PROVISION OF HANGAR COMPLEX ALONGWITH CONNECTED SERVICES UNDER GE(AF) JORHAT

Amount

SCHEDULE 'A' PART - I (BUILDING WORKS) Details of prepriced Schedule is given in tender documents.

SCHEDULE 'A' PART- II (EARTH WORK) Details of prepriced Schedule is given in tender documents.

SCHEDULE 'A' PART- III (INTERNAL ELECTRIFICATION) Details of prepriced Schedule is given in tender documents.

SCHEDULE 'A' PART- IV (INTERNAL WATER SUPPLY) Details of prepriced Schedule is given in tender documents.

SCHEDULE 'A' PART-V (ROAD/TAXI TRACK) Details of prepriced Schedule is given in tender documents.

SCHEDULE 'A' PART- VI (AREA DRAINAGE) Details of prepriced Schedule is given in tender documents.

SCHEDULE 'A' PART- VII (SEWAGE DISPOSAL ) Details of prepriced Schedule is given in tender documents.

SCHEDULE 'A' PART- VIII (PUMP HOUSE) Details of prepriced Schedule is given in tender documents.

SCHEDULE 'A' PART- IX (FIRE ALARM) Details of prepriced Schedule is given in tender documents.

SCHEDULE 'A' PART- X (FIRE FIGHTING) Details of prepriced Schedule is given in tender documents.

SCHEDULE 'A' PART- XI (EXTERNAL WATER SUPPLY) Details of prepriced Schedule is given in tender documents

SCHEDULE 'A' PART- XII (EXTERNAL ELECTRIFICATION) Details of prepriced Schedule is given in tender documents

SCHEDULE 'A' PART-XIII (LIGHTENING PROTECTION) Details of prepriced Schedule is given in tender documents

SCHEDULE 'A' PART-XIV (WATER COOLER AND AIR CONDITIONING) Details of prepriced Schedule is given in tender documents

SCHEDULE 'A' PART-XV (SOLAR WATER HEATING SYSTEM) Details of prepriced Schedule is given in tender documents

SCHEDULE 'A' PART-XVI (DEMOLITION / DISMANTLING) Details of prepriced Schedule is given in tender documents

SCHEDULE 'A' PART -XVII (MISCELLANEOUS ITEMS) Note:- This schedule is not pre-priced by MES.

INTERNAL ELECTRIFICATION M & L for sub main wiring with 2 runs of single core 2.5 Sqmm (Nominal area) PVC insulated unsheathed multi-stranded copper conductor cable LT 1100 Volts grade (FR-LSH), drawn through in and including concealed heavy duty PVC rigid conduit pipe of required size with accessories including earth continuity conductor using PVC insulated unsheathed copper conductor cable with 1 run of single core 2.5 Sqmm (Nominal area) (FR-LSH) connected to common earth dolly complete all as specified and as directed. Notes: 1. 3 runs of 2.5 sqmm and one run of concealed heavy duty PVC rigid conduit pipe with accessories shall be measured as one run length. 2. Cutting chases, making good disturbed surface shall be included in quoted lump sum of schedule 'A' Part-I and nothing extra shall be paid on this account.

M & L for sub main wiring with 2 runs of single core 6.0 Sqmm (Nominal area) PVC insulated unsheathed multi-stranded copper conductor cable LT 1100 Volts grade (FR-LSH), drawn through in and including concealed heavy duty PVC rigid conduit pipe of required size with accessories including earth continuity conductor using PVC insulated unsheathed copper conductor cable with 1 run of single core 6.0 Sqmm (Nominal area) (FR-LSH) connected to common earth dolly complete all as specified and as directed. Notes: 1. 3 runs of 6.0 sqmm and one run of concealed heavy duty PVC rigid conduit pipe with accessories shall be measured as one run length. 2. Cutting chases, making good disturbed surface shall be included in quoted lump sum of schedule 'A' Part-I and nothing extra shall be paid on this account.

M & L for sub main wiring with 2 runs of single core 10.0 Sqmm (Nominal area) PVC insulated unsheathed multi-stranded copper conductor cable LT 1100 Volts grade (FR-LSH), drawn through in and including concealed heavy duty PVC rigid conduit pipe of required size with accessories including earth continuity conductor using PVC insulated unsheathed copper conductor cable with 1 run of single core 10.0 Sqmm (Nominal area) (FR-LSH) connected to common earth dolly complete all as specified and as directed. Notes: 1. 3 runs of 10.0 sqmm and one run of concealed heavy duty PVC rigid conduit pipe with accessories shall be measured as one run length. 2. Cutting chases, making good disturbed surface shall be included in quoted lump sum of schedule 'A' Part-I and nothing extra shall be paid on this account.

M & L for sub main wiring with 2 runs of single core 16.0 Sqmm (Nominal area) PVC insulated unsheathed multi-stranded copper conductor cable LT 1100 Volts grade (FR-LSH), drawn through in and including concealed heavy duty PVC rigid conduit pipe of required size with accessories including earth continuity conductor using PVC insulated unsheathed copper conductor cable with 1 run of single core 16.0 Sqmm (Nominal area) (FR-LSH) connected to common earth dolly complete all as specified and as directed. Notes: 1. 3 runs of 16.0 sqmm and one run of concealed heavy duty PVC rigid conduit pipe with accessories shall be measured as one run length. 2. Cutting chases, making good disturbed surface shall be included in quoted lump sum of schedule 'A' Part-I and nothing extra shall be paid on this account.

M & L for sub main wiring with 2 runs of single core 25.0 Sqmm (Nominal area) PVC insulated unsheathed multi-stranded copper conductor cable LT 1100 Volts grade (FR-LSH), drawn through in and including concealed heavy duty PVC rigid conduit pipe of required size with accessories including earth continuity conductor using PVC insulated unsheathed copper conductor cable with 1 run of single core 16.0 Sqmm (Nominal area) (FR-LSH) connected to common earth dolly complete all as specified and as directed. Notes: 1. 2 runs of 25.0 sqmm, 1 run of 16.0 Sqmm and one run of concealed heavy duty PVC rigid conduit pipe with accessories shall be measured as one run length. 2. Cutting chases, making good disturbed surface shall be included in quoted lump sum of schedule 'A' Part-I and nothing extra shall be paid on this account.

S & F of factory made sheet metal enclousure, double door designed vertical type, TPN, DB, 4 Way, IP 54 with 200 Amp bus bar, neutral link,dinrail with provision of MCCB as incommer and TPN/DP/SP MCBs as outgoing, complete, all as specified and directed. Note: MCCB & MCBs will be measured and paid separately.

S & F of factory made sheet metal enclousure, double door designed vertical type, TPN, DB, 6 Way, IP 54 with 200 Amp bus bar, neutral link,dinrail with provision of MCCB as incommer and TPN/DP/SP MCBs as outgoing, complete, all as specified and directed. Note: MCCB & MCBs will be measured and paid separately.

S & F of MCCB, 04 pole, 160 Amps, 415 Volt, breaking capacity 36 KA, including necessary incoming and outgoing electric connection with suitable size of copper lugs, complete, all as specified and directed.

S & F of MCCB, 04 pole, 63 Amps, 415 Volt, C series, breaking capacity 36 KA, including necessary incoming and outgoing electric connection with suitable size of copper lugs, complete, all as specified and directed.

S & F of MCB, DP, 32 Amps, 240 Volt, 50 Hz, C series, breaking capacity 10 KA, including necessary incoming and outgoing electric connection with suitable size of copper lugs, complete, all as specified and directed.

S & F of MCB, DP, 40 Amps, 240 Volt, 50 Hz, C series, breaking capacity 10 KA, including necessary incoming and outgoing electric connection with suitable size of copper lugs, complete, all as specified and directed.

S & F of MCB, DP, 63 Amps, 240 Volt, 50 Hz, C series, breaking capacity 10 KA, including necessary incoming and outgoing electric connection with suitable size of copper lugs, complete, all as specified and directed.

S & F of MCB, SP, 6 to 32 Amps, 240 Volt, 50 Hz, B series, breaking capacity 10 KA, including necessary incoming and outgoing electric connection with suitable size of copper lugs, complete, all as specified and directed.

S & F of MCB, SPN, 6 to 32 Amps, 240 Volt, 50 Hz, C series, breaking capacity 10 KA, including necessary incoming and outgoing electric connection with suitable size of copper lugs, complete, all as specified and directed.

S & F of RCCB, 63 Amps, 30 mA 240 Volt, 50 Hz, C series, including necessary incoming and outgoing electric connection with suitable size of copper lugs, complete, all as specified and directed.

S & F of AC circuit breaker, DP, 100 Amps, 240 Volt, 50 Hz, C series, breaking capacity 10 KA, including necessary incoming and outgoing electric connection with suitable size of copper lugs, complete, all as specified and directed.

S & F of LED tube light fitting, 1 x 20W including LED light with entire assembly, pre-wired, complete with connecting lead of PVC insulated copper wire, suitable for 230 Volts, mounted on ceiling/wall and providing continuous earth wire, complete, all as specified and directed.

S & F of LED highbay luminaries, 200 Watt, operating voltage 130 to 280 Volts, lumen efficiency not less than 120 lumen Watt, pre-wired, complete with connecting lead of PVC insulated copper wire, mounted on ceiling/wall and providing contnuous earth wire, complete, all as specified and directed.

S & F of LED security light fitting 1 x 40 Watt including LED light, Integral reflector made of alluminum alloy LM6, prewired, complete with connecting lead of PVC insulated copper wire, mounted on ceiling/wall and providing contnuous earth wire, complete, all as specified and directed.

S & F of ceiling fan, 5 star rated, 1200 mm sweep, 240 volt AC, including down rod of suitable size, connected with twin core twisted flexible wire copper conductor cable with suitable size from ceiling rose to fan, complete, all as specified and directed.

S & F of metal exhaust fan, 300 mm sweep, single phase, 240 volt AC, with louvers, connected with twin core twisted flexible wire copper conductor cable with suitable size from ceiling rose to fan, complete, all as specified and directed.

M & L for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised earth wire of size 4 mm dia by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe 15 mm bore (medium grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) including testing, complete, all as specified and directed.

INTERNAL WATER SUPPLY S & F of 15 mm bore angular stop cock, brass, chromium plated, screwed down, high pressure with crutch or butterfly handle with long shank and cup, screwed for iron pipe, complete, all as specified and directed.

S & F of 15 mm bore Bib tap, brass, chromium plated, screwed down, high pressure with crutch or butterfly handle with long shank and cup, screwed for iron pipe, complete, all as specified and directed.

S & F of 15 mm bore Bib Cock, 2 way, brass, chromium plated, screwed down, high pressure with crutch or butterfly handle with long shank and cup, screwed for iron pipe, complete, all as specified and directed.

S & F of Health faucet chromium plated with 8 mm dia, 1 mtr long CP tube screwed down, complete, all as specified and directed

S & F of Toilet paper holder, brass, chromium plated, complete, all as specified and directed.

ROAD/TAXI TRACK/HANGAR FLOOR M & L for bringing approved earth from outside MOD land and depositing where directed including loading and unloading, complete, all as specified and directed.

M & L for Bituminous premix dense concrete 40mm consolidated thickness with binder content as per design mix, rolled and compacted to required camber and gradient, complete, all as speicified and directed.

M & L for 200 mm thick spread thickness Granular sub base Gde-I of table 400-1 of MORTH, IRC specification in 2 layers of 100mm thick each using with stone aggregate of specified grading including spread, rolled by tandam vibratory roller and transverse gradient (1:100) for achive field com[paction and consolidation to gradient and camber required with mechanical paver /grader, complete, all as speicified and directed.

M & L for 150 mm thick spread thickness Granular sub base Gde-I of table 400-1 of MORTH, IRC specification in single layer using with stone aggregate of specified grading including spread, rolled by tandam vibratory roller and transverse gradient (1:100) for achive field com[paction and consolidation to gradient and camber required with mechanical paver /grader, complete, all as speicified and directed.

M & L for providing and laying 150 mm thick (compacted thickness) (in two layers of 75 mm compacted thick each) Wet Mixed Macadam (WMM), using gradings requirement of aggregate as per Table 400-II of yellow book of MORTH using mechanical paver and rolled with power roller of 8-10 tonne capacity of required camber and gradient, complete, all as speicified and directed.

M & L for Providing and laying 150 mm thick (average) dry lean concrete (DLC) over a prepared subgrade with coarse and fine aggregate confirming to IS:383, size of aggregate not exc 40 mm (grading and other parameters as per table 600-I of latest MORTH, IRC : SP : 49 Specification), of design mix, minimum cement content shall not leass than 250kg/Cum mixed in fully automatic computerised concrete batching plant, transported to site laid with sensor paver including spreading and compacted by using 8 to 10 tones vibratory roller with and including necessary formwork finishing etc, complete, all as specified and directed.

M & L for high density polythene film (transperent colour) in single layer of 400 Micron thickness virgin quality as per ASTMD 2103/IS 2508 laid with side and ovelapping not less than 300mm, complete, all as specified and directed.

M & L for polyurethane paint over hanger flooring, 3mm EPU system (100mm micron primer, 2mm epoxy screed, 1mm self levelling EPU top coat) of approved make including cleaning the exisitng surface, all as per manufacturers instructions, complete, all as specified and directed.

Supply only Polyester non circular synthetic fibre, 6/12mm long with circum-circle diameter 30-35micron, designed for melting point 240-260 degree Celsius and having specific gravity 1.34 to 1.40 etc, complete, all as specified and directed. Make:- Reliance (Recron 3S) or equivalent as approved make as per list of make.

M & L for Forming 20mm wide expansion joint for full depth of PQC and filled with pre-formed expandable synthetic filler board of approved make, provision of closed cell, medium density, cross linked polyurethene foam back up rod of 20 mm dia and filled with pitch free polyurethene grey sealant (minimum depth of sealant above back up rod shall be 25 mm) conforming to BS-5212 (Type FB) priming the sides as recommended by manufacturers instructions and applying masking tapes on edges of joint to prevent accidental spillage of sealant and removing the masking tapes after sealant is applied, the sealant should have MAF + 30% as used in international Airport in India, complete, all as specified and directed.

M & L for Forming dummy joint using diamond cutter with initial saw cut with 3 mm blade soon after concrete sets for the depth of 127 mm, widening the first saw cut to 8 mm wide and 25 mm deep from top, priming top 15 mm with approved primer, applying masking tape on edges of joint to prevent accidental spillage of sealant and filling with polurethane /polysuphide based sealant MAF + 30% (BS-5212) to closed cell, medium density, cross linked polethylene foam back up rod of 10 mm dia, for complete width of the joint and removing the masking tape after filling of sealant and as specified and as per manufacutrer directions, complete, all as specified and directed.

M & L for Forming construction joint 28mm deep x 10mm wide using diamond cutter with closed cell, medium density, cross linked polyethene foam back up rod of 12mm dia applying bond breaker tape on top of back up rod for complete width of the joint, priming top 10 mm with specified primer and filling with polyurethane based sealant (BS 5212), applying masking tape on edge of joint to prevent accidental spillage of sealant and removing the masking tape after filling of sealant and as specified and as per the directions of the manufacturer, complete all as specified and directed.

M & L for 2.5mm thick retro reflective thermoplastic road marking paint conforming to MOST, AASHTO, M249 and BS 6088 after preparation of surfaces, complete, all as specified and directed.

SEWAGE DISPOSAL Construction of septic tank for 100 users, complete, all as specified and as shown on drawings.

Construction of septic tank for 10 users, complete, all as specified and as shown on drawings.

Construction of soakage well of size 1.80m dia. & 3.00m deep, complete, all as specified and as shown on drawings.

Construction of soakage well of size 1.20m dia. & 3.00m deep, complete, all as specified and as shown on drawings.

FIRE ALARM Supply and installing the flowchart based programmable RTU alongwith battery back up for incase of power fail SMS and wireless modem suitable for GSM/GPRS based communication system, to be mounted in RTU enclosure with the following:- (a) Input/Output as per requirement (b) 3 Serial port (c) Digital Inputs(Optical Isolation) (d) Digital Outputs (e) Isolated Analog Inputs (f) Local display, Membrane key board and data storage (g) Compatability with GSM modem (h) Isolation transformer for RTU protection-01 No. (j) One panel in each FACP and one panel for fire section with mimik panel.

S & F of addressable type flame detector, indoor type, complying with and type certified to EN-45 with quad band (triple IR + visible) technology (add p cost of module to be a complete set, the type of the module shall be realy type module) with self built intelligence as per IS:11360, complete, all as specified and directed.

S & F of Mimic panel using LED indicator for fault and fire alarm monitoring, complete, all as specified and directed.

FIRE FIGHTING Supply and laying in trenches Ductile Iron (DI) flanged pipes, centrifugally cast, CLASS K-9, conforming to IS:8329-2000 with internal metallic zinc coating and external black bitumen coating suitable for flanged type joint in any length of 150mm bore including all jointing materials and fittings, complete, all as specified and directed.

Supply and laying in trenches Ductile Iron (DI) flanged pipes, centrifugally cast, CLASS K-9, conforming to IS:8329-2000 with internal metallic zinc coating and external black bitumen coating suitable for flanged type joint in any length of 100mm bore including all jointing materials and fittings, complete, all as specified and directed.

S & F of Ductile Iron (DI) fittings such as bends (any radius & angle), tapers any type (straight bands, increasing, decreasing or double socketetc.), tee piece, single branches, Y junction, double branches, cross, cap plug etc, centrifugally cast, CLASS K-9, conforming to IS:8329-2000 with internal metallic zinc coating and external black bitumen coating, complete, all as specified and directed.

S & F in foot valve conforming to IS:4038, 150mm dia, complete, all as specified and directed.

M & L for construction of brick masonary valve pit of size 120cm x 120 cm x 120 cm (internal dimensions) with one brick thick wall in cement mortar (1 : 4) on 100 mm thick PCC (1:4:8) D2 (using 40 mm graded broken stone aggregate) as in foundation lean concrete, including PCC (1:3:6) type C1 (using 20 mm graded crushed stone aggregate) as in beding and coping and 10 mm thick cement plaster in CM (1:4) internally and externally upto 15 cm below ground level providing valve pit 50 mm X 50 mm X 6 mm angle iron frame all round the fixed point by means of 04 Nos holdfast 150 mm long made out of flat iron 40 mm X 6 mm embedded in PCC block (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) of size 250 mm X 200 mm X 150 mm including provision of hinges welded with Mild Steel cover 3 mm thick, MS handle of suitable and size welded with MS cover and suitable locking arrangement including 65 mm dia Godrej pad lock and 3 Nos. key and applying two coats synthetic enamel paint over a coat of red oxide primer on steel surface including necessary excavation and earth work in soft/loose soil, complete, all as specified and directed.

S & F of MS ERW fittings such as bends (any radius & angle), tapers any type (straight bands, increasing, decreasing or double socketetc.), tee piece, single branches, Y junction, double branches, cross, cap plug etc, complete, all as specified and directed.

M & L for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised strip of size 32 mm x 6 mm by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe 40 mm bore (medium grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) including testing on completion, complete, all as specified and directed.

M & L for making fire point with the following items, complete, all as specified and directed:- (a) Mechanical foam extinguisher of capacity 9.0 Litres as per IS:15683 - 02 No. (b) Wheeled fire extinguisher CO2 type, 25 Kg capacity as per IS:16018 - 01 No. (c) Wheeled mechanical foam extinguisher, 45 Litres capacity, trolly mounted type as per IS:16018 - 01 No. (d) Wheeled dry powder fire extinguisher, 25 Kg capacity as per IS:16018 - 01 No. (e) Dry powder fire extinguisher, 9 Kg capacity as per IS:16018 - 02 No.

S & F of RRL hose type - A, 30m long, complete, all as specified and directed.

Design supply, installation, testing and commissioning of automatic foam extinguishing system having a foam tank made of stainless steel of capacity 4500 Ltrs or more as per design having inductions delivery for hangar, solenoid valves operations through detectors of automaic fire larm system (smoke detectors), seamless connections, GM couplings with builtin tvrv housed in MS box with front glass, complete, all as specified and directed.

S & F of water cum foam monitors of size 63mm as per IS:8442, standpost type with material of construction being in carbon steel/stainless stell with flanged inlet with jet and spray type hydro foam nozzle/ aluminum barrel type 63mm size, suitable for operation at pressure of 100PSI, complete, all as specified and directed.

S & F of fabrication header, 01 meter long, made out of 300mm dia MS heavy duty pipe, welding dead cap on both ends, provisioning of 04 inlet connections of 150mm dia pipes & 02 outlet connection of 150mm, complete, with painting two coats of red paint over a coat of red oxide primer, complete, all as specified and directed.

S & F of fabrication header, 01 meter long, made out of 200mm dia MS heavy duty pipe, welding dead cap on both ends, provisioning of 01 inlet connection of 100mm dia pipes & 02 outlet connection of 100mm, complete, with painting two coats of red paint over a coat of red oxide primer, complete, all as specified and directed.

Supply, Install, Testing & Commissioning of terrace pumset, 440 V, 3 pahse, 50 Hz confirming to IS-1988 with CI casing, bronze impeller and stainless steel shaft mounted on heavy duty bearing suitable for 450LPM discharge at 36m head with star-delta starter control panel for automatic operation.

M & L for maikng fire point with shed comprising of the following items:- (a) Mechanical foam extinguisher of capacity 9.0 Ltrs complete all as per IS:15683-02 No. (b) Light weight squeeze grip type CO2 fire extinguisher 3 Kg capacity all as per IS:16018 - 02 No. (c) Dry powder (ABC) type fire extinguisher of capacity 6 Kg all as per IS:15683 - 02 No.

EXTERNAL WATER SUPPLY M & L for construction of brick masonary valve pit of size 100 cm x 100 cm x 100 cm (internal dimensions) with one brick thick wall in cement mortar (1 : 4) on 100 mm thick PCC (1:4:8) D2 (using 40 mm graded broken stone aggregate) as in foundation lean concrete, including PCC (1:3:6) type C1 (using 20 mm graded crushed stone aggregate) as in beding and coping and 10 mm thick cement plaster in CM (1:4) internally and externally upto 15 cm below ground level providing valve pit 50 mm X 50 mm X 6 mm angle iron frame all round the fixed point by means of 04 Nos holdfast 150 mm long made out of flat iron 50 mm X 6 mm embedded in PCC block (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) of size 250 mm X 200 mm X 150 mm including provision of hinges welded with Mild Steel cover 3 mm thick, MS handle of suitable and size welded with MS cover and suitable locking arrangement including 65 mm dia Godrej pad lock and 3 Nos. key and applying two coats synthetic enamel paint over a coat of red oxide primer on steel surface including necessary excavation and earth work in soft/loose soil complete, all as specified and directed.

Supply and laying in trenches Ductile Iron (DI) pipes with spigot & socket ends, centrifugally cast, CLASS K-9, conforming to IS:8329-2000 with internal metallic zinc coating and external black bitumen coating suitable for push on TYTON joint in any length of 80mm bore including all jointing materials and fittings, complete, all as specified and directed.

Supply and laying in trenches Ductile Iron (DI) pipes with spigot & socket ends, centrifugally cast, CLASS K-7, conforming to IS:8329-2000 with internal metallic zinc coating and external black bitumen coating suitable for push on TYTON joint in any length of 100mm bore including all jointing materials and fittings, complete, all as specified and directed.

Supplying, installing, commissioning and testing of monoblock pump set, size 80/80mm of suction/ delivery with discharge of 5 LPS at 30 m head with CI casing, bronze impeller and stainless steel shaft, 415 volts, 50 Hz AC, including PCC fooundation and suitable starter, complete, all as specified and directed.

S & F of foot valve conforming to IS:4038 of size 80 dia. complete, all as specified and directed.

M & L for boring holes under road, pavement, hard standing by mechanical/manual auguring including HDPE pipe of 250mm dia suitable for 0.4 Mpa working pressure for crossing the waterline through hanger roads etc., complete, all as specified and directed.

EXTERNAL ELECTRIFICATION Supply, installation, testing and commissioning of HT 12KV SF-6 insulated metal enclosure, Outdoor type, RMU with standard metering unit having digital display, 3 phase, 50 cycle, rated short time current 21 KA/3 Sec, rated bus bar current of 630A, 3 way ( 1 No. incoming load break switch and 2 No. outgoing 630 Amp vaccum circuit breaker) with self powered (3 O/C & 1 E/F) relays with in-built 11 KV CTs (03 No.) having CT ratio 50/1, accuracy Class-1.0 for metering and03 Nos 11 KV CT with CT ratio 50/1, SP10, 2.5 VA for for protection purpose & 11 KV resin cast PTs (03 No.). All relays & metering equipments shall be functional with 24 volts DC protection supply. The RMU unit should be designed, manufactured and tested according to IEC 60694, IEC 62271-102, IEC62271-100, IEC 62271-200, IEC 60265-1, IEC-60529. The ring main unit comprises of the following:- (a) 01 Nos incoming Load Break Switch with the following specifications:- (i) Manually operated 12 KV, 630A, Load Break switch and earthing switch with making capacity " Live cable" LED indicators through capacitor. (ii) Voltage driver mounted on the bushings. (iii) Mechanical on/off/earth indication cable testing facility without disconnecting the cable terminals. (iv) Anti-reflex operating handle. (v) Cable box suitable for cable termination upto 1 No. 3 core 300 Sqmm XLPE cable. (vi) Cable door should be arc proof and interlocked with respective earthing switches for safety operation. It should not be possible to open the cable and the cable door unless the switch is ON.

Supply and install, testing & commission self supporting outdoor type totally enclosed LT panel of suitable size, compartmentalized design , IP65 dust and and vermin proof of suitable size for 440 volt , 3 phase , 4 wire system made out of 3.15mm thick CRCA sheet and built up on rigid frame work of having front and rear hinged doors with neoprence rubber gasket including danger plate, earthing strip point and ventilation louvers at the rear side bottom detachable gland plate complete with suitable size of zinc / chromium plate and nuts bolts, and washers etc,. the panel shall be powder coated and treated with 7 tank process and incoming / outgoing cable holes fitted with cable glands at the bottom. The panel shall be embedded with 50 x 50 x 6 mm MS angle iron frame and 30 cm above the normal ground level complete with suitable size foundation with PCC(1:24) type B2 fitted with following accessories complete all as specified and directed by engr-in- charge (Loc Main Panel) Note : all internal connection of MCCB from bus bar made by using aluminum bus bar of rated capacity (a) Aluminum bus bar 1500 amps -04 NOS, supported with suitable size of heavy duty PVC stand lock with suitable size of brass nut , bolts and washer with heat shrinkable PVC sleeving, the bar shall be colour coded (red, yellow and blue ) for three Phases and black for neutral (b) ACB 1000 Amps 415 volts, 50 KA breaking capacity 4 pole fixed type duly connected to bus bar -01 No.(Incoming cable gland plate with holes suitable for 04 No. single core 1000Sqmm)

Supply, Install, Testing & Commissioning Self supporting outdoor types totally enclosed LT Feder Filler of suitable size, compartmentalized design, IP 65 dust varmin proof of Suitable size suitable for 440 volt, 3 Phase , 4 wire System made out 3.15 mm thick CRCA sheet and built upon rigid frame work of having front and rear hinged doors with neoprence rubber gasket including danger plate, earthing strip point and ventilation louvers at the rear side bottom detachable gland plate complete with suitable size of zinc / chromium plate and nuts bolts, and washers etc,. the panel shall be powder coated and treated with 7 tank process and incoming / outgoing cable holes fitted with cable glands at the bottom. The panel shall be embedded with 50 x 50 x 6 mm MS angle iron frame and 30 cm above the normal ground level complete with suitable size foundation with PCC(1:2:4) type B2 fitted with following accessories complete all as specified and directed by engr-in- charge (Loc :FPB-1) Note : all internal connection of MCCB from BUS bar made by using aluminum bus bar of rated capacity (a) Aluminum bus bar 600 amps -04 Nos , supported with suitable size of heavy duty PVC stand lock with suitable size of brass nut, bolts and washer with heat shrinkable PVC sleeving , the bar shall be colour coded (red , yellow and blue ) for three for phases and black for neutral (b)MCCB 400 amps 415 volts , 35 KA breaking capacity 4 pole duly connected to bus bar as incoming - 01 NO

Supply, Install, Testing & Commissioning Self supporting outdoor types totally enclosed LT Feeder Filler of suitable size, compartmentalized design, IP 65 dust & vermin proof of Suitable size suitable for 440 volt, 3 Phase , 4 wire System made out 3.15 mm thick CRCA sheet and built upon rigid frame work of having front and rear hinged doors with neoprence rubber gasket including danger plate, earthing strip point and ventilation louvers at the rear side bottom detachable gland plate complete with suitable size of zinc / chromium plate and nuts bolts, and washers etc. the panel shall be powder coated and treated with 7 tank process and incoming / outgoing cable holes fitted with cable glands at the bottom. The panel shall be embedded with 50 x 50 x 6 mm MS angle iron frame and 30 cm above the normal ground level complete with suitable size foundation with PCC(1:2:4) type B2 fitted with following accessories complete all as specified and directed by Engr-in- charge (Loc :FPB-2) Note : All internal connection of MCCB from BUS bar made by using aluminum bus bar of rated capacity (a) Aluminum bus bar 600 amps -04 Nos , supported with suitable size of heavy duty PVC stand lock with suitable size of brass nut, bolts and washer with heat shrinkable PVC sleeving , the bar shall be colour coded (red , yellow and blue ) for three for phases and black for neutral (b) MCCB 400 amps 415 volts , 36 KA breaking capacity 4 pole duly connected to bus bar as incoming - 01 NO

S & F of XLPE insulated, armoured, heavy duty electric cables with aluminium conductor, 1100 Volts grade, Cross sectional area 1000Sqmm x Single core, complete, all as specified and directed .

M & L for boring holes under road, pavement, hard standing by mechanical/manual auguring including RCC pipe Class NP3, 250mm dia., complete, all as specified and directed.

M & L for Sub Class 'B' Bricks laid dry, falt over cable perpendicular across the cable in trenches for cable protection, complete, all as specified and directed.

S & F of 150 LED flood light fitting, 3rd generation, ultra sleek, light weightand with secondary optics made of pressure die cast housing with IP66 rating including brackets and clamps, complete, all as specified and directed .

S & F of LED aviation obstruction light luminaries comprising of aluminium housing with polycarbonate enclosure including electrical connection, complete, all as specified and as directed.

S & F of industrial wall mounted plug suitable for IP67 degree of protection, 32 Amps rating, 3P+N+E, complete, all as specified and as directed.

Supply and installation of electo zinc galavanised wire mesh indoor cable tray in accordance with standard BSEN 12329-2000 with all mounting accessories . All trays should be 3005 mm long . Cable tray shall be manufactured from steel wire , welded together and bent into final shape prior to surface treatment steel wire cable try should be produced from lateral and longitudinal side wall steel wires, with minimum diameters between 3.7 to 5.9mm from trays depending on the widths of the trays as per the design parameters . Trays should be manufactured with a 54 mm x 100 mm mesh configuration . trays should be coupled together using fast spring coupler the coupling will have the same surface finish as the tray . Loading and deflection characteristic of the tray should be tested and the result published in accordance with the European standard IEC 61537 . FIRE test certification should be published in accordance with the E30/ E90 standard , Electrical continuity across a coupling should be demonstrated by means of a publication test method and result, complete, all as specified and directed.

Supply and installation of electo zinc galavanised wire mesh outdoor cable tray in accordance with standard BSEN 12329-2000 with all mounting accessories . All trays should be 3005 mm long . Cable tray shall be manufactured from steel wire , welded together and bent into final shape prior to surface treatment steel wire cable try should be produced from lateral and longitudinal side wall steel wires, with minimum diameters between 3.7 to 5.9mm from trays depending on the widths of the trays as per the design parameters . Trays should be manufactured with a 54 mm x 100 mm mesh configuration . trays should be coupled together using fast spring coupler the coupling will have the same surface finish as the tray . Loading and deflection characteristic of the tray should be tested and the result published in accordance with the European standard IEC 61537 . FIRE test certification should be published in accordance with the E30/ E90 standard , Electrical continuity across a coupling should be demonstrated by means of a publication test method and result .

LIGHTENING PROTECTION S & F of GI Pipe, medium grade, 25mm dia., duly grouted on the roof for fixing air terminals including nuts and bolts as per IS:2309, complete, all as specified and directed.

WATER COOLER AND AIR CONDITIONING S & F of voltage stabilizer for automatic operation, single phase, naturally air cooled, indoor type & designed for input vatiation between 170 V to 250 V with output voltage stabilized at 230V with accuracy of + 2.5% and of capacity 4.0KVA, complete, all as specified and directed.

S & F of voltage stabilizer for automatic operation, single phase, naturally air cooled, indoor type & designed for input vatiation between 170 V to 250 V with output voltage stabilized at 230V with accuracy of + 2.5% and of capacity 5.0KVA, complete, all as specified and directed.

S & F of voltage stabilizer for automatic operation, single phase, naturally air cooled, indoor type & designed for input vatiation between 170 V to 250 V with output voltage stabilized at 230V with accuracy of + 2.5% and of capacity 1.0KVA, complete, all as specified and directed.

S & F of Refrigerators, electric driven, single phase, capacity of more than 310 litres upto 360 litres, BEE 5 star rated, complete, all as specified and directed.

AIR CIRCULATOR S & F of Air circulator fan, 230 volt, single phase, oscillating 750mm sweep and ir delivery 22,200 CM per hour, suitable for wall mounting, complete, all as specified and directed.

DEMOLITION/DISMANTLING Taking down tube light fitting/flood light fitting of any capacity from exisitng wall/ ceiling, complete, all as specified and directed.

Taking down submain wiring of any size from exisitng wall/ ceiling, complete, all as specified and directed.

Dismantling of old DBs, any size, complete, all as specified and directed.

Dismantling of old unserviceable air termination, any size, complete, all as specified and directed.

Dismantling of old unserviceable aluminium strip, any size, complete, all as specified and directed.

Dismantling of old unserviceable LT panel, any size, complete, all as specified and directed.

Taking down ceiling fan/ exhaust fan from exisitng wall/ ceiling carefully and depositing to MES store yard, complete, all as specified and directed.

CHEMICAL EARTHING Supply, installation and testing of advanced encapsulatedcompound based, maintenance free, pipe-in-pipe technology upgraded (Zinc & Alloy coated), Zinc coated (80-100 microns) with pure zinc (99.9%) & Alloy coating (200-250 microns). Earth system should confirming as per IS:3043. The outer and inner pipe should be 48.3mm & 26.4 mm with 3 metres in length, Zinc coated with additional special alloy coating 300mm on the top side for aditional corrosion protection of the terminal. The annular space between the pipes being filled up with COMPACT FILL (CF) (cystalline conductive compound). The COMPACT FILL (CF) mixture which is machine pressed in the pipes should not disintegrate or collapse when outer pipe corrodes. The inner pipe should be extended with terminals for connectivity. The job includes digging the pits by rotary method and refilling the same by electrodite/conductolite back fill compound (ground enhancer), the BFC should be eco-friendly and should not contain environmentally hazardous material/metal having RoHS certification from NABL accredited lab. Good earth is to be arranged to fill the excavated pits by mixing the same with BFC2 bags(as per site condition) including PCC pit in cement concrete 1:3:6 (using 20mm graded stone aggregate) and RCC cover of size 450 x 450 x 50mm in RCC 1:2:4 (using 20mm graded stone aggregate) reinforced with and including 8mm dia TMT bars @ 100mm C/C both ways, complete, all as specified and directed.

M & L for earthing complete with copper plate electrode 300 mm x 300 mm x 3 mm thick, burried directly in ground vertically to a depth not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with copper strip of size 20 x 3mm by means of nuts, bolts, check nuts and washers to be protected by galvanised iron pipe 32mm bore (light grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (medium grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab of size 450 x 450mm (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on complete all as specified and as directed.

DG SET Supply, installation, commissioning and testing of Silent type diesel engine driven generating set 415 volts, 500 KVA, 3 phase, 50 Hz, 0.8 power factor, 1500 RPM, self excited, self regulated, brushless AC Generator in cluding accoustic enclosure suitable for ambient condition at JORHAT and confirming to IS: 10002, 13364 Part-I(1992), BS - 5514/5000 with the following ( The capacity of the generator set shall be net after all due derating factors as per relevant IS/BS standards):- (A) ALTERNATOR:- (i) Stanadard design alternator rated at 500 KVA at 0.8(lag) power factor, AC, 3 phase, 4 wire, 415 volts, 50 Hz, 1500 RPM, self excited, self regulated, screen protected, drip proof brushless design with winding in pole faces, insulating class 'H' and voltage regulation of +1% at rated voltage from no load to full load. The alternator shall be confirming to BS:5000, IS:13364 Part-I(992) and shall be in position to generatesupply with frequency regulation with in +1% tolerance. The alternator will be suitable for tropical climate and shall generally confirm to BS:2613/5000/Is-4722. (ii) Insulation: Class 'H'. (iii) Temperature rise: Class 'H'. (iv)Excitation: Self excited (v) Regulation performance: The voltage is kept constant with +1%. (vi) Frequency regulation: +1%.

SRL ITEM No.18.04 (Contd…\) (B) DIESEL ENGINE: Adequate capacity of diesel engine, water colled to drive independently above alternator and after considering de-rating as per site conditions after generating and reducing power consumed by accessories directly coupled through flexible coupling, multi cylinder, multi stroke, direct injection, cold starting, 1500 RPM as per relevant IS/BS, complete with standard accessories, all as specified and required for safe handling and operation. Salient features of accessories shall be as under:- (i) Fly wheel with housing (ii) Cooling system: Moulded radiator with fan & belts (iii) Cooling water pump: Centrifugal type belt driven. (iv) Exhaust system: Exhaust system complete with exhaust piping of suitable dia with MS pipe(medium grade). Turbo charger type. Exhaust manifold. Solencer: Residential type. (v) Fuel System: Fuel injection system with fuel injectors, fuel njection solenoid switch controlled by governer electric operated (as recommended by OEM) for 1% speed/ frequency regulation. Fuel filters, Fule hoses. (vi) Lub oil system: Lubricating oil filter, Lubricating oil pump. (vii) Air Intake system: Air intake manifold, Air cleaner dry type. (viii) Governer: Mechanical type. (ix) Starting system: Electirc self starter with and including battery charging alternator 24 Volts DC. (x) Batteries: Batteries of maintenance free of capacity 12 V, 150 AH- 02 No, complete, with copper conductor multistranded leads of suitable length from self starter to the battery terminals, complete with initial charge and intial fill of electrolyte, all as specified. (xi) Start and stop push button (xii) Ignition key/switch

SRL ITEM No.18.04 (Contd…\) (xiii) Radiator with blower fan & first fill of coolant oil. (xiv) Corrosion inhibitor coolant. (xv) Direct fuel injection system through governer mechanical type. (xvi) Generator Monitoring panel: Comprising of all standard items as per standard manufacturing, ignition key switch and start/stop arrangement, indications for engine parameters, hour run meter, RPM meter, engine oil presuure indicator, water/coolant temperature indicator, battery volt display. (xvii) Safety controls: Engine low lube oil pressure, high water temperature and over speeding of engine. (xviii) Coupling arrangement: Flexible coupling. (xix) Accessories: AVM pads built-in r separately mounted to manufacturer base frames. (xx) Base frame: Made out of ISMC of sturdy design made of MS channel with necessary reinforcement and predetermined holes as per manufacturer. (xxi) MS/Steel flexible pipeline to and fromthe fule tank to the Dg set. (xxii) Battery charger shall be provided as per manufacturer guidelines. (xxiii) The DG set shall comply to the emission limits requirement as per GOI gazette notification No.595 dt 11 Dec 2013 and No.167 dt 31 Mar 2014. The DG set shall be complied with all test requirements as stipulated in the gazette notification. All relevant test results from NABL accredited lab shall be produced to GE.

SRL ITEM No.18.04 (Contd…\) (C) CIVIL WORKS: All civil works including PCC platform and related foundations including for panel and equipments including making good of disturbed during installation and commissioning of genset. The depth and size of the foundation and PCC as recommended by the manufacturer. (D) ACCOUSTIC ENCLOSURE: (i) Manufactured by OEM suitable for 500 KVA DG set. (ii) Tested by NABL approved lab as per CPCB. (iii) It should be as per latest rules and regulations of Ministry of Environment and pollution control board. (iv) The generating set battery shall be inside the enclosure. (v) Fuel tank shall be inside the enclosure and the fuel storage shall be enough for 12Hrs continuous operation. If required, arragemnt shall be provided outside the enclosure also, to achieve this requirement. (vi) Outer body & doors shall be of CRCA sheet of 1.6mm thick. (vii) sound insulation: 100mm thick rock wool (minimum density 64 Kg/Cum)/ fire resistance foam/puff as per OEM/ as per standard manufacturing to achieve desired decibel level. (viii) The accoustic enclosure shall be composite in construction and fully asembled integral unit. (ix) The DG set should be provided with external emegency stop push button. (x) The enclosure shall be suitably internally illuminated by CFL/FTL lamp fittings. (xi) The noise level should be 75dB at 1m under free field conditions. (xii) The accoustic enclosure parts shall be powder coated after pretreatment process. The base frame shall be painted with epoxy based balck shade.

An amount of Rs. 16,32,146.80 as stipulated in Schedule 'A' Part-XVIII (SCHEDULE OF CREDIT) will be from the total sum quoted by the contractor in this BOQ to arrive at the lumpsum.

NSC Projects Pvt. Ltd.

surendra infrastructure pvt ltd

FRIZO INDIA PVT LTD

D. K. PROJECT PRIVATE LIMITED

Rabina Enterprises Pvt Ltd

B D Raizada Projects Pvt Ltd

SARAOGI BUILDERS LIMITED

Saru Enterprises Pvt Ltd