EMERGENT WORK DUE TO SWACCH SURVEKSHAN 2026 FOR PROVIDING AND FIXING OF PUBLIC HEALTH FIXTURES, ELECTRICAL FIXTURES AND CIVIL WORKS AND CIVIL WORKS AND OTHER ALLIED WORKS AT VARIOUS PUBLIC TOILET BLOCKS IN MARKETS AT SECTOR 16 AND 17 CHD

Demolishing brick tile covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 metres lead (DSR No. 15.26)

Demolishing mud phaska in terracing and disposal of material within 50 metres lead (DSR No. 15.27)

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge 15 mm to 40 mm nominal bore (DSR No. 15.44.1)

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in Charge (DSR No. 14.82)

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead (DSR No. 15.52)

Dismantling Wash hand basin with existing CI brackets & fitting of all sizes including handing over the material to department all complete as per directions of Engineer-in-Charge.(Extra Item) (NSI)

Providing and fixing soil, waste and vent pipes 100 mm dia Sand cast iron S&S pipe as per IS: 1729 (DSR No. 17.35.1.1)

Providing and fixing soil, waste and vent pipes 75 mm diameter Sand cast iron S&S pipe as per IS: 1729 (DSR No. 17.35.2.1)

Providing and fixing Drip Seal Joints for HCI pipes of size 100 mm including the cost of yarn, caulking complete in all respect sand cast iron/centrifugally cast (spun) iron pipes & fittings of diameter (NSI)

Providing and fixing plain bend of required degree : 100 mm dia Sand cast iron S&S as per IS - 1729 (DSR No. 17.39.1)

100 mm dia (DSR No. 17.39.1.1)

75 mm dia (DSR No. 17.39.2.1)

Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : (DSR No. 17.61)

100 mm dia (DSR No. 17.61.1)

75 mm dia (DSR No. 17.61.2)

Cutting holes up to 30x30 cm in walls including making good the same:With common burnt clay F.P.S. (non modular) bricks (DSR No. 18.76.1)

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof (DSR No. 18.77)

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors 100 mm inlet and 100 mm outlet Sand Cast Iron S&S as per IS- 1729 (DSR No. 17.60.1.2)

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall (DSR No. 18.11)

15 mm dia nominal bore (DSR No. 18.11.1)

20 mm dia nominal bore (DSR No. 18.11.2)

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : (DSR No. 18.46)

15 mm nominal bore (DSR No. 18.46.1)

20 mm nominal bore (DSR No. 18.46.2)

25 mm nominal bore (Dsr 18.46.3)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 20 mm nominal bore (DSR No. 18.17.1A)

32 mm nominal bore (DSR No. 18.17.2)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 20 mm nominal bore (DSR 18.18.2)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete in all respect of make kajaria, orient bell (DSR No. 8.31)

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. (DSR No. 11.56.1)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 500x500 mm (DSR No. 11.41.1)

Chequerred precast cement concrete tiles 22 mm thick in footpath &courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).[For Barrier Free Toilet Block] Note: Guiding block 300mm away from sliding door Dark shade pigment using ordinary cement (DSR No. 11.20.3)

Making nosing/Moulding on edges of granite marble wherever required complete in all respect as per the entire satiusfaction of Engineer in charge (NSI)

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. (DSR No. 8.5)

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as Directed, within a lead of 50 m All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia (DSR 2.10.1.2)

Regrading terracing of mud phaska covered with tiles or brick, in cement mortar by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1:3 (1 cement : 3 fine sand), including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded), all complete as per direction of Engineer-in-Charge (DSR No. 14.13)

Extra for Brick Tiles @30% Of the total area (NSI)

Flush pointing with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement for flat tile bricks on top of mud phaska :14.18.1 With F.P.S. brick tiles (DSR No. 14.18.1)

Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete With residual type petroleum bitumen of grade VG -10 (DSR No. 12.15.1)

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :In 75x75mm deep chase (DSR No. 12.21.1)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. (DSR No. 12.22)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) (DSR No. 13.47.1)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete (DSR No. 13.80)

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete (DSR No. 13.91)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including water thinnable priming coat with cement primer (DSR No. 13.41.1)

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR No. 19.30.3.1)

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 150 mm diameter (DSR 19.1.2)

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR No. 19.4.1.1)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design 150 mm diameter S.W. pipe (DSR 19.2.2)

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete For pipes 100 to 250 mm diameter (DSR 19.21.1)

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Rectangular shape 600x450 mm internal dimensions (DSR No. 19.19.1.1)

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below (DSR No. 15.12.1)

Providing and fixing factory made PVC door frame of Size 75x50 mm of Rajshri plastiwood WPC ( Wood plastic composite) single extruded solid door frame single rebate in plain colour to entire satisfaction of Engineer-in-charge (NSI)

Providing and fixing factory made 30 mm thick PVC flush door shutters made out of (Rajshree plastiwood pre- laminate (both side decorate) 5mm thick rigid pvc foam sheet, frame shall be made out of 19x19mm MS Square tube of 19 gauge & inside 20mm thick pvc hollow profile filled along tube frame, 5mm rigid PVC foam sheet fixed and pressed machincally on both side of frame with approved quality of adhesive. all the edges of door shutter shall have 5mm thick rigid pvc foam sheet lipping in double layer. item includes powder coated MS butt hinges 100x58x1.9 mm fixed with bright finish or black enamed 40mm / 20mm mild sheet screws as per requirment to entire specifications of Engineer-in-charge. Decorative finish (both side wood grained finish) (NSI)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10 kg/ sqm) (DSR No. 21.3.1)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 200x10 mm ( DSR No.9.97.3)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete 125 mm (DSR No. 9.100.1)

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete 300x16 mm (DSR No. 9.96.1)

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete Twin rubber stopper (DSR No. 9.101.2)

Providing and fixing grabe rail of stainless steel pipe 1-1/4" and fitting of grade AISI 304 as per JIS standard 3448 including fitting and fixing of pipe with clamps at 1.00 m spacing including cutting and making good the walls complete as per direction of Engineer-in-charge. (NSI)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap (DSR No. 17.7.4)

Extra over & Above Item no 17.7.4 of DSR for using under counter washbasin of size 550x445x190mm as per archtechural drawings, code X0494 or parryware (niagara) model with auto closing piller cock system code G 2013A1 of parry ware (lapis neo) with adjustable brackets ( special for under counter) to entire satisfaction of Engineer-in-charge. (NSI)

Difference in rate for providing and fixing auto closing systerm code G201 3A1 or Parryware (Lapisneo) instread of ordinary piller cock systerm to be used in handicaped toilet. (NSI)

Providing and fixing C.P. Bras angular stop cock of 15 mm nominal bore (NSI)

Providing and fixing white vitreous china ceramic flat back half stall flow sensor urinal wall mounted of size 580x380x350mm with all fitting required, standaed size CP Brass flush pipe,with automatic flushing system speaders, auto closing ahle cock, CP dome waste 32mm, GI waste pipe 32mm, clamps (all CP Bras) including painting of fitting complete in all respect (NSI)

Providing and fixing CP brass auto closing concealed urinal press matic taps complete in all respect as per the entire satiusfaction of Engineer in charge (NSI)

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete (DSR No. 17.31)

Providing and fixing urinal partition 10mm thick High Stainless Steel of size 1.5 x 2.75 fixed in postion with clams holding the Steel Partition All exposed edges to be grinded with smooth finish to the entire satification of engineer-in-charge including carriage of material to site of work. to the entire satification of engineer-in-charge including carriage of material to site of work. [Fixed on slopping back wall before fixing ceramic tiles] (NSI)

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. (DSR No. 17.22A)

Providing and fixing of in position best indian make ISI marked 15mm CP brass extionsion nipples including the cost of CP flange complete in all respect as per the entire satisfaction of Engineer in charge (NSI)

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests (DSR No. 17.1.1)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid (DSR No. 17.2.1)

Providing and fixing to the inlet mouth of rain water pipe cast iron gratting 15cm diameter and weighing not less then 4.40 gram. DSR : 12.44

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (DSR 18.48)

Providing and fixing of water meter cover made out of MS angle frame 25mmx25mm shutter 20mmx20mmx5mm MS sheet 18 gauge with locking arrangement primer painting complete in all respect as per the entire satisfaction of Engineer in charge (NSI)

Providing and fixing acralic sheet with silver remark engraving plate 12"x18" in postion at required place to the entire satification of Engineer-in-charge. (NSI)

Providing and fixing Sun board printing with lamination on 5mm sun board of size 6' x 2' to be fixed at the height of 12' from NGL, leveled in postion to the entire satification of Engineer-in-charge (NSI)

Providing and fixing acralic sheet with silver remark engraving plate 12"x12" in postion at required place to the entire satification of Engineer-in-charge. (NSI)

Providing and fixing Sun board printing with lamination on 5mm sun board of size 24" x 30" to be fixed at the height of 12' from NGL, leveled in postion to the entire satification of Engineer-in-charge (NSI)

Providing and Fixing C.P. brass bib cock of approved quality conforming IS:8931 (DSR : 18.49)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 32 mm dia (DSR : 17.28.1.1)

Providing and fixing of Exhaust fan Make: crompton/Havells complete in all respects including the cost of wiring and switches etc. Size 9" double ball bearing. (NSI)

Providing and fixing the louvers complete with frame for exhaust fan of 12" diameter. (NSI)

Providing and fixing of ceiling fan of size 48" Make : Crompton/Havells (NSI)

P/F of LED Tubelights complete set type 36W ,L=4ft, Make : Crompton/Havells (NSI)

P/F of 1.5mm single core PVC insulated copper cable for wiring at Toilet Block (NSI)

P/F of 0.75 mm single core PVC insulated copper cable for earthing at Toilet Block (NSI)

P/F of LED Round Concealed Light complete set type 15W ,Make : Crompton/Havells (NSI)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.(DSR No. 1.21 E)

20mm (DSR No. 1.21.2 E)

25 mm (DSR No. 1.21.3 E)

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. (DSR No. 1.22 E)

75 mm X 75 mm X 60 mm deep (DSR No. 1.22.1 E)

100 mm X 100 mm X 60 mm deep (DSR No. 1.22.2 E)

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required. (DSR No. 1.23 E)

5/6 amps switch (DSR No. 1.23.1 E)

3 pin 5/6 A socket outlet (DSR No. 1.23.4 E)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc.as required. 8 Module (125mmX125mm) (DSR No. 1.27.5 E)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. as required. (DSR No. 12.43)

75mm (DSR No. 12.43.1)

110mm (DSR No. 12.43.2)

U-PVC pipes (working pressure 4 kg / cm²) Single socketed pipe (NSI)

75 mm dia. (NSI)

110 mm dia (NSI)

Supplying and fixing modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (DSR No. 1.24)

15/16 a Switch (DSR No. 1.24.3)

3 pin 5/6 A socket outlet (DSR No. 1.24.4)

6 pin 15/16 A socket outlet (DSR No. 1.24.5)

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular swith, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B (DSR No. 1.10.2 E)

Wiring for light/ power plug with 2X4 sq mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq mm FRLS PVC insulated copper conduct single core cable for loop earthing as required (DSR No. 1.12)

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double Pole (DSR No. 2.10.3 E)

Supplying and fixing metel box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. 200 mm X150 mmX100mm deep (DSR No. 1.22.11)

Supplying and fixing following way, single pole and netural, sheet steel, MCB distribution board consurmer unit 240 volts, on surface/reess, complete with timed copper bus bar netural bus bar, earth bus bar, hinged front acrylic cover for the MCB knobs, detachable gland plate, interconnections, phosphatized and powder painted including earthling etc. as required (But without MC/ PCCB/Isolator) 2*4 way (DSR No. 2.7.4)

Making suitable size wall niche minimum 2'x3'-0'' including cement plastering from inside of niche, wooden plank for sheet metal, iron clad switch gear includng the cost of PVC shutter with locking arrangement, Chowkat complete in all respects (NSI)

Providing and fixing 50 watt LED light including cost of wiring, labour and bracket out side on the wall complete in all respects. (NSI)

Providing and fixing of automatic hand drier make of approved quality complete in all respect as per the satisfaction of engineer in Charge. (NSI)

Providing and placing PVC mat 15mm thick (NSI)

Providing and fixing of dustbin in WC cabins and under wash basinscomplete in all respects. (NSI)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required In gratings, frames, guard bar, ladder, railings, brackets, gates and similar work (10.25.2)

Providing and Fixing IRC jali made of mesh wire 1" x 1" welded in frame made out of MS flat 25mm in existing ventilation complete in all respects including the cost of primer , painting etc (NSI)

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade Two or more coats on new work: DSR Item No. 13.65.1

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge (DSR No. 16.90)

Providing and fixing 25mm thick pre-laminated medium density fibre board exterior grade (Grade-I) IS:14587:1998 marked with one side decorative and other side balancing lamination for cupboard shutters edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand including ISI marked nickel plated bright finishing M.S piano hinges conforming to IS:3818 marked with necessary screw etc all complete (DSR No. 9.159)

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms (DSR No. 17.71)

Providing and fixing Sanitary Napkin Vending Machine, incinator, Battery and happy days pads complete in all respect as per the entire satiusfaction of Engineer in charge (NSI)

Providing of fixing of SS stainless steel 304 grade house indicator board wiht 4mm thick ACP sheet covered by relective sheet in blue color prismatic high resolution sheet/tape of type XI both sides including house numbers in white colour covered by 1.5mm thick poly carbaonate sheet both sie . the sheet is to be fixed in display frame size of 1'-10" x1' -0" whith arrow formation at one side as per drawing of SS pipe of 25mm dia with internal support for ACP sheet with proper welding fixed with reveits as required the display frame is to be welded with vertical SS pipe of 40mm dia with height of 3'-4" feet above the groud level and 1'- 0" below ground level. the rates also include cost of 9" long anchorage piece embedded in cement concreate 1:2:4 block size of 1'x 1'x 1'-3" complete in all respects to the entire staisfaction of EIC (NSI)

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape,raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. With cement mortar 1:4 (1 cement : 4 fine sand) (DSR No. 14.1.1)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources) (DSR No. 4.11)

10 cm thick (average) mud phaska of damped brick earth on roofs laid to slopeconsolidated and plastered with 25 mm thick mud mortar mixed with bhusa @35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 1 cow dung) andcovered with flat tile bricks, grouted with cement mortar 1:3 (1 cement : 3 finesand) mixed with 2% of integral water proofing compound by weight of cement and finished neat: With common burnt clay F.P.S.(non modular) brick tile of class designation 10 (DSR 12.16.1)

Providing and Fixing of Customer feedback device having 3 nos. push buttons , metal body,wall mounted,mahine use for givng rating on public toilet including terminal box, electrical parts,wiring complete in all respects. (NSI)

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. (DSR 15.56)

Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement: 3 fine sand) : Raised and cut pointing (DSR 13.31.2)

Providing and fixing G.I. tank nipple AVR make. Complete in all respect: 15 mm nominal bore (NSI)

20 mm nominal bore (NSI)

Providing and fixing C.P. Extension 1/2'' nipple size Complete in all respect (NSI)

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge (DSR No. 17.16 A).

Providing and Fixing Toilet paper holder: (DSR No. 17.34.1)

Providing and fixing PTMT towel rail complete with brackets fixed to woodencleats with CP brass screws with concealed fittings arrangement of approvedquality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms ( DSR. No. 17.73.1)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate etc (1.25)

Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length 15 mm nominal bore (DSR No. 18.21.2.1)

Providing and Fixing of laminated sign board material for indication of Sign board at toilet block complete in all respect as per the satisfaction of Engineer in charge: 48"X24" (NSI).

Credit against Old Sanitary Items (G.I. pipes) (NS)

Credit against old Electrical Items (NS)

Credit against old steel (NS)

Please Enable Macros to View BoQ information