SPECIAL REPAIR TO OR GOVT MD ACCN BLOCK NO. 1163/01 TO 12 AT AJMER LINE IN ARMY AREA JODHPUR UNDER GE (A) NO. 01

Amount

Demolition of unreinforced cement concrete in ground floors and pavings not exceeding 15cm thickness ( below or above ground level) of any description and removing rubbish to out side MD land complete all as specified and as directed.

M&L plain cement concrete 1:4:8 type D-2 by using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified and as directed.

M&L 50 mm thick PCC 1:3:6 type C -1 using 20 mm graded stone aggregate laid in alternative bays as in plinth protection including finishing the surface even & fair & filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight complete all as specified and as directed.

M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified & as directed.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified & as directed.

Demolition of stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified & as directed.

M&L for cutting in to old masonry to form toothings for bonding in new brick or stone work including making good in cement mortar 1:6 complete all as specified and directed.

M&L for squarred rubble walling Jodhpur type regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6 complate all as specified and directed.

All as per item No 8.00 here-in-above but except stone complate all as specified and directed.

M & L pre-cast cement concrete block masonry using PCC, 1:2:4, type B-1 solid blocks, not exceeding 10 cm in width and setting in cement mortar 1:4, straight or curved on plan exceeding 6 m mean radius complete all as specified and as directed.

Extra over squared rubble stone walling Jodhpur type regular course for hammer dressing to face of stone with max depression on face from a straight edge not exc 20mm and dressing complete to squared rubble walling, regular coursed, Jodhpur typeall as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

M/L for 25mm thick PCC 1:2:4 type B-0 by using 12.5mm graded crushed stone aggregate in base for tile floors, finished even and smooth with using extra cement complete all as specified and as directed.

M&L non skid ceramic tiles, coloured, of size exceeding 0.18 Sq.m and not exceeding 0.38 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles over and including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 complete all as specified and as directed.

All as per Sl. Item No. 14.00 here-in-above, but as in skirting over and including 10 mm thick backing coat in CM 1:4

M&L non skid ceramic tiles, coloured, of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles over and including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 complete all as specified and as directed.

M & L coloured glazed ceramic tiles of size 450mmx350mmx7mm/ 450mm x 300mm x 7mm thick on vertical surface of wall over and including 10mm thick backing coat in CM 1:3 set and jointed in neat cement slurry and pointed in white cement / coloured cement to match the tiles complete all as specified and as directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid dry or laid dry and pointed complete all as specified and directed.

M & L 18 to 20 mm thick machine cut Kota stone slab flooring ,cooking plate from etc over screed bed base ,laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing icluding 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M & L 18 to 20 mm thick machine cut Kota stone in riser of steps, skirting, dado and piller laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing including 10 mm thick rendering in cement mortor 1:6 complete all as specified and directed.

M & L 18 to 20 mm thick machine cut Kota stone in self and other places etc laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing complete all as specified and directed.

M & L 18 to 20 mm thick machine cut one side polished black granite in kitchen plate form, set and jointed including 20 mm thick screed bed in cement mortar 1:3, laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing complete all as specified and directed.

Taking down existing cement plaster including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 10mm thick rendering in CM 1:4 over stone masonary surfaces incl finishing the surface fair & rough to receive tiling etc complete all as specified and directed.

M&L Rendering 10 mm thick CM (1:3) on concrete surfaces on ceiling / facia /RCC Chhaja etc all as directed & finished even & smooth complete all as specified & directed.

M&L Rendering 5 mm thick CM (1:3) on concrete surfaces on ceiling / facia /RCC Chhaja etc all as directed & finished even & smooth complete

M&L for 15mm thick rendering in CM 1:6 finished even and smooth without extra cement on stone wall surface complete all as specified & directed.

Racking out joints/pointing to square rubble masonry Jodhpur type regular coursed built in cement mortar all as specified

M&L for Keyed pointing to square rubble masonry Jodhpur type regular course in CM 1:3 all as specified.

M&L Preparing new plastered or unplastered surfaces and applying with wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper over one coat of primer on walls complete all as specified and as directed.

M&L for Complete removal of existing treatment of walls and applying two coats of oil emulsion distemper on wall surface over one coat of primer over one coat of wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces complete all as specified and as directed .

M&L preparing new plastered or unplastered surfaces and applying three coats of white wash on wall complete all as specified & directed by Engineer-in-charge.

M & L Preparation of new plastered or unplastered surfaces and applying three coats of white wash on ceiling surfaces, to match with the existing surface complete all as specified and as directed.

M & L Preparation of old decorated surfaces of walls and applying one coat of white wash complete all as specified and as directed.

M & L Preparation of old decorated ceiling surfaces and applying one coat of white wash complete all as specified and as directed. .

M & L Preparation of new plastered or un-plastered surfaces of walls and applying two coats of cement base paint over a coat of white wash to match with the existing surface complete all as specified and as directed.

M&L for Preparation of old painted surfaces of walls and applying one coat of cement base paint complete all as specified and as directed.

M & L Preparation of new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed .

M&L preparation of steel surfaces of any description over 10cm width or girth not otherwise described and apply two coats of synthetic enamel paint over & including M&L one coat of red oxide zinc chrome primer complete all as specified & directed

Taking down chowkhats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutters) complete all as specified and as directed.

Taking down chowkhats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutters) complete all as specified and as directed.

Taking down Shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each complete all as specified and as directed.

Taking down Shutters of any description and refixing the shutters in the same opening of any description exceeding 1.00 Sq.m and not exceeding 2.00 Sq.m each after easing and adjusting complete all as specified and as directed.

M&L rolled mild steel sections like angle, channel, flat, square etc as in framed work such as grills, gratings, etc, with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars ,barred iron doors; ladders ;framed balusters walk ways railings framed work of water tanks and similar work confirming to Fe-290Gde E-165 complete all as specified and as directed.

M&L for mild steel framed brackets for cooler stand made out of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel'), complete all as specified & directed.

S&F mild steel frame work as in stairs ,hand rails half round or other stock section or section or core for wooden hand rail straidgt portion drilled and countershunk for balusters running bars for doors balusters nosing to steps including embeded in concrete and screwing etc hid ties for foof including securing bolts post and struts in fencing including securing bolts post and struts in fencing including cutting tops to shape as directed drilling holes nothing for wire etc flat iron fillet for necessary drilling boltinh or riveting etc and similar work confirming to Fe 410-0 or fe 310-0

M &L as in repairs for fabrication of pressed steel cupboard shutters using 1.00 mm thick MS plain sheet & with frame 1.25 MM thick bent to shape incl two coats of syn enamel paint on int surfaces & two coats of hammer tone finish on external surfaces alongwith locking arrangement mortice lock handle etc complete all specified and directed.

M&L 35mm thick factory made 2nd class HW glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part-I Section 8 Clause 8.24 (a), including Aluminium Grill Medium grade mess size 50x50mm , fixed at outer edge at outer edge of door & SS wire cloth 0.36mm nominal dia of wire, average width of aperture 1.40mm fixed with SS wire staple. complete all as specified and as directed.

M&L factory Made flush shutters, 30 mm thick solid core with block board core, commercial type both sides, construction as per IS 2202(part-I, 1999) . The stiles & rails shall be with out any joint and made with non- coniferous timber hard wood (Hillock/ Mirantee/ Bosum/ Benteak) with moisture content not less than 12% as per IS. The face panel comprising of ply wood or cross band and face veneers shall be glued by hot pressed process. The over all finished thickness of face panel shall not be less than 30mm while the thickness face veneer shall not be less than 0.6 mm complete all as specified and directed.

M&L 35mm thick factory made 2nd class HW glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part-I Section 8 Clause 8.24 (a) complete all as specified and as directed.

S/F of factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made of MS tubes for top & bottom rail. MS frame shall be covered with heat moulded plain color pvc ‘C’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain color pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted to the MS Frame/sealed to the stiles & rails with suitable PVC sheet beading, and joined 30mm thick (style) consisting of frame made of MS tubes for top & bottom rail. MS frame shall be covered with heat moulded plain color pvc ‘C’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain color pvc sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail paneling of plain colour PVC sheet to be fitted the MS Frame/sealed to the stiles & rail with suitable PVC sheet beading, and joined together with solvent cement, all as specified.

M/L for solid PVC door frame of size 50x47mm made out of 5mm thick pvc sheet reinforced with MS square tube all as specified.

Taking down steel windows and ventilators ( glazed / fly proof) of any description complete all as specified and as directed.

S&F Factory made box type steel windows ( glazed) with side hung shutters including pintol hinges with 2 nos MS barrel tower bolt and steel handle and steel peg stay complete with glazing bars, dovetailed or welded, including single shop coat of Zn chromate primer (with or without cooler opening) all as specified and as directed.

All as per Sl. Item No. 55.00 here-in-above, but without glazing bar

S&F Factory made box type steel ventilators with top hung shutters including pintol hinges with MS barrel tower bolt and steel handle and steel peg stay complete with glazing bars, dovetailed or welded, including single shop coat of Zn chromate primer, complete all as specified and as directed.

All as per Sl. Item No. 57.00 here-in-above, but without glazing bar

S&F for 200mm size aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F 300 mm length aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed.

S&F for 100mm size, butt hinges, stainless steel including necessary welding if required complete all as specified and as directed.

S&F Butt hinges,100mm size, cold rolled mild steel, medium weight, complete all as specified and as directed.

S & F 125 mm size single action floor spring main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed.

S & F floor door stopper of size 140 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.

M&L for Figured glass 4.00 mm thick , pin head type and glazing with putty in square not exceeding 0.50 Sqm in each pane complete all as specified and as directed.

S&F for sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

S&F glavanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aparture 1.00mm and fixed with tinned tack or galvanised wire stapples complete all as specified and as directed.

M&L for plain cement concrete 1:2:4 type B-1 by using 20 mm graded stone aggregate as in bed block for fixing of hold fast complete all as specified and as directed.

M&L for mild steel work as in hold fasts, clamps, bands, straps or stays, wall ties, hooks etc confirming to Fe - 290, Grade E-165 including prepartion of surfaces and treated with coal tar and sanded with clean sharp sand complete all as specified and as directed.

S&F MS with PVC coated decorative 25mm curtain rod with fixing brackets, knob etc as in repairs complete all as specified and directed.

S&F in repair shelf of PTMT fixed with and including chromium plated brass screws and wooden cleats (Min weight 300 gms) complete all as specified and directed.

S&F in repair soap dish of PTMT fixed with screws complete all as specified and directed.

S&F in repair PTMT towel rail 450mm long fiexd to wall with chromium plated brass screws and woodn cleats Min weight 170gms approved make complete all as spcified and directed.

S&F in repair MS chromium plated peg set of five fixing with wall complete all as specified and directed.

S & F in repairs stainless steel kitchen sink with drainage board, made of stainless steel 1 mm thick, with plugs, washers and waste pipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to waste pipe, over all size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed.

S & F in repairs white vitreous china squatting pan "Orissa pattern" of size 580 mm X 440 mm with integral foot rests and PVC 'P' or 'S' trap with 32 dia HDPe pipe including provision of cement concrete bedding 1:5:10 type E2 complete all as specified and as directed.

S & F as in repairs vitreous china wash down water closet Anglo Indian Type pedestal pattern with seat & cover complete incl fixing of flush pipe etc complete all as specified and directed.

Vitreous china wash basin white, flat back of size 550 X 400mm white including 32mm size waste fittings, brass, chromium plated, coupling, waste pipe of 32mm dia, MS brackets including cutting for and pinning in ends of brackets errect stand, fixing waste pipe, complete all as specified and as directed.

Dismantling of cast iron or AC drain pipe/ PVC pipe jointed in cement mortar of size 110mm bore as directed

Dismantling of cast iron or AC drain pipe/ PVC pipe jointed in cement mortar of size 75mm bore as directed

S & F sand cast, cast iron, soil / waste / vent pipes, 100mm bore, in any length with or without ears, jointed with cement sand mortar, laid in trenches or in floors complete all as specified and as directed.

S & F sand cast, cast iron, soil / waste / vent pipes, 75mm bore, in any length with or without ears, jointed with cement sand mortar, laid in trenches or in floors complete all as specified and as directed.

S & F sand cast, cast iron, soil / waste / vent pipes, 100mm bore, in any length with or without ears, jointed with cement sand mortar, fixed to walls with and including MS clamps complete all as specified and as directed.

S & F sand cast, cast iron, soil / waste / vent pipes, 75mm bore, in any length with or without ears, jointed with cement sand mortar, fixed to walls with and including MS clamps complete all as specified and as directed.

S & F cast iron branch pieces with ovall access door, single [equal or unequal] ordinary or inverted [spigot and socketed type] or with parallel branches suitable for 100mm dia pipes complete all as specified and as directed.

All as per Sl. Item No. 87.00 here-in-above, but suitable for 75 mm bore pipe

S & F cast iron bends with ovall access door [any radius], diminishing pieces or tapers [larger bore measured] of 100mm bore, for cast Iron soil / waste / vent pipes complete all as specified and as directed.

All as per Sl. Item No. 92.00 here-in-above, but suitable for 75 mm bore pipe

S&F 100mm dia CI vent cowl fixed to pipe complete all as specified and directed.

S&F cast iron floor trap 75mm dia out let, with CP grating including jointing to waste pipe fixed in cement concrete 1:2:4, Type B-1 complete all as specified and as directed.

S &F in repair brass chromium plated shower rose of size 50mm with or without swivel joints fixing to steel pipes complete all as specified and as directed.

S &F in repair pillar taps, brass chromium plated fancy type , long body with areator, screwed down high pressure, with or without lettered 'Hot' & 'Cold' with long screwed shanks and fly nuts, screwed for 15 mm bore iron pipe complete all as specified and as directed .

S &F in repair 25 mm dia stop valves, cast copper alloy with screw down high pressure with crutch or butter fly handle screw both ends for iron pipe or for union & fixed of 25mm dia all as specified specified.

S &F in repair brass chromium plated fancy type Angular stop cock with wall flange , screwed both ends for 15 mm bore iron pipe or for unions complete all as specified and as directed.

S &F in repair brass chromium plated fancy type two way Angular stop cock with wall flange , screwed both ends for 15 mm bore iron pipe or for unions complete all as specified and as directed.

S & F in repair CP fancy type hand shower, (Health faucet) with 1.2m long SS flexible tube with wall hook with Non Return Valve [back flow preventer] complete all as specified and as directed.

S& F as in repairs 15 mm dia stop cock regular body with adujstable wall flange with chromium plated with (concealed type) all as specified

S/F as in repairs of 15 mm dia bib, cock long body with flange with chromium plated fixed with iron pipe complete all as specified and directed.

S & F in repair CP central hole basin mixer with regular spout with out popup waste system with 450mm long braided hose with connecting legs and wall flanges complete all as specified and as directed.

Supply only 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of 32 mm dia and PVC connection 15mm size, 450 mm long with PTMT nuts complete all as specified and as directed.

Disconnecting existing tanks exc 250 ltr and n exc 500 ltr, setting aside (or lowering if required) for repairs ,cleaning,etc and hoisting if required reconnectioning and refixing in position, complete all as specified and directed.

M & L for 500 ltrs capacity rotational moulded polythene water storage tanks white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I, complete all as specified and as directed.

S&F in repairs ball valves for 20mm bore pipe, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball complete all as specified and as directed. (minimum weight 210 gms)

S & F in repairs stainless steel plate rack of size 750mm X 600mm X 200mm of approved pattern made out of stainless steel sheet 18 gauge with round 8mm dia rods complete all as specified and directed.

Taking out from position framed woodwork as in cupboards/cabinets etc with all fittings ,shutters, shelves, drawers etc in any position fixed in walls or floors & removal of the rubbish outside MD land all as directed at site for overall sizes exc 0.50 sqm but nexc 1.50 sqm & depthd nexc 60 cm complete.

Providing and fixing polyvinyl chloride (PVC) sheet frame of width 150 mm & 18 mm thickness made out of extruded 18mm PVC sheet and joined with suitable Cement Solvent adhesive and screw.The frame shall be fixed to the wall using 75mm long M.S. Screws through the frame by using PVC fasteners. A minimum of 3nos. of screws to be provided for each vertical member & minimum 2nos. for horizontal member etc. complete as per manufacturers specification and direction of Engineer-in-Charge.

M&L for 18 mm thick solid PVC sheet UPVC Caoted Celuka printed in one of two different colours( with wood grain printed pattern /ivory clour finish) as in kitchen cabinet shutters ,and cupboard shutter all round body of cabinets , shelves ,drawers etc cut to required size jointed with solvent cement & steel screws etc complete all as specified & directed .

S & F Auto hinges, stainless steel, complete assembly complete all as specified and directed.

Extra over PVC boards for lipping 1-1.5 mm thick 18 mm wide complete

S&F degree clip type self closing hinges for cabinets fized with cadimum coated screws all as per sample.

S&F 100mm size bright finished cromium plated steel handle of approved shape & design fixed with cadmium coated screws on the kitchen cabint shutters

S&F 75mm size bright finished cromium plated steel handle of approved shape & design fixed with cadmium coated screws on the kitchen cabint drawers

S&F magnetic catches for cabinets of size 50 mm complete with striking plate & magnetic stud complete all as per approved smaple.

S&F drawer runners folding type with guide channels & sliding channel with approipiate ball bearing/ rollers etc complete to obtain smooth movement of the drawers.

M&L for stainless steel tray as per trade pattern of various sizes for drawer to keep the kitchen utensil as directed by Engineer-in-charge

M&L 50mm thick PCC (1:2:4) type B-1 using 20mm graded crushed stone aggregate for plate form for water tank on roof complete all as specified & directed

Demiolition of reinforced cement concrete of as staircase, landing, chajjas or roof, colums ,beam of any type etc and similar suspended work of any description and any position not otherwise, and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and as directed.

M&L for RCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in precast manhole/drain covers including demolition of RCC slab, manhole/drain cover in any position complete all as specified and as directed.

S&F 5 cm thick sand stone slabs Jodhpur pattern/colour in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc not exceeding 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar (1:4) complete all as specified & directed by Engineer-in-charge.

Supply only water proofing compound complete all as specified & directed by Engineer-in-Charge

Taking up or down existing 25 mm bore GI tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed

All as per serial item No. 123.00 here-in above but 20 mm bore tubing

All as per serial item No. 123.00 here-in above but 15 mm bore tubing

Refixing of old steel tubing 25 mm bore with fittings, in new or old position fixed to wall/ laid in trench/ceiling, complete all as specified and as directed

All as per serial item No. 126.00 here-in above but 20 mm bore tubing

All as per serial item No. 126.00 here-in above but 15 mm bore tubing

Supply, laying, jointing and testing galvanized iron tube 25 mm bore medium grade with all fittings such as bends, elbows , socket, reducer & etc and fixed to wall, ceiling or laid in floors, complete all as specified and as directed

All as per serial item No. 129.00 here-in above but 20 mm bore tubing

All as per serial item No. 129.00 here-in above but 15 mm bore tubing including cutting chases, pinning in & making good to disturbed portion to match the existing surface etc complete.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including fair finished surfaces complete all as specified and directed.

Use and waste formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide includingrough finished surfaces complete all as specified and directed.

Use and waste of form work to sides and soffits of lintels, beams, brackets, shelves and similar works for rough finished surfaces of concrete complete all as specified and as directed.

RCC M-25 design mix as in slabs supported on walls, beams and colunms in floors,roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

RCC M-25 design mix as in beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and as directed.

S & F TMT HYSD bar 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

S & F TMT HYSD bar 6 to 8 mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

S & F TMT HYSD bar 5 dia and over upto and including 10 mm dia as in stirrups cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

M&L for screeding / bedding layer of 10 mm thick in CM 1:3 mixed with water proofing compound as per manufacturer instructions over the RCC roof slab for laying of water proofing treatment including providing the following as roof treatment complete all as specified and as directed : - (a) FIRST COURSE: Applying a coat of bituminous primer @ 0.4 litre / Sqm manufactured by the same agency that of APP with a density 0.87 to 0.89 Kg/litre at 25 degree celsius on prepared plastered surfaces. (b) SECOND COURSE: Applying one coat of bonding material using blown type bitumen conforming to IS-702 grade 85/25 @ 1.20 Kg/Sqm (c) THIRD COURSE : Provide a layer of APP modified polymeric membrane centre core of 100mm micron HMHDPE, outer film 20 micron each, thickness 2.00mm having weight not less than 2.25 Kg/Sqm using torch application method with minimum 10cm side lap and 15cm end lap complete . (d) FOURTH COURSE : Applying one coat of bonding material using blown type bitumen confirming to IS- 702 grade 85/25 @ 1.20 Kg/Sqm. NOTE :- WPC shall be measured and paid separately under respective item.

Taking down carefully copper/aluminium point wiring for light, fan, bell socket power slocket etc complete with boards, outlet boxes fittings and fixtures such as switchs, sockets, lamp holders bracket, ceiling rose etc complete

Taking down existing old sub main wiring Including DB's of any size and make complete all as directed

Point wiring complete with 1.5 sqmm, single core, multi stranded, copper conductor, PVC (FRLSH), insulated, unsheathed cable, confirming to IS-694, 1100 volts grade, ISI marked (class V conductor), in and including PVC concealed conduit (MMS), ISI marked not less than 20mm, with accessories fixed on surface of wall/roof/ceiling etc and including sunken pressed steel terminal boxes in wall but including 3mm thick plastic laminated sheet top cover (ISI marked hylem sheet and 1.50 sqmm PVC insulated unsheathed stranded copper conductor for common earth and connecting to earth dolly material and labour for :- (a) One light/fan/bell point controlled by one, one way switch

All as per serial item No. 143.00 here-in-above, but suitable for one socket outlet 5 pin 6 Amps on same board

All as per serial item No. 143.00 here-in-above, but suitable for one socket outlet 5 pin 6 Amp on independent board

All as per serial item No. 143.00 here-in-above, but suitable for one light point controlled by two , two way switches.

All as per serial item No. 143.00 here-in-above, but with 2.5 Sq mm single core multistanded copper conductor cable for 3 pin 16 Amp socket outlet on independent board .

S&F switch flush type single pole one way 6 Amp, 230 Volts, ISI Marked, complete all as specified and directed.

S&F switch flush type single pole one way 16 Amp 230 Volts ,ISI Marked, complete all as specified and directed.

S&F socket out let , 5 pin , 6 Amp 230 Volts, complete all as specified and directed.

S&F socket out let , 5/6 pin ,16 Amp Flush type 230 V, ISI Marked, complete all as specified and directed.

S & F Bell push, flush type, 5 amp ISI marked 230 V, complete all as specified and directed.

S & F Bell Ding Dong AC. 230 volts,single pole ISI marked, complete all as specified and directed.

S & F 5 amp two way switch 230 Volts ISI Marked, complete all as specified and directed.

S&F socketed stepped type electonic fan regulator flush type , ISI Marked, complete all as specified and directed.

S & F Ceiling rose, 3 terminal/PVC/ polycarbonate, isolated body, ISI Marked, complete all as specified and directed.

Supply & Fixing only LED lights fitting 1x 20W, 220V, including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and Fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V including connecting up with three core flexible copper conductor cable of suitable size complete all as directed.

S&F insulated Batton lamp holder metal cased body of brass with back plate suitable for batton fittings including 9 watt LED Lamps ISI Marked, complete all as specified and directed.

S & F LED Bulb 9 Watts, complete all as specified and directed.

S&F connecting, and commissioning of street light fitting 25 watt LED , IP-65 protection, single peice pressure dia cast aluminium alloy housing high grade powder coated finish with heat resistant toughned clear glass cover for lamp and contror gear compartment with high voltage surge protection device upto 4.5 KV, Prewired including 1.60 mtr long 40mm bore light grade GI pipe mounting bracket made to shape with and including MS clamp of F1 40 mmx6mm with bolts , nuts & washers and conductor to fitting with 3 core 1.5 sqmm pvc insulated cable complete all as specified

M & L for taking down and Hanging only ceiling fan and connecting up including provision of copper flexible twin core cableof size 23/0.0076 from ceiling rose or connector to fan

M/L in repairs sub main wiring with 6.00 Sq mm single core multistrandred copper conductor PVC insulated and unsheathed cable passing through PVC concealed conduit and making good the distrurbed surface of wall inc 6 Sq mm single core copper conductor cable PVC insulated and unsheathed cable as earth wire. Note :- Two runs of cable 6 Sqmm and One run of 6 Sqmm shall be measured as unit length.

S&F inreplacement , testing factory made sheet metal enclosure for MCB DB SPN 8 way 240 volt with double door, IP - 43 protection duly fixed/concealed in wall complete and making good disturbed surfaces of wall, floor etc including necessary connection lugging with copper lugs pin/ring type all as directed by Engineer-in-Charge.

S&F inreplacement, testing factory made sheet metal enclosure for MCB DB TPN 4 way 415 volt with double door, IP - 43 protection duly with fixed in wall/ concealed in wall complete and making good disturbed surfaces of wall, floor etc including electric wire connection all as directed by Engineer-in-Charge.

S&F inreplacement, MCB single pole 230 volts any rating from 6 to 32 amps, with rupturing capacity 10 KA, 'B' curve type, with over load and short circuit protection.

S&F inreplacement, MCB single pole and neutral 240 volts any rating from 63 amps, with rupturing capacity 10 KA, 'B' curve type, with over load and short circuit protection.

S&F inreplacement, MCB triple pole and neutral 415 volts 63 amps, with rupturing capacity 10 KA, 'B' curve type, with over load and short circuit protection.

M & L for taking down existing electric meter of any size any capacity and take in safe custudy and refix in same position all as directed by Engr - in Charge.

M & L for replacement Earthing complete with galvanised steel earth plate electrode 60 x60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) wih top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in elevtrical plate no. 3 connected to Earthing test point all as specified or indicated including testing on completion Note : (i) Rates are deemed to be included for necessry earth work ,PCC pit , RCC cover etc complete. (ii) Earth lead shall be up to 7.5 Mtr and rates are deemed to be included for GI pipe 15mm Light grade upto 7.5 mtrs for protection of earth wire 4.0 mm dia.

Supply and layin replacement in trenches/on wall/on pole/in duct /through protection pipe, XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables heavy duty LT cable, 1100 volts grade with aluminium conductor cross sectional area 16 Sqmm 4 core size including retrieving/taking out/taking down old unserviceable cable from duct/trenches/pipes/pole/wall etc. including brick cover and protection pipe and disconnecting the connections. Note:- Excavation and earth work, sand cushioning, PCC cable cover and protection pipe etc. shall be measured and paid for separately.

Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plain area and not exceeding 1.5m deep in hard/dense soil complete all as specified and directed.

M&L for dry clean fine river sand as in sand cushioning to underground cable including punning down of sand layer all as specified and directed. Note :- Punned thickness shall only be measured and paid.

Supplying and laying un-reinforced precast concrete cable cover, class LV, type 1, flat, size 250x150mm x40 mm

M&L for galvanised steel tubing, light grade, for protection of cable, laid in trenches/road crossing/floor or fixed to pole/wall with all fittings, of size 40 mm bore.

Returning filling in including spreading , leveling , watering and well ramming in layer n. exc 25 cm complete all as specified and as directed.

M & L Removal of surplus loose soil from excavated place and deposting at safe side distance not more than 50 meter from excavated place all as directed

Harsh Enterprises