REPAIR/ MAINT OF PUMPS, MOTORS, STARTERS, CONTROL PANELS AND CHLORINATION PLANT AND FILTRATION PLANT AT SWIMMING POOL , CI/GI PIPE LINE, CONTROL VALVES AND CLEANING/PAINTING OF OH TANK AT MIRAN SAHIB UNDER GE JAMMU .

Amount

Supply and fixing in replacement of tubing GI "MG" 15 mm bore dia fixed to wall, on floor complete with fitting including taking down existing tubing all as specified and directed

Dismentaling and taking down electric motor of dozing system and shifting in workshop for repair and rewinding with super enamelled copper winding wire of same gauge and nos of turns complete with insulated material i.e. varnish,cotton tape,bamboo strips,emory paper and drying including replacement of UNSV spare parts .(Spare parts shall be measured and paid separatly under respective items)

Supply only motor seal

Supply only motor bearing

Supply only motor fan blade

Supply only rotor shaft

Supply only coupling

Dismantaling and taking down dozing pumping set and shifting in workshop for repair/maintenance/overhauling and reassembly after necessary repair complete with and including replacement of UNSV/defective spare parts and tested on load at site complete all as specified and directed (Spare parts shall be measured and paid separatly under respective items)

Supply only Agitator assembly

Supply only Agitator bearing

Supply only Agitator Shaft with ss blade duty FRP coated

Supply only foot valve

Supply only suction Valve

Supply only discharge valve

Supply only injection fitting

Supply only PE tubing 5/8'' (8 mtr)

Supply only solenoid motor

Supply only main head (PP/PVC)

Supply only main head hex bolts

Supply only diphragm(taflon faced)

Supply only Acrylic front cover

Supply only speed/stroke nob

Supply only togle switch

Supply only strainer for foot valve

Supply only electronic controlled circuit plate

Supply only NRV Spring

Supply only Air release valve

Supply only power cable three core copper 2.5 sqmm with plug

Supply only injection check valve(NRV)

Supply and fixing in replacement of heavy duty FRP service tank 150 liters comlete with drain valve , level gauge ,water inlet/outlet provn and CPV 15 mm pipe for feeding to main line complete all as specified and directed

M&L for fabricated MS Angle iron frame heavy duty epoxy coated & anticorrosive paint bend to shape bending ,welding and fixing on wall/floor to take the load of complete dozing system to avoid direct load of motor on tank complete as specied and directed by the Engr-in-Charge

Supply and fixing in replacement of chlorine test kit with coloured sample complete with all testing fillaments and OT solution in rexin finish wooden box all as specified and directed.

Supply and fixing in replacement of water pressure gauge 7Kg/10Kg heavy duty 100mm dia complete with brass sampling cock 3/8" and pressue gauge cock complete all as specified and directed.

Supply and fixing in replacement of OT solution chlorine test(500 ml)

Supply and fixing in replacement of chemcal dozing systems suitabe to injection of disinfection of water treatment having injection capacity 15 LPH comprising of FRP tank 150 ltr capacity an dosing pump (type MAGDOS/MD/20/40) at 10 Kg /cm2 working pressure solinoid driven electrically controlled 220 Volt ,max current 3.3 Amm,power 70 watt ,Single phase with IP 65 protection and F-Class insulted with standard fittings with stroke length suitable from 0-100% including all accessories such as foot valves/motor/agitator with shaft and impeller,PE tubing,dosing tank FRP chemical resistant,inlet/outlet valve,drain vale,gauge,connection lead with plug and MS Angle iron frame made out from 40X40X6mm to take the load of coplete system all as specified Make:Jesco/Declibac/Prominent/Sathya Sai

Supply and fix in replacement Plastic cylindrical sealed disposable sainitizer refill for disinfection of drinking water with arrangement for control release suitable for operation in presurised line set of 25 pieces of Declibac

Supply and fix in replacement multi cavity water sainitizer/conditioning station with proportional dosing arrengement at zero dischage,power free automation system with 100 Ltr PVC tank model EDS PRO covered with lid and overflow valve,inlet outlet and drain vale complete with accessories incl connection with existing system make Declibac

Disconnecting all incoming/outgoing electric connection from LT pannel/starter/electric motor carefully including dismantling/opening nut, bolt of discharge head and taking out submersible/VT motor pumping set complete with MS column pipe having capacity 3 to 5 HP and shifting in workshop for repair/servicing of pumping set and re-assembling/electric connection and testing at site on full load all as specified and directed by Engr-in-Charge

Disconnecting all incoming/outgoing electric connection from LT pannel/starter/electric motor carefully including dismantling/opening nut, bolt of discharge head and taking out submersible/VT motor pumping set complete with MS column pipe having capacity 7.5 to 25 HP and shifting in workshop for repair/servicing of pumping set and re-assembling/electric connection and testing at site on full load all as specified and directed by Engr-in-Charge

Strip opening complete submersible pumping set having capacity 3 to 15 HP any stage/discharge and dismantling all spare parts by opening studs complete with machine/lathe work/grinding/polishing and fitting of all spare parts and re-assembling/ installation in position after necessary repair / replacement of UNSV/defective spare parts (Spare parts shall be measured & paid separately under respective items as under)

(a) Supply only cast iron stage bowl

(b) Supply only cast iron suction discharge chamber

(c) Supply only stainless steel neck ring

(d) Supply only stainless steel bowl bush

(e) Supply only stainless steel coupling sleeves

(f) Supply only cast iron impeller with key

(g) Supply only body studs fully threaded

(h) Supply only stainless steel pump shaft

(j) Supply only stainless steel pump shaft coupling with key

(k) Supply only cast iron NRV with NRV seat & cone

(l) Supply only stainles steel sleeves for bowl

(m) Supply only rubber bush

(n) Supply only strainer for pump

All as per ser no 14 above here in before but capacity 20 to 25 HP

(a) Supply only cast iron stage bowl

(b) Supply only cast iron suction discharge chamber

(c) Supply only stainless steel neck ring

(d) Supply only stainless steel bowl bush

(e) Supply only stainless steel coupling sleeves

(f) Supply only cast iron impeller with key

(g) Supply only body studs fully threaded

(h) Supply only stainless steel pump shaft

(j) Supply only stainless steel pump shaft coupling with key

(k) Supply only cast iron NRV with NRV seat & cone

(l) Supply only stainles steel sleeves for bowl

(m) Supply only rubber bush

(n) Supply only strainer for pump

M&L for strip opening to submersible motor/ VT motor having capacity 3 to 15 HP and re-winding with super enamelled copper winding wire heavy duty heat resistence confirming to IS of same gauge and nos of turns complete with realignment of motor slotes and insulating mateials i.e varnishing, bamboo strips, leather papers, cotton tapes including replacement of UNSV/defective spare parts and drying complete and re-assembling after repair/rewinding and testing at site on full head ( spare parts shall be measured & paid separately under respective item as under)

(a) Supply only thrust plate with circlip and key

(b) Supply only thrust plate bearing housing

(c) Supply only bearing for motor

(d) Supply only rubber oil seal

(e) Supply only cast iron sand guard

(f) Supply only rubber diaphragam with plate

(g) Supply only stainless steel sealing bush

All as per ser no 16 above here in before but capacity 20 to 25 HP

(a) Supply only thrust plate with circlip and key

(b) Supply only thrust plate bearing housing

(c) Supply only bearing for motor

(d) Supply only rubber oil seal

(e) Supply only cast iron sand guard

(f) Supply only rubber diaphragam with plate

(g) Supply only stainless steel sealing bush

Labour for welding, metalling, grinding, polishing and lathe/machine work for re-alignment to rotar assembly and making the suitable size for fitment of rotar bearing complete with replacement of UNSV/defective spare parts of capacity 3 to 15 HP (Spare parts shall be measure and paid separately under respective itemsas under)

(a) Supply only rotar sleeves stainless steel

(b) Supply only rotar GM bearing bush

(c) Supply only rotar upper & lower bearing housing

(d) Supply only rotar upper & lower tee bolts

(e) Supply only studs for adopter housing complete with plain washer and hex nut

(f) Supply only GM drain plug

Labour for welding, metalling, grinding, polishing and lathe/machine work for re-alignment to rotar assembly and making the suitable size for fitment of rotar bearing complete with replacement of UNSV/defective spare parts of capacity 20 to 25 HP (Spare parts shall be measure and paid separately under respective itemsas under)

(a) Supply only rotar sleeves stainless steel

(b) Supply only rotar GM bearing bush

(c) Supply only rotar upper & lower bearing housing

(d) Supply only rotar upper & lower tee bolts

(e) Supply only studs for adopter housing complete with plain washer and hex nut

(f) Supply only GM drain plug

Supply and fixing in replacement of submersible cable 16 Sqmm 3 core flat copper conductor heavy duty 1100 volts grade confirming to ISI all as specified and directed by Engr-in-Charge (old cable shall br deposited in store yard)

Supply and fixing in replacement of oil immersed star delta starter heavy duty manual operated suitable for submersible/VT pumping set with overload relay range 37-50 Ampere, 415 volts, 50 Hz, 3 phase confirming to IS complete with initial filling of oil

All as per ser item no 22 here in before but overload relay range 18-25 Amp

Taking out all incoming/outgoing electric connection from LT pannel/starter/motor/voltage stabilizer carefully for repair to cable/rectification the fault and re-connecting in position after repair and preparation the cable and fixing complete with nut, bolts, washers for cable size 25 to 95 Sqmm (NOTE :- Preparation of 3.5 core cable, 4 wire each & will be considerable one job)

Supply and fixing in replacement of submersible motor rotor for 20 to 25 HP motor complete with bearing upper/lower bearing housing, sleeves, tee bolts and bush complete all as specified and directed by Engr-in-Charge

Supply and fixing in replacement of submersible motor stater for capacity 20 to 25 HP complete with thrust plate, thrust bearing with housing, studes, water seal, sand guard, rubber diaphragam with plate, sealing bush complete all as specified and directed by Engr-in-Charge

Material and Labour for febrication of MS clamp made out from flate 150 mmx12 mm thick, bend to shape, drill a hole four nos in each clamp of size 16 mm dia suitable for holding MS column pipe size 150 mm dia. Complete with provn of four nos nuts, both 4" long and washer complete as per sample

Supply and fixing in replacement of cast iron discharge head assembly suitable for vertical turbine plumbing set having suction/discharge size 150 mm dia complete all as specified and directed by Engr-in-Charge

Strip opening complete vertical turbine pumping set having capacity 7.5 to 20 HP any stage/discharge and dismantling all spare parts by opening studs complete with machine/lathe work/grinding/polishing and fitting of all spare parts and re-assembling installation in position after necessary repair / replacement of UNSV/defective spare parts (Spare parts shall be measured & paid separately under respective items as under)

Supply only cast iron bowl

Supply only cast iron suction/discharge bowl

Supply only stainless steel neck ring

Supply only cast iron impellers with key

Supply only stainless steel shaft

Supply only stainless steel coupling with key

Supply only cast iron NRV with seat

Supply only stainless steel bowl bush

Supply only rubber bush

Supply only body studs fully threaded

Supply only stainless steel sleeves

M&L for PCC 1:3:6 type C-1 Using 20 mm stone aggregate mass filling for discharge head base complete with breaking/dismantling existing PCC block all as specified and directed by the Engr-in-Charge

Supply and fixing in replacement of on load open execution change over switch front handle operated 4 pole, 415 volt, 50 Hz 125 Amp confirming to IS all as specified and directed by Engr-in-Charge

Supply and fixing in replacement of on load change over switch side handle operated 4 pole, 415 volt, 50 Hz 100 Amp confirming to IS all as specified and directed by Engr-in-Charge

M&L for febrication of angle iron bracket 40x40x6 mm thick cutting, bend to shape drilling hole 16 mm 4 nos each bracket welding MS flat of 20 mmx3 mm thick in each bracket and fixed on the wall with the help of nut, bolt suitable for run the cable of any size as per site requirement as specified and directed by the Engr-in-Charge

S&F in replacement Chain pully moving chain made out from aprox 10mm dia bar heavy duty with Grade 80 Alloy steel Chain suitable for 5 Ton chain pully block having length 6 mtr coforming to IS-3832/1971.

S&F in replacement of Spur gear chain pully block heavy duty complete with grade 80 alloy steel chain suitable to take load upto 5 Ton capacity with provision of moving chain having length 6 mtr approx conforming to IS.

S&F in replacement of MCCB 4 pole, 125 amp, 16 KA, 415 volt, 50 Hz complete all as specified and directed

Transporting air compressor and other allied equipment/material at site of tube well , and installation of complete machinery .

Re- development of tube well with air compressor of adequate capacity (not less than 250 Cfm) as per specification till the availability of sand free clear water, subject to minimum of 60 hrs of operation of air compressor (60 x 4500)

Providing of pea shaped gravel as per specification and gravel shrouding in annular space between well and liner assembly required during re-development.

Stabilization and yield testing to tube well by using submersible pump of adequate capacity as per specifications (subject to minimum of 48 hrs of development with submersible pump set) including conduction of sounding test ( 48 x 3200) Note:Submersible pumping set of adequate capacity will be brought by contractor at their own cost and rates for hiring submersible motor deems to be included in item rate.

M & L for brick work with sub class 'B' bricks straight or curved on plan not exc. 6 m mean radius built in CM 1:4 for sluice valve pit

M & L for rendering plaster 10 mm thick on fair face of brick work or concrete surface inside sluice valve pit in CM 1:6 complete all as specified and directed

Taking down plaster of any thickness on brick or stone wall of sluice valve pit including racking out joints, hacking for key, scrubing down, of any description

M & L for preparation of rusted or previous untreated surface of old painted surface of sluice valve pit MS sheet cover scrubing, cleaning and painting to sluice valve pit both side of any description over 10 cm in wide or girth not otherwise described and painted with synthetic enamelled black paint two coat over a coat of red oxide primer including writing location/area with white paint all as specified and directed

Taking out UNSV/damage sluice valve pit MS top cover along with angle iron frame for repair, denting, necessary welding work, provn of replacement of two nos of MS hings 6" heavy duty and provn of lifting handle and refixing in position along with angle iron frame with the help of nut, bolt after necessary repair/in position as per site requirement

Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5 M in depth and getting out in soft/loose soil or hard/dense soil for taking up or laying of GI/CI pipe line all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cms.

Removing excavated material not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above starting point.

taking out UNSV sluice valve of size 100/150 mm bore dia in position for repair complete with refacing, regrinding, replacing staffing box of spindle, nut, bolt, washer, rubber gaskits, repair to GM seat with gaskit, gland cup filling gland dori and refixing after repair in site complete all as specified and directed

M & L for replacement of tubing GI "MG" with all fittings laid in floor or trenches including taking out old UNSV pipe of size 100 mm dia complete all as specified and directed

M & L for replacement of tubing GI "MG" with all fittings laid in floor or trenches including taking out old UNSV pipe of size 80 mm dia complete all as specified and directed

M & L for replacement of tubing GI "MG" with all fittings laid in floor or trenches including taking out old UNSV pipe of size 50 mm dia complete all as specified and directed

M & L for replacement of tubing GI "MG" with all fittings laid in floor or trenches including taking out old UNSV pipe of size 40 mm dia complete all as specified and directed

M & L for replacement of tubing GI "MG" with all fittings laid in floor or trenches including taking out old UNSV pipe of size 25 mm dia complete all as specified and directed

M & L for replacement of tubing GI "MG" with all fittings laid in floor or trenches including taking out old UNSV pipe of size 20 mm dia complete all as specified and directed

M & L for replacement of gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 50 mm bore

M & L for replacement of gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 40 mm bore

M & L for replacement of gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 25 mm bore

M & L for replacement of gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 20 mm bore

M & L for replacement of cast iron pipe with spigot & socket ends centrifugally cast class 'B' of any length conforming to ISI laid in trenches of size 150 mm bore

M & L for replacement of cast iron pipe with spigot & socket ends centrifugally cast class 'B' of any length conforming to ISI laid in trenches of size 100 mm bore

M & L for replacement of CI fitting any type, radius and angle for spigot and socketed and flanged pipes, laid piece both end flanged or one end flanged other sockested, cap, plug, dead end flanged, split collar, reducer of any size upto 150 mm bore pipe

M & L for replacement of CI sluice valve PN 1.6 with iron wheel head of size 150 mm bore with stainless steel spindle both end flanged complete with nut, bolts, washer and rubber gaskit 3 mm thick conforming to ISI 14846/2000 complete all as specified and directed make BIR/BVI/Leader/ Kirloskar

M & L for replacement of CI sluice valve PN 1.6 with iron wheel head of size 100 mm bore with stainless steel spindle both end flanged complete with nut, bolts, washer and rubber gaskit 3 mm thick conforming to ISI 14846/2000 complete all as specified and directed make BIR/BVI/Leader/ Kirloskar

M & L for replacement of CI sluice valve PN 1.6 with iron wheel head of size 80 mm bore with stainless steel spindle both end flanged complete with nut, bolts, washer and rubber gaskit 3 mm thick conforming to ISI 14846/2000 complete all as specified and directed make BIR/BVI/Leader/ Kirloskar

M & L for replacement of CI non return valve PN 1.6 of size 150 mm bore with stain less steel working part conforming to ISI 5312/2004 duly IS marked complete with rubber gaskit 3 mm thick and nut, bolts and washer couple all as specified and directed

M & L for replacement of CI air release valve with double orifice with rubber valve of size 150 mm bore conforming to ISI 14845 complete with rubber gaskit and nut, bolts and washer complete all as specified and directed

M & L for replacement of CI single air release valve screwed of size 50 mm bore dia

M & L for replacement of foot valve of size 150 mm bore dia flanged end, lift type conforming to ISI 4038 with stain less steel working part complete with rubber gaskit and nut, bolts washers etc all as specified and directed by Engr-in Charge

M & L for replacement of foot valve of size 80 mm bore dia flanged end, lift type conforming to ISI 4038 with stain less steel working part complete with rubber gaskit and nut, bolts washers etc all as specified and directed by Engr-in Charge

M & L for replacement of foot valve of size 40 mm bore dia flanged end, lift type conforming to ISI 4038 with stain less steel working part complete with rubber gaskit and nut, bolts washers etc all as specified and directed by Engr-in Charge

M & L for replacement of CI split coller of size 150 mm dia complete with rubber gaskit 3 mm thick and nut, bolts, washer etc complete all as specified and directed

M & L for replacement of sluice valve spindle stainless steel suitable for 150 mm sluice valve complete with check nut.

Labour for repair/rectification of leakage of underground water pipe line GI of size 25 to 100 mm dia with excavation Appx 1.0X1.0X1.0 mtr around the leakage, returning filling in,removal,cutting/disconnecting to existing leakage GI Pipe line in position for repair/rectification of leakage,replacement of UNSV fittings and welding work as per site requirement and restore the water supply. Note: (Spare/fitting shall be measured and paid seperatly)

Supply only GI union 100 mm dia

Supply only GI union 40 mm dia

Supply only GI union 25mm dia

Supply only GI union 20 mm dia

Supply only GI Socket 100 mm dia

Supply only GI Socket 40 mm dia

Supply only GI Socket 25 mm dia

Supply only GI Socket 20 mm dia

Supply only GI Elbow 40 mm dia

Supply only GI Elbow 25 mm dia

Supply only GI Elbow 20 mm dia

Supply only GI Tee 40 mm dia

Supply only GI Tee 25 mm dia

Supply only GI Tee 20 mm dia

Supply only GI Nipple 40mm dia 6 inch long

Supply only GI Nipple 25 mm dia 4 inch long

Supply only GI Nipple 20 mm dia 4 inch long

Supply only GI reducer 25/20 mm dia

Supply only GI reducer 20/15 mm dia

Labour for repair/rectification of leakage of underground CI/DI pipe line of size 80 to 150 mm bore dia in position complete with excavation Appx 1.0X1.0X1.0 mtr around the leakage, returning filling in,removal,cutting/dismentaling of leakage complete with and including cocking to existing lead joint,filling new lead joint burning and taking out existing lead joint as per site requirement and restore the water supply. Note: (Spare/fitting shall be measured and paid seperatly)

Supply and fixing in replacement of UNSV bolt 16 mm dia X6'' long fully threaded with counted head nuts and washer heavy duty conforming to ISI for MS column pipe/CI flenged pipe all as specified and directed.

M&L for cleaning to over head RCC reservoir of any capacity internally at appx 40 feet high stagging by using water treatment chemical/bleaching powder/Sodium hypochloride chemical including cleaning internally entire wall surface, removing deposited particular,scrubing complete wall surface and applying coat treatment water chemical on complete wall and drain out the water after disconnecting all rising/distrbution sluice valves complete with painting to MS/Steel railing/rising/distrbution/wash out CI pipe with different colour all as specified and directed and writting date of tank cleaning.

M&L for rectification of leakage in distrbution CI pipe line 150 mm bore dia of RCC Over head reservoir Appx at 40' to 60' height outside the reservoir near doom complete with replacement/cocking of lead,spun yarn,rubber gaskets,nut,bolt,washers of suitable size and made the pipe line leakage free all as specified and directed. Note:(i) Rates are deem to be included charges of hiring T&P,Veh,Ladders,steel shuttering or any equipment required at site. (ii) Contractor shall be fully responsible for life insurance of the person deployed at site and get the repair under his supervision visitor from the qualified technician.

Laabour for cleaning/removing deposited muddy soil from the internal surface area of shaft mounted RCC overhead resrvoir of capacity and made the internal area smooth and clean till the PCC base not achieved and deposited the muddy soil outside the installation not less than 50 mtr all as specified and directed by Engr-in-Charge.

Material and labour for replacement of for filling CI spigot and socketed Joint of any size Lead pig

Material and labour for replacement of for filling CI spigot and socketed Joint of any size Lead wool

Material and labour for replacement of for filling CI spigot and socketed Joint of any size Spun Yarn

Supply only Altoch packing of 45 Kg

S&F in replacement suction sweeper head for swimming pool (pool cleaner) 36 inch long complete with wheels,PVC core nylon brush 36 inch NRV complete all as specified and all as directed

S&F in replacement suction flexible rubber hose pipe 80 mm dia braded type green colour conforming to ISI complete with suitable size MS clamp

Repair/Maint/service to swimming pool filteration plant complete with replacement of UNSV Spare parts fitting valves,filter media,PVC strainer,Pressure gauge,Butter fly valve,air vent pipe complete with cleaning internally including taking out all filter media outside and kept sepratly each media at site for reuse ,preparing external services of filter media and make the serface smooth and apllying two coat of synthetic enamel paint and a coat of red oxide compete with suction and discharge pipe and relying all filter media in proper layer duly washed and tested on full load. Note:Spare shall be measured and paid sepratly

Supply only water pressure gauge 10 KG 100 mm dia complete with 3/8 inch brass sampling cock

Supply only butter fly valve cast iron body with gun metal sheet conforming to IS13095 of size 150 mm dia

M & L for replacement of gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 20 mm bore

Supply only double deck type PP strainer of size 3/8 inch or 1/2 inch

Repair/Maint/service to swimming pool dewatering centifugal pump set single stage 7.5 HP complete with replacement of CI impeller,neck ring,bearing,hosing,sleev and remetalling to pump shaft,wlding,brazing and polishing etc and make the pump serviceable.Note:Spare shall be measured and paid sepratly

Supply only CI Impeller

Supply only ball bearing

Supply only stainless steel sleeve

Supply only stainless steel neck ring

Supply only pump shaft coupling with key tyre type

Supply only superior quality copper sulphate all as specified and directed by Engr-in-Charge.

Suface exc. n exd. 30 cm deep and averaging 50 cm deep and getting out in soft/loose soil including taking out vagetation from entire area of water supply installation all as specified and directed by Engr-in-Charge.

M&L for cement concrete in foundation subways type D2 1:4:8 aggregate including demolising existing all as specified and directed by Engr-in-Charge.

M&L for PCC type B1,1:2:4 (20 mm graded stone aggregate) for subways 40 mm thick including demolising existing all as specified and directed by Engr-in-Charge.

Supply and fix in replacement PVC insulation patch roll for submersible cable conection all as specified and directed by Engr-in-Charge.

Sarbat Construction Co

Vishesh Engineers

M/S S K Electricals Regd

Bidder Name

Vishesh Engineers

M/S S K Electricals Regd

Sarbat Construction Co

Hi Tech Engineers