM-

909S or similar), (III) 24V Power supply unit (

01 no) Inspection by RDSO.

2 2 Supply of Magneto Telephone Desk type to Numbers 2.00 7317.00 14634.00

Specification No. IRS: TC-36/97 amd 2. or

IRS:TC 79/2000 Amdt. 4 as per Railway

requirment. Inspection by the Representative

of Sr.DSTE/KUR.

3 3 Supply of Steel Apparatus case 'large Size' as Numbers 50.00 42507.00 2125350.00

per Drg. No - CON/SK/1/1/86 and Spec.No.

IRS:S-10/78 (adv) with latest amnd. with "E"

type lock and key of ward No-32 with handle.

Inspection by RITES.

4 4 Supply of Signal colour light multi unit as per Numbers 2.00 29161.00 58322.00

specification No: IRS: S-26/64 with latest

amendment as per RDSO Spec No.

RDSO/SPN/153/2011 long range working on

110 V- AC 50 Hz complete 3-Aspect suitable

for 140 mm dia. post as per Drg.No:SA-23002

A/M [Adv]. Inspection by RITES.

5 5 Supply of 4.6 Mts CLS tubular steel post Numbers 9.00 11663.00 104967.00

specification No. IRS: S-6/81 with latest Amnd

to suit 140 mm dia base. Inspection by the

6 6 Supply of Ladder 4.5 meter for CLS post as Numbers 4.00 8181.00 32724.00

per Drg. No. SA: 23153 [Adv] Alt-1,

specification No. IRS: S-10/78 (with latest

Amendment) consisting of ladder base,

platform and guarding, ladder support

complete. Inspection by the RITES.

7 7 Supply of Signal Base 140 mm dia [Type Numbers 9.00 5024.00 45216.00

tube] Drg. No. S-2011/M. Inspection by the

8 8 Supply of double walled corrugated pipe 6 Numbers 98.00 4117.00 403466.00

mtr in length, 120 mm outer dia and 103 mm

inner dia, w i t h one suitable coupler

conforming to RDSO Specification No.

RDSO/SPN/204/2011 Version 1.1 Amdt 1 or

latest for under ground cable protection .

C o l o u r- O r a n g e . Inspection by the

Representative of Sr.DSTE/KUR. Note: If

required, the DWC pipe shall be supplied split

9 9 Supply of Perforated G.I. pipe of 100 mm dia Metre 200.00 1889.00 377800.00

with socket. G.I. pipe of make TATA/JINDAL

shall be as per IS: 1239 part-I/2004

Specification for medium gauge and shall be

perforated by drilling 7 mm dia holes length

wise in zig-zag manner staggered at a

distance of 300 mm. Inspection by the

Representative of Sr.DSTE/KUR.

10 10 Supply of Digital multimeter Fluke-287 or Numbers 1.00 114234.00 114234.00

latest higher version with testing lead

complete with case and spare set of

batteries. Inspection by the Representative of

KHURDA ROAD DIVISION-S AND T/ECOR

11 11 Supply of cable route tracer with Integrated Numbers 4.00 451828.60 1807314.40

GPS and Bluetooth, Live GPS data transfer

with Mobile App, through BT, User

configurable frequency and Current direction

indication & 10W Transmitter with minimum

500mA output current and 90V visible on

display, with rechargeable Battery.

Specification as per section H. Make:

adiodetection (RD8200G) or similar. 3 years

OEM warranty. INSPECTION BY RITES.

12 12 Supply of High Power,Electronic Cable Route Numbers 1.00 379188.00 379188.00

Tracer/ Pipe and Cable locating kit with 36

user configurable Active multi frequency

options including 200Hz, 512Hz, 797Hz,

815Hz, 8kHz, 33kHz, 65kHz, 82kHz, 200kHz

upto 476.2kHz, passive detection @ 50Hz for

power cables, Radio Mode for locating

metallic utilities whether energised or not,

Current measurement, LCD Display with left-

right arrow function , Modes: peak, peak with

arrow, pin point peak and null modes,

Compass function; Depth measurement.

Supply includes locating receiver, Transmitter

(Max power : 12Watt) with Li-ion

Rechargeable Batteries for both Transmitter

& Receiver, Battery charger, Induction Signal

Clamp 4'', supplied in a carry bag. Similar to

3M-Dynate/Radio detection/Stanlay

Pathfinder LOC10. Inspection by RITES.

13 13 Supply of Permanently lubricated two layer Kilometre 7.50 132496.00 993720.00

type HDPE duct, outer dia 40 mm, inner dia

33 mm with three end plugs and two

couplers for every Km length of pipe in

length of 500 m confirming to RDSO Spec.

No. RDSO/SPN/TC/45/2013.Rev.2.0

Amendment 2.0 or latest. Inspection by

RITES. Note: The HDPE Duct should be pre

inserted with 4 mm nylon rope, inside the

14 14 Supply of Thermo shrink jointing kit for Numbers 55.00 6143.00 337865.00

underground cable as per Specn No. IRS: TC-

77/2012 [Rev.3] Amd 3. (Cable jointing kit

shall be procured from RDSO approved

sources only). Inspection by the

Representative of Sr.DSTE/KUR.

15 15 Supply of Steel Apparatus case 'Half Size' as Numbers 26.00 25868.00 672568.00

per rg.No.S&T/CON/BBS/92/90 with 'E' type

lock & Key. Ward No. 32. Inspection by RITES.

16 16 Hand Held 200 Khz Digital Multimeter . Numbers 8.00 40592.00 324736.00

MAKE- FLUKE/ YOKOWAGA .MakeiBrand:-

FLUKE 87V. Inspection by the Representative

of Sr.DSTE/KUR.

17 17 Supply of Ladder 3.5 meter for CLS post as Numbers 5.00 5745.00 28725.00

per Drg. No. SA: 23150 [Adv] Alt-1,

specification No. IRS: S-10/78 (with latest

Amendment) consisting of ladder base,

platform and guarding, ladder support

complete. Inspection by the RITES.

18 18 Supply of Insulated flexible wirerope steel Kg 750.00 411.87 308902.50

galvanized 7 X 7strands. Inspection by the

Representative of Sr.DSTE/KUR.

19 19 Supply of optical fibre joint closure for Numbers 16.00 5669.00 90704.00

straight through joint with modification for 24

fibre as per RDSO Specn No.

RDSO/SPN/TC/68/2014, Revision 0.1 Amnd. 1

or latest. Inspection by the Representative of

KHURDA ROAD DIVISION-S AND T/ECOR

20 20 Supply of Signal colour light multi unit as per Numbers 2.00 38099.00 76198.00

specification No: IRS: S-26/64 with latest

amendment as per RDSO Spec No.

RDSO/SPN/153/2011 long range working on

110 V- AC 50 Hz complete 4-Aspect suitable

for 140 mm dia. post as per Drg.No:SA-23001

A/M, (Adv). Inspection by RITES.

21 21 Supply & Uploading of software for Numbers 1.00 80038.00 80038.00

upgradation of Datalogger as per Spec. No.

IRS:S-99/2006. Inspection by the

Representative of Sr.DSTE/KUR.

22 22 Digital Clamp Meter - True RMS type - for Numbers 4.00 16314.32 65257.28

measuring both AC & DC parameters of

various electronic equipment. MAKE: FLUKE

/MECO /BENNING. Inspection by RITES.

23 23 Supply of Handheld Digital Insulation Tester Numbers 5.00 16407.33 82036.65

with separate ranges of 50 V, 100V, 250 V,

500 V, 1000V with additionalfeature of multi

metering of voltage continuity and low

resistance. Inspection by RITES.

24 24 Supply of Signal colour light multi unit as per Numbers 5.00 19082.00 95410.00

specification No: IRS: S-26/64 with latest

amendment as per RDSO Spec No.

RDSO/SPN/153/2011 long range working on

110 V- AC 50 Hz complete 2-Aspect suitable

for 140 mm dia. post as per Drg.No:SA-23003

A/M [Adv]. Inspection by the RITES.

25 25 Supply of Polythenes insulated, polythene Kilometre 0.10 465510.00 46551.00

sheathed, jelly flled telecommunicaton cables

having annealed copper conductors

polythene insulated colour coded cores

twisted into pairs laid up and fully flled with

petroleum jely, taped cable applied with poly

aluminium laminated moiture barrier,

polythene sheathed and double steel taped

armoured and jacketed cable conforming to

Spec.No.IRS:TC41/97 with amendment No.1

or latest 50 pair x 0.63 mm dia. Drum Size

500 meters. ( Warranty Period : Upto 30

months from the date of supply). Inspection

by Representative of Sr.DSTE/KUR.

Schedule B2-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All taxes., 2.Supply of

sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of materials to site.,

Schedule 4.Transportation of released materials from one site to another site or store of concerned SSES/(In-

charge) or as advised by Sr.DSTE/KUR. (Item Directory - Not Applicable) (Item Directory - Not

Item- 4 SUPPLY OF SIGNALLING MATERIALS

S No. Item Description of Item Unit Qty Rate Amount

1 1 Supply of LED signal lamps RED aspect for Numbers 13.00 8401.60 109220.80

main color light signals for railway signaling

as per RDSO.( Warranty Period : Upto 60

months from the date of supply). Inspection

2 2 Supply of Integrated LED Signal for YELLOW Numbers 13.00 8401.60 109220.80

aspect as per RDSO Specification No.

RDSO/SPN/199/2010Rev1.1 or latest. (

Warranty Period : Upto 60 months from the

date of supply).Inspection by RDSO.

3 3 Supply of Integrated LED Signal for GREEN Numbers 13.00 9581.60 124560.80

aspect as per RDSO Specification No.

RDSO/SPN/199/2010Rev1.1 or latest. (

Warranty Period : Upto 60 months from the

date of supply). Inspection by RDSO.

KHURDA ROAD DIVISION-S AND T/ECOR

Schedule B3-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All taxes., 2.Supply of

sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of materials to site.,

Schedule 4.Transportation of released materials from one site to another site or store of concerned SSES/(In-

charge) or as advised by Sr.DSTE/KUR. (Item Directory - Not Applicable) (Item Directory - Not

Applicable) (Item Directory - Not Applicable)

Item- 5 SUPPLY OF SIGNALLING MATERIALS

S No. Item Description of Item Unit Qty Rate Amount

1 1 Supply of Relay AC Immune, plug-in type, Numbers 70.00 6428.00 449960.00

style 'QNA1', Neutral line, 24V DC 8F/8B

contacts, Front and back contacts metal to

carbon, complete with plug board, retaining

clip and connectors conforming to

BRS:931A,IRS : S - 60, IRS : S - 34, IRS : S - 23

(As applicable). Interlocking code : ABDGH.

Inspection by RDSO.

2 2 Relay plug in type, Style AC-LED: ALL aspect, Numbers 35.00 7878.00 275730.00

AC lamp proving Relay unit within built

current transformer type, slow release

neutral line relay, 4F/4B contact , front and

back contact metal to carbon shall be

suitable for working in series with 110V AC,

LED signal lamp rated at 15W conforming to

RDSO Spec No- STS/E/Relay/AC lit

LED/signal/09-2002, Amdt. 1, BRS : 941A ,

IRS : S :3 4 & IRS : S : 23 {as applicable}. The

interlocking code for this unit shall be

ABDHK. Inspection by RDSO.

Schedule C -SUPPLY & EXECUTION OF DRAWING WORK : RATES ARE INCLUSIVE OF:1.All taxes.,

2.Supply of sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of

Schedule materials to site., 4.Transportation of released materials from one site to another site or store of

concerned SSES/(In-charge) or as advised by Sr.DSTE/KUR. (Item Directory - Not Applicable) (Item

Directory - Not Applicable) (Item Directory - Not Applicable)

Item- 6 SUPPLY & EXECUTION OF DRAWING WORK

S No. Item Description of Item Unit Qty Rate Amount

1 1 Compilation, preparation, correction, Per Page 850.00 25.00 21250.00

updating, printing and supply of Final station

working rules with contractor's stationery,

tools, plants and materials. Note: Final SWR

to be submitted in 2 sets for each station.

2 2 Printing and supply of approved SWR with Per Page 1000.00 4.00 4000.00

contractor's stationery, tools, plants and

materials. Note: Approved SWR to be

submitted in 6 copies for each station.

3 3 Compilation, preparation, printing, binding Per Page 200.00 25.00 5000.00

and supply of Draft station/Gate working

rules both in English and Hindi using MS word

software in computer on the basis of WRD,

RCC and Front plate diagram of Panel/VDU

with contractor's stationery, tools, plants &

4 4 Design of SIP & submission of Three paper Set 4.00 36520.00 146080.00

copies for approval.For a Four-Line Station

5 5 Design of SIP & submission of Three paper Set 1.00 76591.00 76591.00

copies for approval.For a Six-Line Station

6 6 Design of SIP & submission of Three paper Set 1.00 97667.00 97667.00

copies for approval. For a Eight-Line Station

7 7 Design of SWRD & submission of Three paper Set 4.00 17628.00 70512.00

copies for approval.For a Four-Line Station

8 8 Design of SWRD & submission of Three paper Set 1.00 36472.00 36472.00

copies for approval.For a six-Line Station

9 9 Design of SWRD & submission of Three paper Set 1.00 43015.00 43015.00

copies for approval. For a Eight-Line Station

KHURDA ROAD DIVISION-S AND T/ECOR

10 10 Alteration of Existing SWRD & submission of Station 1.00 2596.00 2596.00

Three paper copies for approval.For a Four-

11 11 Design of Cable Route Plan (Distant to Set 3.00 8815.00 26445.00

Distant) & submission of Three paper copies

for approval. For a Four-Line Station

12 12 Design of Cable Route Plan (Distant to Set 1.00 24619.00 24619.00

Distant) & submission of Three paper copies

for approval. For a six-Line Station

13 13 Design of Cable Route Plan (Distant to Set 1.00 29286.00 29286.00

Distant) & submission of Three paper copies

for approval. For a Eight-Line Station or more.

14 14 Supply of Original Tracing of SIP after Numbers 4.00 730.00 2920.00

incorporating all the corrections. For a Four-

15 15 Supply of Original Tracing of SIP after Numbers 1.00 866.00 866.00

incorporating all the corrections. For a Six-

16 16 Supply of Original Tracing of SIP after Numbers 2.00 1013.00 2026.00

incorporating all the corrections.For a Eight-

Line Station or more.

17 17 Supply of Original Tracing of SWRD after Numbers 4.00 528.00 2112.00

incorporating all the corrections. For a Four-

18 18 Supply of Original Tracing of SWRD after Numbers 1.00 729.00 729.00

incorporating all the corrections. For a Six-

19 19 Supply of Original Tracing of SWRD after Numbers 1.00 916.00 916.00

incorporating all the corrections. For a Eight-

Line Station or more.

20 20 Supply of Original Tracing of Cable Route Numbers 4.00 1411.00 5644.00

Plan (Distant to Distant) after incorporating

all the corrections. For a Four-Line Station

21 21 Supply of Original Tracing of Cable Route Numbers 1.00 1752.00 1752.00

Plan (Distant to Distant) after incorporating

all the corrections. For a Six-Line Station

22 22 Supply of Original Tracing of Cable Route Numbers 1.00 1977.00 1977.00

Plan (Distant to Distant) after incorporating

all the corrections. For a Eight-Line Station or

23 23 Supply of Original Tracing of Location Box Station 4.00 2644.00 10576.00

Drawings (Including Contact Analysis, Fuse

Particulars etc) after incorporating all the

corrections. For a Four-Line Station

24 24 Supply of Original Tracing of Location Box Station 1.00 3647.00 3647.00

Drawings (Including Contact Analysis, Fuse

Particulars etc) after incorporating all the

corrections. For a Six-Line Station

25 25 Supply of Original Tracing of Location Box Station 1.00 5491.00 5491.00

Drawings (Including Contact Analysis, Fuse

Particulars etc) after incorporating all the

corrections. For a Eight-Line Station or more.

26 26 Supply of Amonia Print of Approved SIP .For a Numbers 24.00 44.00 1056.00

Four-Line Station

27 27 Supply of Amonia Print of Approved SIP .For a Numbers 6.00 46.00 276.00

Six-Line Station

28 28 Supply of Amonia Print of Approved SIP . For Numbers 7.00 46.00 322.00

a Eight-Line Station or more.

29 29 Supply of Amonia Print of Approved Numbers 34.00 44.00 1496.00

SWRD.For a Four-Line Station

30 30 Supply of Amonia Print of Approved Numbers 11.00 46.00 506.00

SWRD.For a Six-Line Station

31 31 Supply of Amonia Print of Approved SWRD. Numbers 11.00 46.00 506.00

For a Eight-Line Station or more.

KHURDA ROAD DIVISION-S AND T/ECOR

32 32 Supply of Amonia Print of Approved Cable Numbers 29.00 44.00 1276.00

Route Plan(Distant to Distant). For a Four-

33 33 Supply of Amonia Print of Approved Cable Numbers 11.00 46.00 506.00

Route Plan(Distant to Distant). For a Eight-

Line Station or more.

34 34 Supply of Amonia Print of Approved Cable Numbers 11.00 46.00 506.00

Route Plan(Distant to Distant). For a Six-Line

Station or more.

35 35 Supply of Amonia Print of Approved Cable Station 12.00 46.00 552.00

Route Plan(mid section). For a Six-Line

36 36 Alteration of Existing RCC & submission of Station 1.00 2596.00 2596.00

Three paper copies for approval. For a Four-

37 37 Design of RCC & submission of Three paper Set 7.00 17628.00 123396.00

copies for approval.For a Four-Line Station

38 38 Supply of Original Tracing of RCC after Numbers 7.00 705.00 4935.00

incorporating all the corrections. For a Four-

39 39 Supply of Amonia Print of Approved RCC. For Numbers 12.00 44.00 528.00

a Four-Line Station

40 40 Alteration of Existing Circuit Diagrams Sheet 750.00 350.00 262500.00

consisting of the items as mentioned below &

submission of Three paper copies for

approval. (i) Wiring Diagrams, (ii) Relay

Disposition Charts, (iii ) Contact Analysis and

Fuse Particulars, (iv) Panel Termination

Chart, (v) CT Rack Particulars & (vi) Input &

Output Bit Chart for EI Systems

41 41 Design of Cable Distribution Plan & Set 3.00 7077.00 21231.00

submission of Three paper copies for

approval. For a Four-Line Station

42 42 Design of Cable Distribution Plan & Set 1.00 16589.00 16589.00

submission of Three paper copies for

approval. For a Six -Line Station

43 43 Design of Cable Distribution Plan & Set 1.00 23562.00 23562.00

submission of Three paper copies for

approval.For a Eight-Line Station or more.

44 44 Supply of Original Tracing of Cable Numbers 4.00 1411.00 5644.00

Distribution Plan after incorporating all the

corrections. For a Four-Line Station

45 45 Supply of Original Tracing of Cable Numbers 1.00 1752.00 1752.00

Distribution Plan after incorporating all the

corrections. For a Six-Line Station

46 46 Supply of Original Tracing of Cable Numbers 1.00 1977.00 1977.00

Distribution Plan after incorporating all the

corrections. For Eight-Line Station or more.

47 47 Supply of Original Tracing of Goomty Station 5.00 3878.00 19390.00

Drawings (Including Relay Disposition Chart,

Contact Analysis, Fuse Particulars, CT Rack

Particulars and Floor Plan etc) after

incorporating all the corrections. For a Four-

48 48 Supply of Amonia Print of Approved Circuit Station 4.00 4583.00 18332.00

Diagrams consisting of the items as

mentioned below. (i) Wiring Diagrams, (ii)

Relay Disposition Charts, (iii ) Contact

Analysis and Fuse Particulars, (iv) Panel

Termination Chart & (v) CT Rack Particulars.

For a Four-Line Station

49 49 Supply of Amonia Print of Approved Goomty Station 5.00 705.00 3525.00

Drawings ((Including Relay Disposition Chart,

Contact Analysis, Fuse Particulars, CT Rack

Particulars and Floor Plan etc). For a Four-

KHURDA ROAD DIVISION-S AND T/ECOR

50 50 Supply of Amonia Print of Approved Goomty Station 1.00 1464.00 1464.00

Drawings ((Including Relay Disposition Chart,

Contact Analysis, Fuse Particulars, CT Rack

Particulars and Floor Plan etc). For a Eight-

Line Station or more.

51 51 Alteration of Existing Location Box Drawings Sheet 360.00 451.00 162360.00

(Including Contact Analysis, Fuse Particulars

etc) and submission of Three paper copies for

52 52 Alteration of Existing Goomty Drawings Sheet 106.00 901.00 95506.00

(Including Relay Disposition Chart, Contact

Analysis, Fuse Particulars, CT Rack

Particulars and Floor Plan etc) and

submission of Three paper copies for

53 53 Supply of Original Tracing in A-3 Size. NOTE:- Sheet 850.00 71.00 60350.00

For Drawings larger than A-3 Size, payment

shall be made in multiples of A-3 Size.

54 54 Supply of Amonia Prints in A-3 Size. NOTE:- Sheet 2850.00 19.00 54150.00

For Drawings larger than A-3 Size, payment

shall be made in multiples of A-3 Size.

55 55 Design of Location Box Drawings (Including Station 2.00 1763.00 3526.00

Contact Analysis, Fuse Particulars etc) and

submission of Three paper copies for

approval. For a Four-Line Station.

56 56 Design of Location Box Drawings (Including Station 1.00 2735.00 2735.00

Contact Analysis, Fuse Particulars etc) and

submission of Three paper copies for

approval. For a Six-Line Station.

57 57 Design of Location Box Drawings (Including Station 1.00 3661.00 3661.00

Contact Analysis, Fuse Particulars etc) and

submission of Three paper copies for

approval. For a Eight-Line Station or more.

58 58 Supply of Amonia Print of Approved Cable Numbers 18.00 44.00 792.00

Distribution Plan. For a Four-Line Station.

59 59 Supply of Amonia Print of Approved Cable Numbers 6.00 46.00 276.00

Distribution Plan.For a Eight-Line Station or

60 60 Supply of Amonia Print of Approved Cable Numbers 6.00 46.00 276.00

Distribution Plan.For a Six-Line Station or

61 61 Supply of Original Tracing of Circuit Diagrams Station 2.00 26442.00 52884.00

consisting of the items as mentioned below

after incorporating all the corrections. (i)

Wiring Diagrams, (ii) Relay Disposition

Charts, (iii ) Contact Analysis and Fuse

Particulars, (iv) Panel Termination Chart, (v)

CT Rack Particulars & (vi) Input & Output Bit

Chart for EI Systems. For a Four-Line Station

62 62 Supply of Original Tracing of Circuit Diagrams Station 1.00 33736.00 33736.00

consisting of the items as mentioned below

after incorporating all the corrections. (i)

Wiring Diagrams, (ii) Relay Disposition

Charts, (iii ) Contact Analysis and Fuse

Particulars, (iv) Panel Termination Chart, (v)

CT Rack Particulars & (vi) Input & Output Bit

Chart for EI Systems. For a Six-Line Station

63 63 Supply of Original Tracing of Circuit Diagrams Station 1.00 41184.00 41184.00

consisting of the items as mentioned below

after incorporating all the corrections. (i)

Wiring Diagrams, (ii) Relay Disposition

Charts, (iii ) Contact Analysis and Fuse

Particulars, (iv) Panel Termination Chart, (v)

CT Rack Particulars, (vi) Input & Output Bit

Chart for EI Systems. For a Eight-Line Station

KHURDA ROAD DIVISION-S AND T/ECOR

submission of Three paper copies for

approval, For a Six-Line Station

65 65 Design of Track Bonding Plan & submission of Set 1.00 6699.00 6699.00

Three paper copies for approval. For a Four-

66 66 Design of Circuit Diagrams consisting of the Station 1.00 132211.00 132211.00

items as mentioned below & submission of

Three paper copies for approval. (i) Wiring

Diagrams, (ii) Relay Disposition Charts, (iii )

Contact Analysis and Fuse Particulars, (iv)

Panel Termination Chart, (v) CT Rack

Particulars & (vi) Input & Output Bit Chart for

EI Systems. For a Four-Line Station

67 67 Design of Goomty Drawings (Including Relay Station 1.00 3525.00 3525.00

Disposition Chart, Contact Analysis, Fuse

Particulars, CT Rack Particulars and Floor

P l a n etc) and submission of Three paper

copies for approval, For a Four-Line Station.

68 68 Supply of Original Tracing of Cable Route Numbers 1.00 1750.00 1750.00

Plan (Mid Section) after incorporating all the

corrections. For a Six-Line Station

69 69 Supply of Amonia Print of Approved Cable Numbers 6.00 46.00 276.00

Route Plan(Mid Section). For a Six-Line

70 70 Supply of eight sets of Amonia Print of Station 1.00 364.00 364.00

Approved Completion Cable Route Plan(Mid

Section). For a Six-Line Station

71 71 Supply of eight sets of Amonia Print of Station 1.00 366.00 366.00

Approved Completion SIP .-For a Eight-Line

Station or more

72 72 Alteration of Existing SWRD & submission of Station 1.00 8904.00 8904.00

Three paper copies for approval-For a Eight-

Line Station or more

73 73 Alteration of Existing RCC & submission of Station 1.00 8904.00 8904.00

Three paper copies for approval-For a Eight-

Line Station or more