Ttkulam 6th Finance 2022-2023

Amount

Earth work excavation and depositing on the bank with initial lead and lift of 10 metres and initial lift of 2 metres in hard stiff stiff clay stiff block cotton hard red earth murram, gravel stoney earth and earth mixed with small size boulders and hard gravelly soils (SS 20 B) etc., complete as per standard specification

Plain cement concrete Using 1:4:8 mix ( One cement , four Sand and Eight aggregates) using 40 mm ISS HBG metal including cost and conveyance of all materials to work site and all labour charges for mixing, laying,consolidating and curing etc complete as per the standard specifications. TNDSS NO: 28 V, VI (S2) V,VI (S5A) VII

Random rubble masonry in c.m 1:5 (one cement five sand) using best new rough and bond stones including simultaneous pointing above ground level with the same mortor and cost of all materials and labour charges etc,complete as per SS.

Rough stone dry Packing for aprons and revetments using rough stone including cost of all materials and labour charges etc,complete as per SS. No: 217.

Brick work in cement mortar 1:5 mix using (One cement and five sand) using best quality of II class chamber bricks of size (8 3/4"x41/4"x 23/4" ) for foundation including curing cost and conveyance of all materials to site and all labour charges etc., complete as per standard specification

Supplying, fabricating and placing in position of mild steel or TMT rods, including cost of steel and binding wire and all labour charges for cutting, bending, tying and placing in position etc, complete as per SS. TNDSS NO: 97 V,VI (S6) VII (S6) VII-3

Supplying and erecting Steel Centering including necessary supports for plane sufaces in foundation and in all floors for RCC Column Beams , using mild steel sheets of suitable size 90cm x 60cm and 10 gauge stiffened with including all labour charges etc., complete. (Plain surface)

Supplying and erecting Steel Centering including necessary supports for plane sufaces in foundation and in all floors for RCC Column Beams , using mild steel sheets of suitable size 90cm x 60cm and 10 gauge stiffened with including all labour charges etc., complete. (RCC work)

Supplying and erecting Steel Centering including necessary supports for plane sufaces in foundation and in all floors for RCC Column Beams , using mild steel sheets of suitable size 90cm x 60cm and 10 gauge stiffened with including all labour charges etc., complete. (Square column)

R.C.C.1: 1 1/2:3 mix using 20mm ISS HBG metal including Cost and conveyance and all labour charges for mixing laying finishing and curing etc complete but excluding cost of steel & Centering charges etc., complete as per SS

Plastering with cm 1:3 mix (One Cement and Three Sand), 10mm thick cost and conveyance of all materials finishing, curing and all labour charges etc complete as per standard specification.

Plastering with cm 1:4 mix (One Cement and Four Sand), 12mm thick cost and conveyance of all materials finishing, curing and all labour charges etc complete as per standard specification.

Supply and fixing Terracota Jally of size 20 x 20 x 0.75mm of approved pattern including pointing finishing, curing etc. complete complying with standard specification directed by the departmental officers. (as per PWD sanctioned DR NO 255/11-12)

Supply and fixing of steel doors & grill workincluding cost and conveyance of materials etc. complete.

Painting two coats with ready mixed Plastic Emulsion Paint S.I.358 Plastic emulison paint of'approved quality and colour over a priming coat, including thorough scraping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required including cost and conveyance of all materials etc.and all lobour charges etc.complete as per Standard specification and as directed by the departmental officers. TNBP No:66-A (Sl.No.358)

Floor Finishing First Quality Design Ceramic tiles of All colours of sizes 305mm x 305mm x 6mm. laid in cm 1:3 mix 10mm thick and pointing with white cement using 0.4kg/sqm including finishing the joint and pointing flush with tiles surface etc complete

Dadooing with glazed tiles of 150mm*150mm*6mm size of approved quality and colour set in c.m 1:2 (one cement and two sand) 10 mm thick and pointing with white cement using 0.4 kg /m2 neatly as directed - including cost of all materials and labour charges etc complete as per SS

Supplying & Fixing in position of white glazed Indian type water closet with 'P' (or) 'S' trap and Orissa slope set in brick jelly cement concrete 1:4:8 100mm thick using 20mm thick brick jelly ISS gauge and finished to sludge out any leakage and defalut including cost of WC 'P' (or) 'S' trap and foot rest etc., complete.

Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.

Supplying and fixing of steel TRUSSES work using MS angles and 'T' sections each according to design approved by the departmental officers including cutting, welding and cost of conveyance and all materials to work site.

Supply and fixing of Galvalum sheet (Pre painted) 6mm thick including 15cm lapping roofing with necessary 'J' bolt and nut, bitumen washer and Screws if wooden baterns including cost and conveyance of all materials and all labour charges etc Complete complying with Standard specifications.

Supply and delivery and fixing of HDPE tank as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc. (1000 litre)

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC.unsheathed Cu. Conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A F.T. switch with painting of suitable Colourfor open PVC light point / fan point (For electronic regulator) (5 points per coil) (SD-18)

Wiring with 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 x l00 x 113 mm TW switch box for 5 A 3 pin non inter locking Wall socket with 5A Flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC plug point. (SD-36)

Supply and fixing of fancy glass shade and 11W CFL for BH point. (80)

Supply and fixing of single box type 4'40 W flu fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting. (SD-88)

Supply and fixing of TNEB meter Board suitable for 32A Three Phase service connection with 3 Nos. 32A Fuse unit (500V) 32A neutral link and earth link (1" x 1/8" Copper flat) on TW plank of size 600mm x 450mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit. (SD-127)

Supply and fixing of 3 Phase 32A aerial fuse unit for 3 Nos 32A fuse units (500V) on suitable MS sheet covered with 6mm thick hylem sheet on suitable angle iron work the tapping pole with necessary clamps. (SD-132)

Supply and delivery of following PVC / G.I pipes and specials

90mm PVC pipe

25mm PVC pipe

25mm PVC coupler

25mm PVC Elbow

25mm PVC bend

25mm PVC Tee

25mm End cap

20mm x 15mm Reducer

25mm x 20mm Reducer

20mm x 15mm Reducer Tee

25mm x 20mm Reducer Tee

20mm x 15mm Reducer elbow

25mm x 20mm Reducer elbow

25mm Jet Nipple

75mm PVC Elbow

75mm PVC Elbow with Door

75mm PVC Tee

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work. (25mm)

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works) - SD Tap

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supply and fixing in position of best Indian make colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position Indian make white glazed earthenware squating type urinal of best quality and approved make including dismantling masonry, if necessary and re-doing the same to original condition, etc., complete complying with standard specification. (The squatting urinal should be got approved by the Executive Engineer before use on works).

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of PCC 1:4:8 and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class ‘B’ class GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD-233)

18 W LED Tubelight for T8 Fitting Single side (TWAD schedule of rate 2022-2023)

AC Exhaust Fan 300mm (12”) Sweep (Light Duty) (TWAD schedule of rate 2022-2023)

YESUDHASAN STEWARD ISAAC SAM (BID ID -1047060)