Development of Infrastructure Facilities

Amount

SUB HEAD-I - EARTH WORK

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. (a) All kinds of soil Note:-As per IS:1200 (Part 27) :1992, method of measurement Earth work, 4.7 (lift), Earth work any kind of Soil /Rock done by Mechanical Appliances, lift for the same shall not be measured separately, even if it is more than 1.5m.In this case max depth of Excavation is 13m (approx.) for which no extra payment will be made.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. Ordinary rock Note:-As per IS:1200 (Part 27) :1992, method of measurement Earth work, 4.7 (lift), Earth work any kind of Soil /Rock done by Mechanical Appliances, lift for the same shall not be measured separately, even if it is more than 1.5m.In this case max depth of Excavation is 13m (approx.) for which no extra payment will be made.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. Hard rock (blasting prohibited) (The credit material shall be the property of the Contractor). The quoted rate deemed to include the credit material. Note:-As per IS:1200 (Part 27) :1992, method of measurement Earth work, 4.7 (lift), Earth workany kind of Soil /Rock done by Mechanical Appliances, lift for the same shall not be measured separately, even if it is more than 1.5m.In this case max depth of Excavation is 13m (approx.) for which no extra payment will be made.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. (a) All kinds of soil.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating Nos deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50m. (a) All kinds of soil Pipes, cables etc, not exceeding 80 mm dia.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating Nos deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50m. (b) Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating Nos deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Supplying chemical emulsion in sealed containers including delivery as specified.

Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: (a) With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

SUB HEAD-II - REINFORCED CEMENT CONCRETE

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : (a) 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : (a) 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: (a) 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Centering and shuttering including strutting, propping etc. and removal of form for all heights :

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Extra for shuttering in circular work

Weather shade, Chajjas, corbels etc., including edges

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete at all level. (a) Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.(Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). :

All works upto plinth level

All works above plinth level upto floor V level

(a) Extra for Providing M-30 grade concrete over and above M-25 Grade BMC/RMC at all floor levels. (Note:- Cement content considered in M-30 is @340 kg/cum) Note:- Excess/less cement over the specified cement content used is payable /recoverable separately.

Add for using extra cement in the items of design mix over and above the specified cement content therein.

SUB HEAD-III - BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:4 (1 cement : 4 coarse sand)

Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : (a) Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. (a) Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : (a) Cement mortar 1:6 (1 cement : 6 coarse sand)

SUB HEAD-IV - DOOR & WINDOW WORK

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile C (a) Fixing with adjustable lugs with split end tail to Nos jamb

Deduct for not providing hinges in doors, windows or clerestory window shutters with : Stainless steel butt hinges with stainless steel screws. (a) For 2nd class teak wood and other class of wood shutters

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : (a) 300x16 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish,(Barrel type) with necessary screws etc. complete : (a) 150x10 mm

Providing and fixing rubber wall buffer for doors of size 50mm. Long including necessary screw etc. Compleat.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : (a) 300x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : (a) 300x10 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : (a) 200x10 mm

Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws bolts, nut and washers etc. complete.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : (a) 125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. (a) Twin rubber stopper

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: (a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. (a) With 12 mm mild steel U beading

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including Patch Lock with strike plate having 3Nos high securty computer keys make ozone/Enox at Bottom and 600 mm length providing stainless steel brush finished handles of 25mm dia both side on Nos door and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. (a) Using M.S. angels 40x40x6 mm for diagonal braces

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. (a) 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Extra for providing mechanical device chain and crank operation for operating rolling shutters. (a) Exceeding 10.00 sqm and upto 16.80 sqm in the area

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of as per required size, joints mitred and welded by angle iron as per required flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge.

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). (a) Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. (a) In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing Z ventilation of GI pipe having dia. 150 MM. With perforated cover Including fixing in 1:2:4 cement concrete compleate as per detail drawing and approved by engineer incharge.

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. (a) 10 x 160 mm

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. (a) Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : (a) 4.0 mm thick glass panes

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion (a) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) (a) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin-charge. (a) Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): (a) With float glass panes of 4.0 mm thickness (weight not less than 10 kg/ sqm)

Extra for providing etched glass panes instead of ordinary float glass panes in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

SUB HEAD-V - FLOORING

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. completeat all levels. Granite of any colour and shade (a) Area of slab over 0.50 sqm

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. (a) Granite Stone of approved shade

Providing and fixing antiskid Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. (a) 18 mm thick

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. (a) 40 mm wide and 4 mm thick

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : (a) Agaria White

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Udaipur green marble

Marble work gang saw cut (polished and machine cut) of thickness 18 mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately)

Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble.

Area of slab upto 0.50 sqm

Providing and laying antiskid rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying double charged, mat finish vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. (a) Size of Tile 600x600 mm

Providing and laying double charged, mat finish Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete (a) Size of Tile 600x600 mm

SUB HEAD-VI - ROOFING

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single socketed pipes (a) 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° (a) 110 mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe (Plain). 110 mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. (a) 110 mm

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm Nos having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm. long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with:

8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.

Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main CB269:B270 carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with :

GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.

SUB HEAD-VII - FINISHING

12 mm cement plaster of mix : (a) 1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix with fine sand : (a) 1:6 (1 cement: 6 fine sand

15 mm cement plaster on rough side of single or half brick wall of mix with coarse sand: (a) 1:6 (1 cement: 6 coarse sand)

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : (a) 1:4 (1 cement: 4 fine sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

6 mm cement plaster of mix : (a) 1:3 (1 cement : 3 fine sand)

Extra for providing and mixing water proofing material in cement. Note : 1 Kg water proofing compound to be used per bag of cement or as per manufacture's specification.

White washing with lime to give an even shade : (a) New work (three or more coats)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : (a) New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: (a) New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : (a) Two or more coats on new work

SUB HEAD-VIII - WATER SUPPLY & SANITARY INSTALLATIONS

Providing and fixing white vitreous china wall mounting water closet of size 570x340x360 mm of approved shape including providing & fixing PVC concealed cistern of Size 460x450x80mm with dual flush plate fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc including painting of fittings and cutting and making good the walls and floors wherever required : complete.

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board. (a) 610x460 mm bowl depth 200 mm

Providing and fixing towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and . (a) 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm. make JAQUAR ACN-1111N or equivalent.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineerin- charge.

Providing and fixing soap Dish Holder with concealed fitting arrangements.Make Jaquar ACN-1131N or equivalent.

Providing & fixing CP brass Health faucet with PVC Flexible Tube with wall hook.( JAQUAR MODEL NO-573 or Equivalent.)

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing toilet paper holder : (a) C.P. brass

Providing and fixing soil, waste and vent pipes : 100 mm dia (a) Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989

Providing and fixing unplasticised Polyvinyl Chloride (UPVC) pipes, having thermal stability for hot & cold sewage supply including all UPVC plain fittings This includes jointing of pipes & fittings with one step UPVC solvent cement, & testing of joints complete as per direction of Engineer in Charge. (a) 100 mm nominal inner dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 32 mm dia nominal bore

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 20 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 40 mm nominal outer dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 50 mm dia nominal bore.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 65 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 80 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete: (a) 50 to 80 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 65 mm nominal bore.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : (a) 25 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length (a) 15 mm nominal bore

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 25 mm diameter pipe

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 32 mm diameter pipe

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 40 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 50 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 65 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 80 mm dia nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. (a) Circular tank

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : (a) 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. (a) 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. (a) 15mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

SUB HEAD-IX - DRAINAGE

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement :1 fine sand) including testing of joints etc. complete : 100 mm diameter

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement :1 fine sand) including testing of joints etc. complete : 150 mm diameter

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement :1 fine sand) including testing of joints etc. complete : 200 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 100 mm diameter S.W. Pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 150 mm diameter S.W. Pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 200 mm diameter S.W. Pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150 x 100 mm size P type (a) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement :4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

nside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : (a) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, totai weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg): (a) With common burnt clay F.P S. (non modular) bricks of class designation 7.5

Extra for depth for manholes Size 90x80 cm (a) With common burnt clay F.P.S. (non modular) bricks of cass designation 7.5

Size 120x90 cm (a) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Supplying and fixing C.I. cover without frame for manholes: (a) 455 x 610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg

560 mm diameter C.I cover (medium duty) the weight of the cover to be not less than 108 kg

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality H D - 20 (a) Circular shape 560 mm internal diameter

Providing , lowering, laying and cutting (cut surface to be uniformly finished) UPVC pipes IS :15328. Jointing with coupler of click ring and rubber sealing rings for 250mm size and solvent weld type coupler for 315 mm and 400mm dia pipes and specials into trenches of all depth including carriage,loading,unloading etc. comlete in all respect to the satisfaction of the engineer-in-charge. (a) 100mm Pipe

Providing , lowering, laying and cutting (cut surface to be uniformly finished) UPVC pipes IS :15328. Jointing with coupler of click ring and rubber sealing rings for 250mm size and solvent weld type coupler for 315 mm and 400mm dia pipes and specials into trenches of all depth including carriage,loading,unloading etc. comlete in all respect to the satisfaction of the engineer-in-charge. (b) 200mm Pipe

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.w. dran pipe 100 mm diameter, 1.8 m long complete as per standard design. (a) With common burnt clay F.PS. (non modular) bricks of class designation 7 .5

SUB HEAD-X - WATER PROOFING

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of : (i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. (ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer.

Using rough kota stone.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge : (a) Using rough Kota stone

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (i) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment (ii) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (iii) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (iv) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (v) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :

With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

SUB HEAD-XI - INTERNAL ELECTRIFICATION

LIGHT POINT WRING Point wiring for Light / fan / Exhaust fan with 2 runs of 1100V grade 1.5 sq. mm & 1 run of 1.5 sq. mm FRLS insulated multistranded Copper wires, run in & including 25 mm dia , Heavy class PVC conduit concealed in wall after necessary chase cutting with finishing / surface on wall/ ceiling conforming to IS 732 including all accessories such as junction boxes, conduit bends, elbows and ceiling rose, anodised GI switch box with modular switch and the box covered with front plate.

(a) One Light point controlled by one 6A switch ).

Two Light point controlled by one 6A switch ).

Exhaust fan point controlled by one 6A switch including ceiling Rose.

One ceiling fan point controlled by one 6A switch With 100W step type Electronic regulator including Concealed MS fan hook box.

Light Fixtures Supply, Installation, Testing & Commissioning of the following Light Fixture with lamp, Control Gear & All necessary accessories. Luminaries with all electrical accessories & it should be energy efficient, low loss, ortho cyclically wound open construction copper ballast, ignitor & power factor improvement capacitor or Electronics Ballast etc are prewired up to the terminal block & mounted on a removable control gear module for ease of maintenance. All electrical connections of the control gear module with the rest of the luminaries should be click fix & require use of no tools. Mounting options should be for both lateral as well as pole top mounting. with Lamp Control Gear & Fixing Accessories. (a) 20W LED BATTEN LIGHT WALL/SURFACE MOUNTED MAKE-PHILLIPS CAT NO. BN108C 20S PSU CDL WH

33W LED RECESSED MOUNTED LUMINAIRES MAKE-PHILLIPS Model No. - SM200C LED11S 6500PSU 1100 LUMEN

16W LED Recessed mounted Downlighter MAKE-PHILLIPS CAT NO. DN394B LED16S-6500 PSR-P WH

10W LED surface mounted DOWNLIGHT MAKE-PHILLIPS CAT NO.DN092B LED10S-6500 PSU WH

10W BULKHEAD LIGHT MAKE-PHILLIPS CAT NO. WT202W LED6S NW PSU S2 PC

8W MIRROR LIGHT Surface Mounted MAKE-PHILLIPS CAT NO. 34093/11

22W Surface Mounted LIGHT MAKE-PHILLIPS CAT NO. WL060V LED17S/840 PSU II WH

Crompton Flameproof LED Tube Light ,Surface Mounting Type FOR 20W TUBE LIGHT ITEM CODE -EXTN2LT8-16 20, 65 lm W,

FANS/EXHAUST FANS Supplying, Installation, testing and commissioning of ceiling fan of 1200mm sweep suitable for operation on 230/240V, 50Hz, single phase, AC Supply complete with double ball bearing motor, of ceiling fan, including wiring the down rods of 600mm length with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including phenolic laminated sheet cover on the fan box etc. as required.

Supplying & Installation of exhaust fan in the existing opening, including gravity louver, making good the damage, connection, testing, commissioning etc. as required. (a) 250mm Metal exhaust fan

6A SWITCH & SOCKET Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

CIRCUIT/SUBMAIN WIRING Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4X 2.5 sq. mm + 2X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 16 sq. mm + 2 X 10 sq. mm earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 32 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

PrProviding and fixing 105x50 mm DLP UPVC adaptable trunking system fittings trunking / raceway including accessories etc as all complete.

Supplying and fixing suitable size UPVC box with modular plate and cover in front on surface in existing raceway, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size UPVC box with modular plate and cover in front on surface in existing raceway, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supply and fixing 1 Module,UPVC box along with modular base & cover plate for modular switches on surface in existing raceway etc all as directed Engineer - in - Charge.

DISTRITUTION BOARD Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (a) 8 way , Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way (4 + 18), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar,din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) (a) 4 way (4 + 12), Double door

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing verticle distribution board including drilling holes in Board, making connections, etc. as required. (a) 150 A, 16 KA,TPMCCB

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) Single pole

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) 40 A

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) 40 A

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A

SUB HEAD-XII - AC SYSTEM

Supply, installation, testing and commissioning of split outdoor & one indoor unit with cordless remote suitable for operation on 230 volt, 50 Hz, single phase AC supply outdoor stand etc. all complete. (a) 2 TR Capacity - 5 star rating

Supply, installation, testing and commissioning of voltage stabilizer AC SINGLE PHASE 5KVA Automatic operation having input voltage 170 to 270 Volt and output voltage 240v. Complete with voltmeter, high and low voltage cut off & time Delay relay type digital voltmeter.

Supply, installation, testing and commissioning of following size soft copper piping with insulation of 6mm thick nitrile rubber preformed sections including supporting fixtures and accessories etc. as complete (a) 1/2" dia

Supply and laying of drain piping using 1" dia UPVC pipe with accessories etc. as complete

Supplying , installation, testing and commissioning of unarmoured copper power cable of 2.5 sqmm x 3 core PVC insulated, including cutting, chasing, PVC Casing Caping of required Size & necessary accessories etc as complete in all respect.

MS Powder Coated Stand for installation of outdoor units 2TR Capacity - 5 star ratiing

Air Conditioning (under ground control room) HIGH SIDE VRV/VRF SYSTEM : outdoor units Supply, installation & testing of Modular type outdoor Condensing units equipped with highly efficient Scroll Compressors, inverter type compressor(s), special acryl precoated e-Pass heat exchanger, low noise condensor fan with DC motor, auto check function for connection error, auto address setting, M.S Stands with nominal capacities as mentioned below: (a) 10 HP (Actual) 2 Working+1 Stand By

INDOOR UNITS: Supply, installation, testing & commissioning of Air Cooled VRV/VRF Ceiling mounted built-in type/ ductable type Indoor uniis equipped with pre-filter, fan section with low noise fan, multispeed motor, coil section with DX coil, electronic expansion valve, outer cabinet, drain pan, insulation, including y Joints pipe connections, control and power panel with Cordless remote control etc. of various capacitles as Per specifications & drawings. 1.80 TR at Control Room

Supply, installation, testing & commissioning of Air Cooled VRVVRF Ceiling mounted built-in type/ ductable type Indoor uniis equipped with pre-filter, fan section with low noise fan, multispeed motor, coil section with DX coil, electronic expansion valve, outer cabinet, drain pan, insulation, including y Joints pipe connections, control and power panel with Codeless remote control etc. of various capacitles as Per specifications & drawings. 3.80 TR at Confrence Room

Supply, installation, testing & commissioning of Air Cooled VRVVRF Ceiling mounted built-in type/ ductable type Indoor uniis equipped with pre-filter, fan section with low noise fan, multispeed motor, coil section with DX coil, electronic expansion valve, outer cabinet, drain pan, insulation, including y Joints pipe connections, control and power panel with Codeless remote control etc. of various capacitles as Per specifications & drawings. 3.80 TR at Work Station

Supply, installation, testing & commissioning of Air Cooled VRVVRF Ceiling mounted built-in type/ ductable type Indoor uniis equipped with pre-filter, fan section with low noise fan, multispeed motor, coil section with DX coil, electronic expansion valve, outer cabinet, drain pan, insulation, including y Joints pipe connections, control and power panel with Codeless remote control etc. of various capacitles as Per specifications & drawings. 1.80 TR at UPS Room

Supply, installation, testing & commissioning of Air Cooled VRVVRF Ceiling mounted built-in type/ ductable type Indoor uniis equipped with pre-filter, fan section with low noise fan, multispeed motor, coil section with DX coil, electronic expansion valve, outer cabinet, drain pan, insulation, including y Joints pipe connections, control and power panel with Codeless remote control etc. of various capacitles as Per specifications & drawings. 3.80 TR at Visitor Lobby

Supply, installation, testing & commissioning of Air Cooled VRVVRF Ceiling mounted built-in type/ ductable type Indoor uniis equipped with pre-filter, fan section with low noise fan, multispeed motor, coil section with DX coil, electronic expansion valve, outer cabinet, drain pan, insulation, including y Joints pipe connections, control and power panel with Codeless remote control etc. of various capacitles as Per specifications & drawings. 3.80 TR at Store Room

VENTILATION: Cabinet Fan:- Supply, installation, testing and commissioning of Inline fans complete with motor, supporting frame, gravity louvres,etc. as per drawings and specifications. (a) 900 CFM @25mm Static (Cabinet Type)

03 Nos. 40 Amps TP RCCB/ELCB 16KA For 10 HP ODU (2 Working + 1 Spare) with ON/OFF Indication. 02 Nos. 10 Amps DP MCB 16KA with starter For Ventilation Fans (2Working+0 Spare) with ON/OFF Indication. 08 Nos. 10 Amps DP MCB 16KA with For IDU (6 Working + 2 Spare) with ON/OFF Indication. 01 Nos 40Amps DP16K breaking capacity. 01 Nos 63Amps TPN 16K breaking capacity 01 Nos 40Amps TPN 16K breaking capacity.

(B) LOW SIDE INSTALLATION AND ALLIED WORK CORDED REMOTE CONTROL Supply, installation, testing and commissioning of Corded Remote Controller for Indoor Units with all complete.

CONTROLIZED REMOTE CONTROL Supply, installation,testing &commissioning of centralised remote controllers for operation & status monitoring of VRV/VRF indoor units with all complete.

REFRIGERANT PIPING Supply, installation,testing & commissioning of interconnecting refrigerant pipe work with (19mm/13 mm thick), Class O', k value-0.035 w/mk minimum, density not less than 55 Kg/cu.m closed cell elastomeric nitrile rubber tubular insulation between Nos set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with MS hanger & clamps. 34.9 mm O.D. (insulation: 19 mm)

Supply, installation,testing & commissioning of interconnecting refrigerant pipe work with (19mm/13 mm thick), Class O', k value-0.035 w/mk minimum, density not less than 55 Kg/cu.m closed cell elastomeric nitrile rubber tubular insulation between Nos set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with MS hanger & clamps. 28.6 mm OD. (insulation: 19 mm)

Supply, installation,testing & commissioning of interconnecting refrigerant pipe work with (19mm/13 mm thick), Class O', k value-0.035 w/mk minimum, density not less than 55 Kg/cu.m closed cell elastomeric nitrile rubber tubular insulation between Nos set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with MS hanger & clamps. 22.2 mm O.D. (insulation: 13 mm)

Supply, installation,testing & commissioning of interconnecting refrigerant pipe work with (19mm/13 mm thick), Class O', k value-0.035 w/mk minimum, density not less than 55 Kg/cu.m closed cell elastomeric nitrile rubber tubular insulation between Nos set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with MS hanger & clamps. 19.1 mm OD. (insulation: 13 mm)

Supply, installation,testing & commissioning of interconnecting refrigerant pipe work with (19mm/13 mm thick), Class O', k value-0.035 w/mk minimum, density not less than 55 Kg/cu.m closed cell elastomeric nitrile rubber tubular insulation between Nos set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with MS hanger & clamps. 15.9 mm OD. (insulation: 13 mm)

Supply, installation,testing & commissioning of interconnecting refrigerant pipe work with (19mm/13 mm thick), Class O', k value-0.035 w/mk minimum, density not less than 55 Kg/cu.m closed cell elastomeric nitrile rubber tubular insulation between Nos set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with MS hanger & clamps. 12.7 mm OD. (insulation: 13 mm)

Supply, installation,testing & commissioning of interconnecting refrigerant pipe work with (19mm/13 mm thick), Class O', k value-0.035 w/mk minimum, density not less than 55 Kg/cu.m closed cell elastomeric nitrile rubber tubular insulation between Nos set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with MS hanger & clamps. 9.5 mm O.D. (insulation 13 mm)

Cable Tray

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray with cover (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. (a) 200 mm width X 50 mm depth X 1.6 mm thickness with cover

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray with cover (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. (b) 300 mm width X 50 mm depth X 1.6 mm thickness with cover

DRAIN PIPING Supply. installation, testing and commissioning of rigid PVC piping complete with fittings, supports as per specitications and duly insulated with 6 mm thick closed cell nitrile rubber class '0' , As required. (a) 40 mm dia

Supply. installation, testing and commissioning of rigid PVC piping complete with fittings, supports as per specitications and duly insulated with 6 mm thick closed cell nitrile rubber class '0' , As required. (b) 32 mm dia

Supply. installation, testing and commissioning of rigid PVC piping complete with fittings, supports as per specitications and duly insulated with 6 mm thick closed cell nitrile rubber class '0' , As required. (c) 25 mm dia

DUCTING: G.I. Sheet Ducting(Site Fabricated) - Supply.Installation, testing & commissioning of sheet metal leak proof ducting complete with necessary angle channel supports, hangers, nuts,bolts, anchor fastners washers, rubber gaskets etc., as per specifications and drawings.All ducting of any size should be flanged type and no slip joints will be allowed All joints, corners of the ducting to be applied with silicon sealant for leak proof joints. Cost of smoke testing of the ducting as per specification/site instruction is to be included. The ducting system shall conform to the SMACNA-1995 standards ("HVAC Duct Construction Standards-Metal and Flexible-Second Edition-1995" SMACNA). (a) 26 Gauge

DUCT INSULATION Supply, installation, testing of thermal insulation of supply air ducting (return air collected through duct) with closed cell Nitrile Rubber (CLASS O) with prelaminated Aluminium foil on one side having a low stable k value of 0.035 k.cal/hr.m at 10 degree C and minimum density of 40-55 +3 kg/cum.The R.value should be as per ECBC Code. (a) 13 mm thick

GRILLS/DIFFUSER Supply, installation, testing and commissioning supply and return air grilles/ difusers as per specifications and drawings Including fixing frame of G.l/wooden in false ceiling/walls. (a) Aluminium supply air grill with damper

Supply, installation, testing and commissioning supply and return air grilles/ difusers as per specifications and drawings Including fixing frame of G.l/wooden in false ceiling/walls. (a) Aluminium return/exhaust air grill without damper

Supply, installation, testing and commissioning supply and return air grilles/ difusers as per specifications and drawings Including fixing frame of G.l/wooden in false ceiling/walls. (a) Aluminium supply air diffuser with damper

Supply, installation, testing and commissioning supply and return air grilles/ difusers as per specifications and drawings Including fixing frame of G.l/wooden in false ceiling/walls. (a) Aluminium return/exhaust air diffuser without damper

FLEXIBLE CONNECTION Supply, installation, testing& commissioning of fire retardant nonporous double layer flexible connection between Nos duct type indoor unit and ducting.

CONTROL & TRANSMISSION WIRING Supply, installation, testing & commisioning of control cum transmission wiring of 2 core 15 sqmm copper wire in suitable PVC conduits between indoor & out dor unit & outdoor units to central remotes controllers

WEATHER PROOF ISOLATOR Supply, installation, testing and commisioning of weather proof box with 40/63 Amp MCCBs 25KA of suitable rating near the outdoor units for isolations all complete.

POWER CABLE Providing and fixing of PVC armoured copper FRLS cabes from panel boards to the uníts through walls/ceing With appropriate clamps and fixing arrangements and end termination etc. as per specifications and drawings. (a) 4 Core - 16 Sqm

Providing and fixing of PVC armoured copper FRLS cabes from panel boards to the uníts through walls/ceing With appropriate clamps and fixing arrangements and end termination etc. as per specifications and drawings. (a) 4 Core 2.5 Sqm

SYSTEM COMMISSIONING Commissioning of VRV/VRF System including Topping of R410A gas as per site requirements

SUB HEAD-XIII - TELEPHONE AND DATA SYSTEM

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc.as required. (a) 1 or 2 Module (75mmX75mm)

Supplying and fixing of following sizes of Heavy class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. (a) 25 mm

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. (a) 2 Pair

Providing, fixing connecting and testing of under noted size of solderless telephone tag block Connector in surface/recess in wall required size of M.S. box with hinged lockable cover duly stove enamel painted. (a) 10 Pair Tag Block

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (a) Telephone socket outlet (RJ11)

Supplying and fixing of modular type Lan (RJ-45) outlet in existing Box complete as required. (a) Computer socket outlet (RJ 45)

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. (a) 2 run of cable

SUB HEAD-XIV - LIGHTNING PROTECTION

Supply and installation of 10 mm dia 1000 mm long Al. vertical interception rod with 150 m m dia base mounting plate, quick connector to connect upto 10 mm dia round conductor and all fixing accessories etc, equivalent to OBO Type no. F- Fix-Junior

Supply and laying of 8 mm dia aluminum round Conductor With cross connectors and expansion joint etc complete in all respects and as directed by Engineer in charge. In accordance with DIN EN 50164-2 (VDE 0185 part 202) & VDE 0185-305 (IEC 62305), Equivalent to OBO Type No. RD 8/ALU

Supply and installation of Roof Conductor Holder for Parapet wall having hole Ø7 mm all as specified in drawing and directed by Engineer, made of polyamide OBO Type No. 177 55 M8.

Supply and installation of Plastic conductor Holder for RCC Roof made Sleeve from polyethylene, black, bottom polypropylene and alla accessories equivalent to OBO Type No. 165 MBG

Supply and installation of expansion piece with Connector 2Nos connector and 1 Expansion Piece) as specified in drawing and directed by Engineer, OBO Type no. 172 AR + 249/ST.

Supply and fixing of Cross connector for 8 mm dia Aluminum Round Conductor on the roof/parapit wall equalent to OBO Type Cat No. 252 8-10 V4A

Down Conductor Supply and installation of 8 mm dia Aluminum Round Conductor complete in alla respects and Meets the requirements of VDE 0185-305 (IEC 62305) , similr to OBO type No. RD 8/ALU

Supply and installation of Down Conductor Holder for wall having hole 7 mm, made of polyamide including all fixing accessories equivalent to OBO Type No. 177 55 M8.

Supply and installation of Test Joint (Saddle Clamp) suitable to connect 8mm dia round conductor and max by 25x5 mm Cu strip equivalent to OBO Type No. 271 8-10 VA, With max 25x5 mm Cu strip holder 163 100 CU or Equivalent.

Supply installation and testing of Lightning counter suitable to connect with 8mm dia round conductor at both the ends as required and accessories, equivalent to OBO Type No. LC01

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supply, Erection , commissioning of Maintenance free earth station consisting of 40mm Dia 3m long copper electrode capsule field with earth enhancing compound sealed at both ends and brazed Lead for connection at one end, Suitable for direct installation at side with brass bolt at the top end, with nuts & Washers including Mesonary enclosure, CI Coverwith frame and interconnection along with earth pit Identification board and as required spreading of earth enhancing chemical compound etc.Complet the Scope Also includes Excavation in all type of soil, back filling and makinng the area neat & etc. complete

SUB HEAD-XV - AV SYSTEM WITH EV MODELS

Supply Installation, Testing & Commissioning of of FLAT LED MONITOR 55" Compatible with CCTV Multiviewers Slim LED Aspect Ratio: 16:9, Display resolution- 1080P PIP (Picture-In-Picture), VGA, HDMI/ DVI Interface, Remote Control Included, including Wall Mounts Available

Supply, Installation, testing & commissioning of Controller for Video Wall/Projector with Windows Based Controller with 9 Slot PCI Express Chassis, Intel Core i7 Processor, redundant & hot swappable power supply 8 DVIVDP outputs, 8 Universal inputs (DVINGA/HDMI), Wall Management Software, Matrix Configuration ( Any input to any Output )necessary cable to Connect to Video wall panels, keyboard and mouse, AntiVirus Software pre loaded. Makes: Barco Hantarex / Delta.

Supply, Installation, Testing & Commissioning of Mutiformat Digital Data Transmitter for transmission of Data Video signal from laptop ( HDMI VGA / Display port ) with 4 switches to connect laptopS XPVista/7/8/8.1 32 & 64 bit Mac OSX 10.6/10.7/10.8/10.9 Android 2.2), Video outputs- DisplayPort, Single link DVI-I VGA, "Dual screen" mode, Frame rate Up to 30 fps, Output resolution DVI WUXGA (1920x1200) DisplayPort panoramic format (2560x1600) Input Resolutions Up to 2880x1800 Noise Level Max. 28dBA , Multiple images display on screen Upto 4),Simulataneous connections upto 64 pcs., Analog audio output Base Unit. Makes Barco/ Wowvision

Supply, Installation, Testing & Commissioning of Floor Box with face flate for Connectivity with cable cubby having One CAT 6 RJ-45 .Approved Make: Customized.

Supply, installtion, testing and commisssioning of CeilingLoudspeaker, Two Way 110 Hz to 15 kHz or better frequency range (-10 dB) , 50 watts or better powe handling capacity ,86 dB sensitivity (1W/1m), 8 ohms nominal impedance, 130 conical coverage (polar). Make VAL Martin Audio / Tannoy/EV

Supply , Installation Testing & Commissioning of Professional quality audio amplifier with dual channel, 200 + 200 watts, frequency response (1w 8 ohm stereo) 20 hz- 20 khz (+- 1db) or better, sensitivity (8 ohm stereo & 1khz) 1.0v Make- Martin Audio/ bitner/VAL/EV

Supply, Installation, testing & Commissioning of Slim Line Gooseneck Microphone With Polar pattern Hypercardioid Frequency range 50 to 19,000 Hz or better, Sensitivity 5 mV/PA or better, equivalent noise level <21 dB- A, Signal/noise ratio (A-weighted) >73 dB Impedance<=200 ohms or better. Recommended load impedance>=2,000 ohms Supply voltage 12 to 52 V phantom power Connector 3 pin male XLR Complete as per the specifications. Make - Audio Technica/ Shure/ Beyerdynamic EV.

Supply, Installation, Testing & Commissioning of Equalizer & loudspeaker Controler with Input Active Balanced, 10K ohms or better Crossover High-Pass Filter Type Linkwitz Key, Bessel, Butterworth Max Input Level +20dBu or beter Crossover High-Pass Filter Slope 12, 18, 24dB/Octave or better, Input and Output Gain Range +12/-40dB, 0.1dB Incr Crossover High-Pass Filter Range Off to 20KHz, Active Balanced, 110 ohms, EQ Filters 6 per input/ 4 per output or better, Compressor/Limiter Range 20hz to 10.6Khz, Parametric EQ Bandwidth 1/64th Octave to 4 Octave Input AD System complete as per the specifications AShley Yamaha/V-Tech /EV

Supply, Installation, Testing & Commissioning of Blue Ray DVD Player of Professional Grade with Dolby® True HD decoding (2Ch) ,DTS DTS-HD Master Audio decoding (MA),Video Output (BD-ROM) Yes (480i/ 480p/ 720p/ 1080i/ 1080p (60Hz)) Yes (576i/ 576p/ 720p/ 1080i/ 1080p (50Hz)) Power Voltage 110-240V Dolby Digital output and as per the specifications, complete as required Make Sony Panasonic/ LG.

Supply, Installation, Testing & Commissioning of Equipment Rack to accommodate all the AV Equipments, Front Lockable Glass Door, Rear Lockable Glass Door, 12 U size, Power Strip with blower complete as per the specifications. Make: President/VAL Rack/E-Learn.

Supply, Installation, Testing& Commissioning of HDMI (Male to Male ) Cable with lenth of 1 mtr supporting the resolutions 480i, 480p, 720p, 1080i, 1080p.

Supply, Installation, Testing & Commissioning of HDMI (Male to Male) Cable with lenth of 5 mtr supporting the resolutions 480i, 480p, 720p, 1080i, 1080p.

Supply, Installation, Testing & Commissioning of Moulded VGA ( Length 1 mtr) Cable Subcategory Audio, Display Connectivity Left Connector Type: 15 pin HD D-Sub (HD-15) Mini-phone stereo 3.5 mm Connectivity Right Connector Type 15 pin HD D-Sub (HD-15) , Mini-phone stereo 3.5 mm I/O Cable Type: VGA / audio cable Left Connector Gender Male Right Connector Gender: Male.

Supply installation, Testing & Commissioning Desktop, Microphone stand with adjustable height adjustment.

Supply, Installation, testing & Commissioning of Shielded Twisted Pair Cable, Conductor Metal: Solid Bare Copper with 24AWG Color Code: Bluel/ Grey (or any combination) Jacket Material: PVC UL94V-0 complete as required.

Supply, Installation Testing & Commissioning of RGBHV Cable, muiti-conductor containing 3 mini coaxes, 2 shielded pairs, and 7 single strands 26AWG center conductor and dual shield design consisting of copper braid and aluminu Mylar foil.

Supply laying, Testing & Commissioning of Speaker cable Stranded 2 X 1.5 sq mm, PVC insulated and soft sheathed copper low loss, low conductance.

supply, laying, testing & Commissioning of Micropnone Cable with high-quality shielded pair for routing balanced mono or unbalanced stereo mic stranded 20AWG tinned Copper.

Connectors including XLR, Phono, Speakon, VGA, BNC etc.

Ceiling Mounted Brackets for speakers.

Supply , Installation, Testing & Commissioning of RGBHV cable multi-conductor containing 3 mini coaxes, 2 shieilded pairs, and 7 single strands, 26AWG center conductor and dual Shield design consisting of copper braid and aluminum Mylar foil.

Supply, Installation, Testing & commissioning of Cable Cubby with pneumatic movement and mechanical latching mechanism, Compact size with rectangular bezel, Top surtace in black anodized finishes, One CAT 6 RJ-45 nework/Data/Phone connectors, One unswitched AC Outlet, One Data input on HD 15 Connector, One input on HDMI One input for S-Video. Approved Make Extron-HSA 300/ Altinex equivalent/ Crestron equivalent.

Supply, Installation, Testing & commissioning of 3 input SWitcher with 1 x HDMI, 1 x VGA , 1 X DP Inputs and scalled Output on HDMI port , Auto source detector. Approved Make Kramer-VP 461 /Extron equivalent/ HPC equivalent.

SUB HEAD-XVI - EARTHING SYSTEM

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required..

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required..

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as requiredt.

Providing and fixing 8 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required..

SUB HEAD-XVII - FIRE DETECTION AND ALARM SYSTEM

Supply and fixing of Single Loop addressable control panel with LCD Display, Loop Driver card, lamp test frature,complete with integral power and bettery charger for sealed leaad acid battery, potential free contacts for both fire and fault, Short circuit, isolate, Fire in Nos Zone Complete in all respect.

Supply, Installation, Testing & Commissioning of Microprocessor based Multi sensors complete with MS Powder coated Junction Box for mounting on Surface, Cable lugs at Ends, cable compression glands, cable tags and Ferruling complete as per specification required.

Supplying, installation, testing and commissioning of Dual LED Response indicator for indicating the activation of the Remotely located Detector. Complete in all respect.

Supply, installation, testing and commissioning of Microprocessor based manual call point (Alarm Station MCP) , Complete in all respects.

Supply, Installation, Testing & Commissioning of Microprocessor based Wall Mounted Voice Evacuation Hooter cum Speaker of 2W having power taps at 1/4-1/2 complete as per specification required.

Supply, installation, testing and commissioning of Microprocessor based addressable control module for activating the hooter etc.complete as per required.

Supply, laying & testing of ISI Marked, FRLS Type, Flexible Unarmoured, Unsheilded Twisted Pair 2 Core x 1.5 sq. mm, Multistranded Copper Cable with all necessary accessories for termination at devices, laid through existing 25mm MS Conduit etc. complete as required.

SUB HEAD-XVIII - EXTERNAL ELECTRICAL WORKS

Supply ,installation, testing and commissing of 415 Volt, 3 Phase, 4 wire , 50 Hz , IP-65, Free Standing Floor mounted out Door Panel , made out of 2mm thick CRCA sheet for main frame and 1.6 mm thick for partions after seven tank process and painting with Epoxy powder coating. including all switchgear as detailed below. this panel shall consist of suitable rating TPN aluminium bus bar ( at the rating of 0.8/sqmm) supported with DMC/ SMC barriers and colour coded with Heat Shrinkable Sleeves. The metering shall be provided as specified. This Panel shall have short circuit with standing capacity of minimum 50 KA and consist of the switchgear as mentioned below. this panel shall be mounted on channels including supply of the same.This panel shall be got fabricated from manufactures CPRI test certificate only. this panel shall have at least two spare cubicles of maximum ratings. The size of all panel mounting meters shall be as per Suitable Design. Incoming -

CABLE WORK Supplying & laying of LT Aluminium conductor Power Cable of following sizes, 1100 volt grade XLPE insulated , PVC inner sheated, galvanised steel strip or wire armoured cable as per IS 7098(PART 1)1988. 3.5 core 300 Sqmm (a) Laying direct in ground including excavation, sand cushioning, protective covering by bricks and refilling the trench etc as required.

Laying and fixing on wall surface in existing RCC/ HUME/ METAL pipe as required.

3.5 core 150 Sqmm (a) Laying direct in ground including excavation, sand cushioning, protective covering by bricks and refilling the trench etc as required.

Laying and fixing on wall surface in existing RCC/ HUME/ METAL pipe as required.

3.5 core 95 Sqmm (a) Laying direct in ground including excavation, sand cushioning, protective covering by bricks and refilling the trench etc as required.

Laying and fixing on wall surface in existing RCC/ HUME/ METAL pipe as required.

2 core 35 Sqmm (a) Laying direct in ground including excavation, sand cushioning, protective covering by bricks and refilling the trench etc as required.

Laying and fixing on wall surface in existing RCC/ HUME/ METAL pipe as required.

2 core10 Sqmm (a) Laying direct in ground including excavation, sand cushioning, protective covering by bricks and refilling the trench etc as required.

Laying and fixing on wall surface in existing RCC/ HUME/ METAL pipe as required.

CABLE END TERMINATION Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 X 35 sq. mm

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 300 sq. mm

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 150 sq. mm

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 95 sq. mm

SUB HEAD-XIX- ROAD WORK

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

"Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing 25mm dia dowel bars with sleeve @ 600mm c/c tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints ( 10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, tie bars to be paid separately). Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. (a) Cement concrete prepared with batch mixing machine

Supply & Laying of Polyvinyle chloride sheet 400 micron as directed by Engineer incharge.

Providing and fixing in position pre-moulded joint filler in expansion joints.

Providing and laying in position bitumen hot sealing compound for expansion joints etc. (a) Using grade 'A' sealing compound.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.

Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading, well ramming, consolidating and grouting with fine sand, including finishing smooth etc. complete as per direction of Engineer-in-charge.

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. (a) With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

SUB HEAD-XX - FURNITURE

Supplying and placing in position Conference table of the following Nos. specifications. 20 Seater Boat Convex size shall be 6000 Width mm X 1200 Depth mm X 750 Height mm. Top shall be 32 mm thick base material shall be 18 plus 12 mm MDF board 0.4 mm PVC membrane foil using wrap around technology. The foil is pre -coated with PU layer for better scratch and wear resistant plus 0.6 laminate on bottom surface. The vail and cross member shall be 18 mm thick base material shall be 16 mm plain particle board post laminated with 0.6 mm top laminate on either side plus 2 mm thick and 0.8 mm thick PVC edge banding. The legs shall be made from 1.6 mm matt silver anodized aluminium extrusion. Legs assembled togher with a plastic glide holder at bottom and 5 mm thick MS power coated sheet at top. Also there shall be access flap and swith mounting tray made from matt anodized aluminium extrusion.

Supply of officer Table of Size 1800 X 900 X 750 mm high made out of 19 mm thick commercial block board finished with 3.5 mm thick teak veneer of approved quality on top,Sides & front having 3 drawers running on telescopic channel and with locking arrangement for one drawer, all exposed edges to have teak wood lipping. Foot rest of teak wood of size 65 X 30 mm including inner surface and all exposed wooden surface finished with two or more coat of spirit polish including wood filler etc all complete.

Supply of Office Table of size 1500 X 750 X 750 mm made out of 19 mm thick commercial board with 1 mm thick laminate on Sides, front, back & top of approved shade & quality, 3 drawer (front with 19mm thick commercial block board, sides with 12 mm thick commercial ply and bottom with 4 mm thick commercial ply) running on telescopic channel and locking arrangements for one drawer. All exposed edges to have teak wood lipping, foot rest with teak wood of size 65 x 30 mm, Inner and exposed wooden surface finished with melamine polish and provided with 6 mm thick plain edge polished glass etc. all complete.

Supply of Centre Table of sizes 1050 x 525 x 450mm made out of teak wood frame, side with 70 x 25 mm teak wood and 45 x45 mm teak wood decorative legs, top with 19mm thick commercial board and 1mm thick laminate including 20 x20 mm teak wood moulding all exposed surfaces with two or more coats of spirit polishing including wood filler.

Supply of Corner Table of size 600x600x400 mm made out of teak wood frame, side with 70 X 25 mm teak wood and 45 X 45 mm teak wood decorative legs, including 20 X 20 mm teak wood moulding all exposed surfaces with two or more coat spirit polish including wood filler etc all complete.

Supply & placing in position Reception Counter 1800mm long having double top ,600mm up to 75Omm high and 300 mm at 1150mm, top to be finished with approved quality of laminate made out of 19mm thick one side teak board with 1 drawer and 1 cabinet of Nos side and provided 1 shelf finished with laminate edges covered, finished with two or more coat of spirit polish including wood filler etc all complete. as per design and as per standard specifications & directed by Engineer-in-Charge.

Supply of Executive revolving and tilting high back chair of size 560 x 590 x 1100 mm having moulded 12 mm hot pressed ply and 50 mm thick high density PU seat and back fixed on 15 mm dia steel tubular frame covered with 35 mm thick foam on both sides fully upholsted with fabric/leatherite of approved shade/colour alongwith rubberrized PU arms mounted on five castors pedestal wheel with gas lift mechanism all complete.

Supply of revolving and tilting executive Medium Back Chair of size 515 X 515 X 800 mm high having moulded 12 mm hot pressed ply with 60 mm thick high density PU seat and back fixed on 15mm dia steel tubular frame covered with 35mm thick foam on both the side fully uphlstered with Fabric/leatherette of approved shade/colour along with rubberrised PU arms rest mounted on five castors pedestal wheel with gas lift mechanism all complete.

Supply of revolving Low Back Visitor Chair of size 425 X 460 X 800 mm high having moulded 12 mm hot pressed ply with 60 mm thick high density foam on seat and back covered with approved quality of fabric alongwith full arms mounted on five castors pedestal all complete.

Supply of revolving Computer Chair without arm of size 510 X 410 X 800 mm high, moulded 12mm hot pressed ply with 50 mm thick rubber cushion set & back upholstered with fabric of approved quality, mounted on powder coated five twin castors hydraulic gas lift pedestal etc. all complete.

Supply of Sofa made out of 50 X 25 mm second class hard wood frame and upholstered 100 mm thick rubber foam fully upholstered with fabric of approved colour including arms of teak wood with melamine polish etc. all complete as per approved sample. (a) Single Seater

Supply of Sofa made out of 50 X 25 mm second class hard wood frame and upholstered 100 mm thick rubber foam fully upholstered with fabric of approved colour including arms of teak wood with melamine polish etc. all complete as per approved sample. (a) Double Seater

Supply of Notice Board of size 900 X 600 X 100 mm made out of 19 mm thick one side teak face block board having teak- wood frame shutter with 4 mm thick glass and blazer cloth on background, all exposed edges to have teak wood beading including necessary hardware fittings and with two or more Coat spirit polish including wood filleretc complete.

Supply and fixing of Drapery rods of 25mm dia including rings brackets with all fixtures and fittings as approved

Providing and fixing beveled edge mirror of superiorglass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Supply of powder coated Steel Almirah large of Size 1980 X 910 X 480 mm made out of 18 Gauge M.S. Sheet with 4 shelves (making 5 compartments) With locking arrangement including duplicate key as per approved colour etc. all complete.

VASTU SHOBHA