REPAIRS TO AREA DRAINAGE INCLUDING COVERS, DESILTING , REPAIRS TO FLOORING, CEILING, SANITORY FITTING, ROOF, WALLS, CERTAIN BLDGS AND PERIODICAL SERVICES TO CERTAIN BLDGS AT 2U DET DIGLIPUR

Amount

Demolition of brickwork or stone/ boulder masonry or PCC block masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removal of debris to a distance exceeding 500 mtrs and depositing where directed.

M&L Pre-cast cement concrete Type C1, 1:3:6 (using 20mm graded crushed granite stone aggregate), block masonry with solid blocks with minimum compressive strength of 50 Kg/Sqcm, exceeding 10 cm in width and setting in cement mortar 1:6 complete.

Taking down cement plaster on brick or stone walls, concrete surfaces etc. including raking out joints, hacking for key, scrubbing down with water, etc. and removal of debris to a distance exceeding 500 mtrs and depositing where directed.

M&L for rendering 10mm thick in cement and sand mortar 1:6 on fair faces of brick work or concrete surfaces, finishing the surface even and smooth without using extra cement complete all as specified.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) and removal of debris to a distance exceeding 500 mtrs and depositing where directed.

M&L for 75 mm thick PCC Type D2, 1:4:8 (using 40 mm graded crushed granite stone aggregate) laid in sub-floors, sub-bases, floors and pavings, etc. finishing surfaces of concrete even and rough complete all as specified.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry on floors/ steps, over and including screed bed or bedding layer of 15 mm thick in CM 1:6 complete.

M&L PCC Type B1, 1:2:4 (using 20 mm graded granite stone aggregate) as in copings, kneelers, apex stones, bed plates, levelling course, kerbs water troughs and the like including use of formwork, weathering, slightly rounded or chamfered angles and throating.

M&L for PCC Type B2, 1:2:4 (using 40mm graded granite stone aggregate) as in surface channels and drains complete.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and facilitate to cut reinforcement and removal of debris to a distance exceeding 500 mtrs and depositing where directed.

M&L precast RCC Type B1, 1:2:4 (using 20 mm graded granite stone aggregate) as in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in CM 1:4, including necessary formwork complete. Note: Reinforcement shall be measured and paid separately.

M&L for high yield strength deformed TMT steel bars 10 mm dia and over as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc. (Inner girth only shall be measured).

Desilting of storm water drains including dewatering and removing soil/ muck to outside the MD land and depositing where directed.

M&L for rendering 15mm thick in cement and sand mortar 1:4 on fair faces of brick work or concrete surfaces, including mixed with WPC @ 3% by weight of cement content, finishing the surface fair and even complete all as specified.

Supply only Integral waterproofing compound.

M&L for preparing newly plastered surfaces of walls and applying two coats of cement based paint over a coat of white wash complete.

M&L preparing new plastered wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer including 3 mm thick white cement based wall care Birla putty complete all as directed.

M&L for preparing plastered or unplastered new surfaces of walls and applying three coats of white wash complete.

M&L for 40 mm thick PCC Type B1, 1:2:4 (using 20 mm graded crushed granite stone aggregate) laid in flooring and pavings, etc. finishing cement concrete surface even and fair without using extra cement complete all as specified.

M&L 75 mm thick PCC Type C2, 1:3:6 (using 40 mm graded crushed granite stone aggregate) laid in plinth protection, surface even and fair without using extra cement complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified.

M&L Non - skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of 15 mm thick for laying floor finishes, in cement and sand mortar 1:6 complete.

M&L Glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including rendering 10 mm thick in cement and sand mortar 1:4 complete.

M&L for vitrified ceramic tiles (first quality) 10 mm thick (square/ rectangular), light shade, polished, area of each tiles not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of 15mm thick for laying floor finishes, in cement and sand mortar 1:6 complete.

Dismantling framed work fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section.

S&F mild steel works hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and ountersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; conforming to Fe-290 Gde E-165

M&L preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified.

Dismantling asbestos cement / CGI (corrugated, semicorrugated, etc.) sheets in roof coverings.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ rain water gutter/ cladding to wall, fixed with self tapping screws as specified.

Supply, providing and fixing suspended false ceiling consisting of 12 mm thick Gypsum seamless board suspended on GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick two unequal flanges of 20 mm and 30 mm and web of 27 mm fixed to surrounding walls using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.90 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx. 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2 mtr length) of 0.55 mm thickness having curled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre fixed to roof slabs, boards are to be joined and finished so as to have a flush look which includes finishing the tapered and square edges of the gypsum board with joining compound paper tape and two coats pasting emulsion paint over one coat of primer and one layer putty 3 mm thick suitable for gypsum board. (As per the recommendations / practice) including necessary fittings.

Dismantling timber boarding, any description, fixed in any position with screws.

S&F vitreous China water closet (squatting pan), ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including provision of lime concrete bedding.

S&F in repairs vitreous China wash hand basin, white, flat back, size 580x450 mm excluding taps, waste pipe, chain and plug and porcelain stopper but including mild steel/ CI brackets and cutting for and pinning in ends of brackets or erecting stand complete all as specified.

S&F in repairs Pillar taps, cast copper alloy, chromium plated, fancy type, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore and fixed.

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe, including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, waste pipe.

S&F (in repairs) Vitreous China wash down water closet pan EWC (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) and plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, including connection to drain (or outgoing pipe) and to flushing pipe, etc.complete all as specified.

S&F (in repairs) 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle and flushing pipe including brackets specified complete all as specified.

S&F in repairs PVC connections 15mm size with PTMT nuts and washers of length 600mm.

S&F stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe 15mm bore dia or for unions and fixed.

S&F brass chromium plated shower roses 125mm size with or without swivel joints, any size, including fixing to steel pipe or union.

S&F in repairs bib taps, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule 15mm bore and fixed.

S&F new 500 litres capacity rotational moulded polythene water storage tank, (cylindrical vertical with close top) triple layer (ISI Marked) white colour both inside and outside with top cover including ball brass valve, high pressure, with polythene float and flynut complete, hoisted and fixed in position where ordered and making necessary connection and testing complete all as directed, including dismantling old water tank of capacity exceeding 250 ltrs but not exceeding 500 ltrs and removing to store complete all as specified.

S&F new 1000 litres capacity rotational moulded polythene water storage tank, (cylindrical vertical with close top) triple layer (ISI Marked) white colour both inside and outside with top cover including ball brass valve, high pressure, with polythene float and flynut complete, hoisted and fixed in position where ordered and making necessary connection and testing complete all as directed, including dismantling old water tank of capacity exceeding 500 ltrs but not exceeding 1000 ltrs and removing to store complete all as specified.

Taking down shutters of any description not exceeding 1 sq. m each from chowkats.

Taking down shutters of any description exceeding 1 sq. m but not exceeding 2 sq. m each from chowkats.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exceeding 1.50 Sqm each.

S&F 2nd class hardwood 30 mm thick Glazed and skeleton shutters, divided in to squares with plain, chamfered or rounded, mitred and rebated sash bars, any numbers and prepared to receive glass, gauze, etc. fitted with cut and mitered beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats.

S&F 2nd class hardwood 35 mm thick Glazed and skeleton shutters, divided in to squares with plain, chamfered or rounded, mitred and rebated sash bars, any numbers and prepared to receive glass, gauze, etc. fitted with cut and mitered beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats.

S&F 2nd class hardwood 35 mm thick plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F curtain rails anodised aluminium alloy with fixing brackets etc complete.

S&F 150 mm long extruded aluminium alloy handles, fabricated type, anodised.

S&F 100 mm long extruded aluminium alloy handles, fabricated type, anodised.

S&F 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed.

S&F 100 mm long aluminium anodised, barrel tower bolts of extruded section and fixed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

S&F 100 mm long butt hinges, medium weight, cold rolled mild steel, and fixed.

S&F 75 mm long butt hinges, medium weight, cold rolled mild steel, and fixed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples and including 2nd class hard wood beads straight (any size) for glazed or gauged joinery, renewed including mitered etc and painting exposed surfaces of beads with two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L for preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

S&F door closer hydraulically regulated, aluminium (die cast) body, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed.

M&L for preparing plastered or unplastered old decorated surfaces of walls and applying one coat of white wash complete.

M&L for preparing plastered or unplastered old decorated surfaces of ceiling and applying one coat of white wash complete.

M&L for preparing plastered or unplastered old decorated surfaces of walls and applying one coat of cement based paint complete.

M&L for washing, rubbing down and stopping of distempered and painted surfaces of walls and applying one coat of distemper oil emulsion paint complete.

M&L for preparing old painted wooden surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete.

M&L for preparing old painted steel surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete.

M&L for preparing old treated wooden surfaces and applying one coat of French polishing on surfaces of any description, width or girth including cleaning and preparing the surface.

M&L for complete removal of existing treatment on walls and applying two coats of distemper oil emulsion paint over a coat of alkali resistant priming paint complete.

M&L for preparation of old painted surfaces of any description over 10cm girth or width, not otherwise described and applying one coat of synthetic enamel (ordinary tint) paint on plastered surfaces, stone, brick, concrete surfaces etc.

M&L for preparing plastered or unplastered old decorated surfaces of walls and applying one coat of antifungal exterior emulsion weather proof paint complete.

M/s Mohammed Shamim

ANITA VARMA ENTERPRISES

S K ENTERPRISES

M/s K Moorthi