PROVN OF TOILET BLOCK FOR ARTY REGT AT SKAMPUK, TOILET BLOCK AT 16 MOB FD VET HOSP ,PROVN OF TOILET BLOCK AT ROCKFALL AND SPL REPAIR TO BLDG NO T-297, T-317 AND T-314 AT SUP PT POST-9 UNDER GE 873 EWS

Amount

Dismantling of plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed by Engr-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified.

S&F 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 fixed with L-type or J-type or cranked hook bolts in lieu of screws complete all as specified and directed by the Engineer–in–Charge.

S&F Fe-410-W (Gde-E-250) quality A Roof trusses (framed), trussed, purlin, crane gantries, rails and fastenings and heavy brackets framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc complete all as specified and directed by the Engr-in-charge.

Re- fixing excpt sheeting any thickness 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 fixed with L-type or J-type or cranked hook bolts in lieu of screws complete all as specified and directed by the Engineer–in–Charge.

S&F 0.63mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275

M&L Preparatoion of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces, complete all as specifeid and directed by engr-in-charge

M&L for preperation of existing treatment on steel / CGI sheets of any descripton and applying one coat of synthetic enamal paint (galvanisation should be removed if required) ,complete all as specified and as directed.

Demolition for Brickwork or stone/boulder masonry, built in Cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

Taking down cement plaster of any description on brick or stone walls, etc, incl racking out joints, hacking for key, scrubbing down with water etc, complete all as specifeid and directed by engr-in-charge.

Precast cement concrete block masonry with solid blocks , type C1 1:3:6 (using 20 mm graded aggregate) .exc 10 cm in width and set in cement mortar 1:6 complete all as specified.

M&L precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) setting in mortar, Type C-1 1:3:6 and 20mm graded Set in Cement Mortar 1:4 complete all as specified and directed by the Engineer–in–Charge.

M&L, for prepartion of newly plastered wall surfaces of any description applying Two coat of cement base paint, over a coat of primer complete all as specifeid and direct.

M&L, Rendering 15mm thick on fair faces of brick work finished even and fair in CM 1:4, complete all as specifeid and directed by engr-in-charge.

M&L, Rendering 10mm thick on fair faces of brick work finished even and smooth without using extra cement in CM 1:6, complete all as specifeid and directed by engr-in-charge.

M&L, Rendering 5mm thick on fair faces of brick work finished even and smooth without using extra cement in CM 1:4, complete all as specifeid and directed by engr-in-charge.

M&L preparing new surface,plastered or un plastered walls and applying two coat of cement bas paints over a one coat of white wash all as specified and directed

M&L preparing new surface,plastered or un plastered walls and applying two coat of oil bound distember over a coat of primer all as specified and directed

M&L preparing new surface,plastered or un plastered walls and applying three coat of white wash on ceiling all as specified and directed

Rendering 15 mm thick over over RCC slab to be finished even and smooth (wirhout using extra cement ) in CM 1:3 with liquid water proofing admixture all as specified ( Liquid water proofing admixture shell paid seperately)

M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface with broken stone or Boulder all as specified and directed.

M&L 100mm PCC type D- 2, 1:4:8 (20mm graded aggregate) as in flooring 100 mm thick complete all as specified

M&L Screed bed or bedding layer of mortar 15 mm thick for CM 1:6 laying floor finishes complete all as specified

M&L coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified

M&L non skid ceramic tile 7 to 8 mm thick (square/rectangular) are of each tile exc 0.11 Sqm but not exc 0.18Sqm , in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick CM 1:4 screed bed for laying floor all as specified and directed.

M&L for white glazed ceramic tiles in vertical surface 300X200X7 mm thick set and jointed in neat cement slurry over 10 mm thick rendering in CM 1:3 and pointed in white to match complete.

M&L Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified

S&F of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame a site as per specification & drawing

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed, complete all as specified and directed.

S&F 35mm 2nd class HW Plain framed, panelled shutter (two panel) withclock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle boardwith commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned andvchemically pressure treated, complete all as specified and directed.

S&F 25mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (b); supplied and fitted to chowkat, complete all as specified and directed.

S&F 32 mm Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm-45gms/40mm-60 gms, complete all as specified and directed.

S&F chromium plated 15mm Bib taps, cast copper alloy wit crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F vitreous china wash down water closet pan (pedestal pattern) white with trap including connection to existing out joint pipe, flushing pipe or cistern, antisyphonage pipe, including making good to floor,plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device etc complete Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position all as specified and directed.

S&F PVC (SWR) 'P’ & S trap 110mm bore, complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks 1000 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position including making necessary arrangement for fixing inlets , outlets and over flow pipe and provision of wash out pipe etc including taking down of existing tank, complete all as specified and directed.

S&F 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s, complete all as specified and directed.

M&L Liquid water proofing compound complete all as specified and directed by the Engineer–in–Charge.

S&F 30cm long hold fast conforming to FE 290 gde E-165 of section 25x6 mm

M&L Salt-glazed stoneware gully traps, square or round mouthed, tvpe 150x150mm with all exacavation and earthwork ,complete bed ,sourrounds , kerbs etc and cast iron grating including &jopibning through drain pipe in CM 1:2 all as specified

S&F 25 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete

Providing cement concrete type C-1, 1:3:6 ( using 20mm graded stone aggregate), 50 mm thick as in plinth protection laid in bays not exceeding 2 Sqm each and finishing even and fair on top without using extra cement with 6mm wide joints throughout the thickness of plinth protection in concrete bays and in between the walling and plinth protection.

S&F PVC (SWR) bends 75mm complete all as specified and directed by the Engineer–in–Charge.

S&F PVC (SWR) bends 110mm complete all as specified and directed by the Engineer–in–Charge.

Dismantling wall and ceiling board (fibre, pulp, insulation etc) or insulation board/slabs/ blanket any thickness including cover filllets.

M&L 9mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work as in ceiling incl taking down & refixing all electric fittings, fixture and wiring complete all as specified

M&L, for prepartion of old surfaces of wood or wood based materials (dusting and cleaning only) and applying one coat of synthetic enemal paint on surface of any desciption over 10 cm width or girth or not otherwise, complete all as specifeid.

Dismantling timber framed in fillets,rails, posts rafters,purlines, etc under 40 sq cm in section

M&L second class Hardwood plain filllets, rectangular in section, clean swan, secured with nails exc 13 and n.exc 25 Sqcm.

M & L for 12mm width teak wood lipping 6 mm thick for Patical board/block board complete fix with nail.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness ( below or above gd level).Complete all as specified and directed.

M&L for 25mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) complete all as specified and directed by the Engineer–in–Charge.

M&L for light shade Vitrified Ceramic tiles 10 mm thick (square/rectangular),polished, area of each tiles not exceeding 0.36 sqm in floors over 15 mm thick screed bed of CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete.

M & L for Providing, cement concrete 1:2:4 type B-1(20 mm graded stone agg) in roof kerbs or mud stops, rounded or chamfered on edges, in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, kerbs , and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

Dismantling of water tanks 500 litres capacity of any description and removing to store complete all as specified and directed.

Taking down 15/16 mm water supply tubing of any description and connections including cleaning for re-fixing or removal to store etc complete all as specified.

Taking down 20 mm water supply tubing of any description and connections including cleaning for re fixing or removal to store etc complete all as specified.

Hacking out old broken glass (any thickness, size quality or description from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frames including with shutters ( without taking of shutters from the frames) exc 1.5 sqm n exc 4 sqm each complete all as specified.

Taking down chowkhat or frames including with shutters ( without taking of shutters from the frames) exc 1.5 sqm each complete all as specified and directed by Engineer-in-Charge.

S&F mild steel work as in hold fasts and similar work confirming to Fe-290 or Gd -E 165 complete.all as specified and as directed by the Engr-in-Chage

S&F 2nd class soft wood 35 mm thick Glazed and skelton shutter, open and prapared to receive the glass, gauze etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc. (Glass / Wiremesh should be measured seperately) complete all as specified and as directed by the Engr-in-Charge.

M&L for Chequered cement concrete tile 20cmx20cmx25mm thick ,set and jointed over 20 mm screed bed in CM 1:4 and pointed in neat cement slurry in floor with grey pigment cement and pigment complete all as specified and directed by the Engineer–in–Charge.

S&F puff water tank 500 litres capacity, insulated cylindrical vertical type double layer duly filled with glass wool with closed top hoisted and to resist in temprature -30 degree to +35 degree celcius fixed in position with all fittings over PCC platform complete all as specified and directed.

S&F 25 mm 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16)UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded poly-propyl-ene random fittings fixed complete to walls, ceilings or in floors etc.

S&F 20mm outer dia 3-layer PP-R poly-propylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stavlized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceiling or floors etc. complete all as specified and directed.

S&F 15/16mm outer dia 3-layer PP-R poly-propylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stavlized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceiling or floors etc. complete all as specified and directed.

S&F for 40 mm thick Flush shutters, solid core construction ,with block board core and plywood face panels commercial type on both sides , S&Fed to chowkats , complete all as directed by Engr-in-charge.

S&F in repairs vitreous china water closet sqatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests (excuding flushing cistern and flush pipe) incl making good complete all as specified and directed

S&F in repair vitreous china wash basin, white, flat back, size 550 x 400mm, including brackets & incl 32mm bore waste fitting brass, CP for glazed ware basin etc with long screwed shanks and fly-nuts flange end bedded in red lead cement and other end fixed including pedastal for washbasin complete all as specified.

S&F in repairs 10 litres capacity PVC valveless syphonic action type low level flushing cistern white with inlet, ball valve, float and handle including brackets, flush pipe etc complete all as specified.

S&F in repiar Vitreous China urinals size 465 x 355 x 265 mm white (minimum),bowl type (back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, flush pipe, grating and Union for discharge pipe alongwith fixing of 32 mm dia coupling complete

RCC M30 (20mm graded stone agg) in foundation, including rafts, footings, foundation beams, plinth bases for columns etc basement slabs under reamed piles and mass concrete, complete all as specified and directed.

RCC M30 (20mm graded agg) Columns, pillars,piers, post and struts, complete all as specified and directed.

RCC M30 (20mm graded agg) Beams cantilevers, bressummers, lintels over 1.5m span, complete all as specified and directed.

RCC M30 (20mm graded agg) Slabs supported on walls, beams and columns in floors, roofs landings, balconies, canopies, deck slabs and in shelves, complete all as specified and directed.

Use and waste of Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc, vertical or to batter complete all as specified and directed by the Engineer–in–Charge.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, flat, rough finished surface of concrete complete all as specified and directed.

Use & waste of Formwork, rough finished flat concrete Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.complete all as specified.

Use & waste of Formwork, rough finished flat concrete Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified

Use & waste of Formwork,rough finished Square,, rectangular or polygonal Formwork to sides of pillars, post, struts, piers, columns and stanchions complete all as specified.

M&L cement concrete type B-2, 1:2:4 (20mm graded aggregate) as in flooring 100mm thick complete all as specifed and directed by Engineer-in-charge

S&F wash down clloset (Pedestal pattern) pan and trap, inclduing connection to drain and to flushing pipe, antisyphonage pipe, etc flush pipe of sixe 630x450mm to squatt pattern closet including all joints and making good to the floor complete all as specifed and directed by Engineer-in-charge

Mild steel TMT bars 10mm rounded dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified

All as per Srl Item No.85 above but 6mm to 8mm dia. 5mm dia and over up to and including 10mm dia in stirrups complete all specified.

All as per Srl Item No.85 above but 5mm dia and over up to and including 10mm dia in stirrups complete all specified.

S&F 32mm bore waste pipe for WHB complete all as specified & directed

S&F in repairs pillar taps cast copper alloy 15mm bore with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15mm Stop valves, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for uniuns and fixed complete all as specified and directed.

S&F in repairs PVC Connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

M&L in repair PVC(SWR) floor trap plain with gratings including jointing to waste pipes with solvent cement size 75mm bore complete all as specified and directed.

S&F in repairs aluminium anodised tubular towel rail, 20mm dia ‘D’ type, 60CM long between flanges complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints, jointed with solvent fixed to walls complete all as specified.

S&F in repair 110mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints, jointed with solvent fixed to walls complete all as specified.

S&F Soap dish fixed to walls with chromium plated brass screws complete all as specified.

S&F 150 mm aluminium alloy, anodised ,sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet , cast or extruded section and fixing bolts and slidingbolt of extruded section or cast-aluminum alloy and fixed .

M&L for preparation of new untreated wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and painting with two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr-in-charge.

S&F 250mm aluminium alloy, anodised ,sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet , cast or extruded section and fixing bolts and sliding bolt of extruded section or cast-aluminum alloy and fixed

S&F stainless steel butt hinges, medium weight cold rolled 100mm size complete all as specified and as directed.

S&F stainless steel butt hinges, medium weight cold rolled 75mm size complete all as specified and as directed.

S&Fing 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer–in–Charge.

S & F for SGSW bend of 150mm dia complete all as directed.

S& F 100mm dia cast iron soil, sand cast pipe waste and vent pipes in any length as specified.

Plain cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in bed to drain pipes incl packing under and haunching against the side of pipes after they are laid and tested for 150mm bore SGSW pipes complete. Note- Thickness of concrete bed shall be 100mm.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

Constr of soakage well (3.00 mtr diax4.50 mtr deep) incl excavation in hard/dence soil, PCC 1:3:6 type C2, (using 40mm graded crushed stone aggregate) in foundation, hone combed and solid stone work in cement mortar 1:4, RCC cover slab, filling all as specified and shown in drawings (CESZ/TD-1078/2011 sh No 1/1 dt 01 Dec 2011)

S&Fing 100 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer–in–Charge.

S&F 100mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

Excavating over areas, n exc 1.5 m deep and getting out in hard & dense soil all as specified

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out hard/dense soil

M&L for 100mm thick hard core of gauge n exc 63mm, depositing where directed at a level n exc 1.5m above the starting point.

M&L for 100 mm thick PCC 1:4:8 type D2 (40mm graded agggregate as in sub base course complete all as specifed and directed by Engineer-in-charge

S&F grating doom 100mm dia of PTMT (minimum weight 25 gms) complete all as specifed and directed by Engineer-in-charge

S&F sheet glass 3.00mm thick figured glass pin headed type and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified and as directed.

S&F sheet glass 3.00mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified and as directed.

M&L Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dence soil complete all as specified.

M&L Returning, filling in incl spreading, levelling watering and well remming in layers n.exc 25cm width, Complete all as specified and directed.

M&L for Removing excavated materialn. exc 50m and depositing where directed at a level n exc. 1.5m above the starting point.

Sand cushioning for under ground cable 8 cm before laying the cable and 15 cm after laying and streching the cable complete all as specified and directed.

M&L Un-reinforced precast factory made concreate cable covers, class LV type-I with flat size 250x150x40 mm complete all as specified and directed.

M&L for Cement concrete Type D-2, 1:4:8 mix using 40mm graded stone aggregae as in foundation fillings, mass concrete complete all as specified and directed.

Taking down of MCB DB/TPNany type including MCB SP/SPN and making good of wall complete all as specified and directed by the Engineer–in–Charge.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as perconditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed by the Engineer–in–Charge.

Supply, layng, fixing, passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 10 Sqmm 2 core nominal cross complete all as specified and directed. Note:- Cable insulation should be withstand upto-35 degree temparature.

M&L Point wiring with 1.5 Sqmm (nominal area) copper conductor FRLS cable (multi-stranded) PVC insulated and unsheathed electric cable 1100 volts drawn through PVC casing and caping of suitable size (as per conductor run) with all fittings and accessories and including PVC insulated unsheathed electric cable 1100 volts 1.5 Sqmm (multi-stranded) copper conductor single core (green colour) as continuous earth wire connected to common earth dolly including 50mm deep box made out of plastic board of suitable size and shape and other boxes for mounting light fittings etc covered with 3mm thick plastic laminated Hylum ISI marked for following complete all as specified and directed by Engineer-in-charge.

One light point controlled by one 5 Amps one way switch

One 3 pin socket outlet 5 Amps on Same board

One 3 pin socket outlet 5 Amps on independent board

M&L point wiring for power point with 4.0 sqmm (nominal area) copper conductor FRLS cable ( multi-stranded) PVC insulated and unsheathed cable conductor 1100 Volts drawn through PVC casing capping of suitable size(as per conductor run) with all fittings and accessories and including PVC insulated unsheathed electric cable 1100 volts 2.5 Sqmm (multi-stranded) copper conductor single core (green colour) as continuous earth wire connected to common earth dolly including 50mm deep box made out of plastic board of suitable size and shape and other boxes for mounting light fittings etc covered with 3mm thick plastic laminated Hylum ISI marked for following complete all as specified and directed by Engr-in-Charge.

S&F Switch piano flush button single pole one way 5 Amps, 240 Volts complete all as specfied and directed.

S&F socket outlet 2–in–1, 3pin, 5A/6A (multipurpose) suitable for 2 pin/3 pin plug flush type complete all as specified and directed by the Engineer–in–Charge

S&F switch socket combination 2–in–1, 3pin, 6A (multipurpose) suitable for 3 pin/5 pin plug flush type complete all as specified and directed by the Engineer–in–Charge

S&F switch socket combination 2–in–1, 3 pin, 5/15 Amps, flush type (multipurpose) complete all as specified and directed by the Engineer–in–Charge

S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by the Engineer–in–Charge.

S&F Rechargeable LED Bulb 9 W ,220 V, white color all as specified and as directed.

S&F surface and wall mounted LED batten with polycarbonate housing and integrated electronic driver tube light fitting 22W, 4 ft long, 220 Volts , and connecting to ceiling rose with three core twisted flexible copper cable of suitable size complete all as specified and directed.

S&F Ceiling rose surface backelite ISI marked with 3 terminal including connecting and testing complete all as specified and directed.

S&F MCB DB sheet enclosure,Double door type, single pole and neutral 240V with 200 Amp rated bus bar suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete confirming to IP 42/43 without MCB and with enclosure blank plates for unused way suitable for 8 way complete all as specified and directed.

S&F MCB DB sheet enclosure,Double door type, single pole and neutral 240V with 200 Amp rated bus bar suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete confirming to IP 42/43 without MCB and with enclosure blank plates for unused way suitable for 12 way complete all as specified and directed.

S&F 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning all as specified and directed.

S&F MCB SPN 240V, 10KA 'B' curve (40-63) Amp current carrying capacity in the MCB DB complete with connection testing and commissioning all as specified and directed.

S&F LED light fitting 1X10W bulkhead luminaires including LED light and driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6mm thick burried directly in ground not less than 2.25m deep below normal ground level (with the top edge of the plate not less than 1.50 m below the normal ground level) connected to GI earth wire 4 mm by means of GI bolts, nuts, check nuts and washers of GI all as shown in electrical plate No.3 of SSR Part-I connected to earthing test point with and including necessary excavation and earth work in any strata PCC pit 1:3:6 type C-1, 20mm bore medium grade GI pipe for watering 15mm bore light grade pipe for GI wire protection and funnel including 40mm thick RCC slab cover and testing on completion all as specified and as directed.

M&L for GI Pipe (medium grade,ISI Marked) 32 mm dia ,1.5 mtr long ,bend to shape for street light fitting bracket ,with 2x pairs of MS clamps of suitable length of size 40x5 mm of MS flat iron with nuts bolts and washer complete all as Specified and directed.

S&F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete making all necessary connection with suitable capacity of 3 core circular cable complete all as specified and directed.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-charge.

S&F surface and wall mounted LED batten with polycarbonate housing and integrated electronic driver tube light fitting 20W, 4 ft long, 220 Volts , and connecting to ceiling rose with three core twisted flexible copper cable of suitable size complete all as specified and directed by Engineer-in-charge.

S&F MCB SPN 32 Amps 'C' series 240V 50Hz 10 KA suitable for lighting and other domestic loads complete including taking down all as specified and directed.

M&L for sheet metal enclosure for DBs when MCBs to be used TPN, 6 way double door with 200 amps bus bar all as specified.

M&L for MCB isolator, SPN, 2 pole, 240 volts, 40 amp, 10 KA, 'B' curve all as specified and directed.

S&F exhaust fan 450 mm sweep steel body AC single phase heavy duty all as directed and specified.

S&F of electrical water heating system/Hamam of capacity 300 Ltrs with Diesel/kerosene burner of 5 inch boiler and Diesel/kerosene Tank inner sheet made of 10 SWG mild steel sheet and outer sheet shall be made of 16 SWG of mild sheet. Glass wool insulation of 25mm thickness to be provided between outer and inner sheet. 100 mm dia MS pipes is to be fitted in centre which will act as heater. One direct water connection for inlet of water. Funnel for pouring water manually to be provided. One overflow pipe, 3 outlet of hot water from the boiler to be provided Inner chamber is to be painted with boiler paint and external steel surface are to be painted with two coats of synthetic enamel paint over a coat of red oxide incl necessary components like stand for hamam, Stand for fuel tank and fuel pipe for connecting burner, diesel/kerosene tank etc, complete all as specified and directed.

Deduct Schedule of Credit as listed in Schedule 'A' Part-II. Contract Sum shall be arrived after deducting the credit amount.

M/S MOHD KARIM (BID ID -3455736)

osho traders (BID ID -3455957)