Redevelopment and Beautification of Shalimar Canal including Placemaking and Improvement of Access etc. to Shalimar Garden.

Amount

Civil Works:

Demolishing cement concrete manually/by mechanical means including Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge: 1:4:8 or leaner mix (i/c equivalent design mix)

Dismantling of flexible pavement (bituminous courses) by mechanical means and disposal of dismantled material upto a lead of 1 kilometer, as per direction of Engineer-in-charge.

Taking out existing kerb stones of all types from footpath/ central verge,including removal of mortar etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 meter lead as per direction of Engineer-in-Charge.

Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 meter lead as per direction of Engineer-in-Charge.

Demolishing stone rubble masonry manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: In cement mortar

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads & lifts

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:

Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil :

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth,consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Disposal of Lime, moorum, building rubbish upto 10 km Lead

Coursed rubble masonry with hard stone (first or second sort) in superstructure above plinth level and upto floor five level including curing complete with: Cement mortar 1:6 (1 Cement : 6 coarse Sand)

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC,carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Construction of dry lean cement concrete sub base over a prepared subgrade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in-charge.

Providing and applying tack coat using hot straight run bitumen of grade – VG-10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications.

Providing and laying seal coat of premixed fine aggregate (passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG-10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface including rolling and finishing with road all complete

Providing and laying bituminous macadam using crushed stone aggregates of specified grading premixed with bituminous binder, transported to site by tippers, laid over a previously prepared surface with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specifications and directions of Engineer-in-Charge. 50 to 100 mm average compacted thickness with bitumen of grade VG-10 @ 3.5% (percentage by weight of total mix) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.

Providing and laying semi- dense Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge. 25 mm compacted thickness with bitumen of grade VG- 10 @5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.

Providing and applying 2.5mm thick road marking strips (retro-reflective) of specified shade/colour using hot thermoplastic material by fully/semiautomatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge

Flooring with Cobble stone of approx. Size 125x125x75 mm (thick) laid on 25 mm average thick cement mortar 1:3 ( 1 cement : 3 Coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the stone, laid in approved pattern complete in all respect as per direction of Engineer-in-charge.

Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, cleaning and curing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) Dark shade using ordinary cement.

Providing, laying and making kerb channel 30cm wide and 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth etc. complete as per direction of Engineer-incharge.

Providing and laying in position specified grade of cement concrete excluding the cost of centering and , shuttering , All work up to plinth level 1:2:4 (1cement: 2 coarse sand : 4 graded stone aggregate (20mm nominal size)

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement: 3 coarse sand) including making joints with or without grooves (thickness of the joints except at sharp curve shall not to be more than 5mm) including making drainage opening wherever required complete etc. as per direction of Engineer-incharge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Mild steel and medium tensile steel bars

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more

Providing and laying in position specified grade of cement concrete excluding the cost of centering and , shuttering , All work up to plinth level 1:1.5:3 (1cement: 1.5 coarse sand : 3 graded stone aggregate (20mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form work for Retaining walls, return walls, walls (any thickness) including attached pilasters buttresses, plinth and string course fillets, kerbs and steps etc.

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm

Providing and laying chisel dressed Devri Stone of size 300x200 mm face with 150 mm depth in cement mortar 1: 6 (1 cement : 6 coarse sand) upto plinth level including curing.One face dressed

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. With 15 mm dia. nominal bore and fixing brass bib cock of approved quality.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Hot finished welded type tubes

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing reinforced by organic fibres and/or inorganic synthetic fibres cement 6 mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymer coated J, or L hooks, bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete (excluding the cost of purlins, rafters and trusses), including cutting sheets to size and shape wherever required.

Supplying and stacking of good earth at site including royalty (earth measured in stacks will be reduced by 20% for payment)

Rough dressing of the trenched ground including breaking clods.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 part of stacked volume of earth after reduction by 20% :1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish & surplus earth, if any with all leads & lifts (cost of sludge, manure or extra good earth, if needed, to be paid for separately) Holes 90 cm dia& 90 cm deep

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 part of stacked volume of earth after reduction by 20% :1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish & surplus earth, if any with all leads & lifts (cost of sludge, manure or extra good earth, if needed, to be paid for separately) Holes 60 cm dia& 60 cm deep

Providing and Displaying Acalypha Different colour well developed, fresh & healthy with good foliage, multi branch 30 to 45 cm ht. in 20 cm size of Earthen Pot/ Plastic Pot bushy as per direction of the officer-in-charge.

Providing and stacking of Jacaranda mimosifolia of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and fixing M.S. flat iron tree guard 60 cm dia. and 2 m high above ground level formed of 4 nos. 25x6 mm, 2.25m long and 8 nos. 25x3 mm 2 m long vertical M.S. flats riveted to 3 nos.25x6 mm MS flat iron rings in two halves, fixed together at site with required 6 no. of 8 mm dia. and 30 mm long bolts including painting two coats with paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD/PWD/any other approved name The tree guard shall be suitably fixed to the ground by embedding four legs of the tree guard in pits of suitable dia. and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction on direction of Officer-in-charge

Manufacturing supplying and fixing retro reflective sign boards made up of 2mm thick aluminum sheet, face to be fully covered with high intensity ncapsulated type heat activated retro reflective sheeting conforming to type-IV of ASTM-D-4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC : 67-2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminum alloy rivets @ 20cm c/c to back support frame ofM.S. angle iron of size 25x25x3mm along with theft resistant measures mounted and fixed with 2 nos. M.S. angles of size 35x35x5mm to a vertical post made upto M.S. Tee section ISMT 50x50x6mm welded with base plate of size 100x100x5mm at the bottom end and including making holes in pipes, angle flats, providing and fixing M.S. message plate of required size steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical M.S.-Tee support to be painted in black and white colours). Backside of aluminum sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coats including all leads and lifts etc. complete as per drawing, specification and direction of Engineer-in-charge. Mandatory/Regulatory sign boards of 900 mm diameter with part as length of 3750 mm

Manufacturing supplying and fixing retro reflective sign boards made up of 2mm thick aluminum sheet, face to be fully covered with high intensity ncapsulated type heat activated retro reflective sheeting conforming to type-IV of ASTM-D-4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC : 67-2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminum alloy rivets @ 20cm c/c to back support frame ofM.S. angle iron of size 25x25x3mm along with theft resistant measures mounted and fixed with 2 nos. M.S. angles of size 35x35x5mm to a vertical post made upto M.S. Tee section ISMT 50x50x6mm welded with base plate of size 100x100x5mm at the bottom end and including making holes in pipes, angle flats, providing and fixing M.S. message plate of required size steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical M.S.-Tee support to be painted in black and white colours). Backside of aluminum sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coats including all leads and lifts etc. complete as per drawing, specification and direction of Engineer-in-charge Cautionary/warning sign boards of equilateral triangular shape having each side of 900 mm support length of 3650mm.

Manufacturing supplying and fixing retro reflective overhead signage boards made up of 2mm thick aluminum sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type-III of ASTM-D-4956-01 as approved by Engineer-in-charge; letters, borders etc. as per IRC : 67-2001 in silver white with blue colour background and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class -II of ASTM-D-4956- 01 and fixing the same to the plate of structural frame work by means of suitable sized aluminum alloys, rivets or bolts and nuts @ 300mm c/c all along the periphery as well as in two vertical rows along with thef resistant measures including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminum sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawing, specification and direction of Engineer-in-charge (Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment).

Providing and fixing Glow studs of size 100x20mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite) or HIP (High impact Polystyrene) or ABS having electronically welded micro-prismatic lens with abrasion resistant coating as approved by Engineer-in-charge. The Glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro-reflective surface shall be 35 +/- 5 degrees to base. The reflective panels on both sides with at least 12cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS : 873 part 4 : 1973. The studs shall be fixed to the road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge.

Supplying and installation of (Roadway Indicators,Hazardmar kers,Objectmarkers) 8 Roads Yellow Traffic Hazard Markers, For Road Safety, Size: 900mm X 300mm.

Pre-casting & Placing in position 125 mm dia Bollards 600 mm high of required shape including providing M.S. Pipe Sleeve 50 mm dia 300 mm long in the Bollard and M.S. pipe 40mm dia and 450mm long with 150x150x6 mm M.S. plate welded at bottom and embeded 150 mm in cement concrete 1: 3: 6 (1 cement:3 coarse sand:6 graded stone aggregate 20 mm nominal size) including necessary excavation of size 250x250x450mm deep for the same in bitumen/concrete pavement at specified spacing.

Providing and fixing post delineators made of ABS round body fitted with 2nos. 100mm dia high reflective and reflectors and mounted on M.S. pipe of 65mm dia duly powder coated with anti-rust and anti-theft steel to be installed as per direction of Engineer-in-charge.

Supplying and installation Solar Traffic Blinker on Pedestrain crossing.

Supplying and installation of mild steel chain link for Bollard Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete as directed by enigineer incharge

CELESTIAL BINS 40 Lts.Stainless SteelWaste Containers or Rigid liners as per Specificationb. Made From High Quality Stainless Steel, including fixing at site as per the direction of manufacturer and engineer in charge.@ 100 mts

Providing and fixing Grating (C.I.) 180x180 mm

Providing and supplying and Instalation of Seating benches at waiting area as directed by engineer incharge.

Providing and laying in position stone soling on all level as per drawing or as directed by Engineer in charge.

Providing and laying in position specified grade of cement concrete excluding the cost of centering and , shuttering , All work up to plinth level 1:4:8 (1cement: 4 coarse sand : 8 graded stone aggregate (20mm nominal size)

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Riveted and bolted

Providing and fixing bolts including nuts and washers complete.

Providing and fixing plain panelling with skirting chair rails, and cornice with necessary screws, priming coat on unexposed surface etc., complete.

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required

Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling necessary holes for rawl plug etc, including priming coat complete: Second class kail road

Stencil Wall Paintings with acrylic emulsion paint of approved brand and manufacture to give an even shade, using spray & stencils of approved clour combination. Two or more coats on newsteel work complete job.

Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications: Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacture

Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications: Painting steel work with deluxe multi surface paint of required shade to give an even shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.80litre/10sqm of approved brand and manufacture

Providing and fixing plained eaves boarding. 2nd class kail wood 250x32 mm (nominal size )

Providing and fixing M.S tubular frames for doors, windows, ventilators and cupboard with rectangular /L-type sections, made of 1.60 mm thick M.S Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with carbon steel galvanized dash fastener of required dia and size (to be paid for separately).

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side / top/ center hung, with beading and all members such as F7D, F4B, K11B and K12B etc. complete of standard rolled steel sections, joints miterd and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings complete all as per approved design , ( sectional weight of only steel members shall be measured for payments. Fixing with carbon steel galvanized dash fastener of required dia and size ( to be paid for separately).

Providing and fixing Polystyrene Foam Board with specified thickness and density @ 35kg/cum , 25-50mm thick sheets , placed as insulation and held in position complete Job including all carriages Thickness of insulation to be filled is 225 mm ( Rate is at LM)

Point wiring for light concealed type in min 20 mm ISI marked HMS PVC conduit with 1.5 sq.mm. (2+1E) FR grade copper wires, modular type switch and required accessories including cost of 12W LED bulb etc complete Job

Point wiring for heating concealed type in min 20 mm ISI marked HMS PVC conduit with 2.5 sq.mm. (2+1E) FR grade copper wires, modular type switch 16A and required accessories inclusive MCB & all carriages etc complete job.

10 sqmm (2-C) unaramed PVC cable fopr service mains and required accessories inclusive all carriages etc complete job.

Wooden planking, tongued and grooved in flooring including fixing with iron screws complete: Second class deodar wood

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. E.R.W. tubes

Electrical Works

Street Light Fitting

Supplying installation and testing of LED FIXTURE - LIGHT 851, Wattage 35-45 W Power Module LED, 3000K, Suspended Light 851:it's upper square frame in single piece made of die cast aluminum using pressure die-casting process,with a decorative element with threaded tube male G 3/4" which is also made of die cast aluminum using pressure die-casting process, fixed on the top. Auxiliary and optical compartment can be accessed by tilting the top frame.Bottom frame with Company /brand name engraved in the mold, in single piece, made of die cast aluminum using pressure die-casting process with a two-armed bracket & decorative element, which is also made of die cast aluminum using pressure die-casting process. Frosted Screen made of polymethylmethacrylate (PMMA) molded in a single piece using Injection molding process. Screen's Impact resistance: IK06. Pure polyester powder coating in Standard Grey Colour. Optical Compartment IP Rating - IP 66. Height – 650mm, Length - 325mm, Width - 325mm,Weight - 6Kg, Area Exposed to Wind(S) - 0.16 m2 Power LED Module with Company /brand name printed on PCB with the metal core plate, in compliance with IEC 62031 (Supporting Test Report from UL Authorised Laboratory should be submitted).LED Chips of CREE/NICHIA/OSRAM/LUMILEDS make shall be used . Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection a minimum of 4 kV (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PC/PMMA .LED Lifetime @L90 >1,00,000hours@Ts 85°C. LM 80 report & TM 21 calculation should be submitted to support the same.The Light fixture shall be in compliance with IEC 60598-2-3; IEC 60598-1(Supporting Test Report from UL Authorised Laboratory should be submitted) .LM79 report also should be submitted from UL Authorised Laboratory. Sample should be submitted for approval from concerned engineer-in charge.

Street Light Pole

Supplying installation and testing of ARCHITECTURAL TWIN ARM SUSPENDED POLE 4 M height Pole made of complete cast iron decorative components where the internal fabricated pole of 3.5M is Made in combination of hot dip galvanised mild steel pipe sections 114 mm dia.,48 mm dia.& covered in the outside by decorative cast iron base and columns. & Top part made in combination of mild steel pipe section 89 mm dia.(vertical) & Decorative cast iron Brackets(2 nos.) with decorated leafs with a 3/4" GAS threaded tube with nut and rose in stainless steel for attaching the light fixture and an internal tube for the passage of a power cable made of cast iron in single piece, to get an arm length of 550 mm & pleasing aethetics as approved. Decorative Cast iron Base design with the company/brand logo engraved in the cast iron mould, starting with dia 260 mm for 130 mm height, followed by a ring of 260 dia gradually tapering to a flat round surface of dia 170 mm for 366 mm height again followed by a ring dia 210 mm and gradual tapering upto a dia 92 mm as approved by the econerned Engineer the total height of decorative cast iron base is 700 mm and weight-32 kgs. Decorative cast iron base should be provided with a flush door of length 228 mm, width 124 mm and height 30 mm. Decorative cast iron flower starting with a dia 102 mm increasing gradually to 160 mm and then tapering to a dia 99 mm.Total height of cast iron flower is 304 mm & weight is 6.3 kgs.. Decorative cast iron column(3 nos.) is of 80 mm dia. and having continuous grooves along the height. The height of each pillar is 750 mm & weight of each pillar is 9.5 kgs. Decorative Cast iron top starting with dia 80 mm and a ring of dia 96 mm at height of 160 mm then gradually increasing to dia 120 mm the top half of the decorative top should have grooves , total height of cast iron top is 334mm - weight-5.2kg. Decorative cast iron pole top starts from bottom with a ring section of dia. 67mm followed by a ring of dia. 75mm, radially incrases to 100mm dia. for a height 15mm,then radially reduces to 46mm for a height 20mm followed by a jack shaped section(45mm(W & 20mm(H), followed by a ring of dia. 60mm which is followed by a Conical section(bottom dia. 40mm & top dia.10mm,140mm(H) with sphere shape(30mm dia.) on top-total height of the pole top is 260mm & weight is 2.5 Kgs.All cast iron weights mentioned are with +/-5% tolerance. Entire pole & Bracket shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized(60 microns Minimum ) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The decorative pedastal to be provided with a suitable size steel base plate. This mounting steel base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. Pole & Cast iron parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint - customised colour Metallaic Grey.

Supplying, erecting & marking SPN MCB 6A to 32A, B- series (for lighting) in provided distribution board

Eathing & Foundation

Supply, Installation, Testing and commissioning of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete.

Supply, Installation, Testing and commissioning & Providing pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia.G.l. Rod complete with all materials

Supplying and erecting G.I. strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joint required.

Supplying and erecting GI earth wire of high purity of different sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall/cable/ conduit with screws in an approved manner.

Supply, Installation, Testing and commissioning of making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 9m & 10m high octagonal /conical GI pole).

Cable

Supplying, erecting & terminating XPLE armoured cable 4 core 10 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe

Supplying, erecting & terminating XLPE armoured cable 4 core 25 sq. mm. aluminium conductor with continuous 5.48 sq. mm.(12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe

Supplying, erecting & terminating XLPE armoured cable 4 core 6 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe

Supplying, erecting & terminating XLPE armoured cable 4 core 50 sq. mm. aluminium conductor with continuous 5.48 sq. mm.(12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe

Supplying, erecting & terminating XLPE armoured cable 4 core 70 sq. mm. aluminium conductor with continuous 8.35 sq. mm. (10 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe.

Supplying & erecting mains with 2x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places.

Enclosers

Supplying & erecting G.I. pipe ‘A’ class 25 mm dia. erected for enclosing PVC armoured cable on wall/pole

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 90 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Street Light Control Panel

Inspection Chamber

Supplying installation and testing of Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and C.I. lid cover of 75 kg with lid and frame fixed in cement concrete.

High Mast

Supplying and erecting 20 m (clear height) High Mast (Top-150mm,Bottom- 460mm) with lowering and raising motorized unit, Vertical lantern carriage assembly suitable for max. 12 nos. luminaries and its control gear box, lightning finial arrangement for fixing aviation light and foundation bolts on provided foundation.

Supplying and erecting Outdoor Stand Mounted Feeder Pillar for highmast of the same manufacturer with 63A TPN MCB incomer,single dial timer switch, 45A TP contactor for automatic switching of luminaries, 2 nos 9A contactors and raise/lower push button, and provision for termination of adequate size of incoming and outgoing cables erected in min. 14 SWG CRCA sheet box powder coated with supporting angles, self-lock, gasket and slanting top erected with CC foundation complete.

Supplying installation and testing of making M- 20 cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq. m at 2 m depth including excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 20 m raising lowering high mast) .

Supplying and erecting LED Flood light fitting of 200W,including lamp,with PF > 0.95,class IP 65 and above Housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete.

Supplying, erecting & terminating XLPE armoured cable 4 core 95 sq. mm. aluminium conductor with continuous 8.35 sq. mm. (10 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe.

Metering Connection

Supplying, erecting & terminating XLPE armoured cable 3½ core120 sq. mm. aluminium conductor with continuous 12.97 sq.mm. (8 SWG) G.I. earth wire complete erected with glands & lugs,on wall/ trusses/pole or laid in provided trench/ pipe.

Supplying and erecting Three phase smart energy meter DLMS compliance with 3x240V 50 cycles AC supply 10-60 A, ISI mark, accuracy class 1.0 with backlit LCD display, measuring & display V, I, kW, kWh, PF, kVA, kVAr, MD, day, week, month & with communication module configurable for GSM/Wi-Fi, IrDA/Bluetooth, complete provided panel with calibration certificate from manufacturer & duly wired with required size of PVC wires.

Supplying & laying (including excavation) 25 cm Dia half round RCC Hume pipe of standard thickness at required depth up to 90 cms. below road / ground surface, for enclosing provided cable & necessary back filling with light ramming to make the road/ground surface as it was (Except bitumen carpet).

Supplying installation and testing of making trench of suitable width and depth in hard murum / tar road for laying provided LT cable up to and including 16 sq. mm complete.

Supplying installation and testing of making trench of suitable width and depth in hard murum / tar road for laying provided LT cable of 16 sq. mm & above and covered with half round hume pipe complete.

FLOATING FOUNTAIN ( Three Tier) at CENTRE

RINGS, NOZZLES & ACCESSORIES

Central High Jet Nozzle made of Brass 300 mm height with ball joint of 40 mm inlet & spray head of 10-15 mtr

900 mm Dia S.S 304 ring With 6 Nos of Crown Jet Nozzles made of Gun metal Chrome plated Spray head approx 6-8 mtr in parboloic shape

1500 mm Dia S.S 304 ring With 9 Nos of Crown Jet Nozzles made of Gun metal Chrome plated Spray head approx 4-6 mtr in parboloic shape

LIGHTING SYSTEM

Supply of nozzle mounted Under Water Lights of 18 W / 12 V DC Super Bright LED Lights with 1 M u/w cabling ( LED Cree/ Luncent/ eqv)

(220volt/12volt) LED driver and power supply to feed the the above light

PUMP, MAINFOLD & SUCTION SCREEN

Monobloc Vertical single stage submersible Pumpset of Capacity of 10kw/15 hp with heavy discharge of 1500 lpm, to feed water Nozzles with manifold ( specially designed for high discharge) SUPPLY : THREE PHASE , 360/440 V, 50Hz

CONTROL PANEL

Indoor type Electrical Panel with Complete accessories such as Voltmeter, Ammeter, circuit transformers MCCB, Contractors ,Starters, push buttons, Indicating Lamp Etc.

FLOAT & ANCHORS

Double layered FRP floats of 2400 mm dia with S.S Intelinked connection & counter sunk arrangement for lights and pumps with attached self standing base frame to enable to withstand the load of the system in dry weather.

PLUMBING WORK

Necessary plumbing work with supply of G.I pipes, fiitings such as coupling, tees, gate valves for complete fountain system

ELECTRICAL WORK

Necessary Elecrtical work with supply complete matrial such as cables, wires, conduits , submesible joints, insulation tapes, earthing materials, etc. ( Max distance of panel 60 mtr from pool)

INSTALLATION & COMMISSIONING

Site Survey, Hydraulic designing, intallation & commissioning charges including Transportaion & On site warranty of fountain equipments.

FLOATING FOUNTAIN ( Musical Componants)

Providing , Supplying and Instaulation of musical componants with all setup (including speakers, cabling, amplifire etc. complete) as per fountain requirment as per directed by engineers incharge.

HT / LT AB CABLE

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of 8 Mtr. Long Pole( ST-410 SP15) IS: 2713 amended up-to date well finished and coated with black bituminous paint upto plant depth and Red-Oxide coated above ground level including Aluminium Paint of approved brand with earthing arrangement through bolt welded on pole of 14mm diameter, provided at height of 300mm above the planting depth which should be 1.5ms (SP 15). Top plate 3mm thick fully welded & bottom plate 35cm*35cm, 5mm thick fully welded.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of 9 Mtr. Long Pole( ST-410 SP15) IS: 2713 amended up-to date well finished and coated with black bituminous paint upto plant depth and Red-Oxide coated above ground level including Aluminium Paint of approved brand with earthing arrangement through bolt welded on pole of 14mm diameter, provided at height of 300mm above the planting depth which should be 1.5ms (SP 15). Top plate 3mm thick fully welded & bottom plate 35cm*35cm, 5mm thick fully welded.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of 120 mm² AB (HT) Cable (3 x 120 +1 x 95 mm²) .

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of 120 mm² AB (LT) Cable ( 3 x 120 + 1 x 16 + 1 x 70 mm²) XLPE (1.1kV, 3+1 C, Al)

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of Heat Shrinkable Outdoor Cable Termination Kit

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of Suspension/Tension Clamp with eye hook

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of Galvinized Nuts and Bolts as per indian standard.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of Danger Plate With Clamps as per Standards wih writing in English & Urdu.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of Anti-Climbing Device with Clamps (GI Barbed Wire (12 SWG) for a distnce of 40 CM at hight of 3.5 meters from GL) , 3.50 Kg per pole.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc for Pole Earthing complete by G.I Pipe 40 mm or GI rod 20 mm , 2.5 mtr long through G.I Strip of standard size.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc for Insulating Piercing Connectors.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc for PG Clamps.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc of Cement bottoming 1:2:4 mix as per specific standards

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of Straight Through Joints.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc of Galvanised Stay Set with 50x8mm stay clamp, guy insulator(2Nos.), anchor plate (200x 200 x 6 mm), nut-bolts, 2 Nos turn-buckles, 1.8m long, 16 mm diameter solid GS stay rod & 7/3.15 mm dia GI stranded wire complete.

Substation

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of Supply of of S.T. poles 9.0 Meter long swaged Type conforming to ST 410 SP-33, IS: 2713 amended up-to date well finished and coated with black bituminous paint upto plant depth and Red-Oxide coated above ground level including Aluminium Paint of approved brand with earthing arrangement through bolt welded on pole of 14mm diameter, provided at height of 300mm above the planting depth which should be 1.5ms (SP 33). Top plate 3mm thick fully welded & bottom plate 35cm*35cm, 5mm thick fully welded.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. for Gapless Surge Arrestor, 9 kV, 10 kA, Lighting Arrestor Set Heavy duty with Plymer Housing, Station type conforming to IEC-99-4 Capable of withstanding Maximum continuous operating voltages (M.C.O.V)

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. for 11KV 200 Amperes, Triple pole switches Gang Operated (G.O. Set) conforming: IS-2544, IS: 5340 (Part-III) and SS: 9921 (Part-I -V)

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc of 11 KV Horn, Gap (fuse 3-phase 200A) as per Relevant IS.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of 1.1KV Grade PVC Insulated Stranded Conductor Un Armoured Sngle Core XPLE FIRLS Type Cable 400mm2 Single Core.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc for 11KV Disc Insulators (Polymer Type) 12 KV , 45KN Complete with fittings..(Lighting Impluse 75 KV positive and 80 KV negative , crepage distance 320 mm).

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of GI Channel/Angle/Flat of sizes including clamps for L.A set/G.O set/HornGap including Red Oxide primer and Aluminium paint of approved brand.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of Galvinized Nuts and Bolts as per indian standard.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc for Earthing of Substation---Excavation of earth pit of dia 650mm & depth 3000 mm, installation of Earthing pipe of 40 mm Nominal bore & 4mm wall thickness & length 2.5 mtr long as per IS 1239. GI strip for neutral earthing of size 25mm*3mm for connection of transformer body, G.O Set & lightening Arrestor as per IS 2629/85, GI nuts & bolts, refilled with earth enhancement materials & earth chamber made of brick masonry with RCC slab cover.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. for TransformerPad/G.I Channel Bedding having bearing capacity of 300Kg.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc for 11KV Pin insulators (Polymer Type) 12 KV , 5KN Complete with fittings..(Lighting Impluse 75 KV positive and 80 KV negative , crepage distance 320 mm) with pins

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc for LT Distribution Box for 630/400/250 kVA DTR with MCCB & SFU's for Outgoing Circuits.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of Galvinized Nuts and Bolts as per indian standard.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc for wedge connectors/PG Clamps.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of Danger Plate With Clamps as per Standards wih writing in English & Urdu.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc. of Anti-Climbing Device with Clamps (GI Barbed Wire (12 SWG) for a distnce of 40 CM at hight of 3.5 meters from GL) , 3.50 Kg per pole.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc of Cement bottoming 1:2:4 mix as per standard specifications.

Supply, installation testing,and commissioning icluding labour, carriage, friegt, taxes, duties etc of Sundry items like Aluminum lugs, Jumpers,Binding tape

Dismantling

Dismantling of existing ACSR 100/50/30 Sqmm LT and transportation back to Divisional Stores. As per Instructions of Electrical Incharge.

Dismantling of existing ACSR 100/50Sqmm HT and transportation back to Divisional Stores. As per Instructions of Electrical Incharge.

Dismantling of existing PCC/Wooden Pole and transportation back to Divisional Stores. As per instruction of Electrical Incharge.

Dismantling of existing ST pole 8/9 mtr and transportation back to Divisional Stores. As per instruction of Electrical Incharge.

Dismantling of existing LT shakle Insulators with D clamps complete and transportation back to Divisional Stores. As per instruction of Electrical Incharge.

Dismantling of existing Stone Masonary Pole Bed/Wooden Bed and transportation back to Divisional Stores. As per instruction of Electrical Incharge.

Dismantling of existing Ch. Iron V-X arm, X-arm including clamps & braces (GI)

Dismantling of existing 11 kV Pin Insulators complete and transportation back to Divisional Stores. As per instruction of Electrical Incharge.

Dismantling of existing 11 Disk Set and transportation back to Divisional Stores.As per instruction of Electrical Incharge.

Hassan Road Construction Co Pvt Ltd