PROVN OF SHED AND CONNECTED WORKS AT BLDG 18/19 AND CERTAIN MINOR WORKS UNDER ZONE-I AND ZONE -II AREA AT JAIPUR MIL STN

Amount

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and raming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface

M&L Cement concrete in foundations, filling and mass-concrete in PCC 1:2:4Type D-2 (using 40 mm graded stone aggregate) complete all as directed.

M&L Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates.

M&L Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Preparation of new steel & iron surfaces & applying two coats of synthetic enamel paint over 10 cm width or girth etc. complete all as directed.

M& L Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc. complete all as directed.

S & F powder coated aluminium sections for doors, windows, ventilators, door partition including fabrication of frame shutters including two or three track as required and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc. including all accessories such as glazings clips, and rubber beadings for fixing glass panes in frame complete all as specified. Note : (i) Glass panes will measured & paid separately . (ii)The quoted rate shall be inclusive of cost of rubber beading however it will be not be weighed and paid separately.

S&F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples fixed in repair in wooden doors and steel windows complete all as directed.

M&L Anodised aluminium door shutters power coated ,as a fixed frame, sliding frame, any type aluminium section weighing 0.55kg/m including necessary joining cleats,including glazing clips, rubber packing, roller anodised alumnium snap beading, screws etc. complete all as specified

M&L Aluminium grill of standard section, type'A"diagonal with U rail necessary joint jointing cleats, glazing clips rubber packing, anodized aluminium snap beading, screws etc complete all specificed and directed.

M&L for 5.5 mm thick plain sheet glass, ordinary quality and glazing with aluminium beads and rubber gaskit in square exc 0.5 sqm in each pane frosted on one side complete all as specified and directed.

M&L for 5.5 mm thick antilo sheet glass,colour glass ordinary quality and glazing with aluminium beads and rubber gaskit in square exc 0.5 sqm in each pane frosted on one side complete all as specified and directed.

M&L for 12 mm thick plain sheet glass, colour glass ordinary quality and glazing with aluminium beads and rubber gaskit in square exc 0.5 sqm in each pane plete all as specified and directed.

M&L 12mm thick pre-laminated particle board, flat pressed single layer type or three layer type with BWR type adhesive, medium density interior grade having both side decorative lamination and other side balancing white lamination as in cup board shutter including 6 mm thick teak wood leaping on three sides and 20mm thich on hanging side & French polishing to edging complete all as specified.

M&L for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless stell cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

Supply & fix 100 mm size butt hinges, heavy weight, cold rolleda luminium alloy complete all as specified and directed.

Supply & fix 200 mm length aluminium anodised barrel tower bolt extruded section complete all as specified and directed.

Supply & fix 300mm long aluminium alloy, anodised sliding door bolt with haps, staple(bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

Mortice lock, vertical type, size 100 mm brass 4 lever all as directed.

S&F aluminium (extruded section) body door closer hydraulically regulated designation No 3, universal type,suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80 kg complete all as specified and directed.

Providing precast cement concrete louvres and jallies, 25mm thick (measured solid), including all mouldings but excluding frame (pre cast frame shall be measured separately and paid for under item)

Excavation in trenches not exc. 1.5 mtr wide and not exc. 1.5 mtr depth for cesspits, manholes etc. and getting out soft/loose soil even in foul position complete aii as specified and as direcetd.

Returning, filling including spreading leveling watering and well ramming in layers n. exc 25 cm in soft/loose soil complete all as directed.

Removing excavated soil to a distance n. exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as directed.

M&L Brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., omplete, drilled for fixing of steel sheeting or other covering. Doors, etc. to e prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening complete all as directed.

S&F central hole wash basin mixer 15mm dia with 450mm braided connection pipe of make Cera Cat Part No F2007461 or equivalent as approved by GE

S&F corner glass shelf large 300mm x 300mm complete all as specified. Make - CERA Cat Part No F5005103 or equivalent as approved by GE

S&F CP brass Towel rail Make - F5001103 of CERA or equivalent as approved by GE

S&F CP brass Towel ring Make - F5004105 of CERA or equivalent as approved by GE

Supply & fixed mild steel curtain rod powder coated with fixing side brackets, end cups, rings @ 10 Nos per RM and fixed with PVC rawl plugs & steel screws complete all as specified and directed.

S&F in repair Vitreous China one piece EWCs with seat cover and twin flush fitting snow white colour of size 690 mm x 380 mm x 780 mm (Cat Part No S1013123 of CERA or equivalent as approved by GE), etc complete all as specified and directed.

S&F in repair toilet paper holder Make Cera Cat Part No F5007110 or equivalent as approved by GE

S&F in repair Vitreous China snow white wash basin, Canton pattern size 615 mm x 510 mm with pedestal , 32 mm dia CP waste coupling & 25 mm dia, 75 cm long PVC waste pipe with 32 mm dia connector of make Cera Cat Part No S2040122 & S2090107 or equivalent as approved by GE

M&L for complete removal of existing treatment and applying two coats of oil bound distemper over a coat of water based primer over 3mm thick (average) wall care putty applied in two coats including rubbing with suiatble table sand paper complete all as specified.

M&L for preparation of new plaster surfaces of walls and applying two coat of oil bound distemper over a coat of primer complete all as specified

M&L for preparing new plastered surfaces of walls and applying two coat of cement based paint complete all as specified

Material and labour rendering 15 mm thick cement plaster in CM 1:4 on other than fair faces of brick/concrete work surfaces mixed with integral water proofing compound finished even and smooth (without using extra cement ) all as per manufacturer's instruction and as specified.

Rendering 15 mm thick on brick masonry surfaces in CM(1:6) finished even and smooth with out using extra cement

S & F stainless steel 304 grade retro reflective board of size 1.20m x 0.90m, written on both side (2 pieces ACP sheets required for writing both side). The board made out of 3mm thick ACP sheet shall be shealted with reflective tape of blue colour high intensity plastic (HIP) 3m, letter shall be written in colour and size as approved by GE The board shall be fixed on SS post 63mm dia 16 gauge 304 grade of length 2.1m out of which 0.45m shall be embedded in PCC all as specified and directed by Engineer-in-Charge. Note :- Quoted rate shall be deemed included the cost of PCC and earth work required for above.

M&L coloured Non Skid joint free ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set over 15mm thick screed in CM 1:6 and jointed in neat cement slurry and pointed in white or coloured cement to match

Preparation of old wooden or wood based surfaces of any description, over 10cm width or girth and applying a coats of synthetic enamel paint complete all as specified and directed.

M&L for preparing old steel surfaces of any description not otherwise described over 10cm in width or girth and applyingapplying one coats of synthetic enamel paint complete all as specified

S&F fancy type Hand shower70 mmdia with hook and 1.5 meter hose1 Long Make -CERA Cat Part No F7030301 or equivalent as approved by GE

S&F fancy type Health faucet 15 mm bore (ISI marked) including extension Pipe of 1 Mtr Long Make -CERA Cat Part No F8030103 or equivalent as approved by GE

M&L preparation of new steel surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer all as specified and as directed.

M&L PCC 1:4:8 Type D2 (40 mm graded aggragate) as in fdn, filling and mass concrete.

M&L rendering 15mm thick on other than fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement.

M&L two coat of oil bond distemper over one coat of putty including preparation of newly plaster surface

M&L PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in retaining walls, any thickness, size or shape including pilars, buttresses columns, boundary pillars and post, foundation filling and mass concrete for sub base etc complete all as directed. .

S&F MS work as in fencing post, blausters etc, angle iron, flat iron, flat iron round or square bars including all necessary cutting, drilling holes in flat iron, bolting etc for screwing chain link fencing all as directed

S&F screw bolts (machine made) with hexagonal or square head at one head and rounded the other or screwed both end each screwed end to be fitted with washers and one hexagonal or square nut exc 10cm nexc 15cm long dia of shank 11 to 15mm.

S&F mild steel round bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for chain link fening ( in new or old ) complete all as directed

Supply only chain link fencing 4mm dia galvanized steel 50mm x 50mm mesh fixed to angle iron fencing post or angle frame complete all as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as directed

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire 0.9 mm dia complete all as directed

S&F 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with coarch screw and washer in roof wall and cladding etc complete all as directed

S&F light shade vetrified ceramic tiles edge cut 10mm thick ( square/ rectangular ) polished, area of each tiles not exceeding 0.36sqm in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 15mm thick screed bed in CM (1:4) finished fair and even complete all as directed

Surface dressing n exc 15 cm deep and site clearance for soft and loose soil complete all as directed.

M&L for sub main wiring along with earth continuity conductor with, PVC insulated FRLS multistranded copper conductor cable (Phase-Red, Neutral-Black, Earth-Green) drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour along with accessories 2x6 Sqmm + 1x6.0 Sqmm earth wire in 25mm dia conduit.

S&F LED (1.2M) smartbrite batten fitting made of extruded aluminium housing with quality polycarbonates diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficacy of 100 lumen per watt and total power consumption not more than 21 watt including driver having a color temperature of 6500K, CRI>80, THD<10% and PF>0.95wide voltage range 140V to 270 V (worm white) complete.

S&F LED (0.62M) smartbrite batten fitting made of extruded aluminium housing with quality polycarbonates diffuser duly prewired connection having a nominal system lumen output of 1150 lumens at a minimum system efficacy of 105 lumen per watt and total power consumption not more than 10 watt including driver having a color temperature of4000K, CRI>80, THD<10% and PF>0.95 wide voltage range 140V to 270 V (worm white) complete.

Supply and fixing ceiling fan 1200mm sweep 50 Hz AC 230 volts, 5 star rated in white colour with fan motor, blade set, 0.45 mtr down rod, canopy set, rubber reel including 0.5 Sqmm three core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling and wiring MES No on fan body as required. Make : Havells Model No ES-40 or CG ModeleSAVE50 or Orient Model - Ecotech plus or equivalnet as approved by GE

M&L for point wiring with 1100 volts grade PVC insulatd FRLS multistranded copper conductor cable 1.5 Sqmm (Phase-Red, Neutral-Black) and earth continuity conductor 1.5 Sqmm (Green) drawn into and including concealed rigid non metalic PVC conduit medium grade not less than 20mm dia ISI marked ivory colour with all conduit fitting/fixing accessories and galvanised pressed steel terminal boxes and including modular metal flush boxes 1.0mm thick, mudular frame and coer for mounting switches sockets, fan regulators as required for one light point controlled by one switch

All as per item No. 64 above but one fan point controlled by one switch.

All as per item No. 64 above but one socket outlet 6 Amps controled by one switch on the same board with other switches.

All as per item No. 64 above but one socket outlet 6 Amps controlled by one switch on independent board.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4.0 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings/fixingaccessories terminated in modular sunken boxes including mounting plates for mounting switches, sockets, fan regulator as required for one light point controlled by one switch. (Note - The cost of cutting chases in stone masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate of the concealed wiring)

S&F switch modular 1 way 6 Amp, 230 volts, 1 module.

S&F modular socket 6 Amp, 2/3 pin combined 2 module AC 230 volts.

S&F modular switch 1 way 16 amp, 230 volts, 1 module.

S&F modular socket 6/16 Amps, 2/3 pin combined 2 module AC 230 volts.

S&F modular fan regulator 120 watts, 2-module AC 230 volts.

S&F 25 amp single pole and nutral, socket outlet with 2 pole and earth, metal enclosed plug top in power coated CRCA steel enclosure recess mounted with chained metal cover for the socket outlet with and including one number single C seriese MCB 16 apm as required.

Supply & fix PVC wall mounted fan 450mm sweep AC single phase 230/240 V complete.

Schedule of Credit

NAGHAR ENTERPRISES

NARAYAN SINGH NARENDRA SINGH AND COMPANY

S.R.Enterprises

M/S ROHIT CONSTRUCTION

Smita Constructions

J.J.ENGINEERING

UNIVERSAL INFRAPROJECT PVT LTD

M/S S R CONSTRUCTION