PROVISION OF COVERED SHED NEXT TO ANTE ROOM AT OFFICERS MESS AT AF STATION DALHOUSIE

Amount

Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar (1:6) with old size bricks complete all as specified and directed by Engineer-in-Charge.

Rendering 15mm thick cement plaster in cement mortar (1:4) on brick or concrete surfaces finished and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Preparing of old plastered or un plastered surface of walls and applying distempering two coat on walls and with oil bond distemper, white or tinted over and including 5 mm thick chalk whiting on plastered surfaces complete all as specified and directed by Engr-in-Charge.

Preparation of new surfaces as per manufacturer’s instructions and applying two coats of exterior acrylic paint of any shade over a coat of primer over new plastered surfaces of walls complete all as specified and directed by Engr-in-Charge.

Demolition of concrete in ground floor not exceeding 15cm in thickness below or above ground level including floor finish such as tiles of any thickness and any description etc. complete all as specified and directed by Engr-in-Charge.

PCC 1:2:4 type B-1, 40mm thick using 20mm graded crushed aggregate), as in sub base even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

Screed bed or bedding layer of mortar 15mm thick in cement mortar (1:4) complete all as specified and directed by Engr-in-Charge.

Virified ceramic tiles double charged 10 mm thick (square /rectangular) polished size of tiles 600x600x10 mm , in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and include 20 mm thick secreed bed in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.

Coloured chequered cement concrete rubber finished tiles 250x250x22-25mm thick,with grey cement and pigment set , jointed and pointed in neat cement slurry in floors over and include 15 mm thick secredd bed in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

Supply and fixing anodised aluminium powder coating minimum thickness of powder coating 50 micron frame for doors, windows, ventilators with one or more rebates including joining cleats for fixing etc complete all as required at site or directed by Engr-in- Charge.

Supply and fixing anodised aluminium powder coating minimum thickness of powder coating 50 micron door shutters (sliding type Including locking Arrengement ), aluminium section weighing 0.55 kg/m including necessary joining cleats glazing clips rubber packing, anodised aluminium beading screws,including top rail etc complete all as specified and directed by Engr-in-Charge.

Supply and fixing of 4 mm thick tinted/plain glass for aluminium windows/doors having each pane exc 0.5 sqm incl complete fittings complete all as specified and directed by Engr-in-Charge.

Supply and fixing of 5 MM thick plain colour pvc backelight sheet in strips channel feathered at the for fixing on aluminium frame partition complete all as specified and directed by Engr-in-Charge.

Supply and fixing of anodised aluminium snap grid frame work for false ceiling including hanging arrengements with butterfly clip and 4 mmdia GI wire complete all as specified and directed by Engr-in-Charge.

Non-asbetos ceiling board 0.595 x0.595 mtr x 4mm thick designer boards of everest or equvalent fixed with powder coated GI framing including drilling hole for fixing GI frame including 4mm GI wire suspender and clips complete all as specified and directed by Engr-in-Charge.

Supply and fixing of Pre painted galvalume aluminum zinc coating GI based Plain steel sheet 0.910 mm thick Pre- Moulded Semi cercular Structure Factory Made of an colour haveng strength of 550 Mpa as in roof covering/cladding etc fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

Supply and fixing of Pre painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.910 mm thick of an colour haveng strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

Supply and fixing of 0.63mm thick galvanised, plain mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed by Engr-in-Charge.

Supply and fixing of rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantries, rails, fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections), including distance pieces, cleats etc. including cutting, welding etc. confirming to Fe – 410 – W(Gde E - 250) quality 'B' complete all as specified and directed by Engr-in-Charge.

Supply and fixing of rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe – 410 – W(Gde E - 250) quality 'B' complete all as specified and directed by Engr-in-Charge.

Preparation of New or previously un-treated steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

Supply and fixing of 5 mm thick PVC sheet fillet of width 35 mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and directed by Engr-in-Charge.

Supply and fixing solid PVC wall lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvant cement and fixing at site on PVC frame as per specification and drawing complete all as specified and directed by Engr-in-Charge.

Supply and fixing of 110mm PVC bends any radius with oval access door complete all as specified and directed by Engr-in-Charge.

Supply and fixing of 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed by Engr-in-Charge.

Concealed point wiring on wall and surface on ceiling/roof with necessary fixing arrangements with PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade drawn in and including rigid non metallic white / ivory PVC conduit medium grade ISI marked not less than 19 mm dia with all conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dolly and bakelite laminated sheet 3mm thick ISI marked for fixing of switches / sockets, fan regulators, wall mounting fittings, door bell & bulkhead/telephone socket etc with MS screw and cup washers including PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade for continuous earthing including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of peris/ Putti or distemper / colour wash with same existing colour surfaces all as specified and directed by Engineer-in-Charge for the following:- (a) One light, fan, bell point controlled by one switch.

(b) One 5 Amp socket point controlled by one switch on same board complete all as specified and directed by Engr-in-Charge.

(c ) 5 Amp independent socket point controlled by one switch complete all as specified and directed by Engr-in-Charge.

All as per item No 26.00 here-in-before above but for power point wiring with 2.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 1.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable as continuous earth lead complete all as specified and directed by Engr-in-Charge.

Switch flush type single pole one way 5 Amps, 240 volts, white finish, ISI marked complete all as specified and directed by Engr-in-Charge.

Switch flush type single pole one way 15 Amps, 240 volts, white finish, ISI marked complete all as specified and directed by Engr-in-Charge.

Socket outlet 5 pin, 5 Amps, 240volts flush type white finish , ISI marked specified and directed by Engr-in-Charge.

Socket outlet 2 in 1, 3 pin, 5 &15 A, 240 volts, flush type white finish, ISI Marked complete all as specified and directed by Engr-in-Charge.

Supply and fixing of Bell push, flush type 5 Amps white finish, ISI Marked complete all as specified and directed by Engr-in-Charge.

Supply and fixing of Door bell multi music type 230V, single pole, ISI Marked complete all as specified and directed by Engr-in-Charge.

Supply and fixing of Ceiling rose, surface backlite, 65 x 20 mm 3three terminal ISI Marked complete all as specified and directed by Engr-in-Charge.

Supply and fixing of Lamp holder insulated body with back plate suitable for angle / batten fitting ISI Marked complete all as specified and directed by Engr-in-Charge.

Supply and fixing of Sheet metal enclosure VTPN MCCB DB 12 way, 415 V (vertical type) with bus bar double door type IP 43 - IK 09 for DB when MCBs & MCCB 100 Amps (as incomer) fixed properly on / in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs for cables/wires complete all as specified and directed by Engr-in-Charge.

Supply and fixing of Double door metallic sheet metal enclosure for DB when MCBs to be used SPN 12 ways, 240 V with 200Amps rated bus bar complete fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs of cables/wires complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repalcement MCB SP 240 volt 6 Amp to 32 amp 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed by Engr-in-Charge.

All as per item srl No 38 above but SPN 16-32 Amps complete all as specified and directed by Engr-in-Charge.

Supply and fixing of MCCB 100 Amps, 3 Pole, 415V, 25 KA thermal adjustable type with short circuit and overload protection complete all as specified and directed by Engr-in-charge.

Supply and fixing of Sheet metal enclosure , 32A single pole and neutral with a two pin and earth plug and socket complete in metal clad board (Industrial type) with one single pole MCB 32 Amp fixed properly complete all as specified and directed by Engr-in-Charge.

Sub main wiring with two single core PVC-FRLS insulated unsheathed multi stranded copper conductor cable of size 10 sqmm drawn in and including rigid non metallic white / ivory PVC conduit medium grade ISI marked not less than 19 mm dia with all conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc laid in concealed position with 2.5 Sqmm PVC-FRLS insulated unsheathed multi stranded copper conductor as a continuous earth wire including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of peris/ Putti or distemper / colour wash with same existing colour surfaces complete all as specified and directed by Engr-in-Charge.

Recess mounting LED luminaries 34/36 Watt(2'x2'), 240 volts with more light distribtuion and clutter free ceiling with powder coated CRCA sheet steel white powder coated housing with square in a perforated metallic frame complete all as specified and directed by Engr-in-Charge.

Supply and fixing of Decorative ultra slim linear LED lighting fixtures with extruded polycorbonate environmental friendly energy saver LED light fitting 1x20/22 watt (4'), 230 Volts, single tube mounting including LED Tube 20/22 Watt complete with electronic driver spring loaded rotory type lamp holder, end cover, connector box etc and accessories, prewired, LED including required fixing arrangements and electrical connection with three core copper cable from ceiling rose to led light fitting complete all as specified and directed by Engr-in-Charge.

All as per item ser item No 44 above but 1x10/12 Watt (2') complete all as specified and directed by Engr-in-Charge.

Supply and fixing of Decorative LED wall light fixture made up of polycorbonate body suitable for 9 W LED lamp B22 base, 230 Volts, including LED lamp 9 Watt complete and electrical connection with twin core copper cable from ceiling rose to led light fitting complete all as specified and directed by Engr-in-Charge.

Supply and fixing building security light fitting new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 of 25 watt LED, 240 Volts complete all as specified and directed by the Engr-in-charge.

Supply, fixing, installation and testing of ISI marked, energy efficient, water heater storage type, electrically operated, single phase, 50 Hz (BEE 5 star rating), complete of 25 Ltr capacity with and including supply and fixing, wire armoured 450 mm long, 15 mm dia brass coupler etc, flexible pipe suitable to withstand upto 100 degree celcius for hot and cold water, anchor fastner - 04 Nos of suitable size , 3 core PVC insulated, FRLS multistranded copper conductor cable and plug top 15 Amps capacity complete in all respect all as specified and directed by Engr-in-Charge. Note : Old unserviceable geyser is to be deposited to MES store yard.

Supply and fixing of heavy duty exhaust fan AC single phase 230/240 V of size 300 mm sweep 1400 RPM with louver & shutter including necessary grouting on wall complete and making good the wall surface after fixing of exhaust fan all as specified and directed by the Engr-in-charge. Note : Old unserviceable Exhaust fan is to be deposited to MES store yard.

Supply and fixing of PVC exhaust fan AC single phase 230/240 V of size 250 mm sweep 1400 RPM with louver & shutter including necessary grouting on wall complete and making good the wall surface after fixing of exhaust fan complete all as specified and directed by the Engr-in-charge.

Earthing complete with M.S. galvanized earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below normal GL) with top edge of the earth plate not less than 1.5M below normal GL, connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts & washers of GI or steel incl excavation, PCC (1:3:6) type C-1 chamber with RCC cover (1:2:4) type B0, 40 mm thick reinforced with 6 mm dia bar, 3 Nos. both way, 15 mm dia light grade GI protection pipe, funnel with wire mesh,watering pipe of size 20 mm dia med. grade, lugs, main Earthing lead upto 7.5 mtr incl. Charcoal dust, salt etc. all as shown in electrical plate No. 3 of SSR Part-I, 2009 specification. Note : Result of the earthing should be less then 4 ohms if not achieved the new earthing to be carried out without any extra cost.

Supplying and fixing of copper strip 20x3mm complete with saddles/ insulators made out of PVC or fibre and fixing screws for roof conductor/down conductor including welding or brazing for joints complete all as specified and directed by Engineer-in-Charge

Supplying and fixing of GI tubing light grade 25mm dia, cut to size and bent to shape all as required at site including fixing arrangement with necessary clamps of required size at site and providing appropriate size of insulators to pipe from foundation of air termination rod complete all as specified and directed by Engr-in-charge.

Air termination single pointed copper rod 12mm dia and 300mm long complete all as specified and directed by Engineer-in-Charge

Test point terminal block made of gun metal or phosphorus bronze of size 75X75X6mm drilled and screwed including 03 Nos 8mm dia 25mm long hexagonal head screw complete all as specified and directed by Engr-in-charge

Earthing complete with copper earth plate electrode 600x600x3.15 mm thick buried directly in ground (Earth pit not less than 2.25 Mtr deep below normal ground level ) with top edge of earth plate not less than 1.5 Mtr below normal ground level connected to copper strip 20X3 mm as earth lead by means of bolts, nuts washers and check nuts of steel/GI duly protected with 40 mm bore light grade pipe upto main board , 20mm bore watering pipe light grade with CI/MS funnel and wire mesh including excavation , earth work in any type of soil and removing the surplus soil to a distance not exceeding 50 Mtr, add charcoal dust and common salt after mixing with BFC (Back Fill Compound) inadeqate quantity as recommended by the manufacturer or as diirectred by the Engr-in-charge all as shown in electrical plate No. 03 of SSR part-I 2009 having pit in PCC 1:2:4 type B-1 including angle iron frame made of angle iron of size 40x40x6mm grouted in PCC pit for CI cover of required size, funnel with wire mesh complete and all as specified and as directed by Engr-in-charge.

Supply, laying testing and connecting 25 Sqmm 4 Core XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured heavy duty electrical cable with aluminium conductor, 1100 volts grade laid in trenches/ducts/wall or through pipe with suitable size of cable glands, crimping type cable lugs complete all as specified and directed by Engr-in-Charge.

Supply, laying testing and connecting 70 Sqmm 3.5 Core XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured heavy duty electrical cable with aluminium conductor, 1100 volts grade laid in trenches/ducts/wall or through pipe with suitable size of cable glands, crimping type cable lugs complete all as specified and directed by Engr-in-Charge.

Excavation in trenches in any type of soil, not exceeding 1.5m wide and not exceeding 1.5m in depth; for foundation, laying of cables and getting out complete all as specified & as directed by Engineer-in-charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm each layer complete all as specified and directed by Engineer-in-Charge

Removing excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed by Engineer-in-Charge

Sand cushioning to under ground cable 8 cm thick layer below the cable and 15cm thick above the cable complete all as specified and directed by Engineer-in-Charge

Brick protection with well burnt sub class ‘B’ brick a butting each other( width wise) across the cable laid in trenches complete all as specified and directed by Engineer-in-Charge

Material & labour for tubing GI light grade 50mm bore laid in trenches, ducts, floor for protection of cable, fixed to wall or poles including fixing arrangement all as required at site complete all as specified and directed by Engineer-in-Charge

M/S MULTI ENGINEERS

m/S Varun Gupta

M/S Ajay Kumar Mahajan

pardeep singh marwaha