PROVN OF HARD STANDING FOR DRILL NURSERY AT CTW

Amount

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft / loose soil complete all as specified and direcred.

Excavating over areas, not exceeding 1.5m deep & getting out in soft / loose soil complete all as specified and direcred.

Rolling and consolidating formation surfaces in cutting with 8 to 10 Ton rollers complete all as specified and direcred.

M&L for 150mm thick (compacted thicknesss) WBM/WMM, in two layers with stone coarse aggregates of grading 2 (63 to 40mm size) or of grading 3 (50mm to 20mm size), spread, rolled and consolidated to gradient and camber required complete all as specified and direcred.

M&L for PCC M-20 Design Mix using 20 mm graded stone aggregate, laying by means of RMC in pavement / hard-standing with mechanical paver and maintain the proper gradiant and finishing surface of concrete by brooming complete all as specified and directed.

M&L Applying two coats of Plastic emulsion paint on brick, stone, concrete, asbestos cement or plaster surface of any description over 10cm girth or width, not otherwise described including preparation of new surface & priming paints plaster coat complete all as specified and direcred.

M&L for forming constructin (Dummy) joints 65 mm deep x 10 mm wide , filled with sealing compound Grade 'A' complete all as specified and direcred.

Excavating in trenches, not exceeding 1.5m wide & not exceeding 1.5m in depth; for foundation etc., or for shafts, wells, cesspits, manholes, pier holes, etc., not exceeding 10sq m on plan & getting out in soft/loose soil complete all as specified and direcred.

M&L brick work with Fly Ash bricks (old size bricks) straight or curved on plan exceeding 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L Rendering 15mm thick on brick masonry surfaces on fair faces or surface other than fair face of brickwork in CM (1:4) finished even & smooth (without using extra cement) complete all as specified and direcred.

M&L Plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in coping including necessary form work copmplete all as specified and directed.

M&L PCC in foundations, filling and mass-concrete type C2 (1:3:6) using 40 mm graded stone aggregate complete all as specified and direcred.

S&F post and strut in fencing including cutting tops to shape as directed drilling holes notching for wire flat iron fillet ( for securing wire mesh) in including all necessary drilling bolting and rivetting conforming to Fe-290 Gd-165 complete all as specified and direcred.

S & F chain link MS galvnised fencing (dameter of wire 4mm each with nominal pitch 100mm) etc., complete all as specified and directed. Note: Binding wire, rails, straining bolts etc., shall be measured and paid seperately under relevant item of this BOQ.

M&L for round bars 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping, hooking ends and binding with and including mild steel wire ( annelaed) not less than 0.9 mmd ia or securing with clips. Fe-410-W (Gde.E-250) complete all as specified and direcred.

S&F mild steel screw bolt (maching made) with hexagonal or square head at one end and screwed the other with washer not exceeding 5 cm long dia bolt 5 to 10mm complete all as specified and direcred.

S&F framed work as in door or gates of angle or other section with gusset plates, rails, braces etc., complete, drilled for fixing of steel sheeting or other covering doors etc., to be prepared for hanging or sliding with and including either hooks and hingers or steel hanging door fitting (Exclusive of steel sheeting or other overeing running rails and guides) and hanging also faterning and fixing complete all as specified and direcred.

M&L for two coats of synthetic enamel paint on new surface of steel and iron surfaces any description over 10 cm width or girth over a coat of red oxide primer including prepration of surface complete all as specified and direcred.

Returning, filling in soils, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and direcred.

Removing of surplus excavated material/ soil not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m aove the starting point complete all as specified and direcred.

M&L brick work with Fly Ash bricks (old size bricks) straight or curved on plan exceeding 6m mean radius built in CM 1:4 complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in sub base complete all as directed

M&L for hard core of gauge exceeding 63mm but not exceeding 100mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rolled/rammed to a true surface complete all as directed.

M&L for 25 mm thick PCC (1:2:4) type B0 using 12.5mm graded stone aggregates as in finishing of concrete all as directed by Engr-in-Charge.

KOGANTI CONSTRUCTION COMPANY

SAI RUPA CONSTRUCTIONS

M/s GM Constructions