ADDN ALTN TO CERTAIN SMQS OMQS MES QTRS PHASE II AT AIR FORCE STATION HASIMARA

Amount

Demolition of Brick work or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and removing the debris and rubbish to a distance not exceeding 100 m, complete all as specified and directed. (Note : reinforcement cut as required to facilitate demolitions)

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness, (Below or above ground level) and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100 m, complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

Dismantling framed timber scantlings 40 sq. cm and over in section, in any position, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded and pointed in cement mortar, complete all as specified and directed.

Taking down chowkats or frame, n.exc 1.5 Sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frame,exc 1.5 Sqm but not exc 4.00 sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed.

Taking down shutter of any description exc 1 sq. m and n exc 2 sq. m each complete all as specified and directed.

Taking down shutter of any description exc 1 sq. m and n exc 2 sq. m each and refixing in same opening, complete all as specified and directed.

Taking up or down GI tubing of 15mm bore and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

Taking up or down GI tubing of 20mm bore and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for and removing from site of work complete all as specified and directed

M&L Brickwork with sub class 'B' bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6, complete all as specified and directed.

M & L for brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

All as per item No 20 above but except sheets , fixed with self tapping screws complete all as specified and directed. (Note : Serviceable roof sheets obtained from Srl item No 7.00 shall be re-used)

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutters/roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L for GI snap grid frame work for false ceiling of suitable size panel with hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete as per manufacturer's instructions including fixing of nut, bolt and clamps with the help of drilling machine complete all as specified and as directed

M&L for non asbestos, Fibre cement reinforced board high pressure steam cured (Design-Oceanic or as approved), pre painted self finished white/ivory colour , 4mm thick size (595mm x 595 mm ) board fixed or laid /inserted to GI framework with screws if required all as per manufacturer's instructions complete all as specified and directed.

M&L for rendering 15mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement, complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar (1:4) in two layers (10 mm thick in first layer and 5 mm thick in second layer) finished even and smooth (without using extra lime or cement) mixed with water proofing compound as per manufacturer’s instruction on top/second layer of plaster, complete all as specified and directed. (Note : WPC shall be measured & paid separately).

M&L for rendering 5mm thick in cement mortar 1:3 on ceiling and soffits of staircase, waist slab or concrete surface finished even and smooth without using extra cement, complete all as specified and directed.

Supply only integral water proofing compound approved quality, complete all as specified and directed.

M&L for 20-25 mm thick machine cut Kota Stone slab as in floors, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete , over and including 20mm thick screed bed of cement mortar 1:6 , complete all as specified and directed.

M&L for 20-25 mm thick machine cut Kota Stone slab as in skirting/dado/riser of steps, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete , over and including 10mm thick screed bed of cement mortar 1:3 , complete all as specified and directed.

M & L for 75mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base flooring including formwork, if required,complete all as specified and directed.

M & L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in sub base flooring including formwork, if required, complete all as specified and directed.

M & L for 25mm thick PCC 1:2:4 type B-0 using 12.50mm graded stone aggregate as in levelling course to floor finishes/sunken floor portion complete all as specified and directed.

M&L for coloured non skid ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.18 Sqm but n.exc 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:6, complete all as specified and directed.

M&L for coloured non skid ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.18 Sqm but n.exc 0.38 Sqm,as in skirting, dado, riser to steps etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4, complete all as specified and directed.

M&L for coloured non skid ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 Sqm but n.exc 0.18 Sqm, in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:6, complete all as specified and directed.

M&L for coloured non skid ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 Sqm but n.exc 0.18 Sqm,as in skirting, dado, riser to steps etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4, complete all as specified and directed.

M&L for cement concrete tiles of size 25cm x 25cm x 22mm thick, machine pressed, with grey cement and pigment, in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:6, complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size 350x250x7mm/450x350x7mm to 8mm thick in vertical surface set and jointed in neat cement slurry pointed with white or coloured cement to match over and including 10mm thick rendering in cement plaster 1:4, complete all as specified and directed.

M&L for 14-16 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete over and including 20mm thick screed bed in cement mortar 1:4, complete all as specified and directed.

M&L for 18-20 mm thick makrana white marble work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble complete over and including 20mm thick screed bed in cement mortar 1:4, complete all as specified and directed.

M & L for 40mm thick PCC (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in floor in alternate bays and finished the surface even and smooth using extra cement complete all as specified and directed. (Note : Glass dividing strips shall be measured and paid under respective item)

Supply only 38mm in width glass dividing strips, 3mm thick inserted in position complete all as specified and as directed.

M & L for sand cushioning as in bedding for laying of tiles complete all as specified and as directed.

M & L for 60mm thick Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 , M-35 Grade, paver block coloured with grey cement and pigment laid over sand cushioning all as specified and directed. (Note : sand cushioning shall be measured and paid under respective item)

M & L for 75mm thick PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection laid in alternate bays not exc 2 Sqm each and finished the surface fair and even without using extra cement , providing joints though out the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

M & L for Plain Cement concrete 1:3:6 , type C -1 (using 20 mm graded crushed stone aggregate) in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified and as directed. (Note : Inner girth only be measured)

M & L for PCC (1:2:4) , type B-1 (using 20 mm graded crushed stone aggregate) in in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including formwork if required , complete all as specified and as directed

M & L for PCC (1:3:6) , type C-1 (using 20 mm graded crushed stone aggregate) in in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including formwork if required , complete all as specified and as directed

M&L Reinforced cement concrete M 25 (Design Mix) using 20mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. (Note : Reinforcement and form work will be measured and paid separately under relevant items)

M&L Reinforced cement concrete M 25 (Design Mix) using 20mm graded aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span and the like complete all as specified and directed. (Note : Reinforcement and form work will be measured and paid separately under relevant items)

M&L Reinforced cement concrete M 25 (Design Mix) using 20mm graded aggregate in Chajjas and the like complete all as specified and directed. (Note : Reinforcement and form work will be measured and paid separately under relevant items)

M & L for steel formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc (fair finished flat surfaces) complete all as specified and directed.

M & L for steel form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for flat surface (Fair finished surfaces ) complete all as specified and directed.

M & L for steel form work to chullah hoods, chajjas, troughs including edges and similar work; for flat surface (Fair finished surfaces ) complete all as specified and directed.

S & F TMT steel bars 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

S & F TMT steel bars 6 to 8 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

S & F Mild steel TMT bars 5mm dia and over upto and including 10mm dia in strirrups, spacers and binders spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed.

M & L for brushing neat cement slurry with 3.0kg of cement per sq. metre on concrete surfaces complete all as specified and as directed.

M & L for cleaning the surfaces of brick masonary/RCC surfaces by using wire brush, brooming down and washing with water to remove dust, dirt etc and brushing with neat cement slurry @0.50 Kg/Sqm with acrylic based polymer modified cementitious composite (Pidifine 2K) @ 0.50 Kg/sqm as per maufacturer's instructions complete all as specified and as directed.

M & L for rendering 10mm thick in cement mortar 1:3 on fair faces of brick work or concrete surfaces of sunken portion, finished even and smooth (without using extra lime or cement) mixed with water proofing compound as per manufacturer’s instructions complete all as specified and directed. (Note : WPC will be measured & paid separately).

M & L for PCC ( 1:5:10 ), type E-2 (using 40 mm graded crushed stone aggregate) as in sunken portion , filling and mass concrete etc, complete all as specified and as directed

Taking down/dismantling existing unserviceable cement plaster/loose and unsound cement concrete of any description and in any position from RCC roof slab/beams/columns depth varying from 25 mm to 90 mm with power driven or pneumatic chisel including saw cutting of all edges making square shoulders of the cavities, roughening of smooth surfaces scraping out/removing corrosion/all loose scales/rust etc all as specified and directed.

Removal of rust from reinforcement completely by rubbing with wire brush/emery paper and proper cleaning of reinforcement with RUSTKLENE or Sika rust off-100 (Rust converter manufactured by Sika India Pvt. Ltd.) or MC Bauchemie India Pvt Ltd or Fosroc Industries Banglore or equivalent as per manufacturer's instructions all as specified and as directed.

S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS.1161- 1979 grade St.-240 complete all as specified and as directed.

S & F 105 x 60mm size pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

S & F 125 x 60mm size pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

S & F well seasoned 2nd class hard wood plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S & F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, conforming to Fe 410 W Gde E-250 quality A complete all as specified and as directed.

S & F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, edges will be painted to match with printed sheet, all as per specification & drawing complete and as directed.

S & F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, all as per specification & drawing complete and as directed.

S & F for 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S & F 35 mm thick, factory made, Second class hardwood, glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc, divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, etc complete all as specified and directed in SSR Part I Section 8 clause 8.24 (b).

S & F Factory Made Solid PVC Moulded Door Shutter, with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and both side Prelam PVC sheet used,. Stile and rails feathered at edges prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of pre laminated PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing, complete all as directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing, complete all as directed.

All as per item No. 77 above but wire gauged shutter, i.e. panel will be of wire gauged in lieu of PVC sheet panel. The wire gauge shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly, complete all as specified and as directed.

S & F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

S & F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, complete all as specified and directed.

S & F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

Taking down old serviceable steel window shutter from the frame and refixing the same after repairing, cutting/welding/grinding etc, removing rust by using wire brush/emery paper/grinding etc, if required, including welding of 02 Nos of box hinges

M & L for mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M & L for mild steel framed work such as hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M & L mild steel Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S & F 2nd Class Hard wood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each complete all as specified and directed.

S & F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

S & F 'in repair' stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

S & F for 3 mm thick, plain sheet glass, ordinary quality and glazing with oil putty or wooden beading in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F ' in repair ' 3 mm thick, plain sheet glass, ordinary quality and glazing with oil putty or wooden beading in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F 3 mm thick, figured sheet glass, pin head type and glazing with oil putty or wooden beading in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F 75mm size, Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S & F 100mm size, Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S & F 150 mm size, Aluminium handles, cast type, anodised complete all as specified and directed.

S & F 150 mm long, Aluminium anodised, barrel tower bolts of extruded section fixed, complete all as specified and directed.

S & F 300 mm long, Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

S & F ' in repair ' 300mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate complete, all as specified and directed.

M & L for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and directed.

M & L for preparation of new or previously untreated steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M & L for preparation of old painted steel or iron surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparation of old painted steel or iron surfaces of any description over 10cm width or girth and applying one coat of aluminium paint (Ist grade quality) complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, of any description, new or old, treating small articles such as stop, covers, gully grating, holdfasts, ends of posts, backs of chowkats etc, area n exc 0.1sqm each and treated with tar or coal tar black paint, complete all as specified and as directed.

M & L for preparation of old plastered surfaces of wall and applying two coats of acrylic distemper (Ist quality) of approved manufacturer having VOC content less than 50 gms/litre, of required shade and colour as per manufacturer's specifications over a coat of primer paint, over and including 1.5mm thick acrylic wall care putty , after complete removal of existing treatment from walls, complete all as specified and directed.

M & L for preparation of newly plastered surfaces of wall and applying two coats of acrylic distemper (Ist quality) of approved manufacturer having VOC content less than 50 gms/litre, of required shade and colour as per manufacturer's specifications over a coat of primer paint, over and including 1.5mm thick acrylic wall care putty ,complete all as specified and directed.

M & L for preparation of old plastered surfaces of wall by washing, rubbing down and stopping of distempered and painted surfaces and applying two coats of old bound distemper over chalk whiting preparatory to distempering ,complete all as specified and directed.

M & L for preparation of newly plastered surfaces of wall and applying three coats of white wash,complete all as specified and directed.

M & L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash,complete all as specified and directed.

M & L for preparation of newly plastered surfaces of wall and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed.

M & L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of primer , complete all as specified and directed.

M & L for preparation of old plastered surfaces of wall and applying two coats of cement base paint, complete all as specified and directed.

M & L for preparation of old plastered surfaces of wall and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm, complete all as specified and directed.

M & L for preparation of old plastered surfaces of wall by scrubbing down with steel wire brush, scrapping down, smoke soot, moulds, moss, salts,trading oil and greasing spots and applying two coats of white wash, complete all as specified and directed.

M & L for preparation of old plastered ceiling surfaces by scrubbing down with steel wire brush, scrapping down, smoke soot, moulds, moss, salts,trading oil and greasing spots and applying two coats of white wash, complete all as specified and directed.

M & L for obliterating old writing of any description, n exc 0.1 sq. m, with paint to match existing work , complete all as specified and as directed.

Writing letters or figures (Block. Roman, Italic or Indian) n exc. 30 cm high with synthetic enamel paint, complete all as specified and directed.

Roughening surface of old concrete roof by picking, sweeping clean and washing down with water using wire brush brooming down and applying the following treatment all as directed in order of precedence as stated :- (i) Rendering 15mm thick in CM (1:4) on existing roof surface true to level. ii) Applying one coat of bituminous primer @ 0.40 Ltr/Sqm. (iii) Supply and laying 3mm thick APP based polymeric membrane of approved manufactured with weight not less than 3.60 Kgs per Sqm reinforced with non-woven polyester fabric/matt weighing not less than 160gms per Sqm having softening point not less than 150 mm centigrade, having tensile strength of 650 N/5cm and 350 N/5cm in longitudinal and transverse directions respectively of the reinfocred tearing strength of 180 N by torch application . Polymeric membrane shall be taken to a height of 30cm(minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. Note :- (i) Laying APP based polymeric membrane shall be done torch on method as per manufactures instructions. (ii) A minimum overlap of 100mm and 75mm should be made at the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as per manufacturers instruction. iii) APP based polymeric membrane shall be of any one of the approved makes as specified here-in-after and shall conform to specifications given in IS 16540-2017/IS 16532-2017.

Item No 118 Contd..... (iv) Applying one coat of aluminium paint @0.11 Kg/Sqm over APP membrane surface (v) Contractor shall produce necessary test certificate of the manufacturer to the Engr-in-Chage before incorporation in the work. (vi) Necessary independent tests shall also be carried out by the Contractor without any extra cost to the Deptt as per relevant IS specifications and membranes with satisfactory test results shall only be incorporated in the work (vii) The work shall be executed through authorised applicators of original manufacturer only

M & L for cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3, complete all as specified and directed.

Disconnecting existing tanks, setting asside (or lowering if required) for repairs of roof, cleaning etc and hoisting if required reconnecting and re-fixing in position , exc. 250 ltrs and n. exc. 500 ltrs capacity , complete all as specified and directed

Cleaning and removing all scale and dirt, etc, from tanks of capacity 500 ltrs and from mouths of circulating pipes, etc.complete all as specified and directed

S & F 500 litres capacity rotational moulded polyethylene (HDPE) water storage tanks (Cylindrical vertical with closed top), ISI Marked, conforming to IS 12701-1989 having triple layers wall construction with manhole threaded lid and suitable locking arrangement including making holes for inlet, outlet and over flow pipes,hoisted and fixed in position complete all as specified and directed.

S & F 1000 litres capacity rotational moulded polyethylene (HDPE) water storage tanks (Cylindrical vertical with closed top), ISI Marked, conforming to IS 12701-1989 having triple layers wall construction with manhole threaded lid and suitable locking arrangement including making holes for inlet, outlet and over flow pipes,hoisted and fixed in position complete all as specified and directed.

S & F for 20mm dia PTMT Nipple suitable for HDPE water tank. (Minimum weight 15 mm-38gms/20mm- 45gms /25mm- 65gms) complete all as specified and as directed.

S&F 20mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm- 42gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

S&F 'in repair' 20mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm- 42gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

S&F ' in repair' 20mm bore dia gun-metal. Globe or gate valves with iron wheel head screwed both ends for iron pipes complete all as specified and directed.

S&F 'in repair' water tank cover suitable for any type of rotational moulded polyethylene water storage tanks , complete all as specified and directed.

S&F GI tubing of 15mm dia medium grade with all fitting and fixed complete to walIs and ceilings or laid in floors complete all as specified and directed.

S&F GI tubing of 20mm dia medium grade with all fitting and fixed complete to walIs and ceilings or laid in floors complete all as specified and directed.

S&F GI tubing of 15mm dia medium grade with all fitting and fixed including cutting chases for concealed water tubing etc. and making good, cutting not exc 10 cm girth fixed to wall/ceiling or laid in floors, making good surfaces with cement mortar 1:3, complete all as specified and directed.

Lagging to 15mm dia steel water tubing pipes used in internal water supply or plumbing all round with, 25min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9842, complete all as specified and directed.

Refixing 15mm old steel tubing obtained from Srl Item No 15 here in before with all connections ,i.e, tees, bend, elbow, union,sockets etc in new or old position (Walls, ceiling, floors, etc.)complete all as specified and directed. (Note : Rate shall be inclusive of all new connections/fittings required)

Refixing 20mm old steel tubing obtained from Srl Item No 16 here in before with connections ,i.e, tees, bend, elbow, union,sockets etc in new or old position (Walls, ceiling, floors, etc.) complete all as specified and directed. (Note : Rate shall be inclusive of all new connections/fittings required)

S&F ' in repairs' 15mm bore fancy type chromium plated, concealed stop valves ,cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 'in repair' 15mm bore fancy type chromium plated angular stop cock , screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 'in repair' 15mm bore fancy type chromium plated, two way angular stop cock , screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 'in repairs ' for 15mm bore , fancy type chromium plated bib tap, cast copper alloy with capstan head long body and cup, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F 'in repairs ' for 15mm bore , long body ,fancy type, chromium plated bib tap, cast copper alloy with capstan head long body and cup, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F 'in repair' 15mm bore bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm 125gms).complete all as pecified and directed.

S & F ' in repairs ' 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends complete all as specified and directed.

S & F 'in repair' 32 mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F 32mm dia PVC waste pipe for WHB fixed with one end with socket complete all as specified and directed.

S&F 40mm dia PVC waste pipe for kitchen sink/urinal fixed with one end with socket complete all as specified and directed.

S&F 'in repairs ' pillar taps,15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed fency type complete all as specified and directed.

S&F 'in repair' 3 in-1 brass chromium plated fancy type wall mixer, 15mm bore for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F 'in repair' brass chromium plated fancy type centre hole mixer, 15mm bore for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F 'in repair' brass chromium plated fancy type swan neck sink mixer regular spout T/M, 15mm bore for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F ' in repairs' 20mm dia , brass chormium plated towel rail D type, 60cm long between flanges, fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms) complete all as specified and directed.

S&F 'in repairs' Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and directed.

S&F ' in repair ' CP health faucet along with 1m long flexible tube and holding stand incl all necessary fitting complete all as specified and as directed

S&F ' in repair ' 125mm size chromium plated shower roses with arm , with or without swivel joints, any size, including fixing to steel pipe or union, complete, all as specified and as directed.

S & F 'in repairs '10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

Fixing only in repairs high or low level fluslhing cistern (exclusive of brackets), and connections to pipes and fixing of chain and pull, or lever, if any complete all as specified and directed.

S&F ' in repair ' chromium plated brass soap dish , any type , fixed to plugs with chromium plated brass screws, complete all as specified and as directed. ( Make :Prayag Cat part No BA-05 or equivalent )

S&F ' in repair ' sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed.

S&F ' in repair ' chromium plated brass toilet paper holder with cover plate, box type fixed to walls with chromium plated (CP) brass screws, complete all as specified and as directed. ( Make :Prayag Cat part No BA-08 or equivalent ).

S&F ' in repair ' sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm ,incl 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM (1:3) if required, complete all as specified and as directed.

S & F ' in repairs' Vitreous China wash basin, white, flat back, size 550 x 400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

Fixing only ' in repairs' Vitreous China wash basin, (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

S & F ' in repairs' vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe), including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor, complete all as specified and directed.

S & F ' in repairs ' vitreous China wash down water closet pan (pedestal pattern), white, ' P ' or 'S ' trap ,including connection to outgoing drain and flushing pipe, anti syphonic pipe with and including water closet seat cover complete but excluding flushing cistern & flush pipe including making good damaged/disturbed surfaces complete all as specified and directed.

S&F for 25mm thick wooden grain PVC celuka ply fixed in shelves; Partitions and shelves of built-in cupboards, almirahs, book cases, toilet boxes, racks, pelmets and similar work fixed with screws/self tapping screws etc, fixed in repair complete all as specified and directed

S&F for 18mm thick wooden grain PVC celuka ply fixed in shelves; Partitions and shelves of built-in cupboards, almirahs, book cases, toilet boxes, racks, pelmets and similar work fixed with screws/self tapping screws etc, fixed in repair complete all as specified and directed.

S & F for Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed, complete all as specified and directed.

S & F for 75mm size hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws,complete all as specified and directed.

S&F perforated Cutlery Drawer Length 500-550 mm, Depth- exc 490 mm , Height -90 mm made of stainless steel of Grade IS:202.including good quality telescopic channel set for movement ,if required, including necessary fixing arrangement to the kitchen cabinet/cupboard board with glue/nails/screw etc all as specified and directed.

S&F Plain basket Drawer Length 500-550 mm, Depth- exc 500 mm , Height -100 mm made of stainless steel of Grade IS:202. ( allowable tolerance limit 20mm in dimension ) including good quality telescopic channel set for movement,if required, including necessary fixing arrangement to the kitchen cabinet/cupboard board with glue/nails/screw etc all as specified and directed.

S&F Cup and saucer basket length 500-550 mm, Depth- exc 500 mm , Height -100 mm made of stainless steel of Grade IS:202. ( allowable tolerance limit 20mm in dimension ) including good quality telescopic channel set for movement,if required, including necessary fixing arrangement to the kitchen cabinet/cupboard board with glue/nails/screw etc all as specified and directed.

S&F Thali basket Drawer Length 500-550 mm, Depth- exc 500 mm , Height -200 mm made of stainless steel of Grade IS:202. ( allowable tolerance limit 20mm in dimension ) including good quality telescopic channel set for movement,if required, including necessary fixing arrangement to the kitchen cabinet/cupboard board with glue/nails/screw etc all as specified and directed.

S&F in repair of D-tray dia of tray 750 mm dia made of stainless steel of Grade IS:202. ( allowable tolerance limit 20mm in dimension ) including good quality telescopic channel set for movement,if required, including necessary fixing arrangement to the kitchen cabinet/cupboard board with glue/nails/screw etc all as specified and directed.

S&F 35mm hinge with self-closing cup CC 48mm, clip on, 4 hole plate, hinge with arm cover for kitchen cabinet/cup board etc complete all as specified and as directed.

S & F 125mm long stainless steel mirror finish modular kitchen cabinet handle complete all as specified and as directed.

S & F 150mm long stainless steel mirror finish modular kitchen cabinet handle complete all as specified and as directed.

S & F 500mm long stainless steel utensil rail wall mount, kitchen rail with 6 Nos kitchen sliding hooks for hanging kitchen tools/spatula etc complete all as specified and as directed.

S & F for brass knobs 35-40mm dia complete all as specified and as directed.

S & F 30mm Width of flaps (when open) Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, complete all as specified and as directed.

M & L for 4mm thick glass for shelves/shutter for cabinet (not exc 0.50 sqm ) including grinding, nosing/rounding off edges of glass , polishing if required , complete all as specified and as directed.

M&L for 'Push to open' opening system for handle less furniture' and necessary magnetic door closer for glass shutter of cupboard,complete all as specified and as directed.

S&F stainless steel plate rack of size 0.75 x 0.78m standard quality, weight not less than 6 kg/each fixed with brass screws complete all as specified and as directed.

S&F 20 mm dia curtain rod mild steel chromium plated decorative type complete all as specified and as directed.

S&F decorative type brackets with ends/stops etc including other accessories for fixing arrangements of 20 mm dia curtain rod to wall ,complete all as specified and as directed.

S&F 150mm (Overall length of cover plate) floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and as directed.

Demolition and breaking up drain pipes 100/75mm bore (Salt glazed ware, AC or Reinforced concrete) set in cement mortar ,complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including stack clamp of MS flat iron of size (40 x 4mm ) ,complete all as specified and as directed.

Fixing only 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including stack clamp of MS flat iron of size (40 x 4mm ) ,complete all as specified and as directed. (Note : serviceable pipes obtained Srl item No 189 shall be re used)

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including stack clamp of MS flat iron of size (40 x 4mm ) ,complete all as specified and as directed.

S&F 'in repair' 110mm bore, PVC (SWR) bends of any radious , complete all as specified and as directed.

S&F 'in repair' 110mm bore, PVC (SWR) junction single, (single T) equal or unequal , complete all as specified and as directed.

S&F 'in repair' 75mm bore, PVC (SWR) bends of any radious provided with access door, complete all as specified and as directed.

S&F 'in repair' 75mm bore, PVC (SWR) junction single, (single T) equal or unequal , complete all as specified and as directed.

S&F 'in repair' 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and as directed.

S&F 'in repair' 100mm dia Chomium plated grating with or without waste hole, fixed to floor trap, complete all as specified and as directed.

Demolition and breaking up drain pipes 150mm bore (Salt glazed ware, AC or Reinforced concrete) set in cement mortar, complete all as specified and as directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, for lying of cable etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

M & L for PCC ( 1:4:8 ), type D-2 (using 40 mm graded crushed stone aggregate) in foundations, filling and mass concrete etc, including formwork, if required, complete all as specified and as directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and as directed.

Removing excavated material(Soils) to a distance n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed

M & L for concrete bed in cement concrete 1:4:8 type D 2 to drain pipes 150mm bore including packing under, and haunching against the sides of pipes after they are laid and tested , complete all as specified and directed

M & L for 150mm bore salt glazed stoneware drain pipes laid in trenches and jointed as specified, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering , cutting out existing benching for and forming branch channel(1/2 round or 3/4 section) in cement concrete 1:2:4 type B 1 smooth finished and reforming benching for 100mm internal dia of pipe as required complete all as specified and as directed.

M & L for providing precast cement concrete louvres and jallies 25mm thick (measured solid), type C-0, 1:3:6(using 12.5mm graded stone aggregate) , including all mould- ings but excluding frame set in cement mortar 1:4, complete all as specified and directed.

Taking down steel rolling shutters of any description and refixing the same after carying out repairs, oiling and greasing including replacing with new guide channels if required,and weldings etc. complete and providing one coat of synthetic enamel paint to match with existing surface area of each shutter n. exc 7 sqm complete all as specified and directed. [Note: Supply of spare parts like bearing, tension spring/ gear operated lever, shaft, guided rail/channel shall be measured and paid separately]

Supply only ball bearing for rolling shutter suitable for 32 to 40 mm suspension shaft complete all as specified and directed.

Supply only tension springs of rolling shutters suitable for 32 to 40 mm suspension shaft complete all as specified and directed.

Supply only mild steel pipe heavy duty 40 mm dia suitable for shaft of rolling shutters including dismantling the old rusted /broken shaft and positioning with all accessories complete all as specified and directed.

S & F safety lever locks mild steel with 4 levers for rolling shutterscomplete all as specified and directed.

S & F 1mm thick Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, push pull or manual type, complete all as specified and directed.

E/M PORTION (INTERNAL ELECTRIFICATION) Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Taking down fan any type , sealing cable end, dismantling blades and removing fan and blades to store complete all as directed

Taking down carefully by unscrewing from boards/ outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc. for reuse at site or carrying to the store, complete all as directed

Taking down unserviceable/BER geyser of any capacity from existing location /site and depositing MES store yard complete all as directed

M & L for point wiring for One light point / one fan point controlled by one, one way switch complete as specified with 1100 V grade with 1.5 Sqmm single core PVC insulated unsheathed FR-LSH cable, copper conductor multistranded passing through including PVC concealed conduit(medium grade) concealed on wall/floor and surface type on ceiling of size not less than 20mm dia with and its accessories with sunk cast iron/pressed steel terminal boxes of standard , suitable size having 1.6mm thickness, one light or one fan point controlled by one switch incl 1.5 sqmm (nominal area) copper conductor cable (multistranded), FRLSH type, PVC insulated and unsheathed with colour code earth wire of 1.5 sqmm multistranded properly connected connected to common earth dolly at one end and metallic bodies of luminaries /fan at other end complete allas specified complete all as specified and directed for the following :- Note :- (i) Rate quoted shall include for cost of making concealed cast iron box/pressed steel terminal box in stone/brick wall including cutting and sinking of boxes and making good to the stone/brick walls (No extra payment will be made for the same. (ii) Provision of blank plates as per site requirement (No extra payment will be made for the same)

All as per Srl item No. 216 here in before but for One 5 Amp 5 pin socket outlet point on same board complete.

All as per Srl item No. 216 here in before but on independent board complete.

All as per Srl item No. 216 herein before but with 4.0 Sqmm PVC copper stranded cable FRLSH type for one 15 Amp 6 pin socket outlet point including PVC cable 4.0 Sqmm FRLSH type copper stranded conductor as earth wire as specified & connected to commen earth & earth terminals including boards for mounting purposes complete.

All as per ser item No. 216 here in before but one light point controlled by 2 way switches.

All as per Srl item No. 216 here in before but one bell/buzzer point controlled by one push button on the same board with other switches or independent complete.

S & F switch piano flush button 5 Amp single pole one way 230 volts white finish all as specified & directed.

S & F Bell push, flush type, 5 amp, 230 volts white finished all as specified and directed.

S & F socket outlet flush type 2 in 1,3 pin 5 Amp 230 volts, white/ivory finished all as specified & directed.

S& F 15/16 Amp switch flush type 230 volts single pole white/ivory finished all as specified & directed.

S & F socket multipurpose flush type 2 in 1 type (3 and 3 pin ) 5/16 Amps, 230V, AC white / ivory finish all as specified and directed.

S & F switch piano flush button 5 Amp single pole 2 way 230 volts white finished all as specified & directed.

M & L for point wiring for One light point / one fan point controlled by 5A one, one way 1 Module switch complete as specified with 1100 V grade with 1.5 Sqmm single core PVC insulated unsheathed FR-LSH cable, copper conductor multistranded passing through including concealed PVC conduit not less than 20mm dia with concealed modular box suitable for modular switches, sockets etc and modular white plates of suitable size as required at site with PVC insulated FRLSH unsheathed stranded copper conductorof size 1.5 sqmm as earth wire connected to common earth dolly as specified complete all as specified and directed for the following :- Note :- (i) Rate quoted shall include for cost of making MS sunken box concealed in stone/brick wall including cutting and sinking of boxes and making good to the stone/brick walls (No extra payment will be made for the same). (ii) Provision of blank plates, modular white plates, frame and sorroundings shall be included in quoted rate , as per site requirement (No extra payment will be made for the same)

All as per Srl item No. 228 here in before but for One 5 Amp switch socket on same board complete.

All as per Srl item No. 228 here in before but for 5 Amp switch socket on independent board complete.

All as per Srl item No. 228 herein before but with 4.0 Sqmm PVC copper stranded cable FRLSH type for one 15 Amp switch socket outlet point including PVC cable 4.0 Sqmm FRLSH type copper stranded conductor as earth wire as specified complete

All as per ser item No. 228 here in before but for 2 way point wiring using 1.5 sqmm cable as main conductor and earth conduction complete.

All as per Srl item No. 228 here in before but one bell/buzzer point controlled by one push button on the same board with other switches or independent complete.

S & F Switch modular type, single pole, one way, 5/6 Amp, one module, IS:3854 marked with valid CML No complete all as specified and directed.

S & F Switch modular type, single pole, one way, and 15/16 Amps, one module IS:3854 marked with valid CML No complete all as specified.

S & F socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, two module, modular type IS-1988 marked with valid CML No complete all as specified and directed.

S& F socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin 5/6 Amp, modular type IS-1988 marked with valid CML No complete all as specified and directed.

S & F bell push, modular type, single pole, 5/6 Amp, one way, one module,IS:3854 marked with valid CML No complete all as specified and directed.

S & F in replacement of bell, ding dong type AC, 230 volts, single phase complete all as specified and directed.

S & F ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Energy efficient, five star rated, with brushless direct current motor (BLDC) complete with mounting arrangment as per site requirement and connecting wire up to nearest ceiling rose in flexible PVC pipe complete all as specified and directed.

S & F energy efficient exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete with mounting arrangment as per site requirement and connecting wire up to nearest ceiling rose in flexible PVC pipe complete all as specified and directed.

S & F in replacement of stepped type electronic fan regulator flush type complete all as specified and directed.

S & F fan step Regulator modular type, two module, IS:3854 marked with valid CML No complete all as specified and directed.

S&F ceiling rose of size 65 x 50 mm surface bakelite 240 Volts three terminal complete all as specified and directed.

S&F lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F LED Lamp 07 Watt, B22 base complete all as specified and directed.

S & F LED tube 20 W Tube light fitting inverter LED Batten with square profile and polycarbonate channel a lithium Iron Battery connecting up with three core flexible copper conductor cable of suitable size from ceiling rose upto 1.5m length, complete all as specified and directed.

S&F LED tube 10 W Tube light fitting Decorative ultra slim square profile LED lighting fixture with extruded ploycarbonate, environmental friendly, energy efficient ready to use pack connecting up with three core flexible copper conductor cable of suitable size from ceiling rose up to 1.5m length, complete all as specified and directed.

S&F LED bulkhead lights fitting 10 W , 220V, AC decorative wall mounted type brushed nickel finish fixture with acrylic with 10 W LED Lamp B22 base with driver, holder including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose up to 1.5m length, complete all as specified and directed.

S&F electric water heater storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated with LED lamp holder complete with all accessories such as safety valve, thermostat, NRV, including PVC connection pipe for cold water and FRP reinforced metallic braided connection pipe for hot water to existing water lines,necessary fixing arrangement by using 50 X 5 mm MS plate and writing MES No and paste the instruction sheet of Do’s and DO NOT complete all as specified and as directed.

S&F MCB DB TPN 4 way,Triple pole and neutral, IP 43 protection ,double door , concealed on wall complete all as specified and as directed.

S&F MCB DB SPN double door 12 way with 100 amps rated bus bar ,Single pole & neutral, IP 43 protection concealed on wall, complete all as specified and as directed.

S&F MCB DB SPN double door 4 way with 100 amps rated bus bar ,Single pole & neutral, IP 43 protection concealed on wall, complete all as specified and as directed.

S & F of MCB 5 to 32 Amp , 10 KA breaking capacity, 230 Volt etc complete all as specified and as directed.

S & F of MCB SPN 20 Amp with 10KA breaking capacity, B curve, 230 Volt complete all as specified and as directed.

S & F of MCB SPN 32 Amp with 10KA breaking capacity, B curve, 230 Volt complete all as specified and as directed.

S & F of MCB TPN/FP 63 Amp with 10KA breaking capacity, B curve, 415 Volt complete all as specified and as directed.

S & F MCCB 4 pole 63 Amp 16 KA and adjustable type, complete all as specified and as directed.

S & F power unit upto 25 Amps modular type including socket 25 Amp, 04 module with concealed metal box for mounting of power unit, modular power socket 25 Amp complete all as specified and as directed.

M & L for sub main wiring with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLSH type, cables 6 Sqmm drawn through in and including rigid PVC heavy duty concealed conduits including 6 Sqmm 1100 Volts grade, FRLSH type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. Note :- (i) Three runs of cables will be measured as one length of sub main. (ii) PVC conduit and its accessories is deemed to be included in this item rates. (iii) Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc.

M & L for sub main wiring with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLSH type, cables 4.0 Sqmm drawn through in and including rigid PVC heavy duty concealed conduits including 4.0 Sqmm 1100 Volts grade, FRLSH type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. Note :- (i) Three runs of cables conduit will be measured as one length of sub main. (ii) PVC conduit and its accessories is deem to be included in this item rates. (iii) Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc.

M & L factory made powder coated indoor type MS box of size 900 x300 x 1500 mm ( Double Door) 2.0mm thickness , dust proof with front opening hinged door both side, made out of 2mm thick MS sheet cubical type for mounting of, electric meter etc inside the box fixed inside the wall after cutting of wall of suitable size in concealed and making good the surface with cement mortar/concrete, brick work and matching the surface with surface finishes etc including dismantling of MS box , electric meters and fixing the new electric meters in new box carefully including necessary electric connection by suitable size of copper conductor cable of suitable length and testing complete all as specified and directed. Note : (a) Any repair/making good work involved while taking out old unserviceable meter box and fixing the new meter box is deemed to be included in this item rate. (b) PVC flexible conduit required within the meter boxes is deemed to be included in this item rates. (c) Meter reading of electric meter shall be recorded properly before taking out from the existing position before dismantling meter box and same shall be fixed after installation of new meter box).

Material & Labour in replacement of Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6.3 mm thickness burried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to and incl galvanised earth lead wire of 4.00mm dia by means of nuts & bolts, check nuts and washers of galvanised incl PCC pit of 1:2:4 type B-1, cover reinforced with XPM weight not less than 4 Kg/Sqm and 6mm dia bar handle, earth pit angle iron frame of size 25mm x 25mm, excavation and earth work in any type of soil, charcoal dust, salt, light grade GI watering pipe 20mm dia with funnel and wire mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete all to as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected main switch board all as specified and testing on completion, including disposal of surplus soil to a distance not exceeding 50m , complete all as specified and as directed. [Note : (a) The unit rate includes for protection pipe and earth lead upto 7.5 m. Any variation in length of earth leas and protection pipe beyond 7.5 m shall be measured and paid seperately. (b) Excavation/earthwork is deemed to be included in the quoted rate.]

S&F LED street light of capacity 50 Watt IP 65 alognwith 40mm dia GI pipe , light grade of 1.2 mtr length ,fixing accessories such as GI bracket of suitable size bend at an angle to focus properly duly mounted on wall with clamps/nut/bolts washers etc complete all as specified and as directed.

S&F factory made factory assembled wall mounting oscillating fans 230V single phase 450mm sweep, complete all as specified and as directed..

E/M PORTION (EXTERNAL ELECTRIFICATION) Taking dowm LT UG cable of any type and size complete all as specified and as directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, for lying of cable etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed. Note : During execavation work, no mechanical excavator is permitted at site, mannual excavation only.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and as directed.

Removing excavated material(Soils) to a distance n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed

Supply & laying 40mm dia double walled corrugated (DWC) HDPE pipe of approved colour for cable protection with fittings,conforming to IS, complete all as specified and directed.

S&F GI tubing of 50mm dia light grade with all fitting and fixed complete to walIs and ceilings or laid in floors/under ground for protection of cable complete all as specified and directed.

M & L for boring of holes (horizontally) under road, pavement, hardstanding by manual method, below upto 0.6 mtr from road surface and dia of hole not exc 100mm without damaging the existing road , getting out and disposal of excavated soil to a distance not exc 50 mtr from the site of work complete all as specified and directed.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured electric power cable( heavy duty ) strandard aluminium conductor 1.1KV volt grade of size 25 sqmm, 4 core complete all as specified and directed.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured electric power cable( heavy duty ) strandard aluminium conductor 1.1KV volt grade of size 16 sqmm, 4 core complete all as specified and directed.

Sch 'A' Part-II (SCHEDULE OF CREDIT) Note :- Amount of Rs. 524475.00 indicated in Tender Documents as Schedule of Credit shall be deducted from the total quoted amount of BOQ.

M/S MANODEEP CONSTRUCTION

M/S AHUJA TRADING

M/S Sohanlal Agarwala

DEEP NIRMAN

Atish Builders LLP

B D Raizada Projects Pvt Ltd