Building Electrification of block 108C at INRP site,Tarapur

Amount

Supply, Installation, Testing and Commissioning of following configuration 415V, 3-phase, 4 wire, double door, with R Y B Phase indication and MCB position indication through glass front, IP-54, Prewired with HFFR copper wires, horizontal type, metallic Double Door, Phase Segregated three pole and neutral MCB Distribution Board fabricated out of 2 mm thick, powder coated with RAL7035 shade, pre-galvanized G.I. sheet steel, suitable for surface mounting/installation in existing enclosure complete with appropriate rating of tinned copper bus bar/ Cu wire, neutral bus bar, earth bar, din bar, brass neutral link, brass earthing studs, phase distribution drawing, danger board, name plate, 2 mm thick removable gland plate on both top and bottom side with required number of knock out holes, neoprene gasket, etc. as per drawing, specifications & generally as per relevant IS, SLD, Technical specification & as per instructions of Engineer-in-charge.

MCB DB with Incomer of 25A, Isc=10kA, Type C, TPN MCB with 2-Pole, 25A, Isc=10kA, (100mA) RCBO for each phase and 12 nos. of 16A, Isc=10kA, Type C, SPN Ougoing MCB feeder as per SLD and technical specification.

Supply

Installation

MCB DB with Incomer of 25A, Isc=10kA, Type C, TPN MCB with 2-Pole, 25A, Isc=10kA, (100mA) RCBO for each phase and 18 nos. of 16A, Isc=10kA, Type C, SPN Ougoing MCB feeder as per SLD and technical specification.

Supply

Installation

MCB DB with Incomer of 25A, Isc=10kA, Type C, TPN MCB with 2-Pole, 25A, Isc=10kA, (100mA) RCBO for each phase and 24 nos. of 16A, Isc=10kA, Type C, SPN Ougoing MCB feeder as per SLD and technical specification.

Supply

Installation

Supply, Installation, Testing and Commissioning of following configuration 240V, 1-phase, 2 wire, with Phase indication and MCB position through glass front, Pre wired with HFFR copper wires, IP-54, MCB Distribution Board fabricated out of 2mm thick Pre Galvanized G. I sheet steel, powder coated with RAL7035 shade, suitable for surface mounting/installation in existing enclosure complete with appropriate rating of tinned copper bus bar/Cu Wire, neutral bus bar, brass neutral link, brass earthing studs, phase distribution drawing, danger board, name plate, earth bar, din bar for MCB mounting, 2 mm thick removable gland plate on both top and bottom side with required number of knock out holes, neoprene gasket, check-nuts etc. as required as per drawing, specifications & generally as per relevant IS & as per instructions of Engineer-in- charge.

MCB DB with Incomer of 40A, Isc=10kA, Type C, DP MCB 40A DP RCBO (100mA) and 8 nos. of 16A, Isc=10kA, Type C, SPN Ougoing MCB feeder as per SLD and technical specification.

Supply

Installation

MCB DB with Incomer of 63A, Isc=10kA, Type C, DP MCB 40A DP RCBO (100mA) and 12 nos. of 16A, Isc=10kA, Type C, SPN Ougoing MCB feeder as per SLD and technical specification.

Supply

Installation

Supply and Installation of the following Industrial/modular MCB and metal clad/polycarbonate plug sockets with suitable industrial plug tops ( 3-pin) along with surface mounted powder coated GI Box with suitable mounting arrangements on wall and 3 pin domestic plug sockets with suitable PVC Box, switch and plug tops as per Technical specifications.

1 nos. of 10A and 1 nos. of 20A, Single phase Industrial Socket with Isc=10kA, Type C-Curve, Industrial type MCB for each Socket along with pre- Galvanised powder coated GI sheet steel Face Plate, Industrial Plug Tops and suitable DIN rail and mounting arrangements along with surface mounted powder coated 2mm thick GI Box with suitable mounting arrangements on wall as per technical specification.

Supply

Installation

1 no. of 6A and 1 no of 16A, Single phase Industrial three pin Socket with corresponding Type C-Curve, Industrial type MCBs, Isc=10kA, along with pre- powder coated GI sheet steel Face Plate, Industrial Plug Tops and suitable DIN rail and mounting arrangements as per technical specification.

Supply

Installation in existing embedded GI Box

1 nos. of 10A Single phase Industrial Socket with Isc=10kA, Type C-Curve, Industrial type MCB for Socket along with pre- Galvanised powder coated GI sheet steel Face Plate, Industrial Plug Tops and suitable DIN rail and mounting arrangements along with surface mounted powder coated 2mm thick GI Box with suitable mounting arrangements on wall as per technical specification.

Supply

Installation

1 no of 6A and 1 no of 16A, Single phase Modular Decorative Type Socket with Polycarbonate box, piano Switch for each Socket and heavy duty polycarbonate Face Plate, along with concealed/surface mounted enclosure, plug tops and suitable surface mounting arrangements as per technical specification.

Supply

Installation

1 nos. of 6/10A,Single phase Industrial Socket in Pre-Galvanised powder coated 2mm thick GI sheet Box,suitable for surface mounting, industrial plug top with chained metal cover for the socket outlet,suitable din-rail,face plate,suitable copper lugs,plug-tops,SS screw/nut bolts for surface mounting.

Supply

Installation

1 nos. of 6/10A,Single phase Industrial Isc=10kA, Type C-Curve, Industrial type MCB Switch box in Pre-Galvanised powder coated 2mm thick GI sheet Box,suitable for surface mounting,,suitable din-rail,face plate,suitable copper lugs,plug-tops,SS screw/nut bolts for surface mounting.

Supply

Installation

2 nos. of 6/10A,Single phase Industrial Isc=10kA, Type C-Curve, Industrial type MCB Switch box in Pre-Galvanised powder coated 2mm thick GI sheet Box,suitable for surface mounting,,suitable din-rail,face plate,suitable copper lugs,plug-tops,SS screw/nut bolts for surface mounting.

Supply

Installation

3 nos. of 6/10A,Single phase Industrial Isc=10kA, Type C-Curve, Industrial type MCB Switch box in Pre-Galvanised powder coated 2mm thick GI sheet Box,suitable for surface mounting,,suitable din-rail,face plate,suitable copper lugs,plug-tops,SS screw/nut bolts for surface mounting.

Supply

Installation

Supply, Fabrication and Installation of Standard steel sections as per IS 2062 Grade BR for equipment supports, base frame for panels, wall frames and brackets for installation of lights/ equipments, earth pit cover plates, Anchor Fastners etc. Fabrication shall include drilling, entiling, welding wire brush cleaning, testing DPT etc., supply of all consumables like gas, approved welding rods, Zinc coating paint finish during installation as per EIC and tender tech spec. After fabrication two coats of epoxy based primer and two coats of finish paints shall be applied.

Supply of Single Core HFFR wires (Copper) of size mentioned below in voltage grade 1100 V as per the IS: 3961 (part V) - 1968. As per conductor class 2 of IS: 8130 / 1984 as per technical specification

Installation/drawing through concealled/ surface conduit and wiring, wire connection through Push wire Inline Splicing Connector for solid and stranded wires upto 2.5 sqmm, transparent housing, Transparent cover and termination at both ends of Single Core HFFR wires ( Copper ) of size mentioned below in voltage grade 1100 V as per the IS: 3961 ( part V ) - 1968. As per conductor class 2 Type-C of IS: 8130 / 1984 as per technical specification

Supply, Installation, Testing and Commissioning of LED light fittings with light fitting accessories, including supply of fixing SS accessories, flexible GI metallic conduit sleeves, PVC conduit bushes, Cu cable lugs, complete with light fitting accessories, including supply of fixing accessories, twin twisted tinned 1.5 sq. mm copper flexible cords for terminal connections, 16 SWG copper wire for earthing , flexible GI metallic conduit sleeves, PVC conduit bushes, cable lugs and testing and commissioning as per the specification of the following:

Industial box type, 4ft Functional with 2x18W LED replaceble type Tube with light fitting accessories, including supply of fixing SS accessories, flexible GI metallic conduit sleeves, PVC conduit bushes, Cu cable lugs, with a nominal system lumen output of 2350 lumens per LED tube. The luminaire should have a color temperature of 6500K and CRI>80. minimum 110 lm/w efficacy, THD < 10% and PF > 0.95. The batten luminaire housing should made of white powder coated CRCA sheet steel. The LED shall be mounted on extruded aluminium strip which acts as heat sink and is intergral part of tube which is made up of polycarbonate material which gives diffused light. The total power consumption should not exceed 44W (including driver).

Supply

Installation, Testing and Commissioning

LED Bulkhead with a nominal system lumen output of not more than 1100 lumens and a minimum system efficacy of 110 lm/W. The luminaire should have a color temperature of 6500K and CRI > 80. The luminaire shall meet IP66 rating and IK 08 rating with THD < 20% and PF > 0.9. The luminaire housing should made of High pressure die cast Aluminium with high quality PMMA diffuser. The total power consumption should not exceed 10W (including driver).

Supply

Installation, Testing and Commissioning

LED Lowbay light fitting complete with light fitting accessories, including supply of fixing SS accessories, flexible GI metallic conduit sleeves, PVC conduit bushes, Cu cable lugs, LED Low bay wide beam of 35W having System Efficacy >120 lm/W, lumen output of 4300lumens system output THD <10%, Power Factor >0.95, CRI >80, , CCT 6500, Full IP 65 protected pressure die cast aluminium (LM6) housing having integrated PC lens cover with Impact resistance IK08. Operating temp. -10 degrees to 50 degrees C. BIS compliant driver, EMC -EMI compliant. Driver shall have 10KV Surge protection. Shall have eye bolt hook for surface/ suspended mounting.

Supply

Installation, Testing and Commissioning

LED Flatline light fitting complete with light fitting accessories, including supply of fixing SS accessories, flexible GI metallic conduit sleeves, PVC conduit bushes, Cu cable lugs, LED with wide beam of 32W having System Efficacy >120 lm/W, lumen output of 3300lumens system output THD <10%, Power Factor >0.95, CRI >80, , CCT 6500, Full IP 20 protected pressure die cast aluminium (LM6) housing having integrated PC lens cover with Impact resistance IK08. t. Driver shall have 4KV Surge protection. Shall be suspended at proper height.

Supply

Installation, Testing and Commissioning

LED peripheral luminaire with a normal system lumen output of 4200 lumens and minimum efficacy of not less than 120lumen/watt. The luminaire should have CCT of 5700K and a CRI>70.The luminaire shall meet IP66,IK07 rating with THD<10% & pf>0.9. The luminaire housing should be made of pressure die cast aluminium. The total power consumption should not exceed 25W (including BIS compliant integrated driver) and other requirements shall be as per tender technical specifications.

Supply

Installation, Testing and Commissioning

Supply and surface conduiting of heavy duty rigid GI ERW conduit pipe of 25mm sizes along with all accessories such as inspection bends, junction box, socket, check nut, etc. including making threads, removing burrs, connection of accessories, drawing of fish wire, cleating with heavy duty GI saddle or suit to site clamps on RCC wall, column, steel structure . as required under the instruction of Engineer in charge. 2mm thick powder coated GI surface type junction box with suitable mounting arrangements shall be provided.

Supply

Installation

Supply and laying of 14 SWG ETP grde bare solid copper conductor throughout along the conduit including fixing with ties, brazing etc as required.

Supply

Installation

Supply of required material and making of exothermic braze joints of copper conductor with other conductor or copper earthing pad including removal of burrs and debris as per technical specification and instruction of engineer in charge.

Supply of Print, Copy, Scan, Send and Optional Fax ,Highly Efficient A3 Monochrome Laser Multifunctional printers with feature such as platen cover type z,inner finisher with 2 Tray ,545 sheet capacity ,Inner 2 wqay Tray M1,cassette feeding unit

Installation

POZITRON ENGINEERING SYSTEMS (BID ID -3259925)