PROVN OF PRE FABRICATED SHELTER FOR COOK HOUSE, RATION STORE AND DINING HALL AT ATS BELAGAVI

Amount

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth in hard and dense soil for foundation etc or for shaft, wells, manholes, pier holes etc not exceeding 10 Square Metre on plan and not exceeding 1.5 m in depth and getting out complete all as specified and directed.

Returning filling in including spreading levelling and well ramming in layers not exceeding 25 cm in hard soil all as specified and directed.

Removing excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and directed.

M & L PCC 1:4:8, type D-2 using 40mm graded stone aggregate as in mass concrete, foundation filling etc complete all as specified and directed.

M & L Reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate nominal mix for foundation, including rafts, footings, foundation beams, plinth beam, bases for columns etc basement slabs, underreamed piles and mass concrete complete all as specified and directed.

M & L Reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate nominal mix for columns, pillars, piers, posts, and struts complete all as specified and directed.

M & L formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter fair finished flat surfaces complete all as specified and directed.

M & L formwork to sides of pillars, posts, struts, piers, columns and stanchions vertical or to batter fair finished flat surfaces complete all as specified and directed.

M & L Precast Reinforced cement concrete 1:2:4 type B-1using 20 mm graded stone aggregate as in cover slab set and jointed in cement mortar 1:4 including necessary formwork complete all as specified and directed. Note : Reinforcement steel shall be measured and paid seperately under relevant item of schedule

M & L TMT bars 10mm dia and over as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M & L TMT steel bars of 5mm and over upto and including 10mm cut to length, bent to shape required, including cranking, bending spirally in stirrups, spacers and binders and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S & F purpose made mild steel bolts, dia of neck exceeding 20mm & not exceeding 25mm with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 30cm long embedded in RCC complete all as specified and directed

S & F mild steel bolts, dia of neck exceeding 11mm & not exceeding 15mm, machine made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 5cm and not exceeding 10cm long complete all as specified and directed

M & L Structural steel of plates, Fe-410 W (Gde E-250) Quality-B, channels, square cut or notched (ordinary or counter sunk) forming holes with riveted, bolted or welded attachments all as specified and directed

M & L Plain Cement Concrete 1:2:4 type B1 using 20 mm graded stone aggregate for embedding M S PIPES or similar work all as specified and directed.

M & L Glazed and skeleton shutters 35mm thick, second class hardwood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats etc complete all as specified & directed

S & F Rolled Mild steel in Roof trusses (framed), trussed, purlins, rails and fastenings and heavy brackets framing including distance pieces, cleats etc Fe 410-W (Gde E-250) quality B all as specified and directed

S & F of Rolled section having Fe 410-W (Gde E-250) quality B as in main and cross beams, hip and jack rafters: hollow / solid section for columns, purlins where connected to common rafters and running rails and guides for sliding doors: fixed with angle cleats or other connecting plates all as specified and directed

M & L for preparation of new steel surfaces of any discription over 10 cm width or girth and applying two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified and directed

M & L Powder coated Aluminium snap grid (minimum 50 microns thickness powder coating) of size 605 x 605 mm with anodised aluminium angle of size 25mmx25mm x1.5mm thick and main & cross T of size 40mm x 25mm x 1.5mm thick for false ceiling including fixing of supporting hangers all as specified and directed . Note :Cost of hangers will be measured & paid seperately under relevant items of this schedule

S & F Hangers 6 mm dia GI (up to 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long complete all as specified.

S & F 12 mm thick Gypsum board of size 600 x 600 mm as in ceiling fixed with screws and finished with two coats oil bound distemper over a coat of self primer all as per manufaturers instructions complete all as specified and directed.

S & F pre painted glavalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of approved colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

M & L pre painted glavalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of approved colour having tensile strength of 550 Mpa as in ridges, roof overing/cladding to wall, fixed with self tapping screws as specified

M & L for Mild steel work a in hold fast, wind ties,bands, straps or similar small articles conforming to Fe410-0 or Fe 310-0 etc.complete all as specified and directed.

M & L for preparation of new steel surfaces of any discription not exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified and directed.

S & F Plain, galvanised, mild steel sheeting 0.63 mm thick, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

M & L for pre cast cement concrete block masonry in 1:3:6 type C1 using 20 mm graded stone agrregate as in solid blocks exceeding 10cm in width having minimum compressive strength of 50 Kilo Gram/sq cm as per IS 2185 (Part I) 2005 and set in cement mortar 1:4 complete all as specified

M & L Plain Cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary formwork straight or curved complete all as specified and directed. Note: Reinforcement if provided shall be measured and paid separately.

M & L Pre cast cement concrete block masonry in 1:3:6 type C1 using 20 mm graded stone agrregate, solid blocks not exceeding 10cm thick with plain or interlocking joints as directed having minimum compressive strength of 50 Kilo Gram/sq cm as per IS 2185 (Part I) 2005 and set in cement mortar 1:4 complete all as specified and directed.

M & L Rendering 15 mm thick cement mortar 1:4 on fair faces of brickwork or concrete wall surfaces finished even & smooth without using extra cement complete all as specified and directed.

M & L Rendering 10 mm thick cement mortar 1:4 on fair faces of brickwork or concrete wall surfaces finished even & smooth without using extra cement complete all as specified and directed.

S & F (Rigid poly urathene foam) PUF insulated panels 60 mm thick 40 Kilo Gram/m³ density, sandwitched between two sheets of 0.50 mm thick pre-painted galvansed iron sheet cladding on both sides having internal finish with ivory colour and external finish with camouflage pattern and tounge and groove joints at both verticle side, panels have locking arrangements with check nuts for joining of panels of each other also heat transmission coeficient all as per IS 661-2000 and IS 3792. Panels will be provided with additional reinforcement in form of suitable MS hollow section vertically and horizontally at suitable intervals on over all as directed. Make:- Cactus Profile Pvt LTtd / BNAL prefab Pvt ltd /UNIMIX/ Prestar. Note:- (a) Quoted rates are deemed to be included the cost of bolts, nuts and other jointiong materials/ arrangements, silicon sealant etc all as per manufacturer instructions (b) Vertical steel reinforcement provided will be measured and paid separately under relevant item of this schedule

M & L for preparation of external new plastered wall surfaces by scrapping / washing / cleaning and applying two coats of antifungal weather proof emulsion paint over a coat of self primer all as specified and directed.

M & L for preparation of new internal wall surface by scrapping / washing / cleaning and applying a thin layer of wall putty and applying two coat of oil bound distemper over a coat of self primer all as specified and directed

M & L for preparing New plastered wall surfaces by brooming down or by steel wire brushing , scrapping down and applying three coat of white wash complete all as specified and as directed.

M & L preparation of new plastered walls, pillasters, cornices surface , etc. & applying two coats of cement base paint over a coat of self primer all as specified and as directed.

M & L Plain Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in 75 mm thick plinth protection including finishing of concrete surface even and smooth without using extra cement all as specified.

M & L for hard core of broken stone aggregate of gauge not exceeding 63 mm, spread and levelled in layers not exceeding 15 cm thick, watered and well rammed to a true surface complete all as specified and as directed.

M & L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in 75mm thick sub base to flooring all as specified and as directed.

M & L PCC 1:2:4 type B1 Using 20 mm graded stone aggregate as in 25 mm thick floor for laying floor tiles all as specified and as directed.

M & L Vitrified ceramic tiles 9 to 10 mm thick (Square/ Rectangular) polished, light shade, area of each tile not exceeding 0.36 Square Metre, in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including cement screed bed 15 mm thick in cement mortar 1:4 all as specified and as directed.

M & L Non skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tiles exceeding 0.06 Square Metre but not exc 0.11 Square Metre in flooring etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including screed bed 15 mm thick cement mortar 1:6 all as specified and as directed.

M & L Coloured glazed ceramic tiles of size 300 x 450 x 7 mm thick as in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including backing coat 10 mm thick cement mortar 1:4 all as specified and as directed.

M & L for Plain cement concrete 1:2:4 type B-1, using 20mm graded stone aggragate as in 100 mm thick flooring finished even and smooth without using extra cement including spike rolling to surfaces or making impression of expanded material whilst the concrete is green all as specified and as directed.

S & F Pressed steel frames for doors 125 x 60 mm size, pressed out of cold rolled mild steel sheets of 1.25 mm thickness, one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed complete as specified and directed

M & L Flush shutters 35 mm thick for doors, solid core construction, with particle board core and plywood face panels, commercial type on both sides all as specified and as directed.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube all as specified and directed.

S & F factory made solid panel PVC moulded door shutter 28 to 30 mm thick (stiles) with 2, 4 or 6 raised panel design with 2 mm thick moulded PVC sheet on the front face and 2 mm thick plain colour PVC sheet on back face, with particle board core all as specified and as directed.

S & F Powder coated ( minimum 50 micron thick) aluminium frame for doors, windows, ventilators, fixed partitions etc., with one or more rebates including joining cleat for fixing etc., complete all as specified.

S & F Powder coated ( minimum 50 micron thick) aluminium window or ventilator shutters, sliding type without sash bar, aluminum section weighing 0.55 Kilo Gram per Running Metre including necessary joining cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws, roller wheels, Spring catcher, necessary packing material etc., complete all as specified and directed

Supply and fix sheet plain glass 5.5 mm thick, ordinary quality, in squares not exceeding 0.5 Square Metre for each pane, glazing with aluminium beading all as specified and directed

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or steel screws all as specified and directed.

S & F Aluminium anodised barrel tower bolts of extruded section 150mm size all as specified and directed.

S & F floor door stopper of aluminum alloy body and tongue, overall length of cover140 mm, anodised with hard drawn steel spring fixed in floor all as specified and directed.

S & F Aluminium anodised barrel tower bolts of extruded section 200 mm long all as specified and directed.

S & F Butt hinges 100 mm long, medium Weight, cold rolled mild steel all as specified and directed.

S & F Aluminium alloy, anodised sliding door bolt 300 mm long with hasp and stapple (bolt type) and fixing clips of sheet, cast of extruded section and fixing bolts and sliding bolts extruded sections or cast aluminium alloy all as specified and directed

S&F Aluminium alloy, anodised handle, fabricated type 150 mm long all as specified and directed.

Supply and fixing harrison rails, mild steel chromium plated with fixing brackets, stops roller etc. all as specified and as directed.

M & L Precast cement concrete 1:2:4 type B0 using 12.5 mm grade stone aggregate as in louvres and jallies, 25mm thick (measured solid), including all mouldings but excluding frame set in cement mortar 1:4 all as specified and as directed.

M & L Preperation of new wooden surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

Supply & Fix Vitreous China Squatting pan, "Orissa" pattern, size 580 x 440 mm white with integral foot rests and including PVC Flushing cistern, low level, 10 litres apacity valve less, Syphonic action type, white with inlet, ball valve, float and handle with brackets, PVC Flush pipe 32 mm dia. 1.3m long, and setting the trap and pan in lime concrete bedding complete all as specified and directed.

S & F in Vitreous china wash down water closet (Pedestal), white including PVC Flushing cistern, low level, 10 litres capacity valve less, Syphonic action type, white with inlet, ball valve, float, handle, brackets including PVC Flush pipe 32 mm dia., Plastic seat of same colour of WC, closed pattern with flat bottom, and cover and Mild steel chromium plated hinging device, Health Faucet (ABS Body) mild steel chromium plated 15mm pipe dia-1.25 m long flexible tube and ABS wall hook including making connections and fixed in position in all respect complete all as specified and directed.

S & F Vitreous china urinal, bowl type (flat back or corner wall type) of minimum size 465 x 355 x 265 mm white with grating and union for discharge pipe, providing and fixing plugs, waste pipe, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified and directed.

S & F Vitreous China Ware Wash hand basin white, flat back, size 580 x 450 mm size by cutting for and pinning in ends of brackets including 15 mm bore pillar tap, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold, Waste fitting 32 mm dia. brass, chromium plated with PVC pipe complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 450mm all as specified and directed.

S &F CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed for the following :-

20 mm dia pipe

25 mm dia pipe

S & F brass Chromium plated shower rose 125 mm size with or without swivel joints including fixing to steel pipe or union all as specified and directed.

Supply and fixing soap dish of stainless steel fancy type fixed to walls with chromium plated brass screws complete all as specified and as directed.

S & F Bib taps 15mm, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified and directed.

S & F tubular brass chromium plated Towel rail 20 mm dia D type 60 cm long between flanges all as specified and directed.

S & F Stop valves fancy type, chromium plated, screwed down, high pressure, with crutch or round handle screwed bolts ends for iron pipe or for unions 15mm dia all as specified and directed.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints 75 mm dia fixed in wall/ floor all as specified and directed.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints 110 mm dia fixed in wall/ floor all as specified and directed.

S & F PVC (SWR) vent cowl suitable for 110 mm dia pipes all as specified and directed.

S & F PVC (SWR) Junction (single T) equal or unequal with access door 75 mm bore pipe all as specified and directed.

S & F PVC (SWR) Junction (single T) equal or unequal with access door 110 mm bore pipe all as specified and directed.

S & F PVC (SWR) bends 75 mm bore of any radius with access door all as specified and directed.

S & F PVC (SWR) bends 110 mm bore of any radius with access door all as specified and directed.

M & L Cement concrete 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in benching and forming channel inside manholes, surface channel, drains including finished smooth and even without using extra cement all as specified and directed.

S & F High density polyethylene Pipes (HDPE) 40 mm Dia bore of pressure rating 6 Kilo Gramf/cm2 fixed complete to walls, ceilings or in floors etc.,all as specified and as directed.

S & F PVC (SWR) floor trap 75 mm dia outlet, plain with grating including jointing to existing pipe properly with solvent all as specified and directed

S & F Ordinary rat tail rod pattern springs 300mm mild steel including roller and roller plate fixed to M S frame or wooden frame complete all as specified and directed

S & F aluminium powder coated fancy grill of thickness 4mm to 5mm, fixed to aluminium section all as specified and directed

M & L Reinforced cement concrete 1:1.5:3 type A1 using 20 mm graded stone aggregate nominal mix as in slab supported on walls, beams, deck slab and in shelves or similar items complete all as specified and directed.

M & L Machine cut cuddapah stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing machine cutting laid over and including 20mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Material and Labour for point wiring with PVC unsheathed multi stranded 1.5 Sqmm FRLS copper Cable drawn in and including PVC casing capping of suitable size complete with all accessories including MS sheet metal box 1.2mm thick switch board including PVC unsheathed multi stranded 1.5 Sqmm FRLS copper Cable as earth continuity connected with common earth dolly complete all as specified & directed for following:-

One light point controlled by one, one way switch 5 Amps

One fan point controlled by one, one way switch 5 Amps complete

One 3 pin switch socket outlet 5 Amps independent

Material and Labour for point wiring with PVC unsheathed multi stranded 2.5 Sqmm FRLS copper Cable drawn in and including PVC casing capping of suitable size complete with all accessories including MS sheet metal box 1.2mm thick switch board including PVC unsheathed multi stranded 2.5 Sqmm FRLS copper Cable as earth continuity connected with common earth dolly complete for 3 pin socket outlet 15Amps independent all as specified & directed

S&F switch piano flush button single pole one way 5 Amp 240 Volt

S&F switch socket combination 2 in 1, 3 pin 5 Amp flush type 240 volts complete all as specified

S&F switch socket combination multi purpose 3 pin 5/15 Amps universal type complete all as specified & directed

S&F complete for ceiling rose surface backelite three terminal 240 volts complete all as specified

Supply & fix ceiling fan complete with blades, down rods, electronic regulator and accessories 1200 mm sweep, minimum air delivery 210 CFM, with service value 6.00 BEE, five star, 32 Watts, 230 volts, Fan speed 350 RPM and BLDC technology including electric connection from ceiling rose to connector with flexible cord twin core twisted copper of size 23/0.0076 and fan hook made up of MS round bar no less than 16 mm dia and testing complete including all accessories all as specified and directed

S & F MCB Single Pole Neutral 6-32 Amps 240 volts, 50 Hz AC supply complete all as specified

S&F complete for MCB Single Pole 6-32 Amps 240 volts, 50 Hz AC supply complete all as specified

S & F Ceiling recess/surface mounting 28 W ( 3400 System Lumens ) luminaire 2'x2' enviromental freindly, new generation, asthetically designed ultra modern with high brightness SMD LEDs as light source, suitable for size 600x 600 mm all as specified & directed Make:- Havells cat No.PLUTONEO2X2PLR28WLED840S or equivalent make specified in P S

S&F sheet metal enclosure Distribution board SPN 12 Ways, double door, factory made , 240 volts with 200 Amps rated bus bar complete all as specified and as directed .

Supply & fixing LED LUMILINE 9/10 watt, surface and wall mounted LED batten with polycarbonate housing, ultra slim with housing and integrated electronic driver all as specified and directed. Make:- Havells cat No LUMILINEBS9WLED865SPCWH or equivalent make specified in P S

Supply and fixing of new generation saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 of 25 Watt with fixing arrangement such as sutable size of GI pipe not less than 1.5 mtr long, bracket, MS clamp, Nut bolts etc and connecting complete all as specified and directed. Make:-Havells cat Part No ENDURAPEARLSL25WLED757SASYTOPCMP or equivalent make in Crompton/Bajaj/Havells/Philips.

Supply and Fix Batten & LED tube 1x 20 w, decorative luminaire with CRCA housing,Ultra bright glass, very high efficacy suited for T5/T8 fitting with lamp holders etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size all as directed. Make & Model No for Batten :CROMPTON Cat No DIJB12LT8-20 and LED Lamp Cat No LGT8-20-865-2 or equivellent make as specified in P S

Material and Labour for Earthing with galvanized iron earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 M below normal ground level with top edge of earth plate at a depth not less than 1.5 M below normal ground level connected to and including G I wire 4 mm as earth lead by means of bolts and nuts, check nuts and washers etc made of GI & connected to equipment and earthing test point , earth dolly all as shown in elect plate No 3 of SSR Part-I including all necessary earth work, excavation PCC chamber, RCC 1:2:4 cover with handle, 20mm dia GI watering pipe, 40 mm dia light grade GI for protection of earth strip ,wire mesh, funnel, charcoal dust & common salt and testing etc complete all as specified and directed.

S&F sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 2 Way scomplete all as specified and as directed .

S & F exhaust fan, single phase, heavy duty, metal body, 300 mm (12") sweep, 900 RPM including fixing of mounting frame by means of rugged bolts, nuts and washers etc including louver shutter on outer surface of the wall and connecting with and including three core copper conductor flexible cord of 0.5 Sqmm cross sectional area of required length from ceiling rose to the porcelain connector block of the exhaust fan complete all as specified and directed.

Sub main wiring with two single core stranded copper conductor unsheathed PVC insulated 1.5 sqmm FRLS cable 1100V grade drawn through suitable size of non-metallic PVC rigid conduit/casing caping with one run 1.5 sqmm copper conductor FRLS cable as earth conductor and conduit accessories fixed up in surface/recessed as required, including connecting up complete all as specified and directed. Note:- Three runs of 1.5 sq mm cable and and one run of PVC conduit / casing caping shall be measured as one unit

DHANSHRI ENTERPRISES

Raghu M Contractor

RAJENDRA KRISHNA SARAF

ASHIRWAD ELECTRICALS

M/S MAHADEV M PATIL

DHAIRYASIL RAMAKANT DESAI