SPECIAL REPAIR TO BLDG NO. P-44 AT TRANSIT CAMP AND NP-100(A-B) (MD ACCN) AT CHIRWA ENCLAVE AND PROVN OF CHAIN LINK FENCE AT 213 TRANSIT CAMP AT NAGROTA UNDER GE NAGROTA

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm each and n. exc. 4.00 sqm each and removing from site, complete all as specified and directed.

Taking down chowkats with shutter n. exc 1.5 sqm each. (without taking of shutter from the frame) ,all as Specified

Pressed steel door frame of size 105 mm x 60 mm with two rebates including necessary fixing lugs, hings, lock strike plate , complete all as specified and directed.

Pressed steel door frame of size 125 mm x 60 mm with two rebates including necessary fixing lugs, hings, lock strike plate , complete all as specified and directed.

S&F 2nd class hardwood 40 mm thick plain, framed, panelled shutter (any numbers of panels) with panels of timber flat on both sides(feather edged) or of veneered particle board medium density wood particles board wih commercial face venners fitted to chowkhats complete all as specified and directed.

S & F 35 mm thick second class hard wood, factory made, glazed and skelton shutters, open rebated and prepared to receive glass, gauge, etc. (without sash bars), edges of framing plain, chamered or rounded, fitted with cut and mitred beads for securing glass, etc. Size of memebers of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) for doors, complete all as specified and directed.

S&F Box type Steel windows/ventiletors , including hinges, steel handle, tower bolt 100 mm and steel peg stay complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surface before fixing complete all specified and directed

S&F steel windows or ventilators fixed type with glazing bars complete all specified and directed.

S & F factory made solid PVC door frame of size 50mm x 47mm ,made out of 5mm plain colour PVC sheet reinforced with MS square tube as per specification and drawing, complete all as specified and directed.

S & F 30 mm thick (style) Factory made solid panel PVC door shutter consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed.

M&L Sheet glass 3mm thick, ordinary quality in squares n exc 0.5 sqm complete all as specified and directed.

M&L thick pin head glass 3mm thick, ordinary quality in squares n exc 0.5 sqm complete all as specified and directed.

S & F Galvanised mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40 mm dia and fixed with tinned tacks or galvanised mild steel staples, complete all as specified and directed.

S & F 150 mm aluminium anodised barrel tower bolt of extruded section and fixed, complete all as specified and directed.

S & F 75 mm aluminium anodised barrel tower bolt of extruded section and fixed, complete all as specified and directed.

S&F aluminium alloy anodised sliding door bolt with hasp staple (bolt type) 300 mm long, fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

S & F 100 mm long butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

S & F 75 mm long butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

S & F 150 mm long aluminium alloy handles, cast type, anodized, complete all as specified and directed.

S & F 100 mm long aluminium alloy handles, cast type, anodized, complete all as specified and directed.

S&F 300 mm mild steel oridinary rat tail rod pattern springs including roller and roller plates, complete all as specified and directed.

Prepration of wood or wooden based new or previously untreated surface of any description, over 10 cm width or gridth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

S&F in repair harrison rails , mild steel , chromium plated with fixing brackets, storps roller etc. complete all as specified and directed

Demolition of brick work / stone masonry built in cement mortar or cement lime mortar including all quoins ,arches , pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified and directed.

M&L brick work with sub class 'B' bricks in 1:6 cement mortar on straight or curved on plan exc 6 m , complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc, complete all as specified and directed.

M&L rendering 5 mm thick in CM 1:3 as in ceiling, soffit of chajja etc complete all as specified and directed

M & L for preparation of new plastered or unplastered surfaces of ceilings chajjas facia and applying three coats of white wash, complete all as specified and directed.

M & L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement, complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra cement, complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of cement base paint , complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over and including 3mm thick wall putty, complete all as specified and directed.

Preparation of old plastered surfaces of walls and applying one coat of cement base paint , complete all as specified and directed.

Preparation of old plastered surfaces of walls and applying one coat of oil bound distemper, complete all as specified and directed.

Dismantling floor , hearth or wall tiling including cement mortar bedding ( but not backing ), removing serviceable tiles to store and rubbish off the premises complete all as specified.

Demolition of cement concrete of any description and any position not otherwise specifically provided, complete all as specified and directed by Engr-in-Charge.

M&L for 75 mm thick cement concrete 1:3:6 type C-2 as in plinth protection complete all as specified and directed

M&L providing CM 1:2:4 type B-0 (12.5 graded aggregrate) as in roof kerbs or mud stops, rounded or chamferd on edges or as in treatment to sunken floor including water proofing compund @2% of cement complete all as specified and directed Note: WPC measured and paid separately

M&L for 25 mm thick plain cement concrete, 1:2:4, type B-0 ( using 40 mm graded crushed stone aggregate ) as in sub base to receive topping layer finished even and rough complete all as specified and as directed.

M&L for pre polished machine cut kota stone slab flooring 20 -25 mm thick over cement screed base laid and mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M&L for pre polished machine cut kota stone slab flooring 20 -25 mm thick in riser of steps skirting, dado, and pillar laid over cement screed base laid and mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M & L for Non-skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.06 sqm but n exc 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over complete all as specified and directed

M&L for 20mm thick screed bed or bedding layer of CM 1:4 for laying floor finish, complete all as specified and as directed.

M&L for 15 mm thick screed bed or bedding layer in cement mortar 1:6 on floors for laying floor finish, complete all as specified and as directed.

M&L for 10 mm thick rendering in CM 1:4 as in backing coat for skirtin/dados complete all as specified and directed

M & L for Glazed ceramic coloured printed tiles (first quality) of size 450 mm x 350 mm x 7 mm thick as in vertical surface, dado/skirting, set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified and directed.

M&L PCC 1:5:10 type E-2 (using 40 mm graded crushed stone aggregate) as in for sub base flooring and mass concrete complete as specified and directed.

M & L for chequered cement concrete tiles 20cm x 20cm x 25mm thick set, joined and pointed in neat cement slurry in floors with grey cement and no pigment , complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan(pedestal pattern) white excluding flushing cistern & flush pipe, complete all as specified and directed.

S&F in repairs 15 mm bore self cleaning water jet, chromium plated including all accessories , completed all as specified and directed

S & F in repairs 10 Ltrs capacity PVC valveles, symphonic action type, flushing cistern low level, white with inlet, ball valve, float and handle including bracket and mild steel tube 32 mm dia and 450mm long PVC connection, complete all as specified and directed.

S&F in repair Vitreous china wash basin, angle back, size 600 X 480 mm white excluding taps waster chain and plug and procelain stopper but including brakets complete all as specified and directed

S&F in repair vitrious china white soap dish 160x160x90 mm fixed to wall complete all as specified and directed

S&F 15 mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs including taking down complete all as specified and directed

Cutting chases pinning in making good to facing where required and pointing in CM 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good , cutting not exceeding 10 cm girth in brick wall complete all as specified and directed

S&F 20 mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs including taking down complete all as specified and directed

S & F in repair 15 mm bore brass, chromium plated, screwed down high pressure with and without levelled mixer for mixing hot or cold water with long screwed shanks and fly nuts screwed for pipe and fixed in repairs, complete all as specified and directed.

S & F 15 mm bore brass centre hole chromium plated, mixer for mixing hot and cold waer screwed down high pressure with and without levelled hot or cold water with long screwed shanks and fly nuts screwed for pipe and fixed in repairs, complete all as specified and directed.

S&F in repair 15mm bore Bib taps, CP fancy type with crutch or butterfly handle,screwed down,screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed by Engr-in-Charge.

S&F in repair 15 mm bore stop valve/angle fancy type , cromimum plated with long shank(concealed type) cast copper alloy screwed down high pressure a handle screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repair 20 mm gate valves with iron wheel head, screwed both ends for iron pipe complete all as specified and directed

S&F in repair 300 mm long glass corner shelf complete all as specified and directed

M & L for 75mm bore nahani trap with grating including jointing to waste pipe fixed in cement concrete 1:2:4 using crushed strone aggregte, complete all as specified and directed.

S&F for 125/110 mm PVC (SWR) gully trap setting and jointing with slovent cement complete all as specified and directed

S&F in repair 20 mm dia type D brass CP tubuler towel rail, 60 cm long between flanges complete all as specified and directed

S & F PVC connection 15 mm size with PTMT nuts with length 600 mm long, complete all as specified and directed.

Dismantling of water tanks and removing to store of capacity exc 250 ltr but not exc 500 ltr etc complete all as specified and directed

Supply and fix 500 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position , complete all as specified and directed.

S&F 20 mm bore ball valve PTMT valves.high pressure with polythene float and flynut complete scewed for iron pipe or brass ferrule and fixed in repair complete all as specified.

Dismantling of wrought iron or mild steel work in any description, complete all as specified and directed.

M&L for MS framed work such as water tank staging, and like including caps, bases, beam or channel sections, angles with plates etc, complete all as specified and directed

Mild steel Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165, complete all as specified and directed.

Prepration of newly steel surfaces any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Prepration of new or previously steel surfaces any description, not otherwise described n. exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specified and directed.

Prepration of old steel surfaces any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint , complete all as specified and directed.

M&L for PCC, 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate) as in roof kerbs or mud stops rounded or chamfered on edges or as in padding concrete, complete all as specified and directed.

M&L for 10mm thick rendering in CM 1:3 including water proofing compound @2% of cement over roof surfaces finished even and smooth without using extra cement, complete all as specified and directed. Note: WPC measured and paid separately

Supply only integral waer proofing compound

Applying bituminous primer @ 0.40 litre per sqm over plastered surfaces of roof including parapet surface complete all as speicified and directed

M&L for Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm , complete all as specified and directed.

One layer of APP (atatic polypropline) based polymeric membrane 3mm thick minimum weight not less than 3.5 kg/sqm reinforced with non wove polyester fabric or weight not less than 150 gms per Sqm, Polyester membrane shall be taken to a height 6 cm (minimum) and then inserted indise the groove of parapet wall and shell be finished by memhrane flashing. Note: (i) Laying of APP based polymeric membrane shall be done by torch on method or as per manufacturing instructions. (ii)A minimum overlap of 100mm and 75mm should be made in the end and sides of polymeric membrane respectively and sealed all overlaps and joints as manufacturers instructions. Note: S&F of APP based polymeric membrane of approved manufacturer will be laid/fixed by auhorized person of the same manufacturers units as per relevants IS.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out any type of soil, complete all as specified and directed.

M&L cement concrete 1:4:8 tpe D-2 using 40 mm graded stone in bed to drain pipe laid in trenches including packing and haunching against the sides of pipe after they are laid and tested for 150 mm dia drain pipe complete all as specified and directed

M&L for 150 mm dia salt glazed stone were drain pipes grade ‘A’ ISI marked laid to slope in trenches, jointed in CM (1:1) and tested, complete all as specified and directed.

Removing excavated surplus soil to a distance not exceeding 50m and depositing where directed and at a level not exceeding 1.5m above the starting point, complete all as specified and directed by Engr-in-Charge.

Returning, filling including spreading, levelling, watering and well ramming in layers not exceeding 25cm in soft/loose soil, complete all as specified and directed by Engr-in-Charge.

Cutting into existing manholes for connecting new drains and making good to pipes and rendering cutting out existing benching for and forming branching for and forming branch channel(1/2 round or 1/4 section) in PCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate smooth finished and reforming benching as specified and directed for 150 mm dia of pipe complete all as specified and directed

S&F in repair kitchen sink with drainage board made out of stainless steel sheet 1.0 mm thick with plug washers and CP waste coupling, overall size 915 mm x 460mm x 203mm with bowl of size 405 mm x 354 mm x203 mm incl fixing cantilever brackets and connecting unoin to waste pipe complete all as specified and directed

S&F 75 mm dia PVC(SWR) soil, waste and vent pipe, single sockets in any legth with rubber ring joints laid in trenches or in floors complete all as specified and directed

S&F 75 mm dia PVC(SWR) bends any radius, complete all as specified and directed

S & F 100 mm bore Cast iron waste and vent pipes sand cast in any length with or without ears with cement joints laid in floors or fixed to walls with all fittings, complete all as specified and directed.

All as per ser item No.92.00 here in above but 75 mm.

S & F in repairs 100 mm bore dia Cast iron bend (any radius) with duck foot sheet rest, including taking out old fitting complete all as specified and directed.

All as per ser item No.94.00 here in above but 75 mm.

S & F in repairs cast iron branch pieces single (equal or unequal ordinary or inverted or with parallel branches) for 100mm bore pipes fixed in repair including taking out old fitting, complete all as specified and directed.

All as per ser item No.97.00 here in above but 75 mm.

S&F steel ventilator with top hung shutter including hinges steel peg stay complete all as speicified and directed

Preparation of new/old decoreated plastered or unplastered surfaces of walll by brooming down or by steel wire brushes, scraping down smoke spot , moulds, mass and efflorescent salts, trading oil, greasy spots etc and applying one coat of white wash on walls after filling any hole with putty complete all as specified and directed

M&L for 40 mm thick plain cement concrete, 1:2:4, type B-1 ( using 40 mm graded crushed stone aggregate ) as in sub base to receive topping layer finished even and rough complete all as specified and as directed.

M & L for Non-skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm but n exc 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match , complete all as specified and directed.

M&L for 75 mm thick plain cement concrete, 1:2:4, type B-2 ( using 40 mm graded crushed stone aggregate ) as in base of florring/hard standing finished even and rough complete all as specified and as directed.

S&F in repairs vitreous china squatting pan ORRISA pattern, size 580x440mm white, with integral foot rest(excluding flushing cistern and flush pipe) including provn of concrete bedding and connection to trap and flushing pipe antisyphonage pipe etc including making good to floor, complete all as specified and directed.

S&F 15 mm piller taps cast coper alloy with capstan heads fancy type chromium plated screwd down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe , complete all as specified and directed.

S&F in repair grating doom 140 mm dia of PTMT(min weight 25 gms) complete all as specified and directed.

S&F in repair stainless steel plate rack madeout of 0.63 mm thick sheet wall mounted type with 5/6 portion of size 60cm x 90cm x 25 cm fixed on wooden gutties complete all as specified and directed by Engr-in-Charge.

M & L for Udaypur green stone 15 to 18 mm thick. (table rubbed and polished) as in cooking plateform of size not less than 2 m in length, incl cutting for sink over and including 20 mm thick screed in CM 1:4 including roughing of existing surface and applying a coat of cement slurry @ 03 Kg/Sqm of surface and pointing with white cement 1:2 using marble dusts admixture of pigment to match, complete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.5 cum, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft soil, watering and removing surplus soil to a distance n.exc 50 m complete all as specified and directed.

M & L for PCC 1:4:8 type B-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete, complete all as specified and directed.

Mild steel work as in posts and struts in fencing including cutting tops to shape as directed , drilling holes, notching for wire , etc., including all necessary drilling, bolting or riveting etc., and similar work confirming to Fe-290 Gde E-165 complete, all as specified .

Supply only for 4 mm dia galvanised sel wire of mesh size 75 mm x 75 mm made up into matteress or cages, lapped wire and laid in position including closing after filling including fixing to steel post by welding etc complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh , size and type of any type of sandards , rails, straining bolt, etc including provision of binding wire complete all as specified and directed.

Preparing of previously painted/new steel surface of any description, and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer in charge.

M&L Framed work as in door or gate of angles or other section's with gusset plate, rails, braces etc, complete, drilled for fixing of steel sheeting or other covering, doors etc to be prepared for handing or sliding with and including either hooks and hinges or steel hagning door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete all as specified and directed

Taking down carefully aluminium conductor point wiring (light fan, socket and power) complete with fittings such as switches, sockets, lamps holder, utility light fitting, fan regulator etc and making good disturbed surface of walls and floors etc. and keeping in safe custody for taking credit, complete all as specified and directed by Engr-in-Charge.

Taking down ceiling fan any sweep, removing blades, cleaning the fan completly for dust and dirt and hanging the same back to its original position including connecting the 3 core flexible copper wire to ceiing rose etc after the completion the point wiring including replacement old unservicable fan hook, rubber pad, nut bolts and washers etc, complete all as specified and directed by Engineer in charge.

M&L for point wiring with PVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium grade ISI marked not less than 20mm dia ,concealed in wall and surface on ceiling with all conduit fittings & fixing acessories inculding sunken anodised pressed steel terminal box not less than 1.2mm thick covered with 3 mm thick plastic laminated sheet cover of suitable size with brass screws for mounting switches, sockets, regulators with and including 1.5sqmm FRLS multi stranded copper conductor drawing as continuous earth wire connected to main earth and earth dolly, complete all as specified and directed for the following:-

(a) One light point controlled by one switch 5 Amp.

(b) One ceiling fan/exhaust fan point controlled by one switch 5Amp

(c) One socket outlet 5Amp controlled by one switch on same board.

(d) One socket outlet 5 Amp controlled by one switch on independent board.

(e) One socket outlet 5 Amp controlled by one bell push on independent board.

(f) One light point controlled by two, 2 way switche 5 Amp

All as per item No.117.00 here in before but point wiring with 2.5sqmm FRLS multi stranded copper conductor cable for main circuit and 2.5sqmm cable as earth continuity conductor for one 15 Amp socket out let controlled by one 15 Amp switch on independat board.

S&F switch piano flush type 5 Amps single pole one way, complete all as specified and directed.

S&F socket outlet combination 2 in 1, 3 pin, 5 Amp flush type, complete all as specified and directed.

S&F switch socket combination 2 in 1, 3 pin, 5 Amp flush type, complete all as specified and directed.

S&F switch socket combination 2 in 1 5 pin 5 /15 Amps flush type, complete all as specified and directed.

S&F of ceiling rose 3 terminal PVC/Polycarbonate isolated body, complete all as specified and directed.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc as required, complete all as specified and directed.

S&F bell push piano type 5 Amps complete all as specified and directed

S&F switch piano type 5 Amps 2 way complete all as specified and directed

S&F electric bell ding dong 230 volts AC complete all as specified and directed

S & F Integrel sleek extruded batten aluminium /CRCA channel fitting with LED 18 watt complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, or equivalent in approved make, complete all as specified and directed.

S & F batten integrated LED channel of 5W, 230 V frequency 50/60 Hz integral sleek extruded polycarbonate LED channel with white acrylic cover, power factor not less than 0.9 , complete all as specified and directed.

S & F LED light fitting 1x9W bulk head luminaries IP 65 complete with all accessories including LED lamp 9 watt , connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V 50 Hz, complete all as specified and directed.

S&F lamp holder PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S & F LED bulb 7 watt complete all as specified and directed.

S&F in rpeiar sheet metal enclosure distribution board SPN 12 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail, complete all as specified and directed.

S & F in repair Sheet metal enclosure double door for distribution board factory made for MCB DB load link TPN 4 way suitable for MCCB as incomer, 63 Amp,4 pole. (when MCB's are to be used) with suitable size of busbar complete,fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification, complete all as specified and directed.

S & F MCB DP 63 Amps 10 KA 230 volts "C" series, complete all as specified and directed.

S & F MCB single pole 6 to 30 Amps, 10KA, 230 volts 'C' series, complete all as specified and directed.

S & F MCB single pole 40 Amps, 10KA, 230 volts 'C' series, complete all as specified and directed.

S&F in repairs of MCCB 63 Amps, 4 pole, 415 Volts, 16 KA, with adjustable thermal and adjustable magnetic settings as per existing at site, complete all as specified and directed by Engr-in-Charge.

Sub main wiring with two single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6 Sq mm drawing through and including concealed rigid non metallic PVC conduit medium grade ISI marked 20 mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6.0 sq mm as earth continuity conductor connected to commen earth and earth dolly including taking down existing old unserviceable cable, complete all as specified and directed

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit shall be filled with charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) as specified including provision of 15mm dia medium grade GI pipe for earth wire protection and 20 mm dia for watering complete , all excavation and earth work & connecting the earthing to an earthing test point / main switch board as specified and testing on completion, complete all as specified and directed.

S & F in repair Sheet metal enclosure double door for distribution board factory made for MCB DB load link TPN 4 way suitable for MCCB as incomer, 125 Amp,4 pole. (when MCB's are to be used) with suitable size of busbar complete,fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification, complete all as specified and directed.

S&F in repairs of MCCB 125 Amps, 4 pole, 415 Volts, 16 KA, with fixed thermal and adjustable magnetic settings as per existing at site, complete all as specified and directed by Engr-in-Charge.

M&L for sheet steel box fabricated out of 2 mm thick steel sheet of size 60x60x25 cm duly painted by synthetic enamel paint over a coat of primer,compartmentalized suitable to accommodate 4 Nos energy meter independently each compartment shall be provided with suitable door and 2 Nos fancy lock including taking out existing wooden meter box complete all as specified and directed by Engr-in-Charge

Taking down existing energy meters, keeping aside safely & refixing the same in its original position after making functional & after completion of point wiring/sub main wiring, complete, all as specified and directed by Engr-In-Charge. Note:- Small items required for fixing the electric energy meter at site shall be provided by the contractor and cost for the same shall be deemed to be included in the quoted rates.

Taking down existing electric water heater, keeping aside safely & refixing the same in its original position after servicing of the whole geyser/making functional and afer completion f wiring work, complete all as specified and directed by Engr-In-Charge. Note:- If any part found unserviceable during the refixing of water heater at site shall be provided by the contractor and cost for the same shall be deemed to be included in the quoted rates.

S&F PVC connecting 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

Deduction to be made from BOQ for schedule of credit (Sch 'A' Part - II) Amount of ₹ 48,881.00 during AOC Note:- Tenderers shall not quote for this Schedule

MAMTA ENTERPRISES

BHARTI CONSTRUCTIONS