SPECIAL REPAIRS TO OFFICERs MESS AT FRONT PORTION AT MALAD COMPLEX AT COD AND PROVISION OF NEW SEPTIC TANK FOR LADIES TOILET IN BLDG NO. NP-16 OF AFMSED KANDIVLI UNDER GE NORTH MUMBAI

Amount

Disconnecting of PVC water storage tank of capacity exceeding 500 litres and not exceeding 1000 litres, setting aside (or lowering if required) for repairs, cleaning etc. and hoisting if required reconnecting and refixing in position including provision all necessary fittings etc complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete unreinforced of old water proofing treatment of any description and in any position, not otherwise specifically provided for, any thickness, above ground floor including removal of rubbish outside MD land complete all as specified and as per directed.

Material and labour for roughening surface of old concrete roof/floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed

Material and labour for brushing neat cement slurry with 3.0 kg of cement per sqm all as specified and as per directed

Material and labour for 40mm thick (average thickness) Plain Cement Concrete (1:2:4) type B1, using 20mm graded stone aggregate as levelling course, laid to slope as required, finished even and fair all as specified and as directed by Engineer-in-Charge.

Material and labour for rendering 10mm thick in cement mortar (1:3) on roof slab / canopies / chajjas with water proofing compound @ 3% by weight of cement or as per manufacturer's instruction and make surface receive water proofing Treatment, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge Note : water proofing compound will be measured and paid for separately as supply only

Material and labour for APP modified membrane roof treatment to parapet wall / inaccessible roof surface to the following specification:- (a) Applying oil bound bitumen primer @ 0.40 lit / Sqm of density 0.87 - 0.89 Kg/lit of 25 0 C after preparation of surface. (b) Supply and lay 3mm thick APP membrane weight not less than 3.30 kg per sqm by torch application with minimum 10cm side lap and 15cm end lap. The laying of membrane shall be got done through an authorized applicator of manufacturer of APP membrane. (c) Applying one coat of solar reflective bituminous paint all as per manufacture's instruction complete all as specified and as directed.

Supply only integral water proofing compound ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Pidilite Industries Ltd, Taloja /Super Aquacem (India) Ltd /FOSROC/Siko/Dr Fixit

Demolition of brickwork built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Material and labour for brick work with sub class "B" bricks, straight or curved on plan, exceeding 6 mtr mean radius, with old size bricks and built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-Charge

Material and labour for brick work with sub class "B" bricks, straight or curved on plan, to any radius in half bricks thick walls , built in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge

Material and labour for surface preparation of existing concrete components including griding/rubbing carefully by grinder without damaging the existing concrete including cleaning the surfaces by blower , removal of external plaster wherever exists. Cost inclusive of transportation, labour conveying debris away from the Defence land, tools and tacklers, lead and lift and clean water thoroughly complete all as specified and directed by Engr-in-Charge.

Supply and fix mild steel TMT bars, 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. Note: Cutting of rusted reinforcement & welding shall be inclusive in this item of work

Supply and fix mild steel TMT bars, 5 to 10mm dia in stirrups, spacers and binder cut to length bent to shape required inch cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. Note: Cutting of rusted reinforcement & welding shall be inclusive in this item of work

Demolition of reinforced cement concrete of any description and in any position, not otherwise specifically provided for and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Supply & fix MS/TS dowel pins/staple/shear pins including drilling holes in concrete and providing labour and includes the materials for epoxy grouting the pins etc complete all as specified and as directed by Engineer-in-Charge.

Repairing of excessively damaged concrete portion by using superfluid dual shrinkage compacted and providing, casting with micro concrete of grade M-40 at all levels with all leads and lift as directed including mixing, laying, levelling, finishing including curing etc complete all as specified and directed by Engineer-in-Charge. Make: Fosroc / SIKA / BASF / Krishna Conchem or equivalent approved .

Material and labour for formwork of to pour the micro concrete/concrete using steel shutters or 12mm marine ply to have the form finish including de-shuttering etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for providing and applying rust cleaner (Re-backler solution) to exposed corroded reinforcement @ 0.20 Litre/Sqm or approved make over prepared reinforcement, including removing concrete all around reinforcement including from behind the reinforcing bars by manual methods such as hammering the rebar, using wire brushes, chiselling, etc. and applying rust removing solution of approved make with cotton waste swab to reinforcements etc. complete as directed by Engineer-In-Charge.

Material and labour for providing and applying two coats of anticorrosive epoxy phenolic rebar protective system IPNet RB or equivalent of approved make and quality comprises of resin and hardener mixed in equal proportion by volume with minimum 9-10 hours between the coats, sprinkling dry sand when 2nd coat is tacky so as to provide rough finish and ensuring air curing of minimum 10 hours after the top coat before any subsequent treatment etc. including scaffolding etc complete all as specified and as directed by Engineer-in-Charge. NOTE:- New Reinforcement shall be measured and paid separately under respective item. (b) Cost of welding deemed to be inclusive in this item of work.

Material and labour for providing and applying a priming cum bonding coat of two component Epoxide Resin conforms to ASTM-C-882-91 of approved make and quality to clean and sound concrete area by brush or any other established method by mixing Base and curing agent in 2:1 proportion by weight for joining old and new concrete as per technical specifications of manufacturer. Work shall be carried out as per the manufacturers specifications & certificate on this account shall be taken from consultant and as approved by Engineer-in-charge

Material and labour for providing and laying average 30 mm thick POLYMER MODIFIED MORTER over identified R.C.C. members in One layer in proportion of 1:5:15 by weight of polymer of approved make, cement and filler material of approved make, blended to a required consistency and applying and finishing by floating, curing after initial setting time, including providing and inserting 10 mm mild steel shear key bars (minimum 3 nos per sqm), wherever required, bonding slurry, etc complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GE

Removing loose disturbed & disintegrated concrete surface of RCC beams , columns, chajjas, lintel, ceiling etc and cleaning exposed rusted reinforcement , removing rusted scales by chipping and cleaning by wire brushes and applying anticorrosive epoxy coating as per manufacturer's instructions on prepared surface to receive gunniting including necessary scaffolding and preparing to support the damaged structural members, supplying & tying welded wire mesh 75 mm x 75 mm x 3mm dia, binding with GI wire 22 gauge to reinforcement , applying cement slurry uniformly to exposed surfaces and gunniting using CM 1:3, average thickness of gunniting not less than 40mm and finishing the surfaces with 10mm thick rendering in CM 1:3, trowelled even & smooth finish, without using extra cement & removing debris out side MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour Drilling and fixing Teflon nozzles in RCC members, including drilling holes (drilling 12 mm dia, 40mm deep holes in structural members at the intervals of 600mm c/c in staggered manner or s directed by Engineer-in Charge in RCC structure elements and cleaning the holes (to clean the holes by air blower prior to fixing nozzles) and fixing of nozzles (to insert 12mm dia Teflon nozzles in cleaned holes external end of nozzles (to insert 12mm dia Teflon nozzles in cleaned holes external end of nozzles to be machined to receive outlet of grouting gun and fixing it inside the holes by applying thixotropic epoxy putty to ensure complete sealing and curing the system for minimum 12 hrs) and cutting of nozzles (to cut the nozzle by chisel after completion of grouting without damaging structural elements etc complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GE

Material & labour for Injecting epoxy grout by pressure and using mechanized injector gun with accessories, till nozzles refuses to accept the grout, Including, Mixing of materials( Mixing material components (part a & b) in required quantities as per manufacturer’s instruction by weigh batching) and Grouting ( Filling the grouting gun with monomer. Maintain desired pressure in the gun by air compressor; maintain the pressure at exit (4 to 5 Kg/ Cm2) by monitoring pressure gauge at exit. Grouting the material through prefixed nozzles in the structural elements till its refusal. Sealing the nozzle with epoxy putty after the refusal. Monitoring leakages through other nozzles while grouting and seal them as per the requirement. Repeat the process for all the nozzles. the operation to be within pot life of the material.)and Cleaning of gun and accessories ( the gun and accessories like valves, pipes and other fixtures to be cleaned with thinner after the operation to avoid jamming of the gun.) etc complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GE

Material and labour for Strengthening structural elements with non metallic composite fiber wrapping system comprise of uni-directional carbon fiber sheet (430 GSM) and compatible saturate Profiling, applying compatible primer on prepared substrate, Filling the holes and uneven surface with thixotropic epoxy putty etc. , complete mechanized wetting of fiber sheet, cutting the fabric to required size, mixing of saturant and filling in tub area of the saturation machine, placing the fiber on metallic rods and pass through the rollers of machine and saturate tub ensuring complete wetting (65% fiber volume fraction) of fibers, removing the fiber on rod and placing the new fiber sheet, wrapping the fiber sheet to structural element at desired orientation using tamping roller to avoid any air voids etc., repeating the same procedure for multiple layer with the interval of 8 hrs ,applying second coat of saturate after minimum 12 hrs after first coat, rectify air voids if any and finally rendering with10mm thick in CM 1:6 including finishing even & smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Mode of measurement- Per sq.mt of surface area of carbon fiber sheet without lapping. Make- FOSROC/FIXIT/Krishna Conchem/ Sika

Providing and fixing carbon fiber anchor including drilling hole in the base concrete, fixing the anchor using epoxy 50X55 system, spreading the anchor fibers in star pattern including application of saturate complete all as specified and as directed by Engineer-in-Charge. Note for Item No.12 to 27:- (i) The work under Item No. 12 to 27 shall be carried out by authorised applicator only. (ii) Defect liability for these items shall be 5 years from certified date of completion. (iii) Amount of 5% of these items shall be retained during RAR and FB. This amount shall be released after successful completion of Defects liability period as mentioned above. (iv) Non destructive testing shall be got carried out through IIT / NIT / College of Engineering Pune/Govt approved consultant /NABL approved Lab to decide fulfilment of fitness criteria of the structure. (v) The test shall be carried out at each discrete location or locations decided by GE or testing authority. (vi)The cost of testing shall be deemed to be included in the rate quoted by the contractor. Completion shall be issued by GE after only getting structural stability certificate of each respective building from testing authority.

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and removing debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Material and labour for rendering 10mm thick on internal wall surfaces using factory manufactured pre mix/ready mix plaster of 'Roofit Mix' of M/s Premier Floor to Roof Materials Pvt Ltd/'Easy plast' of M/s Walplast Products Pvt Ltd/ 'Readiplast' of M/s Ultratech Cement Ltd' / Soundplast PMC-1 of M/s Sound buildcare Pvt Ltd/or other approved equivalent make, having minimum composition of C:S : 1:6 using fully treated dry, well graded natural sand confirming to IS 383 suitable for plastering, having low rebound properties, low water demand for curing properties mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over masonry and concrete surfaces and finishing with sagol finish not less than 1mm thick, including dubbing of plaster of any thickness with same ready mixplaster and provide 150mm chcken wire mesh fixed with nails at the junction of RCC columns/walls/beams. Lintels and brick masonry at external faces before plastering including scaffolding at any height cleaning the surfaces, curing etc complete all as specified & directed by Engineer-in-Charge. Note :- The rate is including dubbing of plaster with ready mix of approved make in CM 1:4 of average 20 mm thick complete.

Material and labour for rendering 5 mm thick on ceiling using factory manufactured pre mix/ready mix plaster of 'Roofit Mix' of M/s Premier Floor to Roof Materials Pvt Ltd/'Easy plast' of M/s Walplast Products Pvt td/'Readiplast' of M/s Ultratech Cement Ltd' / Soundplast PMC-1 of M/s Sound buildcare Pvt Ltd/or other approved equivalent make, having minimum composition of C:S : 1:3 using fully treated dry, well graded natural sand confirming to IS 383 suitable for plastering in ceiling, having low rebound properties, low water demand for curing properties mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over concrete surfaces and finishing with sagol finish not less than 1mm thick, including cleaning the surfaces, curing etc complete all as specified & directed by Engineer-in-Charge.

Material and labour for rendering 15 mm thick cement plaster in CM 1:4, two coats using factory manufactured pre mix/ready mix of 'Roofit Mix' of M/s Premier Floor to Roof Materials pvt.ltd/ 'Easy plast' of M/s Walplast Products pvt.ltd/ 'Readiplast' of M/s Ultratech Cement Ltd/'Soundplast PMC-1' of M/s Sound buildcare pvt.Ltd/ or other approved equivalent make, having minimum composition of C:S :1:4 using fully treated dry, well graded natural sand conforming to IS 383 suitable for external plastering, having low rebound properties, low water demand for curing properties, mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over exterior masonry and concrete surfaces with base coat of 10 mm thick and finishing coat of 5 mm thick final rendering with water proofing compound as per manufacturer's instructions, including using richer mix for making corners if necessary, at all floors and level, including making grooves of existing size wherever required, including cleaning the surfaces, curing including provide of 150mm chicken wire mesh fixed with nails at the junction of RCC columns/walls/ beams/ lintels and brick masonry at external faces before plastering including scaffolding at any height and all safety materials required for execute work etc complete all as specified and as directed by Engineer-in-Charge. Note :- The rate is including dubbing of plaster with ready mix of approved make in CM 1:4 of average 20 mm thick complete.

Material and labour for opening out cracks in wall surfaces in 'V' shape by mechanical grinder and removing the loose material. filling with crack filler of Dr. Fixit crack-X, shrinks free or equivalent all as per manufacturer's instructions and finishing the surfaces to match with existing finish complete all as specified and as directed

Material and labour for preparation of new plastered surfaces of ceiling and applying two coats of Distemper oil emulsion over a coat of priming plastered and other surfaces with alkali resistant priming paint over thin layer of wall care putty complete all as specified and as directed Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for preparation of new plastered surfaces of wall and applying two coats of plastic emulsion paint over a coat of priming paints over thin layer of wall care putty complete all as specified and as directed Make- Asian paints/ Nerolac paints/Berger paints/ Shalimar paints/ Dulux

Material and labour for preparation of new plastered surfaces of ceiling and applying two coats of Distemper oil emulsion over a coat of priming plastered and other surfaces with alkali resistant priming paint over thin layer of wall care putty on ceiling complete all as specified and as directed Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for preparation of newly plastered wall surfaces and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparing new plastered surfaces and applying two coats of Acrylic weather proof coat over one coat of acrylic primer on wall surfaces complete all as specified and as directed by Engineer-in-Charge Make- 1“APEX ULTIMA” of Asian Paints 2 “WEATHER COAT ALL GUARD” of Berger Paints 3 “EXCEL TOP GUARD” of Nerolac 4 “DULUX WEATHERSHIELD MAX” of ICI India

Material and labour for complete removal of existing treatment of paint of wall and applying two coats of Distemper oil emulsion over a coat of priming plastered and other surfaces with alkali resistant priming paint over thin layer of wall care putty complete all as specified and as directed Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for preparation of old painted surfaces of wall and applying two coats of plastic emulsion paint over a coat of priming paints over thin layer of wall care putty on wall complete all as specified and as directed Make- Asian paints/ Nerolac paints/Berger paints/ Shalimar paints/ Dulux

Material and labour for preparing new plastered surfaces and applying two coats of Acrylic weather proof coat over one coat of acrylic primer on wall surfaces complete all as specified and as directed by Engineer-in-Charge Make- 1“APEX ULTIMA” of Asian Paints 2 “WEATHER COAT ALL GUARD” of Berger Paints 3 “EXCEL TOP GUARD” of Nerolac 4 “DULUX WEATHERSHIELD MAX” of ICI India

Material and labour for preparing old wooden surfaces of any description, over 10 cm width or girth, and applying one coat of synthetic enamel paint complete all as specified and as directed Make : Asian paints/ Nerolac paints/Berger paints/ Shalimer paints/ Dulux

Material and labour for preparing old wooden surfaces of any description, over 10 cm width or girth, and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed Make : Asian paints/ Nerolac paints/Berger paints/ Shalimer paints/ Dulux

Material and labour for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed Make : Asian paints/ Nerolac paints/Berger paints/ Shalimer paints/ Dulux

Taking down chowkats or frame with shutters, not exceeding 1.5 sqm each (without taking off shutters from the frames) & removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed

Taking down chowkats or frame with shutters, exceeding 1.5 sqm but not exceeding 4.00 sqm each (without taking off shutters from the frames) & removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing on Serial Page No 151 of SSR Part II (pertaining to item No 08095) and edges to be painted to match with prelam sheet complete all as specified and as directed by Engr-in-Charge. Make : RAJSHRI / SINTEX / TUFFFLON / M/s Navratan Specialty Chemical LLP – ‘Brand : GIZA’

Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of M. S. tubes for top & bottom rails. M.S. frame shall be covered with heat molded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at site as per specification & drawing on Serial Page No 149 of SSR Part II (pertaining to item No 08080) including necessary aluminium builders hardware for one door to be provided such as 100mm dia butt hinges - 3Nos, tower bolt 200mm dia - 2Nos, handle 200mm long - 2 Nos etc complete all as specified and as directed by Engineer-in-Charge. Make : RAJSHRI / SINTEX / TUFFFLON / M/s Navratan Specialty Chemical LLP – ‘Brand : GIZA’

Supply and fix floor door stopper of stainless steel 150mm complete all as specified and as directed. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix extruded aluminium alloy handles fabricated types, anodised, of size 150 mm complete all as specified and as directed Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminium anodised barrel tower bolt of extruded section size 150mm complete all as specified and as directed. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminum anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy 250mm long complete all as specified and as directed. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring 140mm size complete all as specified and as directed. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix coloured aluminium sections for sliding or openable windows, ventilators, doors, partitions etc including fabrication of frame & shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc including all accessories such as glazing clips and rubber beadings for fixing glass panes / wire mesh in frame complete all as specified Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/ Ajit India Note: (i) Glass panes /wire mesh will be measured & paid separately. (ii) Rubber beading will not be weighed.

Supply and fix Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with staple complete all as specified and as directed

Supply and fix aluminium anodised grill square/rectangular, fixed with aluminium channel of size 38mm X 12mm X 1.3mm, "DECO GRILL OF DG-101 complete all as specified and as directed. Make: DECOGRILLE of Associated group / Royal Alum grill Pvt Ltd or equivalent make as approved by GE

Supply and fix Aluminium alloy wire mesh 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples

Taking down aluminium window shutter carefully from aluminium sliding frame, n.exc 2 sqm each and refixing in same position after replacing the window glass pane, wire mesh and nylon roller, rubber beading etc complete all as specified and as directed by Engineer-in-Charge. Note: Glass pane and wire mesh will be measured and paid separately under respective item

Taking down aluminium window shutter carefully & refixing in same position after repair/replacement of handle, floor door stopper , glass and rubber etc,. area exc. 1 sqm but not exc. 2sqm each complete all as directed by Engineer-in-Charge. Note: Glass will be measured and paid separately

Taking down chowkats or frame with shutters, not exceeding 1.5 sqm with shutters(without taking off shutters from the frames) & refixing in same opening complete all as directed by Engineer-in-Charge.

Taking down chowkats or frame with shutters, exceeding 1.5 sqm but n. exc. 4sqm with shutters(without taking off shutters from the frames) & refixing in same opening complete all as directed by Engineer-in-Charge.

Supply and fix in repairs stainless steel curtain rod , 25mm dia c complete all as directed by Engineer-in-Charge.

Supply and fix in repair Fancy type brass chromium plated brackets for curtain rod 25mm dia fixed to wall complete all as directed by Engineer-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing the rubbish out side MD land complete all as specified and as directed

Demolition of cement concrete {unreinforced} in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) removing the rubbish out side MD land complete all as specified and as directed

Material and labour for 75mm cement concrete (1:4:8) type D2 using 40mm graded stone aggregate as in sub base of footing/hard standing path and finishing the surface even and smooth without using extra cement as specified and as directed

Material and labour for 75mm cement concrete (1:3:6) type C1 using 20mm graded stone aggregate as in plinth protection and finishing the surface even and smooth without using extra cement, joints in plinth protection shall be filled with bitumen mastic (1:3) as specified and as directed

Material and labour for light shade, vitrified tiles, 10mm thick (minimum), (square/ rectangular) polished, area of each tiles not exc exceeding 0.36 Sqm (including 600mmx600mm size), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6 complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles

Material and labour for light shade, vitrified tiles, 10mm thick (minimum), (square/ rectangular) polished, area of each tiles not exc exceeding 0.36 Sqm (including 600mmx600mm size), on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including 10 mm thick backing coat in cement mortar 1:3 complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/ rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6 complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/ rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6 complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles

Material and labour for coloured glazed ceramic tiles of size 350mm x 250mm x 7 mm thick/ 450mm x 350mm x 7mm , on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid dry or laid dry and pointed complete all as specified and as directed by Engineer-in-Charge.

Material and labour marble work 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillar, window cills, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2), using marble dust with admixture of pigment to match with marble shade of makrana white over 10mm thick backing coat in cement mortar (1:4) complete all as specified and as directed

Material and labour for granite (any colour granite) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry as in skirting/dado and pointed with white cement with admixture of pigment to match the shade of granite tiles including grinding and polishing including 15mm thick backing coat in cement mortar (1:6) complete all as specified and as directed.

Material and labour for machine pressed precast concrete interlocking paver block lacquer finish of any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment including 25mm thick crushed stone sand cushioning including watering and consolidation below paver block cushioning complete all as specified and as directed by Engineer-in-Charge. Make: Mehtab Tiles/Indore/M/S Ultra Tiles/NITCO/Topaz Tiles/Navya Tiles Jodhpur

Material and labour for factory made Precast, cement concrete (1:2:4) type B-1, using 20mm graded stone aggregate in kerb stone of size 300mm x 400 x 100mm in required shape finished smooth, set in cement mortar 1:4 including excavation earth work in any type of soil complete all as specified and as directed

Taking up or down 15mm bore steel tubing and connections& removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed

Taking up or down 20mm bore steel tubing and connections & removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed

Taking up or down 25mm bore steel tubing and connections & removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed

Supply and fix 40mm outer dia, three layer PP-R polypropylene random copolymer concealed pipes SDR- 7.4 (PN-16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceiling or in floors complete all as specified and directed by Engineer-in-Charge. Make : Prince/Finolex/Supreme

All as per item No 84 described here-in-before but 32mm dia complete all as specified and directed by Engineer-in-Charge.

All as per item No 84 described here-in-before but 25mm dia complete all as specified and directed by Engineer-in-Charge.

All as per item No 84 described here-in-before but 20mm dia complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs bib taps, fancy type, chromium plated, cast copper alloy, long body with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed. Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix in repairs concealed type stop valve, cast copper alloy, fancy type screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed. Make : Jaquar (Essco)/Prayag / Seiko

Material and labour for Rolled mild steel sections as in joist, channel, angle, or tee sections, without connecting plates, etc to form frame complete all as specified and conforming to Fe - 410 W (Grade E-250) 'B' quality complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of colour having tensile self tapping screws as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge. Make: JINDAL / INDALCO / HINDALCO / ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets

Preparing new steel surfaces of any description, exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge. Make : Asian paints/ Nerolac paints / Berger paints / Shalimar paints / Dulux

Dismantling Wall lining boards, of any type & any thickness, including cover fillets and removal of rubbish outside of MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour in repair for anodised aluminium snap grid frame work for false ceiling conforming to designation 3600 in IS-207-10985 including all ceiling cleats, 4 mm dia GI wire suspender with necessary main tee 35.00 x 23.50 x 1.50mm , cross tee and wall angle of size 23.50 x 23.50 x 1.5 mm with 605 x 605 mm grid system complete all as specified and as directed by Engineer-in-Charge.

M & L for Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having Philips head with under head cutter at 200 mm centre to centre, including finishing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish complete all as specified and as directed by Engineer-in-Charge. (Frame work for ceiling shall be measured and paid separately) Make- 1 Anchor Ceiling Tiles 2 Armstrong 3 Anutone 4 Bison Panel 5 Lagyp 6 Gypboard

Providing and fixing 10mm thick plaster of Paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh complete all as specified and as directed by Engineer-in-Charge.(Fillets, metal frame work and G.I. wire mesh paid separately)

Material & labour for plaster of Paris cornices of any size & shape or as desired /recommendation etc complete all as specified and as directed by Engineer-in-Charge.

Excavation over areas n. exc 1.5 m in deep and getting out in hard/dense soil complete all as specified and as directed

Excavation over areas exc 1.5 m but n exc 3m deep and getting out in hard/dense soil for exposing of pipe etc complete all as specified and as directed

Material and labour Plain cement concrete 1:4:8 type D-2 Nominal mix (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed

Material and labour Plain cement concrete 1:2:4 type B-2 Nominal mix (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed

Material and labour for brick work with sub class "B" bricks, straight or curved on plan, exceeding 6 mtr mean radius, with old size bricks and built in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge

Material and labour for reinforced cement concrete with nominal mix, 1:2:4, type B1 using 20mm graded stone aggregate as in walls complete all as directed

Material and labour for 15mm thick rendering in two coats (10mm + 5mm) with cement mortar 1:4 of any thickness on fair faces of brick or concrete surfaces, finished even and fair mixed with water proofing compound @ 2% by weight of cement in CM 1:4 etc complete all as specified and as directed by Engineer-in-Charge. Note: WPC will be measured and paid separately.

Material and labour for reinforced cement concrete with nominal mix, 1:2:4 , type B1 using 20mm graded stone aggregate as in landings, slabs supported on wall, roofs and similar articles complete all as specified and as directed by Engineer-in-Charge

Material and labour for precast reinforced cement concrete with nominal mix, 1:2:4, type B1 using 20mm graded stone aggregate as in landings, cover slabs, chajjas etc. and similar articles with plain faces set in CM 1:6 complete all as specified and as directed by Engineer-in-Charge

Material and labour for plain cement concrete with nominal mix, 1:2:4 , type B1 using 20mm graded stone aggregate as in bands, coping etc complete all as specified and as directed by Engineer-in-Charge

Supply and fix mild steel TMT bars, 8mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pilasters, buttresses, etc.; vertical or to batter for fair finished surfaces complete all as specified and as directed by Engr-in-Charge.

Material and labour for Formwork to soffits of suspended slabs such as floor slabs, roof slabs, landings, chajjas and similar work not exceeding 200mm thick for rough finished flat surfaces of concrete complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete for rough finished flat surfaces of concrete complete all as specified and as directed by Engineer-in-Charge.

Supply and fix PVC (SWR) 110mm pipes, type B, single socketed, in length with rubber ring joints laid in trenches in floors complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Finolex / Supreme

Supply and fix cast iron soil, waste and vent pipes (ISI Marked) in any length with or without ears, with cement joints, fixed to walls including cutting of holes wherever required etc complete all as specified and as directed by Engineer-in-Charge. Make- 1 Electro-Steel 2 Kejriwal 3 NECO 4 Kesoram

Supply and fix PVC (SWR) junction single 110mm bore (Single T) equal or unequal complete all as specified and as directed. Make : Prince / Finolex / Supreme

Supply and fix CI cowl 100 mm dia, ISI marked complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Round bars 16 mm dia and over cut to length bent to shape required including binding with mild steel wire (annealed) not less than 0.9 mm dia all as specified and directed

Removing excavated material to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5 mtr above the starting point all as specified and as directed by Engineer-in-Charge.

Material and labour reinforced concrete pipes 150mm bore, class NP-2, laid and jointed in CM (1:2) with spun yarn complete with collars all as specified and as directed by Engineer-in-Charge. Make : Indian hume pipes/Everest/Himalaya/Thuluvananikal Pipes

Material & labour for loose filling with aggregates of broken bricks of gauge 80 to 150 mm in soakage pits, soakage wells complete all as specified and as directed by Engineer-in-Charge.

Material and labour for hardcore of broken stones of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface all as specified and as directed.

Returning filling in, including spreading, levelling, watering and well ramming of hard dense soil in layers not exc 25cm complete all as specified and all as directed by Engr-in-Charge.

M&L for cement concrete 1:4:8 type C2 (using 40mm graded stone aggregate), as bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in, bore of pipe 150mm bore of pipe complete all as specifed and directed

Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc., removing materials out side MD land in case of Credit and making good disturbed surfaces of walls, floors, etc., all as specified and as directed.

Material and labour for point wiring with proper colour coding complete with and including PVC insulated unsheathed, flexible bright annealed multi stranded copper conductor single core FRLS cable 1.5 Sqmm (22/0.30) 1100 volt grade confirming to IS 694 drawn through in and including (medium grade) rigid non metallic PVC conduit pipe 25 mm size ISI marked with conduit accessories / fittings / junction box / inspection covers etc of ISI marked and cutting chases for concealed conduit with all surfaces by means of screws and sunk / cup washers, for mounting of switches sockets fan regulators etc including 1.5 sqmm (22/0.30) 1100 volts grade PVC insulated FRLS unsheathed flexible, multi stranded copper conductor cable (green colour) as continuous earthwire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end all as specified and as directed for one light/ bell/ fan point Note : (a) Cutting chases & making good disturbed surfaces will be measured and paid separately. (b) Modular sunken boxes with cover plate will be measured & paid separately

All as per item No.124 here-in before but for one 5 pin socket point 6 Amps on independent board

All as per item No.124 here-in before but for one 5 pin socket point 6 Amps on same board controlled by another switch

All as per Item No.124 here-in-before but for one socket point on independent board, 15 Amp socket with 2.5 sqmm PVC unsheathed FRLS wire complete all as specified & as directed by Engineer-in-charge.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sun shades, shelves, lintels, etc and cutting chases for concealed conduit wiring, etc and making good, cutting not exc 10 cm girth complete all as specified & as directed by Engineer-in-charge.

Supply and fix, LED wall light decorative fixture, 1x27 watts, 220 volt, AC, die cast aluminium housing with glass diffuser including lamp with IP 43, connecting up with 3 core flexible copper conductor cable of suitable size from ceiling rose including 2 Nos of PVC square/round boxes, screws, clips etc complete all as specified and directed by Engineer-in-Charge-in-Charge, Make : Jaguar, Model- Firenze, Cat No. 330.00.NGG or equivalent in WIPRO / Phillips

Supply and fix, batten type LED tube light fitting, 1x20 watts, 220 volt, 4 feet with long lasting all pre-wired fixed on walls with all fixing accessories such as 2 Nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20sqmm complete all as specified and directed by Engineer-in-Charge-in-Charge, Make : Havells Cat Part No LHEXACP7UN1W020 or equivalent in Bajaj / CG / Phillips

Supply and fix LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size including taking down existing light fittings etc complete all as specified and as directed by Engineer-in-Charge. Make : Phillips Cat No RC380B LED36S -6500 G4 L60 W60 PSU OD or equivalent of Havells / Crompton Greaves.

Supply and fix in repairs Modular type switch, single pole, one way, 6 Amps, One Module, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / L&T / Honeywell/Crabtree/leader

Supply and fix in repairs Modular type switch, single pole, one way, 16 Amps, One Module, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / L&T / Honeywell/Crabtree/leader

Supply and fix in repairs Modular type bell push one module for call bell single pole one way 6 Amps, 240 volt, 50Hz all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / L&T / Honeywell/Crabtree/leader

Supply and fix Electric bell/ding dong AC 230 V single pole ding dong type complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / L&T / Honeywell/Crabtree/leader

Supply and fix ceiling rose, 3 phase/ PVC/Polycarbonate, insulated body, three terminals complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / L&T /Leader

Supply and fix Modular type socket outlet combination 2 in 1, 3 Pin, 6 Amps, flush type, universal ISI marked, 2 module complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / L&T / Honeywell/Crabtree/leader

Supply and fix in repairs Modular metal flush box 2 module including white cover plate with frame etc complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / L&T

Supply and fix in repairs Modular metal flush box 3 module including white cover plate with frame etc complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / L&T

Supply and fix in repairs Modular metal flush box 4 module including white cover plate with frame etc complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / L&T

Supply and fix in repairs Modular metal flush box 6 module including white cover plate with frame etc complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / L&T

Supply and fix Modular type socket outlet combination 2 in 1, 3 Pin, 16 Amps, flush type, universal, ISI marked, 2 module complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / L&T

Supply and fix in repairs double door, sheet metal enclosure, powder coated for MCB DB SPN 8 way fitted with neutral link, earth bar, din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engineer-in-Charge. Make:-Havells/ Schneider/Legrand/L&T

Supply and fix in repairs MCB SPN, 5 Amps to 32 Amps, 240 volts,10 KA complete with connection, testing & commissioning all as specified and as directed by Engineer-in-Charge. Make : Legrand / L&T / Havells / ABB / Siemens / Schneider

Supply and fix in repairs MCB SP, 5 Amps to 32 Amps, 240 volts,10 KA complete with connection, testing & commissioning all as specified and as directed by Engineer-in-Charge. Make : Legrand / L&T / Havells / ABB / Siemens / Schneider

Material and labour for submain wiring complete with and including 2 runs of 6.0sqmm, single core FRLS, PVC insulated and unsheathed, multistranded, copper conductor cable, single core, 1100 Volts grade drawn through and including PVC conduit, medium grade of size 25mm dia including accessories such as Tees, Elbows, junction box, reducers etc as required and fixed on walls/concealed and 6.0sqmm PVC multistranded copper conductor cable for earthing and connected to common earth dolly including taking down the existing submain wiring complete all as specified and as directed by Engineer-in-Charge. Note : Two runs of 6.0sqmm PVC insulated cable and one run of 6.0sqmm cable and one run of PVC conduit shall be measured as one unit length.

Supply and fix in repairs Modular type fan regulator rotary step deluxe, 240 volt, 50Hz all as specified and as directed by Engineer-in-Charge. Make: Anchor / Leader / L&T / Legrand

Note: Deduct Credit for demolished / dismantled material of Rs. (-) 22,410.50 (Minus) as listed in Schedule of Credit. Tenderers will not quote against this item being a tentative amount to be considered to arrive at the 'Contract Sum'

SHANTI CONSTRUCTION

DAKSH ENGINEERS AND BUILDERS