COMPREHENSIVE/ WELCOME MAINTENANCE TO MD OFFRS ACCN AT DHAULADHAR ENCLAVE UNDER AGE B/R-I OF GE (N) MAMUN

Amount

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n.exc 1.5 sqm complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm and n.exc 4 Sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but n exc 2 Sqm each complete all as specified and directed.

Refixing shutters of any description after minor repair exceeding 1.00 Sqm and not exceeding 2.00 Sqm each in same opening, complete all as specified and directed.

Taking down cement plaster on brick walls or stone walls of any description etc including raking out joints, hacking for key, scrubbing down with water etc, rubbish off the premises, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness, below or above ground level, complete all as specified and as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for( reinforcement cut as required to facilitate demolition) and rubbish off the premises, complete all as specified and directed.

Demolition of brick work or stone masonay built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stonework and precast concrete articles and removal of debris/rubbish off the premises etc complete all as specified and directed.

Taking up or down steel tubing 15mm dia and connections, including cleaning for refixing or removal to store, complete all as specified and as directed.

Taking up or down steel tubing 20mm dia and connections, including cleaning for refixing or removal to store, complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed.

M&L for of Brass CP suitable for sink centre hot & cold water (as per sample) screwed down for 15mm bore dia of pipe & 450mm long iron pipe and fixed cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

PCC 1:5:10 type E-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

Brick work with fly ash (Old Size bricks) sub class 'B' bricks straight or curved on plan, exceeding 6m mean radius with old size bricks, built in cement mortar 1:6, complete all as specified and as directed.

Brick work with fly ash (Old Size bricks) sub class 'B' bricks straight or curved on plan, exceeding 6m mean radius with old size bricks, built in cement mortar 1:4, complete all as specified and as directed.

5mm thick rendering on concrete surface of ceiling, chajjas etc. in CM 1:3 finishing the surfaces even and smooth without using extra cement, complete all as specified and directed.

10mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6 finished the surface even and smooth without using extra cement, complete all as specified and directed.

15mm thick rendering cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:4) mixed with WPC finished even and smooth without using extra cement complete all as specified and directed. Note: WPC shall be measured and paid for separately.

10mm thick rendering on fascia / edging / ceiling of chajjas, roof projections etc, making the edges in line, in true shape in CM 1:3 and finishing the surface without using extra cement, complete all as specified and directed.

15mm thick rendering on brick work or concrete surfaces in CM 1:4 mixed with water proofing compound to sunken portion with proper slope towards outside, finishing cement concrete or brick work surface even and smooth using extra cement, provide 90 micron polythene film duly applying bitumen coating @ 3.00 Kg/Sqm complete all as specified and directed. Note: WPC shall measured and paid for separately.

20mm thick cement plaster in cement mortar 1:4 on brick or concrete surface of sunken floor finished even and smooth using WPC liquid as per manufacturer instruction @ 0.200 ltr in 50 Kg of cement incl raking out joints, hacking for key, scrubbing down with water etc, complete all as specified & directed.

Supply only liquid water proofing compound, complete all as specified and directed.

Liquid membrane water proofing treatment over existing RCC roof slab / chajjah / canopy / parapet walls etc to be executed through approved applicator of the membrane manufacturer with following specification complete all as specified and directed :- (a) Cleaning of dust, removal for all loose existing bituminous material manually with heat torch gun to get smooth plain finished surface, removing of vegetation/plantaion with no loose material on surface and treating the crakes upto 3mm width with single pack fibre glass reinforced crack filling compound of SMART CARE CRACK SEAL (ASIAN PAINTS) or equivalent as approved. (b) Repair all joints and cracks with highly elastic bituminous cold applied putty of tarplastic having penetration upto 8mm levelling of surface to give proper slope (after setting) with roof repair mortar i.e. cold applied Bituminous Mortar & cold emulsion cum waterproofing liquid, Created SSD condition on surface with water, prime the surface with liquid membrane waterproofing elastomeric monolithic acrylic emulsified water based bituminous coating with 200% elongation mixed with potable water in the ration of 1:1 and apply @400gm per Sqm (As per Surface Conditions) (c) Apply first coat of Liquid Membrane Waterproofing Elastomeric Monolithic Acrylic Emulshified Water based Bituminous Coating having elongation 200% conforming to ASTM-C-412, having cracks bridging of 8mm confirming to ASTM-C-836 with tensile strength after 7 days 0.50 mm conforming to ASTM-C-412 with no diluation of water on primed surface while the surface is still tacky with consumption of 700gm per Sqm, laying of Geotex of 45 GSM/ Fiber mesh simultaneously and paste it properly with overlap of 50mm & allow the first coat to dry for 10 to 12 Hrs .

(d) Apply 2nd coat on poured first coat with consumption @700 gm per Sqm in opposite direction of first coat by Brush or Roller and allow it to dry for 10-12 Hrs. (e) Ensure final curing time of 36 Hrs before allowing/ carrying out any further work. (f) Conduct ponding test after 7 days, continnue curing of 14 days. (g) Apply two coats of UV Resistant Elastomeric Exterior Axcrylic Weather risistant water proof coating having elongation of 300% confirming to ASTM-D-6083 for UV Protection of Bituminous Elastomeric Acrylic Emulsified Liquid Membranc to give life and prevent its deterioration from sunlight. NOTE :- (a) The Application of water proofing treatment will be executed by the authorised applicator only after necessary approval from GE. (b) All Shifting/ removing of any wire/cable/AC unit/Water tank of any capacity or other any object as per site requirement an re-fixing the same, if needed shall deemed to be included in the quoted rates by the contractor. (c) Removal of any loose/packed items such as mud phuska, terrace tiles, cement screed bed shall be removed and surface shall be made free from depressions before applying treatment to the roof. Quoted rates shall deemed to be included this fact into account and no extra payment shall be made on this account. (d) Contractor shall verify availability of the materials in full qty from market before quoting the rates as no extension of time on this ground shall be granted. (e) All the sample/ make for water proofing material mentioned in item shall be got approved from the GE before procuring bulk quantity of material.

Repair to old steel window exc 1 sqm but not exc 2.0 sqm including replacement of unserviceable/ damaged hinges, all handles, necessary welding to shutters and chowkhat for making window in serviceable condition, all members grinding to smooth surface and applying two coats of synthetic enamel paint over a coat of red oxide primer to grinded surface, complete all as specified and directed.

Repair to old steel window exc 2.0 sqm but not exc 4.0 sqm including replacement of unserviceable/ damaged hinges, all handles, necessary welding to shutters and chowkhat for making window in serviceable condition, all members grinding to smooth surface and applying two coats of synthetic enamel paint over a coat of red oxide primer to grinded surface, complete all as specified and directed.

Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed.

Factory Made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick wood grain moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and as directed.

Powder coated anodised aluminium door frame of section 101.60x44.45x1.60mm including powder coated anodised aluminium glazed door shutters (minimum thickness of powder coating 50 micron) having stile and top rail, lock rail and bottom rails of section 83.50x45mm, thickness of aluminium sections weighing not less than 0.588 kg/m having grooves for aluminium beading including necessary joining cleats, glazing clips, rubber neoprene packing, 125mm long stainless steel butt hinges- 03 Nos, 150mm long aluminium, anodised, barrel tower bolts of extruded section - 02 Nos, 300mm long aluminium alloy handles - 2 Nos, mortice lock, vertical type, size 65mm 4 levers-01 No, aluminium (extruded section) door closer hydraulically regulated designation No-3 , universal type , suitable foor door shutters of 851 to 1200mm in width and of weight between 61 to 80 kg-01 No and 5.5mm thick sheet glass in each door and anodised aluminum snap beading screws etc., complete all as specified and directed.

Powder coated anodised aluminium window frame three tracker sliding of section 101.60x44.45x1.60mm including openable powder coated anodised aluminium glazed window shutters (minimum thickness of powder coating 50 micron) with a provn of AC and aluminium grills having stile of section 49.910x44.45mm, thickness of aluminium sections weighing not less than 0.588 kg/m having grooves for aluminium beading lator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long-1 No, hinges type B-21 100mm long-2 No. suitable handle-1 No and 5.5mm thick sheet glass in each window, complete all as specified and directed.

Box type Steel windows and ventilators comprised of tubular frame and shutters made out of 1.25mm thick MS steel tube factory made with double side shutters wire gauged shutter & glass glazed shutter with side hung shutters with steel handle and steel peg stay dovetailed or welded including 2 Nos tower bolts 150mm long for each leaf and 10mm square bar grills at spacing as shown on drg welded to FI frame work, including other fittings, hinges, handles, tarred hold fasts, PCC blocks (1:2:4 type 12.50mm graded crushed stone aggregate) including 3mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples two coats of synthetic enamel paint over a shop coat of red oxide primer etc. all as shown on drg No CEPZ /TD-354/09 sheet 1/3 to 3/3 and making good to disturbed area in same finish, complete all as specified and directed.

Pressed steel frames for doors/windows of size size 125x60 mm (1.25mm thick MS sheet) with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, duly filling of cement concrete 1:3:6 type C-0 (using 12.50 mm graded crushed stone aggregate) to back of chowkhats, with a shop coat of red oxide primer and making good to disturbed area in same finish, complete all as specified and directed.

Pressed steel frames for doors/windows of size size 105x60 mm (1.25mm thick MS sheet) with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, duly filling of cement concrete 1:3:6 type C-0 (using 12.50 mm graded crushed stone aggregate) to back of chowkhats, with a shop coat of red oxide primer and making good to disturbed area in same finish, complete all as specified and directed.

Pressed steel frames for doors/windows of size size 75x60 mm (1.25mm thick MS sheet) with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, duly filling of cement concrete 1:3:6 type C-0 (using 12.50 mm graded crushed stone aggregate) to back of chowkhats, with a shop coat of red oxide primer and making good to disturbed area in same finish, complete all as specified and directed.

35mm thick, 2nd class hardwood (Sal/ Hollock) factory made, plain framed, panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneers on both faces, the size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified and directed.

35mm thick, 2nd class hardwood (Sal/ Hollock) factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge,etc. with sash bars, edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter supplying and fitted to chowkats, complete all as specified and directed.

S&F in repair 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts, complete all as specified and directed.

S&F in repair 18 to 20mm thick prelaminated PVC solid board with acrylic lamination interior grade, prelaminated with one side decorative choice lamination and other side balancing white lamination as in kitchen cabinet, cupboard etc fixed with screws to steel/timber frame work etc,complete all as specified and directed.

S&F in repair 18 to 20mm thick prelaminated PVC solid board with acrylic lamination, interior grade, both sides prelaminated with white lamination as in kitchen cabinet, cupboard etc fixed with screws to steel/timber frame work etc,complete all as specified and directed.

5mm thick factory made single extruded WPC board, one side prelaminated sheet for kitchen cabinet/cupboard of density 600 kg /Cum, 90° bent, complete all as specified and directed.

S&F in repair 100mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.

S&F in repair 200mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

S&F in repair 150mm long, stainless steel brignt finish handle fixed with nut and bolt /screws, complete all as specified and directed

S&F in repair 150mm long, extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed.

S&F in repair 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

Hasp and staple, safety type, mild steel , wire type stove enamelled black, including bolt to hinge plate and fixed with screws, complete all as specified and directed.

Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, 30mm width of flap when open, complete all as specified and directed.

Floor door stopper of aluminium alloy body and tongue, anodised, 150mm length of cover plate with hard drawn steel spring, fixed in floor, complete all as specified and directed.

S&F in repair Telescopic type side channel of drawer of standard size including roller for moving drawer made out of mild steel bright finish or electro-galvanised (soft close ball bearing runners) with width of flap 30mm & 60mm long complete all as specified and directed.

Stainless steel, 304 grade heavy duty, plain basket of size 17''x20''x6'', complete all as specified and directed.

Stainless steel, 304 grade heavy duty, partition basket of size 17''x20''x6'', complete all as specified and directed.

Stainless steel, 304 grade heavy duty, cutlery tray of size 17''x20''x6'', complete all as specified and directed.

Stainless steel, 304 grade heavy duty, cup & saucer tray of size 17''x20''x4'', complete all as specified and directed.

Stainless steel, 304 grade heavy duty, plate basket of size 17''x20''x6'', complete all as specified and directed.

Stainless steel, 304 grade heavy duty auto zero crank hinges, fancy type with concealed pattern, fitted to shutters complete all as specified and directed.

Magnetic catcher for shutter of approved pattern fitted with suitable screws, complete all as specified and directed.

Aluminium (extruded section body) door closer hydraulically regulated designation No-3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg, fixed in repair, complete all as specified and directed.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, fixed in repair, complete all as specified and directed.

Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples (fixed in repair),complete all as specified and directed.

S&F in repair 3mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed.

S&F in repair 3mm thick figured/frosted glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed.

S&F in repair 20mm bore stainless steel, single curtain/drapery rod (wall thickness not less than 1mm) including fancy type PVC brackets, fenials etc suitable for single curtain rod, fixed in repair, complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws including dismantling old sheet as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws including dismantling old sheet as specified and directed..

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.

MS TMT bars 10mm dia and over cut to length, bent to shape required, including cranking bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not les than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed.

MS TMT bars 6-8mm dia and over cut to length, bent to shape required, including cranking bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not les than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed.

Precast reinforced cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in CM 1:6 including necessary moulds/formwork, complete all as specified and directed. Note :- Reinforcement shall be measured and paid seperately under respective items.

Breaking/dismantling, cleaning of loose concrete, replacement of corressive reinforcement, filling plain cement concrete 1:1.5:3 type-A0 using 12.50mm graded crushed stone aggregate using approved bonding chemical at places like chajja, sunshades, roof projection, fascia, beams, columns etc including necessary scafolding, formwork etc complete all as specified and directed. Note :- Reinforcement steel shall be measured and paid for seperately.

PCC type C-1, 1:3:6 (using 20mm graded crushed stone aggregate) as in plinth protection 75mm thick laid in slope finished even and fair including making joints not more than 2.5 m (or as directed) and at corner, filled with bitumen 85/25 and sand in ratio 1:2 by weight complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed (joint free) in neat cement slurry and pointed in coloured cement over 15mm thick screed bed or bedding layer of mortar in CM 1:4 and dismantling floor, hearth or walls tilling and terrazo topping including cement mortar bedding (but not backing), rubish off the premises, complete all as specified and directed.

Glazed ceramic coloured tiles 600mm x 300mm x 7mm thick as in vertical surfaces such as skirting, dado etc set and jointed joint free in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles and dismantling floor, hearth or walls tilling and terrazo topping including cement mortar bedding ( but not backing), rubish off the premises, complete all as specified and directed.

10mm thick vitrified tiles, light shade (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm in floors etc. set and jointed joint free in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement mortar 1:4 to recieve the tiles and dismantling floor, hearth or walls tilling and terrazo topping including cement mortar bedding ( but not backing), rubish off the premises, complete all as specified and directed.

10mm thick vitrified tiles, light shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm as in vertical surfaces such as skirting dado etc set and jointed joint free in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles and dismantling floor, hearth or walls tilling and terrazo topping including cement mortar bedding ( but not backing), rubish off the premises, complete all as specified and directed.

18 to 20mm thick bhaislana zebra black marble work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including dismantling old complete all as specified and directed.

Round chamfering to the edges of marble n.exc 15mm wide on shelves complete all as specified & directed.

Steel water tubing, 15mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed

Refixing of old steel tubing 15mm bore and connection in old or new position (walls, ceiling or floors etc.) with new all fittings short pieces, complete all as specified and directed.

Steel water tubing, 20mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

Refixing of old steel tubing 20mm bore and connection in old or new position (walls, ceiling or floors etc.) with new all fittings short pieces, complete all as specified and directed.

Cutting chases for concealed water tubing, making good to facing where required, pointing in CM 1:3, cutting n.exc. 10cm in girth, complete all as specified and directed.

20mm ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed in repair, complete all as specified and as directed.

15mm bore bib tap, long nose, fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule (fixed in repairs),complete all as specified and directed.

15mm bore stop valve/angel valve, chromium plated cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union (fixed in repairs), complete all as specified and directed.

15mm bore concealed type stop valve/angel valve, chromium plated cast copper alloy with long shank and cup, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union (fixed in repairs), complete all as specified and directed.

15mm bore pillar tap, copper alloy with capstan head, chromium plated screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe (fixed in repairs), complete all as specified and directed.

Supply, fixing, jointing and testing, 20mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed in repair, complete all as specified and directed.

Brass CP centre hole basin mixer (single lever) for mixing hot & cold water screwed down for 15mm bore dia of pipe & 450mm long iron pipe and fixed cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in repair, complete all as specified and directed.

Wall mixer with overhead brass chromium plated telescopic shower rose 125mm size for mixing hot & cold water screwed down for 15mm bore dia of pipe with or without swivel joints and fixed in repair, complete all as specified and directed.

S & F in repair vitreous china, wash hand basin, white, flat back, of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets, complete all as specified or erecting stand including 32mm full threaded waste coupling and 32mm PVC waste pipe, complete all as specified and directed.

S & F in repair vitreous china squatting pan water closet, orissa pattern, size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, front or back inlet and foot rests, any pattern including cement concrete bedding, complete all as specified and directed.

S & F in repairs vitreous china wash down water closet pan "Pedestal" coloured including fixing bolts etc including PVC seat cover white with flat bottom including MS, CP or aluminium anodised hinge devices & making good to floor in cement mortar M-15 (1:2:4) type B-1 (using 20mm graded crushed stone aggregated, complete all as specified and directed.

S & F in repair 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets including 32mm dia PVC flush pipe of suitable size and making necessary connections to water supply pipe line and jointing to WC, complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts at both ends of length 450mm for hot and cold water, complete all as specified and directed.

S&F in repair 32mm dia PVC waste pipe for wash hand basin, urinal and kitchen sinks, fixed in repair, complete all as specified and directed.

32mm dia CP waste coupling (half or full threaded), fixed in repair, complete all as specified and directed.

15mm dia disc spindle, fixed in repair, complete all as specified and directed.

Plastic water closet seat cover for EWC pan, white of standard quality and mild steel chromium plated or aluminised hinging device, fixed in repair, complete all as specified and directed.

Rotational moulded polythylene 1000 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismanting of water tanks of capacity exc 500 ltrs but not exc 1000 ltrs and removing to store, complete all as specified and directed.

Rotational moulded polythylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismanting of water tanks of capacity exc 250 ltrs but not exc 500 ltrs and removing to store, complete all as specified and directed., complete all as specified and directed.

Sinks with drainage board made of 1mm thick stainless steel kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, fixed in repair, complete all as specified and directed.

Stainless steel kitchen plate rack of size 750 x 900mm not less than 1mm thick sheet thickness of approved make fixed with mild steel screw, fixed in repair, complete all as specified and directed.

Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges (fixed in repair), complete all as specified and as directed.

S&F in repair 125mm size brass chromium plated shower rose with or without swivel joints, any size including fixing to steel pipe of 15mm dia or union, complete all as specified and as directed.

Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, fixed in repair, complete in all respect as specified and directed.

S&F in repair Sheet glass shelf assembly 12cm wide consisting of 5.5mm thick glass with CP bracket guard and railing 60cm long including chromium plated brass screws and wooden or plastic cleats (fixed in repair), complete all as specified and directed.

Corner glass shelf assembly consisting of 5.5mm thick sheet glass size not less then 300x300x70mm with chromium plated brackets double guard and railing including chromium plated brass screws and wooden or plastic cleats (fixed in repair), complete all as specified and directed.

Stainless Steel, 304 grade, heavy duty, toilet paper holder with with lid and flash recessed type fixed with stainless steel screws, fixed in repairs, complete all as specified and directed.

Cleaning of water tank of capacity 500 litres to 1000 litres at existing position (at roof slab/ staging of single/double/triple story bldg), emptying stored water through wash outlet, cleaning and removing all sludge, scale and dirt, etc. from tanks and from the mouths of circulating pipes, washing the internal surfaces with bleaching powder including writing the date of cleaning on tank with white/black synthetic enamel paint in prescribed manner, complete all as specified and directed.

Cleaning of water tank of capacity 250 litres to 500 litres at existing position (at roof slab/ staging of single/double/triple story bldg), emptying stored water through wash outlet, cleaning and removing all sludge, scale and dirt, etc. from tanks and from the mouths of circulating pipes, washing the internal surfaces with bleaching powder including writing the date of cleaning on tank with white/black synthetic enamel paint in prescribed manner, complete all as specified and directed.

PVC Lid for water tank of Capacity 500 Ltr to 1000 Ltr, fixed in repairs, complete all as specified and directed.

100mm dia stainless steel grating, complete all as specified and directed.

PVC cabinet, 510x490x100mm with looking mirror, full openable door, fixed in repair, complete all as specified & directed.

110mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

75mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

110mm bore dia PVC (SWR) reducers, complete all as specified and directed.

110mm bore dia PVC (SWR) branch piece, double (double Y) equal or unequal with oval access door, complete all as specified and directed.

110mm bore pipe PVC (SWR) vent cowl and fixed, complete all as specified and directed.

75mm bore pipe PVC (SWR) vent cowl and fixed, complete all as specified and directed.

110mm bore dia PVC (SWR) bends, complete all as specified and directed.

75mm bore dia PVC (SWR) bends, complete all as specified and directed.

110mm dia PVC floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), fixed in repairs, complete all as specified and directed.

75mm dia PVC floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), fixed in repairs, complete all as specified and directed.

Preparation of old painted steel or iron surfaces of any description over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and as directed.

Preparation of new steel surface any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash,complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of wall and applying three coats of white wash,complete all as specified and directed.

Complete removal of existing treatment from wall surfaces plastered or unplastered and applying two coats of white wash, complete all as specified and directed.

Complete removal of existing treatment from ceiling surfaces and applying two coats of white wash, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying 2mm thick wall care putty and making the surface smooth & applying two coats of oil bond distemper paint over a coat of priming paint, complete all as specified and directed.

Complete removal of existing treatment from wall surfaces of any type/description viz. distemper, emulsion etc using mechanical means/grinder, cleaning surface to receive finish, stopping the holes/dipressions with one coat of wall care putty to obtain smooth, even surface and applying two coats of oil bound distemper, complete all as specified and as directed.

Preparation of new plastered or unplastered external surfaces of wall and chajjas and applying one coat of wall care putty and two coats of cement base paint over a coat of alkali-resistant priming paint, complete all as specified and directed.

Complete removal of old existing treatment of external surfaces of wall and chajjas and one coat of wall care putty and applying two coats of cement base paint , complete all as specified and directed.

Preparation of old painted wood or wood based surfaces of any description over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and as directed.

Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

S&F in repair one piece Vitreous china wash down water closet pan pedestal pattern with flusing cistern, (size 69x36x74cm) white including making connections to trap, and to flush pipe including plastic seat and cover (as per sample ) with Stainless steel or aluminised hinging device and fixed complete all as specified and directed.

kewal builders (BID ID -3423454)

M/S NARESH KUMAR SHARMA (BID ID -3423296)

WALIA ENTERPRISES (BID ID -3429672)

Nishikant Mahajan Govt Contractor (BID ID -3423208)

M/S CANTILEVER ENGINEERS (BID ID -3422471)

M/S DUGGAL CONSTRUCTION CO (BID ID -3429811)

malghotra construction co (BID ID -3422993)

SUBASH MAHAJAN (BID ID -3429933)