138WE/L-44/2022-23

Amount

Dismantling plain or corrugated steel sheeting any gauge thickness including nanital or similar pattern, complete all as specified and directed by Engr-in-charge.

S&F 0.63mm thick galvanised mild steel sheets with two corrugation side lap fixed with J or L hooks with grade of zinc coating 275, complete all as specified and directed by Engr-in-charge.

Detto as per Ser No 2.00 but fixing only.

S&F 0.63mm thick galvanised mild steel sheeting and in ridges hips, valley gutters etc conforming to class VIII.

S&F Pre-painted galvanum aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / clading to walls fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvanum aluminum zinc coating GI based plain steel sheet 0.50 mm of an colour having tensile strength of 550 Mpa as in roof covering / clading to walls, fixed with self tapping screws as specified.

Dismantling timber scantlings 40 Sqcm and over in section, in any position.

M&L Second class hard wood in scantlings all as specified and directed.

Dismantling structural steel work any description any position, complete all as specificed and directed by Engr-in-charge.

S&F steel work in tubular trusses including special shaped washer etc, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240.

S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and quides for sliding doors, fixed with angle cleats or other connecting plates, Fe 410, Gde E-250.

M&L for two coats of synthetic enamel paint on new galvanised corrugated steel surfaces including preparation of new zinc or galvanised surface to receive paint over a coat of red oxide and treatment with mordant solution.

M&L for two coats of synthetic enamel paint on new steel surfaces including preparation of over a coat of red oxide zinc chrome primer.

Detto as per ser No 13 but one coat on old decorated steel surfaces.

Dismantling wooden ballies of any description in any position except posts or struts etc.

S&F hard wood wooden ballies laid and fixed as directed by Engr-in-charge conforming to class III.

Demolition brick work / block masonry or stone / boulder masonry, built in built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles.

M&L for precast cement concrete block masonary type C-1, using crushed stone 20 mm graded aggregate, set and jointed in cement mortar 1:6.

M&L for walling of random rubble, uncoursed masonry, built in CM 1:6 all as specified.

Ditto all as item No 19 above but except stone.

M&L for raised pointing to random rubble stone masonary upto course in CM 1:4 all as specified.

Taking down cement plaster on brick or conc surfaces including racking out joints hacking for key, scrubbing down with water etc, complete all as specified and directed by Engr-in-charge.

M&L for 15 mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:4.

M&L for 15 mm thick rendering on fair faces of brick works in cement mortar 1:6 finished even and smooth without using extra cement.

M&L for two coats of cement base paint on newly plastered surfaces over a coat cement primer including preparation of surfaces.

Demolition of cement concrete (unreinforced) of any descriptions, in ground floors not exc, 15 cm thick, above or below ground level, complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D-2, using 40mm graded crushed stone aggregate as in sub base, complete all as specified and directed by Engr-in-charge.

M&L for coloured chequered cement concrete tiles, machine pressed, factory made of size 300 mm x 300 mm x 25 mm thick, set, jointed and pointed in neat cement slurry, with grey cement and no pigment, laid in floors, over and including 20 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-1, (using 20mm graded stone aggregate) as in plinth protection including making proper joints with bitumen mastic with sand as per specification at an interval of 3 m complete all as specified and as directed.

M&L Rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 500 ltrs, including dismantiling of water tanks and removed to store, complete all as specified.

M&L Rotational moulded polyethylene puf insulated water storage tank (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 500 ltrs, including dismantiling of water tanks and removed to store, complete all as specified.

Taking up or down steel tubing 20 mm bore including cleaning for refixing or removal to stone, complete all as specified.

Taking up or down steel tubing 25 mm to 32 mm bore including cleaning for refixing or removal to stone, complete all as specified.

S&F 20mm bore 3 layer PP-R Ploypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV Stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R Plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc, complete all as specified.

S&F 25mm bore 3 layer PP-R Ploypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV Stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R Plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc, complete all as specified.

S&F 32mm bore 3 layer PP-R Ploypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV Stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R Plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc, complete all as specified.

M&L for 15 mm bore medium grade galvanished iron water tubing with all fittings and fixed complete to walls or laid in trenches, complete all as specified.

Ditto all as per item No 37 above, but fixing only, complete all as specified.

M&L for 20 mm bore medium grade galvanished iron water tubing with all fittings and fixed complete to walls or laid in trenches, complete all as specified.

Ditto all as per item No 39 above, but fixing only, complete all as specified.

S&F PPR 25 mm bore Socket in new or old position.

S&F PPR 25 mm bore Tee in new or old position.

S&F PPR 25 mm bore Elbow / bend in new or old position.

S&F PPR 25 mm bore Uniun in new or old position.

S&F PPR 15/25 mm bore FT Socket in new or old position.

S&F PPR 15/25 mm bore Thread elbow in new or old position.

S&F PPR 25 mm bore Tank nipple in new or old position.

S&F in repairs PVC waste pipe 32 mm bore with cup and washers complete on new or old locations, complete all as specified.

S&F PVC connection 15mm bore with ptmt nuts of length 600mm, complete all as specified and directed by Engr-in-charge.

S&F in repair 15 mm bore bib taps fancy type chromium plated with capstan head chromium plated screwed down screwed for iron pipe or brass ferrule. (Min wt 350 Gms)

S&F in repair 15 mm bore pillar tap fancy type cast copper alloy with capstan head chromium plated screwed down under high pressure with or without lettered hot or cold with long shank and fly nuts screwed for iron pipe.

S&F in repairs 15 mm bore stop cock fancy type chromium plated cast copper alloy screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule.

S&F in repair 15 mm bore bib taps standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Min wt 90 Gms)

S&F in repair 15 mm bore PTMT pillar tap of any colour screwed for iron pipe and fixed. (Min wt 110 Gms)

S&F in repair 15 mm bore stop valve of PTMT any colour high pressure screwed for iron pipe and fixed.

Providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixing with dash fasteners of required dia and size including necessary filling up the gaps at junctions i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, CP brass / stainless steel screws, including taking down complete all as specified and directed by Engr-in-charge.

Taking down chowkhat or frames exc 1.50 Sqm n.exc 4 Sqm without taking down shutters from the frames.

Ditto-all as per item No 57 above, but n.exc 1.50 Sqm.

Taking down shutter of any description n exc 1 sq m each.

Taking down shutter of any description n exc 1.00 sqm but n exc 2.00 sqm.

Refixing shutters of any description exc 1.00 sqm and n.exc 2.00 sqm each in same opening , complete all as specified and directed by Engr-in-charge.

S&F second class soft wood as in plian solid straight chowkhats wrought framed rebated on the solid put together on with glue pinned at joints.

S&F 30 mm thick 2 nd class softwood, plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats.

S&F 30 mm thick flush shutters, solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed by Engr-in-charge.

S&F 30 mm thick 2nd class softwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I, Section 8, supplied and fitted to chowkats.

M&L for 30 mm thick 2nd class soft wood glazed and skelton shutters as in windows open rebated and prepared to receive glass gauge etc, divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers fitted with cut and mitered beads for securing glass gauge etc, sizes of members of shutters as specified in SSR Part-I, Section 8.

S&F 150 mm long aluminium anodised barrel tower bolt of extruded section in old or new position.

S&F 100 mm long aluminium anodised barrel tower bolt of extruded section in old or new position.

S&F aluminium door handle cast type 150 mm in old or new position.

S&F aluminium door handle cast type 100 mm in old or new position.

S&F 250 mm long aluminium door sliding door bolt incl all necessary fitting and bolts.

S&F 100 mm long mild steel medium weight but hinges cold rolled.

S&F MS butt hinges medium weight cold rolled 75 mm long.

S&F 375 mm, mild steel ordinary rat tail rod pattern springs including roller plate in repair, complete all as specified.

Hacking out old broken glasses (Any thickness, size quality, description) from wooden or steel frames fixed with putty or wooden beads.

S&F 4.8 mm thick sheet glass ordinary quality in any position and glazing with oil putty, glazing clips / beading as per site requirement n exc 0.5 sqm in each pane.

S&F 4.8 mm thick sheet glass ordinary quality in any position and glazing with oil putty, glazing clips / beading as per site requirement exc 0.5 sqm in each pane.

S&F 3 mm thick glass sheet oridinary qlty in steel or wooden frames complete with fixing materials such as putty glazing pins wooden beads etc.

S&F in repair galvanished mild steel wire cloth 56 mm nominal dia of wire and average width of apperature 1.18 mm and fixed with tinted tacks, or galvanised wire staples.

S&F anodised aluminium frames for door, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified.

S&F anodised aluminium door shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleat, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws etc, complete all as specified.

S&F anodised aluminium windows and ventilator shutters, side hung type without sash, aluminium section weighing 0.55 Kg/m including necessary joining cleat, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150 mm long (1 Nos) hinges type B-21 100 mm long (2 Nos) suitable handle (1 Nos) etc, complete all as specified.

M&L for two coats of synthetic enamelled paint on new decorated wooden surfaces including preparation.

M&L double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, complete all as specified and as directed.

S&F in repair aluminium door closer (aluminium extruded section) hydraullically regulated, designation No 3, universal type, suitable for door shutters of 851 mm to 1000 in width and of weight 61 to 80 Kg.

S&F brass mortice lock four levers (Harrisons) vertical type size 100 mm or above in old or new position as directed by Engr-in-charge.

S&F Harrison rails, anodised aluminium alloy, with fixing brackets, stops, rollers in repair etc complete all as specified.

S&F floor door stopper 150 mm long of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, complete all as specified and as directed.

Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) any thickness including covered fillets and supporting members.

Dismantling boarding, any description, fixed in any position with nails.

Dismantling timber scantlings 40 Sqcm in section in any position (Frames section).

M&L for 2nd class softwood clean sawn as in scantling fixed with nails exceeding 13 sqcm and n exc 25 sqcm in section.

S&F, Gypsum ceiling board 8 to 9 mm thick in 600 x 600 mm pannel, ceiling tiles are laminated with white colour PVC film on the face side and a metalised polyster film on the back side. Conforming to IS -14862 type B category three incl GI frame, grid work, Hold fast, suspended with GI wire complete.

M&L for wooden floor tiles 7 mm thick with dove tailed joints laid over 150 micron polythene film and 3 mm thick foam as per manufacturer's instructions and fixed with decorative wooden beadings as per site requirement complete all as specified and directed. Make and shade of tiles be all as approved.

M&L for 9 mm thick prelaminated particle board interior grade, prelaminated one side with decorated choice lamination and other side balancing white fixed with screws/ nails to timber frame work as in wall pannelling, complete all as specified.

M&L for 9 mm thick prelaminated particle board interior grade, prelaminated one side with decorated choice lamination and other side balancing white fixed with screws/ nails to timber frame work as in ceiling, complete all as specified.

M&L for 6 mm thick 5 no of ply wood BWR, type BB as in ceiling / boarding fixed with screws to timber frame work.

M/S SHAMSHER ALI SUFI

Horizon Construction Company

M/S BALI CONSTRUCTIONS

PADMA ENTERPRISES

M/S LEO TRADERS

M/S Praveen Kumar and Sons

R B TRADERS

Mehar Enterprises

SONAM ANGCHOK

ASHOK KUMAR SHARMA