AUGMENTATION OF EXTERNAL WATER SUPPLY

Amount

Lump sum price worked out by the tenderer for "Building / Structure Work" as listed in Schedule ‘A’ Section - I.

Lump sum price worked out by the tenderer for “BITUMINOUS ROAD WORKS" as listed in Schedule ‘A’ Section - II (Part-I)

Sch 'A' Sec - II (Part-II), (BITUMINOUS ROAD WORK)

Material and labour for continous Jodhpur stone slab edging 7.5cm to 10cm thick, 30cm wide (for depth of edging) and 35 to 45cm long, lad dry vertically jointing and pointing in CM (1:4), each stone slab self faced on both the vertical sides, edges slightly true and square on top edge hammer dressed for the full thickness so that the depression from the straight edge held against the surface shall not exceed 20mm between two slabs including excavation and embedding to depth required and temping ground around stone edging, returning filling and disposal of surplus soil to a distance not exceeding 50m, complete all as specified and as directed.

Subtotal

Lump sum price worked out by the tenderer for “SECURITY WALL, CHAIN LINK FENCING, AND STEEL GATE WORKS" as listed in Schedule ‘A’ Section - III

Lump sum price worked out by the tenderer for “EXTERNAL WATER SUPPLY WORKS" as listed in Schedule ‘A’ Section - IV (Part-I)

Sch 'A' Sec - IV (Part-II) (EXTERNAL WATER SUPPLY WORKS)

Supply and fixing cast iron double flanged duck foot bend suitable for 200mm bore pipe including jointing materials such as nuts, bolts, washers, rubber gaskets etc with and including embedding in thrust PCC blocks (as shown on drawing) complete all as specified and as directed.

Supply and fixing cast iron double flanged duck foot bend suitable for 150mm bore pipe including jointing materials such as nuts, bolts, washers, rubber gaskets etc with and including embedding in thrust PCC blocks (as shown on drawing) complete all as specified and as directed.

Material and labour for 150mm bore medium grade GI pipe making perforated with 12mm dia holes drilled, both ends flanged fitted one end to the inlet vertical pipe of 150mm dia and other end embedded in concrete in OHR complete all as specified and as directed and shown on drawings.

Supply and fixing Cast iron pipe 150mm bore, centrifugally cast, class 'B' , (ISI marked) with both ends flanged pipes (from sluice valve to extended Inlet and outlet pipes upto 3mtr beyond plinth protection of OHR or as directed) complete all as specified and as directed and shown on drawing.

Supply and fixing Cast iron pipe 200mm bore, centrifugally cast, class 'B' , (ISI marked) with both ends flanged pipes (from sluice valve to extended outlet pipes upto 3mtr beyond plinth protection of OHR or as directed) complete all as specified and as directed and shown on drawing.

Supply and fixing Cast iron pipe 150mm bore, centrifugally cast, class 'LA' , (ISI marked) with both ends flanged pipes (from sluice valve to extended washout pipes upto 3mtr beyond plinth protection of OHR or as directed) complete all as specified and as directed and shown on drawing.

Supply and fixing Cast iron pipe 200mm bore, centrifugally cast, class 'LA' , (ISI marked) with both ends flanged pipes (from duck foot bend/sluice valve to extended overflow/wash out pipes upto 3mtr beyond plinth protection of OHR or as directed) complete all as specified and as directed and shown on drawing.

Supply, fixing, commissioning and testing digital water level indicator with five stage magnetic level sensing probe unit made of stainless steel (SS-304) of minimum 16mm dia probe stem customised to depth of the tank and sensors epoxy sealed in the probe stem actuated by float the move on the probe stem with the level of water in tank and reading shown in LED digital panel (display panel size 100mm, 4 digit), level indicator should be complete with alarm on low and hogh level (both visual and audio ) by pass facility for audio alarm including all fittings and fixing arrangement, connection from probe unit to panel and DB to panel as per manufacturerer's instructions complete all as specified and as directed . Make : Active controls / RAWACO /Century 21st / Unison / Alphatech / Sinetrac. Notes:- Flexible Cable for connection and protection pipe shall be measured and paid separately under appropriate item of BOQ)

Supply, fixing and drawn through pipe 1100 volt grade flexible PVC insulated, multi strand copper conductor cable of size 1.5 Sqmm circular twin core for service connections to water level indicator from probe unit (installed at OHR ) to display panel (installed at pump house) and for supply to panel from DB including making all connections as per water level indicator manufacturerer's instructions complete all as specified and as directed. Note ;- Pipe shall be measured and paid separately under respective item of BOQ.

Supply and fixing 20mm dia PVC rigid conduit (heavy duty, ISI marked) for cable protection, fixed along RCC pillar/wall surfaces from top of OHR to display panel (installed at pump house), laid in trenches/under floor including all fittings and fitting arrangements such as bends, elbows, tees, end cap, PVC clamps, rawl plug, screw, couplers, lock unit, saddles, pipe hooks, terminal box etc. complete all as specified and as directed. Note ;- Excavation and earth work as required shall be measured and paid separately under respective item of Sch/BOQ.

Supply and fixing cast iron foot valve ISI marked, flanged type, suitable for 150mm bore pipe including jointing materials such as nuts, bolts, washers, rubber gaskets etc complete all as specified and as directed.

Supply and fixing cast iron double air relase valve isolating type (ISI marked), flanged type and drilled, confirming to IS-14845, suitable for 80mm bore pipe including jointing materials such as nuts, bolts, washers, rubber gaskets etc complete all as specified and as directed.

Supplying, laying, jointing and testing Ductile iron pipe class K-9 confirming to IS : 8329 of bore 200 mm (ISI marked), spigot & socketed ends centrifugally cast suitable for rubber tyton joints complete all as specified and as directed. Note : (a) Earth work and DI specials/ fittings shall be measured and paid separetly. (b) Cost of joints including jointing materials shall deemed included in unit rate quoted by contractor.

Supplying, laying, jointing and testing Ductile iron pipe class K-9 confirming to IS : 8329 of bore 150 mm (ISI marked), spigot & socketed ends centrifugally cast suitable for rubber tyton joints complete all as specified and as directed. Note : (a) Earth work and DI specials/ fittings shall be measured and paid separetly. (b) Cost of joints including jointing materials shall deemed included in unit rate quoted by contractor.

Supplying & fixing Ductile iron specials/ fittings of any size, any type like Bends, tapers, increasing, decreasing sockets, tees (Single and double branch), tail pieces and collars etc complete all as specified and as directed. Note:- Make of DI fittings shall be same make as that of DI pipe or of make recommended by manufacturer of pipe.

Material and labour for Cutting of existing CI/DI pipes upto 200mm bore in trenches for fixing /insertion of new tee/pipe line/fittings etc complete all as specified and as directed. NOTE:- Excavation, Earth works and new tee/pipe/fittings etc as required shall be measured and paid for separately.

Excavation by trenchless technology for boring of holes under road, pavement, hard-standing using trenchless boring machine or by means of manual manpower suitable for inserting upto 200 mm dia pipe including removal of surplus soil and making good distrub surface complete all as specified and as directed. NOTE:- Pipe for inserting as required shall be measured and paid for separately.

Material and labour for Construction of brick masonary valve pit chamber size 120 X 120 X 120 cm (internal dimension) using sub class 'B' bricks complete including excavation & earth work, returning fillig and disposal of surplus soil to distance not exceeding 50m and deposited where directed, PCC (1:4:8) type D-2 using 40 mm graded stone aggregate in foundation, coping on top in PCC (1:2:4) type B-1 using 20 mm graded stone aggregate, brick work in cement mortar (1:4), inner plaster 12 mm thick in cm (1:4) finished even and smooth and pionting flush externally as the work proceeds in the same mortar, MS sheet cover 3.15mm thick mounted on angle iron frame of size 40 x 40 x 6mm with handle and locking arrangement duly painted with two coats of synthetic enamel paint over a coat of red oxide primer and embeded portion of MS work duly applying black bitumenous paint before embeded complete all as specified and as directed and shown on drawings.

Supply, installation , commissioning and testing of centrifugal pump set electric motor driven, discharge capacity not less than 1400 LPM at 50 mtr head, suitable for pumping clear water, complete pump set with motor with all accessories and comprising of the following specifications :-

Pump centrifugal type, horizontal, split casing,1440 RPM, discharge not less than 1400 LPM at 50 mtr head having bronze impeller and stainless steel shaft, single stage directly coupled with electric motor through flexible tyre coupling with coupling guard.

Squirrel cage induction motor, TEFC, 3 Phase 415 ± 10 Volts, 50C/S, AC supply not less than 40 HP, 1500 RPM directly coupled to centrifugal pump set including all electrical connection with 02 runs of PVC insulated sheathed three core 16sqmm multi strand copper cable drawn through and including flexible PVC conduit from motor to starter panel with copper lugs, cable gland etc.

Common base foundation of ICMC-100 suitable for installation of above pump set duly drilled holes and painted with two coats synthetic enamelled paint over a coat of red oxide primer.

PCC foundation :- PCC (1:3:6) type C2 using 40mm graded stone aggregate, 30cm on above GL and 15 cm below GL, including grouting of eye bolts, nuts washer etc as per size of common base foundation/standard engineering practice/ manufacture recommendation including excavation and earth work.

Bourdons type pressure gauge 3” dia dial type SS body with check valve.

Suitable size of GI medium grade pipe with fittings for suction matching with pumps and addition/alteration of suction and delivery side of pump including DI pipe upto 2.0 mtr with fittings including nut, bolts, washer, rubber gasket and flange etc.

Note : - Pre-commissioning inspection/test of pump set shall be carried out by the rep of accepting officer.

Supply, installation , commissioning and testing of centrifugal pump set electric motor driven, discharge capacity not less than 1100 LPM at 60 mtr head, suitable for pumping clear water, complete pump set with motor with all accessories and comprising of the following specifications :-

Pump centrifugal type, horizontal, split casing,1440 RPM, discharge not less than 1100 LPM at 60 mtr head having bronze impeller and stainless steel shaft, single stage directly coupled with electric motor through flexible tyre coupling with coupling guard.

Squirrel cage induction motor, TEFC, 3 Phase 415 ± 10 Volts, 50C/S, AC supply not less than 40 HP, 1500 RPM directly coupled to centrifugal pump set including all electrical connection with 02 runs of PVC insulated sheathed three core 16sqmm multi strand copper cable drawn through and including flexible PVC conduit from motor to starter panel with copper lugs, cable gland etc.

Common base foundation of ICMC-100 suitable for installation of above pump set duly drilled holes and painted with two coats synthetic enamelled paint over a coat of red oxide primer.

PCC foundation :- PCC (1:3:6) type C2 using 40mm graded stone aggregate, 30cm on above GL and 15 cm below GL, including grouting of eye bolts, nuts washer etc as per size of common base foundation/standard engineering practice/ manufacture recommendation including excavation and earth work.

Bourdons type pressure gauge 3” dia dial type SS body with check valve.

Suitable size of GI medium grade pipe with fittings for suction matching with pumps and addition/alteration of suction and delivery side of pump including DI pipe upto 2.0 mtr with fittings including nut, bolts, washer, rubber gasket and flange etc.

Note : - Pre-commissioning inspection/test of pump set shall be carried out by the rep of accepting officer.

Supply, installation, commissioning and testing of silent Diesel Engine driven Generating set, capacity 62.5 KVA outdoor type, 415 Volts, 3 phase 4 wire, 1500 RPM, liquid cooled engine as per IS 10001/10002 and brushless Alternator as per IS: 13364 complete with foundation (as per OEM design), electronic type governor, PF 0.8, control panel with Microprocessor controller with necessary meters and sound proof canopy of authorised OEM of manufacturer's of DG set given in appendix 'B' as per CPCB norms, including maintenance free battery (as recommended by manufacturer of DG set) as per IS 14257, inbuilt battery charger, including connections with suitable size as directed 3.5 core XLPE armoured electric cable from DG set to existing change over switch of electric panel of pump set complete all as specified and as directed and comprising with the following :-

Diesel engine: Diesel engine 4 stroke water cooled electric start of suitable BHP at 1500 RPM suitable for above output of alternator at 47°C, 50% RH and conforming to BS 5514, BS 649, IS 10000 capable of taking 10 % over loading for one hour after 12 hour of continuous operation. The engine will be fitted complete with all the required accessories.

Engine mounted instrument panel fitted with and having digital display for following:- (i) Start top switch with key. (ii) Water temperature indication. (iii) Lubrication oil temperature indication. (iv) Battery charging indication. (v) RPM indication (vi) Over speed indication. (vii) Low lubrication oil trip indication (viii) Engine hour indication.

Alternator- synchronous alternator rated at 62.5 KVA, 415 Volts at 1500 RPM 3 Phase 50 Hz, AC supply with 0.8 lagging power factor at 47°C, 50 % RH. The alternator shall be having SPDP enclosure, brushless, continuous duty, self excitation and self regulated through AVR confirming to IS - 4722/BS 2613 suitable for tropical conditions and with class F/H insulations.

Base frame and foundation. Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendation of manufacturer.

Fuel Tank : In built fuel tank for 12 hours fuel capacity, fabricated out of 3 mm thick MS sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with MS class C pipe of suitable dia complete with valves. Level indication and accessories as required as per specification

Exhaust system Dry exhaust manifold with hospital exhaust silencer and catalytic converter

Starting system. 12 V/24 V starting system comprising of starter motors, Voltage regular and arrangement for initial excitation complete with suitable Nos of maintenance free batteries as per manufacturer design.

Acoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine and alternator, excitation, discharging hot air in to the atmosphere as per specification

Note :- (a) Initial filling of lubricating oil/ coolant and fuel required for testing will provided by the contractor. (b) All arrangement for pre-commissioning test shall be made by contractor and cost for the same shall deemed to be included in the quoted unit rate, nothing shall be paid extra on this account. (c) Pre commissioning test shall be carried out by rep of accepting officer. Test shall be carried out for duration of 12hrs.

Supply installation, testing and commissioning of silent Diesel Engine driven Generating set, capacity 82.5 KVA outdoor type, 415 Volts, 3 phase 4 wire, 1500 RPM, liquid cooled engine as per IS 10001/10002 and brushless Alternator as per IS: 13364 complete with foundation (as per OEM design), electronic type governor, PF 0.8, control panel with Microprocessor controller with necessary meters and sound proof canopy of authorised OEM of manufacturer's of DG set given in appendix 'B' as per CPCB norms and with maintenance free battery (as recommended by manufacturer of DG set) as per IS 14257, inbuilt battery charger, including connections with suitable size as directed 3.5 core XLPE armoured electric cable from DG set to existing change over switch of electric panel of pump set complete all as specified and as directed and comprising with the following :-

Diesel engine: Diesel engine 4 stroke water cooled electric start of suitable BHP at 1500 RPM suitable for above output of alternator at 47°C, 50% RH and conforming to BS 5514, BS 649, IS 10000 capable of taking 10 % over loading for one hour after 12 hour of continuous operation. The engine will be fitted complete with all the required accessories.

Engine mounted instrument panel fitted with and having digital display for following:- (i) Start top switch with key. (ii) Water temperature indication. (iii) Lubrication oil temperature indication. (iv) Battery charging indication. (v) RPM indication (vi) Over speed indication. (vii) Low lubrication oil trip indication (viii) Engine hour indication.

Alternator- synchronous alternator rated at 82.5 KVA, 415 Volts at 1500 RPM 3 Phase 50 Hz, AC supply with 0.8 lagging power factor at 47°C, 50 % RH. The alternator shall be having SPDP enclosure, brushless, continuous duty, self excitation and self regulated through AVR confirming to IS - 4722/BS 2613 suitable for tropical conditions and with class F/H insulations.

Base frame and foundation. Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendation of manufacturer.

Fuel Tank. In built fuel tank for 12 hours fuel capacity, fabricated out of 3 mm thick MS sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with MS class C pipe of suitable dia complete with valves. Level indication and accessories as required as per specification

Exhaust system Dry exhaust manifold with hospital exhaust silencer and catalytic converter.

Starting system. 12 V/24 V starting system comprising of starter motors, Voltage regular and arrangement for initial excitation complete with suitable Nos of maintenance free batteries as per manufacturer design.

Acoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine and alternator, excitation, discharging hot air in to the atmosphere as per specification.

Note :- (a) Initial filling of lubricating oil/ coolant and fuel required for testing will provided by the contractor. (b) All arrangement for pre-commissioning test shall be made by contractor and cost for the same shall deemed to be included in the quoted unit rate, nothing shall be paid extra on this account. (c) Pre commissioning test shall be carried out by rep of accepting officer. Test shall be carried out for duration of 12hrs.

Supply and fixing four pole offload changeover switch 200 Amps, 415 Volts with sheet metal enclosure front handle complete all as specified and as directed.

Supply, installing, commissioning and testing of factory made indoor type LT cubical panel board suitable for operation on 415 Volt, 3 Phase, 4 wire, 50 Hz supply system including bus bar chamber in centre (vertically) and cable allay either side, shell shall be made out of 2.0 mm thick CRCA sheet duly powder coated siemens gray shade and completely weather, vermin and dust proof, adequate air ventilation at sides and back with hinges and locking arrangements half nob type without key type with MS angle iron frame and legs made from angle of size 50 x 50x6mm duly painted with two coats of synthetic enamelled paint over a coat of red oxide primer. Foundation is not less than 30cm below ground level and not less than 45 cm above ground level, legs of panel will be grouted in PCC (1:2:4) type B-I 20mm graded stone aggregated and MC 100 pedestal for grouting in floor with suitable nut bolts, washers etc including foundation fittings and compartmentalized for taking out incoming and outgoing cables duly marked with riveted letter plates of appropriate size for each feeder/block cable danger board detachable plate at bottom for cable entry etc complete all as directed and comprising with the following :-

300 Amps Aluminium Bus Bar for phase or natural - 01 Set

MCCB 4 Pole 200 Amps, 36 KA with adjustable thermal magnetic release - 01 No

MCCB 3 pole 63 Amps, 16 KA or as recommended by manufacturer of pump set which ever is higher – 02 Nos.

MCB SPN, 32 Amp C series – 01 No

Fully automatic star delta starter for motor - 02 Nos with following. (i) Power contactor, star & delta contactor suitable for each 40 HP motor -01 set. (ii) Over load relay suitable for each 40 HP motor -01 No (iii) Star-Delta timer for each motor -01 No (iv) Low and high voltage protection relay -01 No

CT/PT, Internal all links connectors, insulators & control copper cable and LED indicators for On/Off, push buttons of start/stop for motor – 01 set

Single phase preventer with under voltage and over voltage protection – 02 Nos

LED indicators (R,Y,B) -01 set.

Note :- Drawing of panel shall be approved by GE before fabrication.

Supply, installing, commissioning and testing of factory made indoor type LT cubical panel board suitable for operation on 415 Volt, 3 Phase, 4 wire, 50 Hz supply system including bus bar chamber in centre (vertically) and cable allay either side, shell shall be made out of 2.0 mm thick CRCA sheet duly powder coated siemens gray shade and completely weather, vermin and dust proof, adequate air ventilation at sides and back with hinges and locking arrangements half nob type without key type with MS angle iron frame and legs made from angle of size 50 x 50x6mm duly painted with two coats synthetic enamelled paint over a coat of red oxide primer. Foundation is not less than 30cm below ground level and not less than 45 cm above ground level, legs of panel will be grouted in PCC (1:2:4) type B-I 20mm graded stone aggregated and MC 100 pedestal for grouting in floor with suitable nut bolts, washers etc including foundation fittings and compartmentalized for taking out incoming and outgoing cables duly marked with riveted letter plates of appropriate size for each feeder/block cable danger board detachable plate at bottom for cable entry etc complete all as directed and comprising with the following :-

300 Amps Aluminium Bus Bar for phase or natural - 01 Set

MCCB 4 Pole 200 Amps, 36 KA with adjustable thermal magnetic release - 01 No

MCCB 3 pole 63 Amps, 16 KA or as recommended by manufacturer of pump set which ever is higher – 04 Nos.

MCB SPN, 32 Amp C series – 01 No

Fully automatic star delta starter for motor - 04 Nos with following. (i) Power contactor, star & delta contactor suitable for each 40 HP motor -01 set. (ii) Over load relay suitable for each 40 HP motor -01 No (iii) Star-Delta timer for each motor -01 No (iv) Low and high voltage protection relay-01 No

CT/PT, Internal all links connectors, insulators & control copper cable and LED indicators for On/Off, push buttons of start/stop for motor – 01 set.

Single phase preventer with under voltage and over voltage protection – 04 Nos

LED indicators (R,Y,B) -01 set.

Note :- Drawing of panel shall be approved by GE before fabrication.

Subtotal

Lump sum price worked out by the tenderer for “EXTERNAL ELECTRIFICATION AND LIGHTENING PROTECTION WORKS" as listed in Schedule ‘A’ Section - V (Part-I)

Sch 'A' Sec - V (Part-II), (EXTERNAL ELECTRIFICATION AND LIGHTENING PROTECTION WORKS)

Supply and fixing Aviation obstruction light fitting, twin type, comprising of aluminium alloy housing with polycarbonate enclosure and accessories complete with LEDs to be fixed on the OHR with suitable fixing accessories as shown on drawing complete all as specified and as directed. Make :- Bajaj Cat part No BGAV302 LED or equivalent in Philips/Wipro/Crompton

Material and labour for Sub main wiring (using colour coding such as red, black, white and green colour or as directed) for connection to aviation light at top of OHR /any other light fittings elsewhere with 1.5 Sq.mm single core FRLSH PVC insulated unsheathed multistranded copper conductor 1100 V grade (03 run i.e 2 runs for main phase and nutral, 01 run for earthing) drawn through and including 20mm bore PVC rigid conduit (heavy duty, ISI marked) fixed along RCC pillar/wall surfaces from top of OHR to DB including all fittings and fitting arrangements such as bends, elbows, tees, end cap, PVC clamps, rawl plug, screw, couplers, lock unit, saddles, pipe hooks, terminal box etc. complete all as specified and as directed. Note :-Three runs of copper conductor and one run of PVC conduit including accessories shall be measured and paid as one unit.

Supply and fixing Factory made DB (made out of CRCA sheet) SPN, 04 Way with 200 Amps rated busbars 230/240V, double door, dust and vermin proof, protection class IP-54 with and including 01 No MCB, SPN, 10KA, 10 Amp and 01 No MCB, SP, 6 Amp, 'C' curve including fixing arrangement complete all as specified and as directed.

Sand cushioning, with dry and clean local tibba sand (for under ground cable) 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cable complete all as specified and as directed. (Note:- (i) Punned thickness shall be considered for payment purpose (ii) Approved local Tibba dry sand free from vegetations, grass and other deleterious substances shall be used.)

Supply and laying Best quality, locally available, sub class ‘B’ bricks (Old Size) for cable protection cover, laid flat and dry in trenches over the cable , perpendicular to the direction of cable complete all as specified and as directed.

Material and labour for Cable path indicator, duly engraved with 'LT CABLE 1100 VOLT' on cast iron round plate 150 mm dia and 8 mm thick with provision of 600 mm long (minimum) single leg/stand of angle iron 25 x 25 x 3 mm, welded/riveted on back side of plate, fixed and grounted in position with PCC type C-1, block of size 300mm x 300 mm x 200 mm complete all as specified and as directed.

Supply and fixing LT panel pillar box cubical type of size 120x100x50 cm (Panel box size), with bus bar chamber having 4 wire 415 Volts, factory made dust proof vermin proof for out door use made out of CRCA sheet 3.15 mm thick powder coated, machine pressed, both side opening with double door (front & rear) in two shalves with provision of rubber beadings and locking system, danger Notice board infront and rear sides including insulated aluminium bus bar of 400 Amp capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers, each MCCB/ cubical switch shall have be independent opening, panel shall be mounted on angle iron frame and legs made from angle of size 50x50x6mm , frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, legs grouted in PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) complete including all connections/control wiring incoming/out going with suitable size of copper conductor cable, Foundation is not less than 30 cm below ground level and not less than 45 cm above ground level, legs of panels will be grouted in centre of PCC foundation ( Size of foundation 100 cm x 30 cm x 75 cm-02 Nos) centre place will be open for connection of Under ground cables complete all as specified and as directed and comprising with the following :-

MCCB 250 Amp Adjustable thermal setting 36 KA, FP, single frame, thermal magnetic trip (incoming) - 01 No

MCCB 200 Amp 36 KA, FP, single frame thermal magnetic trip (outgoing) - 01 No

MCCB 63 AMP, 25 KA , FP, single frame, thermal megnetic trip (outgoing) - 02 Nos.

Indicating lamps LED type (RYB) -01 set of three.

MCB SPN 32 Amp ( for street light)

Note :- Drawing of panel shall be approved by GE before fabrication.

Supply and fixing LT panel pillar box cubical type of size 120x100x50 cm (Panel box size), with bus bar chamber having 4 wire 415 Volts, factory made dust proof vermin proof for out door use made out of CRCA sheet 3.15 mm thick powder coated, machine pressed, both side opening with double door (front & rear) in two shalves with provision of rubber beadings and locking system, danger Notice board infront and rear sides including insulated aluminium bus bar of 400 Amp capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers, each MCCB/ cubical switch shall have be independent opening , panel shall be mounted on angle iron frame and legs made from angle of size 50x50x6mm , frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, legs grouted in PCC (1:2:4) type B-1(using 20 mm graded stone aggregate) complete including all connections/control wiring incoming/out going with suitable size of copper conductor cable, Foundation is not less than 30 cm below ground level and not less than 45 cm above ground level, legs of panels will be grouted in centre of PCC foundation (Size of foundation 100 cm x 30 cm x 75 cm- 02 Nos) centre place will be open for connection of Under ground cables complete all as specified and as directed and comprising with the following :-

MCCB 250 Amp Adjustable thermal setting 36 KA, FP, single frame, thermal magnetic trip (incoming) - 01 No

MCCB 160 Amp 36 KA, FP, single frame adjustable thermal magnetic trip (outgoing) - 01 No

MCCB 63 AMP, 25 KA , FP, single frame, thermal megnetic trip (outgoing) - 02 Nos.

Indicating lamps LED type (RYB) -01 set of three.

Note :- Drawing of panel shall be approved by GE before fabrication.

Material and labour for Earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI earthing strip of size 25 x 4 mm flat by means of GI bolts/nuts/washers, protected by 40 mm bore GI light grade pipe upto test point or upto electric equipment, fixing with 02 Nos nuts and bolts. Earth plate shall be surrounded by alternate packed layer 15 cm thick of charcoal or coke and common salt all around bottom and top. 20 mm bore GI medium grade pipe for watering and including funnel, wire mesh, PCC chamber pit made with PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) including necessary form work, excavation and earth work in any type of soil, returning filling and disposal of surplus soil to a distance not exceeding 50m, Pit cover 40mm thick made with RCC (1:2:4) type B1 (using 20 mm graded stone aggregate) including TMT reinforcement 8mm dia @ 75mm c/c both way, MS handle 12mm dia, cover rest on MS angle iron frame 40x40x6mm embeded in concrete, MS angle frame duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified & shown in electrical plate No. 3 of SSR 2009 (Part-I) and all as directed. Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) Protection pipe and earthing strip upto test point or upto electric equipment from top of earth plate shall be included in the unit rate of this item. (iii) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge. (iv) Test point as per site requirement, same shall be measured & paid separately. (v) Qty 04 Nos for OHR Lightening protection works, 16 Nos for External electric supply works and 30 Nos for External water supply works )

Material and labour for Earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI earthing wire of size 4 mm dia by means of GI bolts/nuts/washers, protected by 15 mm bore GI light grade pipe upto test point or upto electric equipment, fixing with 02 Nos nuts and bolts. Earth plate shall be surrounded by alternate packed layer 15 cm thick of charcoal or coke and common salt all around bottom and top. 20 mm bore GI medium grade pipe for watering and including funnel, wire mesh, PCC chamber pit made with PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) including necessary form work, excavation and earth work in any type of soil, returning filling and disposal of surplus soil to a distance not exceeding 50m, Pit cover 40mm thick made with RCC (1:2:4) type B1 (using 20 mm graded stone aggregate) including TMT reinforcement 8mm dia @ 75mm c/c both way, MS handle 12mm dia, cover rest on MS angle iron frame 40x40x6mm embeded in concrete duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified & shown in electrical plate No. 3 of SSR 2009 (Part-I) and all as directed. Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) Protection pipe and GI earthing wire upto test point or upto electric equipment from top of earth plate shall be included in the unit rate of this item. (iii) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge. (iv) Test point as per site requirement, same shall be measured & paid separately. (v) Qty 02 Nos for Aviation light and and 16 Nos for External electric supply works )

Supply and fixing energy efficient LED street light fitting of 45W pressure die cast aluminium housing/body, heat resistant clear toughened glass, better optics for uniform distribution street/Roadway luminaire, with driver, including electric connection, complete fitting with all accessories and following specifications and all as directed:- (a) Lumen system efficacy of luminaire should be minimum 110 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : Max10%. (f) CRI : minimum 70 and CCT : 5700 K. (g) IP rating : IP66. (h) IK rating : Minimum IK07 (j) Built in potted LED Driver of the make as of the luminaire. (k) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (l) Surge protection 10 kV (inbuilt + extended) (m) Lens - High Efficiency wide angle lens. (n) BIS Approved fixtures and driver (o) Rated life time : 50000 burning hrs (Average 10 to 12 hrs daily)

Material and labour for Brackets made out of GI tubing light grade 40mm dia, 1.5 metre long bent to shape at 120 degree angle at half metre from bottom, including two Nos clamps made out of MS Flat iron size 50x3 mm for fixing of bracket on steel tubular/ PCC poles with suitable nuts and bolts including painting to MS clamp and nut bolts with two coats of aluminium paint over a coat of red oxide primer complete all as specified and as directed.

Supply and fixing Junction box of size 200x160x98mm/200x140X95mm or any other higher size (pole mounting) and should be insulated and made out of polycarbonate with glass fiber re-inforced material having IP66 protection in accordance with IEC 60529, fixing with and including clamp made out of MS Flat iron size 25x3 mm including suitable size of nuts, bolts and washers including painting to MS clamp and nut bolts with two coats of aluminium paint over a coat of red oxide primer complete comprising of the following and as directed:- Note :- (a) Junction Box must meet the provision laid down in IEC 60998-1, IEC-60670-22, IEC-60670-22, IEC 60670-2 to 5 and color according to RAL 9011. (b) The manufacturer of junction box shall submit a copy of IEC certificate. (c) Junction box shall be fire retardant and self extiguishing in accordance with IEC60695-2to 11, DIN VDE 0304 Part-3, UL94 V-2 flammability standard. It should be tested at Glove Wire test for 960°C. (d) The degree of protection of enclosure against mechanical load shall be in accordance with EN 50298 for IK08. (e) Internally embedded gasket of polyurethane. (f) Junction box shall 4 pole complete with single pole MCB 'C' curve of 6 Amp, rating.

Supply and fixing 1100 Volt grade, PVC insulated, stranded aluminium conductor cable, PVC sheathed 2.5 Sqmm flat or circular twin core for service connections drawn through pipe including making electric connections complete all as specified and as directed. Note ;- Pipe shall be measured and paid separately under respective item of BOQ.

Supply and fixing mild steel stove enamelled conduit of size 20 mm dia fixed along PCC/steel tublar street light pole with clamps made out of MS Flat iron size 25x3 mm at not more than 100cm c/c matching with section of pole, including suitable size of nuts, bolts and washers including painting to MS clamp and nut bolts with two coats of aluminium paint over a coat of red oxide primer complete all as specified and as directed. (Cable shall be measured and paid separately under appropriate item of Sch)

Material and labour for shifting of transformer of capacity 11/0.433KV, 100KVA including dehydration and top up transformer oil upto the appropriate level with standard dielectric strength including handling and transporting of transformer from Bikaner to proposed site at MFFR place of installation and installing on existing 2/4 pole structure or plateform /plinth with necessary fixing arrangement including necessary pcc repair work and connecting input and output electricity connections with minor spares, commissioning and testing complete all as specified and as as directed. Note:- (i) Cost for taking down, loading/unloading, shifting transport/T&P (crane and vehicle) for shifting to transformer from Bikaner to proposed site at MFFR (Approx 190 KM) and transformer oil upto 10 ltrs required for top up shall deemed to be included in the quoted unit rate, nothing shall be paid extra on this account. (ii) Incase damage of transformer during to the shifting, which panelty recovery cost of transformer shall be made from the contractor payment as per directed. (iii) Transformer will be issued by the department to contractor for shifting under Sch 'B' free for installation.

Subtotal

Lump sum price worked out by the tenderer for “Excavation and Earth work" as listed in Schedule ‘A’ Section - VI.

RAJENDER ENTERPRISES

A S CONSTRUCTION COMPANY

M/s Mohata Buildcon

UNITED SAINI BUILDERS

Dasmesh Buildcon

Jagdish Prashad and Company