SPECIAL REPAIR TO BLDG NO P 142 01 TO 04 JCOs MD ACCN AT RLT VIHAR UNDER GE NORTH AKHNOOR

Amount

Demolition of cement concrete (un-reinforced) of any position not otherwise specifically provided for complete all as specified and directed.

M&L for providing pre-cast RCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in cover (for manholes and drains) including necessary form work set in CM 1:4 with and including demolition of existing unserviceable cover complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately)

S&F mild steel TMT bars 8 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in coping, benching, weathering slightly rounded or chamferred angles and including necessary form work complete all as directed

Excavation in trenches not exceeding 1.5 meter wide and not exceeding 1.5 mtr deep and getting out complete in any type of soil complete all as specified and directed

S & F 100mm Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floor including demolition and breaking up of existing old drain pipe (salt glazed stone ware) set in cement mortar including demolition of concrete bed and haunching complete all as specified and directed by Engr-in-Charge.

Concrete bed in PCC 1:3:6 type-C-2 (using 40mm graded crushed stone aggregate) to drain pipe 100mm bore including packing under and haunching against the sides of pipes after they are laid and tested all as specified and directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25cm, complete all as specified & directed.

Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified & directed.

Taking down old treatment including padding, removing existing bitumen felt treatment including brushing, cleaning top surface of roof slab, brooming etc complete all as specified and directed.

Rendering 15 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces including finishing the surface fair and even of roof slab (without using extra cement) complete all as specified and as directed by Engineer-in-Charge.

Water proofing treatment to RCC roof slab including parapet as under :- (a) Ist Course : Apply a coat of bituminous primer conforming to IS-3384@ 0.40 Kg /Sqm on prepared surface of plaster and after drying of primer, apply a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.2 Kg/sqm on plastered surfaces. (b) 2nd Course : APP (Atactic Polypropylene) modified polymeric membrane, 5 layered, 3 mm thick weight not less than 4.0 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 150 mm end overlap, membrane has to be laid with LPG torch and overlap sealed and finished neat, all joints and changes in direction should be covered with cement mortar 1:3 mixed with SBR latex @200ml/bag of cement and curved before laying of membrane. (c) 3rd Course : Apply a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.2 Kg/sqm over membrance and dusted with dry sand @ 0.50 to 1 Kg/sqm dusted over bitumen coat.

Note : (i) Roof treatment work shall be carried out through approved manufacturers only. (ii) If Non-accesible roof : After providing (a) to (c) provide aluminium paint as per manufacturer instructions. (iii) Covered fillet in PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) of required radius shall be provided at the junction of roof and vertical surface such as parapet wall/mumty around opening and treatment mentioned above shall be applied followed by a cement plaster 20mm thick in cement mortar(1:6).

M&L for cement concrete tiles 25 cm x 25 cm x 22mm thick, machine pressed, set jointed and pointed in neat cement slurry in floors including 10mm thick screed bed in CM (1:6) complete all as specified and as directed by Engineer-in-Charge.

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Rendering 10 mm thick in cement and sand mortar 1:6 on other than fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth (without using extra cement) complete all as specified and as directed by Engineer-in-Charge.

Rendering 15 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth (without using extra cement) complete all as specified and as directed by Engineer-in-Charge.

Supply only integral water proofing compound

Providing and applying wall care putty of 3mm thickness over plastered surface of walls to prepare the surface even and smooth complete all as specified and as directed by Engineer-in-Charge.

Rendering 5mm thick in cement and sand mortar 1:3 on cement concrete surfaces of ceiling including finishing the surface even and smooth (without using extra cement) complete all as specified and as directed by Engineer-in-Charge.

M&L for Preparation of new treated surfaces of walls and applying two coats of distemper oil emulsion over one coat of primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of white wash complete all as specified and directed.

M&L for Preparation of new treated surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for Preparation complete removal of existing treatment of old treated surfaces of walls and applying two coats of cement base paint to walls including one coat of primer complete all as specified and directed.

Repair to balcony/Facia and soffit of chajjas etc by taking down old rendering 20 to 25mm thick to match with the existing thickness in CM 1:3 and hacking clearly the edges and corners smooth and rounded for new plastered area exceeding 30sqm in width or girth including preparation of surface and two coat of cement base paint /apex as required over one coat of primer including formwork/scaffolding work upto height 7.0mtr above ground level of bldg complete all as specified.

M&L for Reinforced cement concrete (Nominal mix), type B1, 1:2:4 (using 20 mm graded crushed stone aggregate) as in chajjas, balcony, landing work if any including demolition of existing reinforced cement concrete (reinforcement cut as required to facilitate demolition) complete all as specified and as directed by Engineer -in-Charge.

Formwork to sides and soffits/facia of floor or roof beams, beam haunchings, girders, bressummers, lintels, chajja, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

S&F mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises

M & L Green Marble work 18mm to 20mm thick (table rubbed and polished) in steps of staircase/kitchen platform and like in cement mortar (1:4) inclduing pointing in white cment (1:2) using marble dust with admixture of pigment ot match with marble shade of Green marble including 15mm thick screed bed/base in CM 1:4, roughening/cleaning to existing surface of old concrete floor by picking, sweeping clean and washing down with water to remove dirt/dust and brushing neat cement slurry with 3.0 kg of cement per sqm all as specified and as approved by the GE/Engr-in-Charge.

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match including 15 mm thick screed bed in cement and sand mortar 1:4 all as specified and as approved by the GE/Engr-in-Charge.

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, in floors/skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match including 15 mm thick screed bed in cement and sand mortar 1:4 all as specified and as approved by the GE/Engr-in-Charge.

M&L for Glazed ceramic tiles, coloured 300x200x6-7mm thick on vertical surface such as skirting/dado over & jointed in neat cement slurry & pointed in white or coloured cement to match the shade of tiles including 10 mm thick in CM 1:4 bedding layer to receive tiles complete all as specified and as directed by Engineer-in-Charge.

M&L for machine cut kota stone slab flooring 18-20mm thick as in flooring jointed with grey cement slurry mixed with pigment to match the shade or the slab including rubbing and polishing complete including 20mm thick screed bed in CM 1:4 for laying floor finishes complete all as specified and as directed by Engineer-in-Charge.

Machine cut kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete,over and including 10 mm thick rendering in cement and sand mortar 1:4. all as specified.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm not exc 4.0 Sqm each complete including making good disturbed portions of wall with new or old bricks , lintels cills etc in CM 1:4 complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 Sqm each including making good disturbed portions of wall with new or old bricks, lintels cills etc in CM 1:4 complete all as specified and directed.

M & L Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia thresh old bar and filling hollow of frame .

M & L Pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia thresh old bar and filling hollow of frame.

PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate as in filling of pressed steel frame.and including 50 mm parapet coping all as specified etc complete all as specified and directed by Engineer-in-Charge.

S & F 35mm thick Flush shutters, solid core with block board core qne plywood face panels, commercial type on both side as per IS-2202 of 199 (Part-I). Flush door shutter shall be internally lipped as per clause 8.52.2 of SSR-2009 Part-I complete all as specified and directed by Engr-in-Charge.

S&F Glazed and skelton shutters 30 mm thick second class hard wood, opened rebated and prepared to receive wire mesh etc, edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for sucuring witre mesh etc. Size of members of shutters as specified in SSR Part-I, Sec-8, clause 8.24(a).

S&F 150mm, Mild steel ordinary rat tail rod pattern springs including roller and roller plates complete all as specified and directed.

S&F 100 mm butt hinges, medium weight cold rolled mild steel all as specified and directed.

S&F 75 mm butt hinges, medium weight cold rolled mild steel all as specified and directed.

S&F Aluminium anodised handle extruded section and fixed in repairs of size 150mm all as specified and directed.

S&F Aluminium anodised barrel tower bolts extruded section of size 200mm, all as specified and directed

S& F Hasp and stapple safety type of aluminium anodised 100 mm long as a cupboard locker complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt of length 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of sections or cast-aluminium extruded alloy and fixed complete all as specified and directed.

S&F Small fittings such as bracket of any type, latch and hinge blocks, shaped door and window stops and the like including all necessary labour, article not exc. 200 cu.cm each of 2nd class hard wood, complete all as specified & directed.

S&F Steel windows/ventilator (Box type) factory made with double shutter (wire gauged shutter & glass/glazed shutter, (wire cloth and glass panes shall be measured and paid separately) of size 79mmx39mm,16 gauge rectangular tubular frame with side hung shutter with glazing bars 12x3mm flat iron incl box type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100mm long and 10mm square bar grills complete, two coats of synthetic enamel paint over one coat of red oxide primer including all as specified & as shown on drg No. CEUZ/TD/1269/2008 Sh no 1/1 to 1/3.

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, or galvanized wire staples all as specified & directed.

S&F Glazing with sheet, 4mm thick, ordinary quality and glazing with oil putty and glazing pins in squares not exceeding 0.5 Sqm in each pane all as specified & directed.

S&F figured glass sheet, 4mm thick, ordinary quality and glazing with oil putty and glazing pins in squares not exceeding 0.5 Sqm in each pane all as specified & directed.

S&F Floor door stopper 140mm overall length of cover plate of aluminium alloy body and tongue,nodised,with hard drawn steel spring,fixed in bottom body of door complete all as specified and directed by Engineer-in-Charge.

M&L prelaminated solid board 18/19mm thick exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screw to timber frame in repairs as cupboard shelve and shutter, complete all as specified and directed.

M&L pre laminated particle board, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screw to timber frame in repairs as cupboard shelve and shutter, 12 mm thick. (Kitchen cup board/covered bottom shelf of cooking platform).

M & L extra over rates of block board or veneered particle board for external teak wood lipping, 6mm thick fixed with nails all as specified and directed.

M & L Plain, solid, straight chowkats and frames made out of 2nd class hard wood (sal), wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, supplied and fixed, complete all as specified and as directed by Engineer-in-Charge.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top and bottom rails. M.S frame shall be covered with heat channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as a gap insert for top rail and bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S frame welded / sealed to the stiles and nails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at side as per specification and drawings.

Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube, supplying and fixing in opening as per specification and drawing.

S&F curtain rail, 20 mm dia anodised aluminium alloy ,cromium plated fixed with braket, incl taking down of old curtain rods, all as directed.

M&L preparation of new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

Painting to new wood or wood based surfaces of any description not otherwise described over 10 cm in width or girth including preparation of surfaces, priming with pink primer (one coat) finished with two coats of synthetic enamel paint complete all as specified.

M&L for 50 mm thick 75 cm wide PCC type C-1 1:3:6 (using 20mm graded stone aggregate) as in plinth protection laid in bays complete including 75mm thick consolidated hard core of broken stone over rammed earth finishing the surface of concrete topping even & fair, without using extra cement filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand (all by weight) complete all as specified and as directed by Engineer-in-Charge. Note :- The rate quoted shall be deemed to include for use and waste of form work / screed strips and to divide the area in panels including hardcore.

S&F rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down of old existing water tank complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel water tubing 20 mm dia and connections complete all as specified.

Taking up or down steel water tubing 15mm dia and connections complete all as specified.

S&F Steel water tubing medium grade galvanised ISI marked with all fitting and fixed to wall and ceiling or laid in floors of 20mm bore all as specified and directed.

Fixing only steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc) of nominal bore dia 20 mm, all as specified.

S&F Steel water tubing medium grade galvanised ISI marked with all fitting and fixed to wall and ceiling or laid in floors of 15mm bore all as specified and directed.

Fixing only steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc) of nominal bore dia 15 mm, all as specified.

S&F in repair stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, for bore dia of pipe 15mm, complete all as specified and directed by Engineer-in-Charge

S&F in repair stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, for bore dia of pipe 20mm, complete all as specified and directed by Engineer-in-Charge

S&F in repair ball valve high pressure of PTMT with epoxy coated Aluminum rod & high density plastic ball screwed for iron pipe or brass ferrule 20mm bore (minimum weight 210 gms) , complete all as specified and directed by Engineer-in-Charge.

S&F PVC (Plastic polymer Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete, fixed in repairs.

S&F vitreous china squtting pan "Orissa Pattern" size 580 x 440 mm in any coloured with integral foot rest incl lime motor, 'S' trap and complete all as specified, fixed in repairs complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm size complete all as specified and directed.

S&F Tubular towel rail aluminium anodised 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls, complete all as specified and as directed by Engineer-in-Charge.

S & F in repair stainless steel cockraoch traps Single piece in a box size 101 x 101mm with waste hole complete all as specified

S&F in repair Swivel shower of PTMT any colour for fixing with 15 mm pipe ,with shower arm of size 195 mm long with bend of 54 degree with flange of any colour (minimum weight 40 gm) complete all as specified.

S & F unbreakable (square wall mounted shelf 500mm) glass shelf to be fixed in wall complete all as specified and direceted.

S & F unbreakable corner glass shelf (3 Pieces of Set) fixed to wall complete all as specified

S & F bathroom mirror cabinet 400 x 500mm fixed to wall including complete accessories.

S & F Vitreous china wash basin, white, flat back size 550 x 400mm excluding taps, waste, chain, and plug and porcelian stopper but including brackets fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

S & F Pillar tap fancy type capstan heads, chromium plated screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified

Taking down eaves gutters, CI soil and waste pipes (any size or pattern) including including all fittings, heads, shoes bends, swan necks etc all as specified.

S & F PVC (SWR) floor trap 75mm plain with grating including joints with solvents cement completed all as specified and directed.

S & F in repairs PVC SWR bends any radius 110 mm bore all as specified.

S & F PVC SWR (Type B) waste pipes 110 mm dia in any length fixed to walls with CI/MS holder but clamps and conforming to IS-1729 complete all as specified and directed.

All as description of Srl No 91 here-in-above but 75mm bore.

All as description of Srl No 91 here-in-above but 50mm bore.

S&F PVC (SWR) Bends (any radius) diminishing pieces or tapers (larger bore measured) for PVC SWR pipes fixed in repairs, 110 mm bore complete all as specified and directed.

S & F PVC branch pipes 110mm single equal or unequal ordinary or inverted (spigot or socket type) fixed in repair with paralled branches all as specified and directed.

S & F PVC branch pipes 110mm double equal or unequal ordinary or inverted (spigot or socket type) fixed in repair with paralled branches all as specified and directed.

S & F PVC junction, single, equal or unequal, ordinary or inverted with spigot or socket branch of 75mm bore complete all as specified and directed.

All as per Srl Item No 97 here-in-above if provided 110mm bore with access door CI cover complete all as specified.

S & F PVC cowls 100mm fixed in repairs all as specified directed.

S & F PVC 50mm vent horn fixed in repairs complete all as specified.

S & F Plate rack made of stainless steel 0.8mm thick overall size 786mm x 610mm x 254mm complete all as specified and directe by Engineer-in-Charge.

S & F in repair kitchen sink with solo regular single bowl gloss finishing stainless steel 1.00 mm thick sheet for kitchen with plugs, washers and wastes including fixing in reinforcement cement concrete slab and connecting union to pipe overall 510 x 430 x 203 with complete fittings all as specified and as directed by Engineer-in-Charge

Brass CP mixer for sink, cast copper alloy (ISI Marked) fancy type chromium plated for mixing hot and cold water screwed down high pressure with capstain head screwed both ends for iron pipe 15mm bore fixed in repairs complete all as specified and directed.

Bib taps, cast fancy type , chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, for bore dia of pipe 15mm, supplied and fixed in repairs complete all as specified

S&F CP brass wall mixture with telephonic shower arrangement for mixing hot cold water supply screwed down including connecting legs & wall flanges for iron pipe 15mm dia bore fancy type in repair complete all as specified and directed.

Brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 including demolition of existing brick masonary built in cement mortar including all quoins arches etc but excluding ashlar masonry complete all as specified and as directed by Engineer -in-Charge

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade with grey cement and no pigment over a layer and including 25mm thick sand cushioning complete all as specified and directed.

S & F Joist, channel, angle or tee section Fe 410-W Gde E-250 Afixed independently without connecting plates etc fixed to wall for cooler rest angle work all as specified and directed.

S & F PVC (SWR) 110 mm dia single socketed in any length with rubber ring joints, laid in floors completed all as specified and directed.

S & F PVC (SWR) 75 mm dia single socketed in any length with rubber ring joints, laid in floors completed all as specified and directed.

Sunken Floor Treatment: Providing and laying of water proofing treatment to sunken portion by applying cement slurry mixed with acrylic based polymer modified cementious composite compound of make as approved including demolition and filling of sunken floor. (i) First layer of slurry of cement @0.488 Kg/Sqm mixed with acrylic based polymer modified cementious composite compound @0.253 Kg/ Sqm. This layer allowed to air cure for 4 hours. (ii) Second layer of cement @0.242 Kg/Sqm mixed with acrylic based polymer modified cementious composite compound @ 0.125 Kg/Sqm. This layer allowed to air cure for 4 Hours. Note: Concrete for sunken slabs shall be mixed with WP compounds as manufacturer's instruction before carrying out water proofing treatment. The sunken slab/ dampness is seen in ceiling below, then treatment is again carried out to RCC slab and it is again tested (Water proof compound rate is separately)

Fixing 20mm dia PVC nozzles and injection grouting using heavy duty cementious waterproofing coating as in roof slab all as per manufacturer's instruction complete all as specified and directed.

Taking down carefully, copper / aluminium conductor unserviceable / perished point wiring (any type) for light/ fan/ light socket or power socket etc complete with fittings such as switches, sockets, ceiling roses, pendant holders, bracket holder, light fittings, regulators etc, including making good to disturbed surfaces of wall/floor etc, complete, all as specified & directed.

M&L for Sub main wiring with two runs of 6.0 Sqmm single core FRLS PVC insulated unsheathed cable upto and including 1100 volts grade with multistranded copper conductor drawn through in and including PVC surface conduit or casing caping of 20/30mm, 2.0 mm wall thickness (ISI marked) with all fittings and fixing accessories, surface type on walls, roofs etc including one run of 2.50 Sqmm FRLS PVC insulated copper conductor for earth continuity wire in green color including taking down carefully existing copper submain wiring with PVC surface conduit or casing caping and making good disturbed surfaces complete all as specified & directed by Engineer-in-Charge. Note:- Two runs of copper conductor 6.0 sqmm and one run of 2.50 Sqmm copper earth wire including PVC casing caping will be measured and paid as one unit only.

M&L for Point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 1.5 Sqmm drawn into and including PVC concealed conduit 'ISI marked' of 20mm dia medium grade as required, fixed in concealed surface of wall/ceiling including cutting chases as required, terminated in MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one light/fan/bell point controlled by one way switch, complete all as specified & directed.

All as per Srl item No. 116 here-in-above but for one 3/5 pin 5 Amps socket outlet on independent board.

All as per Srl item No. 116 here-in-above but for one 3/5 pin 5 Amps socket outlet on same board with other switches.

All as per Srl item No. 116 here-in-above but for one point controlled by two way switches.

M&L for point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable 1100 volt grade, single core of 2.5 Sqmm drawn into and including PVC concealed conduit 'ISI marked' of 20mm dia medium grade as required, fixed in concealed surface of wall/ceiling/false ceiling including cutting chases as required, terminated in MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one 3/5 pin socket outlet 16 Amps controlled by one switch on independent board, complete all as specified & directed. Notes for Srl Item No. 91 to 94 (i) Unit rate includes for cutting chases whereever required and sinking for boxes, making good to walls / floors etc., complete, including white wash / colour wash as directed. (ii) Uniform coding of wiring i.e red / yellow / blue for phase black for neutral and green for earth is to be maintained.

Supply & fixing modular type switch 6 Amps, single pole, 1way,1 module,240V, ISI Marked complete all as specified and directed. Make Indoasian Glint,Crabtree, Havells REO

Supply & fixing modular type switch 16 Amps, single pole,1 way,1 module,240V, ISI Marked Complete all as specified and directed. Make Indoasian Glint,Crabtree, Havells REO

Supply & fixing modular type socket shuttered type 6 Amps- 2/3 Pin combined 2 module,240V,AC ISI Marked Complete all as specified and directed. Make Indoasian Glint,Crabtree, Havells REO

Supply & fixing modular type socket 6 A/16 Amps -2/3 Pin combined shuttered socket 2 module 240V AC ISI Marked Complete all as specified and directed .Make Indoasian Glint,Crabtree, Havells REO

Supply & fix fan regulator modular type electronic, stepped type 100 Watts, 2 module 240Volts,AC ISI marked complete all as specified and directed. Make Indoasian Glint,Crabtree, Havells REO

S&F in replacement buzzer, ding dong AC 230 volts single pole ISI marked complete all as specified & directed.

S&F in modular bell push 6A, 1 module, 240 volts, single pole ISI marked complete all as specified & directed. Make Indoasian Glint,Crabtree, Havells REO

S&F ceiling rose 5 amp, 3 plates polycarbonate body complete all as specified & directed.

Supply and fixing VTPN verticle loadline double door distribution box (DB) are fitted with Bus bar neutral link, blanking plates of 4 way with suitable for incomming MCCB 'I/C' frame,having isolated neutral bar, mechanical impact strength IK09,door earthing suitable for MCCB upto 125 Amp Note Rate of MCCB has included in the quoted rate. Make -Indoasian part No- 811888 or its equivalent in Havells ,Legrand, L & T etc.

Supply and fixing sheet metal enclosure double door type for DBs single pole and neutral 8 way 240 V with 200 Amp bus bar including blanking plates where required including fixed flush in wall chases wall for fixing DB and making good surfaces to match with existing surface all as specified and directed. Make : Indoasian, Legrand, Schiender, Havells etc.

S&F in replacement MCB, single pole, (SP) 6 to 32 Amp, AC, 10 KA repturing capacity, ISI marked, 240 Volt, 'C' series, including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified & directed by Engineer-in-Charge.

Supply & fix MCB SPN 32 to 40 Amps 10 KA,"C" series, AC, 240Volts, 50Hz, ISI marked complete all as specified and directed Make : Legrand, Schiender, Havells etc.

S&F Earthing of galvanized steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr depth below normal ground level) with top edge of earth not less than 1.5 metre below normal ground level, surrounded on all sides by 150mm thick charcoal & common salt starting from ground below earth plate upto 150mm above GI plate in alternate layers connected to and including earth lead wire 4.0mm (8SWG) by means of steel bolts, nuts, check nuts and washers, test point made of GI strip 40x8mm, 10cm long PCC 1:2:4, type B-1 in pit with precast RCC 1:2:4 type B-1 in cover reinforced with XPM not less than 4 Kg per Sqm with 15mm bore GI light grade protection pipe, 20mm bore GI medium grade watering pipe with funnel including charcoal, dust, salt, all as shown in electrical plate No 3 of SSR Part-I (2009) including taking down old existing earthing complete with necessary earth work in any type of soil, removal to a distance not exceeding 50 mtr, including testing on completion, complete all as specified & directed. Note : (a) The cost of earth work, PCC pit of size shown in electrical plate No.3, funnel, watering pipe, wire mesh, charcoal, dust, common salt, 20mm bore medium grade watering pipe & 15mm bore light grade GI pipe as protection to earth lead wire etc shall be deemed included in the unit rate for earthing. (b) After completion, during testing, if the earth resistance equal or less 2 ohms is not obtained, earthing will be regenerated at no extra cost till the desired earth resistance is obtained.

Taking down UNSV flourescent fitting and M & L for LED batten Regal suitable for T8 LED tube incl T8 LED tube crystal glass with very high efficacy suitable for installation in existing T8 fitting with G13 lamp 20 watt 4 ft long all as specified and directed. Make : Havells Part No for batten- REGALBATTENT8UPTO1X22W DSBSWH, Cat Part No- LED Tube T8 : CRYSTAL1213T8DSTL18WLED865SGLASS or equivalent in CG, Philips, Bajaj . Note :- Rate quoted include the cost of both batten and Tube rod T8 and shall match with the batten .

Supply and fixing ceiling fans complete with blades. Down rods, electronic regulator and accessories, 230 volt, 1200mm sweep, min air delievery 210 CFM with service value 6 BEE five star rated with brushless direct current motor (BLDC) incl taking down existing and deposit with MES all as specified and directed.

Material & Labour for surface & wall mounted LED tube light fitting 10W, 2 feet long extruded PVC housing provided for efficient heat dissipation to polycarbonate diffuser & integrated electronic driver with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed. Make- Havells catpart No ENDURALINEARNEOBS10W LED865SPCWH OR equivalent in Philips/ Crompton/ Bajaj/ Wipro

Taking down old unserviceable Exhaust fan of any type/size from existing location and deposit in MES store yard and Supply and fix exhaust fan single phase metal body, AC 230 Volt, 50 Hz of size 300mm sweep with louvers shouter complete with all accessories including connecting up from ceiling rose to motor all as specified and directed. Make : Havells, Bajaj, Cromption etc.

S & F in replacement of 20 Watt LED energy saving light fitting environment friendly long life LED street light made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK 07 with GI bracket made of light grade GI pipe 40 mm dia of 1.2 mtr long bend to shape with 02 Nos of FI clamp 32 x 4mm with suitable size nuts, bolts, washers etc. and making the connection from ceiling rose to fitting with suitable size twin core copper conductor cable complete all as specified and directed . (Make- Havells, cat part No ENDURACITYLITEPLATSL20WLED757SASYBOPC or Bajaj/Philips/Crompton Greaves or its equivalent).

Supply, laying and testing XLPE insulated, electric cable (heavy duty) with stranded aluminium conductor, 1100 volts grade, heavy duty cable, cross-sectional area 50 Sqmm 3.5 core laid in trenches or passing through pipes complete all as specified and directed. (Earth work, brick protection and sand cushioning shall be measured and paid for separately) Make: Polycab, Gloster, Grandlay

Brick well burnt locally available sub class 'B' laid over sand cushioning for mechanical cable protection in trenches with width of brick perpendicular to the length of cable, complete all as specified & directed by Engineer-in-Charge.

Sand cushioning to under ground cable, laid in trenches 8cm thick below the cable and 15cm thick above the cable after laying and stretching the cable complete punned to 18cm, complete all as specified and directed. Note:- Punned thickness of sand will be measured and paid.

CHOPRA CONSTRUCTIONS

M/s Rajesh Kumar Contractor

M/S KARAN SINGH CONTRACTOR

M/s Joginder Lal Malhotra