SPECIAL REPAIR TO BLDG NO P-301, P-302, P-304, P-305 AND P-306 OF KV NO.1 AT BATHINDA MIL STN

Amount

Material and labour coloured double charged vitrified tiles, premium quality 10 mm thick (square/ rectangular) polished, size of tile not less than 600x 600x10mm thick, on 15mm thick screed bed in CM 1:6 in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and directed. (Colour/shade/pattern of tiles to be approved by GE)

All as per Ser item No 1 above, coloured with designer/ highlighter tiles pattern of tiles as approved by GE on vertical surfaces as in skirtings etc on 10mm thick back coat in CM 1:4, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour Non skid ceramic tiles, colored, of size not less than 400x400x7mm thick or of size as approved as in floors set and jointed in neat cement slurry and pointed in white cement with pigments to match over and including the provision of 10 mm thick bedding layer in cm 1:6 all as specified and directed.

Material and labour Glazed ceramic colored tiles of size not less than 300x450x6mm thick or of size approved in dado, set and jointed in neat cement on and including the provision of 10mm thick rendering in CM 1:4 all as specified and directed.

Material and labour pre-polished Kota stone 18-20 mm thick of suitable size as in flooring / landing of stair case over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab complete all as specified and directed.

Material and labour pre-polished Kota stone 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab complete all as specified and directed. Note:- Sigle piece of existing size of tread and riser of Kota stone shall be provided at site.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling stone slabs,Granite stone of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including backing coat of 10 mm in cement mortar 1:4 including moulding edges of granite complete all as specified.

Carefully Chipping, removing existing loose/damaged concrete with plaster from Roof, Chajja, Fascia, Fins, Drops and similar items by low impact high frequency hammer/chipper without damaging the existing sound concert and exposing old reinforcement upto 10mm beyond corroded reinforcement bars using electrically operated diamond concrete saw blade, making the edges straight and even and cleaning it by wire brush and then by air blower complete all as specified and as directed by Engr-in-charge.

Cleaning of existing reinforcement bars in Roof, Chajja, Fascia, Fins, Drops and similar items with wire brush/rotary wire brush to make entire circumference surface of bars free from rust scales, loose material, dirt etc, complete and providing, applying two coats of alkaline rust converting primer on the existing rebar and allowing it to react with rust for 6 hrs and form a corroson resistant, insoluble and adherant protective layer, including cleaning the reinforcement, wire brushing to remove the rust spalls, with time interval of 1 hour between the coats.

Providing and application of zinc rich epoxy anti-corrosive protective coating for reinforcement bars as corrosion protection system in 2 coats (of 0.4 kg/sqm approx) to the entire circumference surface of bars in Roof, Chajja, Fascia, Fins, Drops and similar items complete all as specified and directed. The product should confirm carbonation resistance of 2mm and bond strength > 1N/Sqmm according to ASTM C 882-78 incl all required scaffolding/ladders complete all as specified.

Apply SBR based bonding agent to the entire concrete surface prior to building up of concrete with Polymer modified mortar or any other treatment, incl cleaning the surface to remove dirt, dust or any other impurities on the surface, etc complete in Roof, Chajja, Fascia, Fins, Drops and similar item

Rebuilding the section of damaged RCC elements to its original size or as per thickness in layer of 10 mm each by providing and applying with pre-batched, one component fiber reinforced cementitious repair mortar having compressive strength >= 50 N/mm2 (28 days) according to ASTM C 109: Flexural strength >= 5N/mm2 (7 days) according to ASTM C 293-79, incl all required scaffolding/ladders complete all as specified.

Rebuilding the section of damaged RCC elements to its original size or as per thickness in additional layer of 10 mm each by providing and applying with pre-batched, one component fiber reinforced cementitious repair mortar having compressive strength >= 50 N/mm2 (28 days) according to ASTM C 109: Flexural strength >= 5N/mm2 (7 days) according to ASTM C 293-79, incl all required scaffolding/ladders complete all as specified.

Note:- All Structural repair work shall be carried out by the Authorised Applicator of the Material Manufacturer and applicator will be approved by GE before execution of work. .

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6, surface finished fair and even. complete all as specified and as directed.

M&L for rendering 15 mm thick (in two layers of 10mm in first layer and 5 mm in second layer) on fair faces of brick work or concrete surfaces in cement mortar 1:4, surface finished fair and even. complete all as specified and as directed.

M&L for rendering 10 mm thick on on ceiling in cement mortar 1:3, surface finished fair and even. complete all as specified and as directed.

Taking down cement plaster on brick work or concrete surfaces etc including raking out joints or hacking for key, scrubbing down with water etc.

Preparation of new plastered or unplastered surfaces of walls, applying 3mm thick wall care putty on wall (in two layers each of 1.5 mm thick) and two coats of acrylic emulsion distemper over one coat of priming plastered surfaces complete all as specified and as directed.

M&L for Preparation of newly plastered surfaces of walls and applying two coats of weather emulsion paint @ 1.43 Ltrs per X Sqm over a priming coat of exterior primer complete all as specified.

M&L for preparing new surfaces of ceiling and applying Three coats of white wash etc complete all as all as specified and as directed.

Preparation of old plastered or unplastered old decorated surfaces of ceiling by brooming for down or steel wire brushing, scrapping down make spots, trating oily/greasy spots, mass and efflorescence and applying one coat of white wash on ceiling including cornices etc complete all as specified and directed.

M&L for Preparing newly plastered surfaces of walls and applying three coats of White washing on Walls.

Preparing of plastered or unplastered old decorated surfaces of walls by brooming down or steel wire brushing, scraping down smoke soot, moulds, mass and efflorescent, salt and trading oil and greasy spouts and applying one coat of white wash on walls including cornices etc complete all as specified and directed.

Preparation of old plastered or unplastered old decorated surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, mass and efflorescent salts and trading oil and greasy spouts and applying two coats of acrylic emulsion paint @ 1.43 Ltrs per X Sqm over a priming coat of exterior primer complete all as specified.

Note for Periodical Items:- After every coat, stage passing will be got approved by the rep of accepting officer and will be kept on record. 5 year unconditional guranteee will be given by contractor through manufacturer as described in PS clause of tender documents. .

Taking down chowkhats or frame with shutter (without taking off shutters from the frames) not exceeding 1.5 Sqm each and removal from site complete all as specified and as directed.

S&F Powder coated Anodised aluminium frame (minimum thckness of powder coating 50 microns) for doors, windows with one or more rebates including joining cleat for fixing etc. complete all as specified.

BLANK

S&F powder coated aluminium window and ventilator shutters (sash and wire gauge shutter), top hung/ side hung type aluminium sections weighting 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws, powder coated aluminium fittings such as hinge type B-21 100 mm (2Nos) , stay (1No) for side hung shutter and 2 spring latches for top hung shutters each complete all as specified.

BLANK

S& F Powder Coated Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/ pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exceeding 4 Sqm each complete all as specified and as directed.

S&F Pressed steel door frame of size 125x60mm, double rebated for doors made out of 1.25mm thick mild steel sheet including necessary fixing lugs, hinges lock strike plate etc, complete all as directed including making good the disturbed surface of plaster and periodical to match the esisting surface.

S&F Pressed steel door frame of size 105x60mm, double rebated for doors made out of 1.25mm thick mild steel sheet including necessary fixing lugs, hinges lock strike plate etc, complete all as directed including making good the disturbed surface of plaster and periodical to match the esisting surface.

M & L for PCC 1:3:6 type C1 (20mm graded crushed stone aggregates) as in filling back of pressed steel door frames/chowkats and for fixing hold fasts, etc., complete all as specified and directed.

S&F 35mm thick Flush shutter with 1 mm thick Sunmica fixed on both sides, factory made, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S&F Solid PVC Door Frame, factory made as in bathroom, toilet, cupboard and kitchen cabinet of size 50mm x 47mm made out of 5mm prelaminated PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing

S&F Factory Made Solid PVC Moulded Door Shutter as in bathroom, toilet, cupboard and kitchen cabinet,(With BWP particle board) 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing

S&F Glazed and Skelton shutters using 2nd class hard wood 35mm thick open rebated and prepare to receive glass or gauge etc edges of framing plain and chamfered or fitted cut or mitered beads for securing glass size of member of shutter as specified in SSR Part-I section 8, clause 8.23(a) and divided in square complete all as specified.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

S & F 5.0mm thick tinted sheet glass ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane complete all as specified and directed.

S & F 3.0mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified.

Supply only mild steel Butt Hinges, 100 mm size, medium weight, cold rolled fixed with complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electro galvanised (width of flaps 30mm when open) complete all as specified

S&F 20mm thick PVC solid lining as in shelves consisting of PVC insulated panels having expanded polystyrene (EPS) stuck to 2mm thick plain colour PVC sheet duly fitted into the wall as per specifications complete all as specified and as directed.

S&F aluminium anodised barrel tower bolts of extruded section, 150 mm long (ISI marked) complete all as specified and as directed .

S&F aluminium anodised handles, 100 mm long, cast type, (ISI marked) complete all as specified and as directed .

S&F150mm aluminium handles, oval type, stove enemeled black all as directed.

S & F two lever brass mortice lock with two keys fixed to cupboard shutters complete all as specified.

S&F 300mm long aluminium sliding doors bolts, plate type, stove enameled black bolts and nuts, four on bolt plate and two on staple all as specified.

Material and Labour for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces complete all as specified and as directed.

M&L for Preparation of new or previously untreated surfaces of steel and iron surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for Preparation of old surfaces of steel and iron surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for 25mm dia fancy type SS curtain rod with brackets and knobs at both ends as per site requirement including taking down old existing PVC conduit pipes with accessories complete all as specified

S&F 15 mm bore Chromium plated Bib taps (Fancy type) with aerator cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and as directed. Make :- CERA Cat Part No. F1012151/ Jaquar Cat Part No. KUP-350037PM/Grohe Cat Part No. 20235000

S&F in repair 15mm Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. Make:- Grohe Cat Part No. 23632000/ CERA Cat Part No. F2002405/ Jaquar Cat Part No. FLR-5219N.

Supply and fix in repairs; vitreous china wash down water closet pan (pedestal pattern), white including flush pipe of polyethylene of low or high density PVC 32mm dia anti-syphonage pipe etc and connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe etc complete all as specified and as directed

Supply and fix in replacement; plastic water closet seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

Supply and fix in repair; 10 litres capacity PVC valve less symphonic action type, flushing cistern, low level, white with inlet, ball valve, PVC flush pipe, float and handle including brackets complete all as specified.

Supply and fix in repairs Toilet paper holder of of vitreous china fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed

S & F in repairs brass chromium plated tubular towel rail, 20mm dia, D type 60cm long between flanges all as specified

S & F in repairs Jet spray, CP, brass body with wall hook and 1 mtr SS pipe complete all as specified

Supply and fix in repair; vitreous china wash hand basin, white, wall hung with pedestal of size 550mmx400mm including cast iron or mild steel brackets including cutting for and pinning in brackets complete all as specified and as directed.

Supply only waste coupling 32 mm dia CP complete

S & F in repairs sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size not less than 495mm x 420mm bowl size 410mm x 330mm x 185 mm complete all as specified.

Supply and fix in replacement; 125mm size brass chromioum plated shower rose with angular arm with swivel jiont complete all as specified and directed.

Supply and fix in replacement; PVC connection 15mm dia and 60cm long with two Nos of brass check nuts and washers complete all as specified and directed.

S & F in 'repair' CP grating (with or without waste hole), 125 mm size, fixed on floor/nahani traps etc complete all as specified

Taking down rain water pipe and eaves gutters (any size and pattern) incl all fittings heads shoes bends swan necks etc.

S&F PVC 110mm bore (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls including flat iron clamps of suitable size

S&F PVC 110mm bore (SWR) bends, fixed to walls

Dismantling and disconnecting of existing CI soil vent pipe 100 mm bore fixed to wall, laid in trenches incl all fittings & accessories complete all as specified and directed.

S & F cast iron sand soil waste and vent pipe 100mm bore with or without ears fixed with chemical cement joints fixed in walls complete all as specified and directed.

S & F Cast iron soil, waste and vent pipes 100mm bore with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

S & F Bends (100mm bore radius), diminishing pieces or tapers (larger bore measured)

S&F Branch pieces,100mm bore single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches

Dismantling and disconnecting of existing CI soil vent pipe 75 mm bore fixed to wall, laid in trenches incl all fittings & accessories complete all as specified and directed.

S & F cast iron sand soil waste and vent pipe 75mm bore with or without ears fixed with chemical cement joints l fixed in walls complete all as specified and directed.

S & F Cast iron soil, waste and vent pipes 75mm bore with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

S&F Bends (75mm bore radius), diminishing pieces or tapers (larger bore measured)

S&F Branch pieces,75mm bore single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches

S & F cast iron sand soil waste and vent pipe 50mm bore with or without ears fixed with chemical cement joints fixed in walls complete all as specified and directed.

S & F Cast iron cowls 50mm bore complete all as specified and directed.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out loose and soft soil

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm.

Removing excavated material not exceeding. 50m and depositing where directed at a level not exceeding. 1.5 m above the starting point

Supply and fix in replacement; 15 mm bore stop valve (or angle valve) fancy type chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends complete all as specified and directed. Make:- ESSCO Cat Part No. MQT 526/ Prayag Cat Part No. 9910/CERA Cat Part No. F1017451.

Supply and fix in replacement; 15 mm bore stop valve (or angle valve) fancy ,(concealed type) chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends complete all as specified and directed.

Taking down or up 15 mm bore galvanised iron tubing/PL-AL-PE pipes and connection including cleaning for refixing or removal complete all as specified and directed.

Supply and fixing GI tubing medium grade, ISI marked with all fittings and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified and directed .

Refixing old GI tubing 15 mm bore pipe and connections in new or old position as on walls ceiling floors etc all as specified

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed .

Dismantling water tanks and removing to store (exc 250 & n.exc 500 ltr).

S&F Rotational moulded polyethylene 750 Ltr capacity water storage tanks ( white three layered, cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and as directed.

Dismantling of Brick tiles or terracing tiles, single layer on roofs complete all as specified & directed.

Demolition of Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified & directed.

Preparation of Roof / wall concrete/plastered surfaces & appling a coat of cold bituminous primer over cleaned surface @ 0.40 Kg/Sqm followed by APP based polymeric membrane minimum weighing 3.85kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application including torching, laid as per the manufacturers instruction with side over lap of 75mm & end over lap of 100mm & tucked into the chases on vertical surfaces if required complete all as specified and directed.

M & L for PCC 1:3:6 type B1 using 20mm graded crushed stone aggregate as in padding and levelling course on roof and terrace, finished even & fair laid and compacted in slope complete all as complete all as specified and directed.

M & L for 15mm thick plastering in CM (1:4) mixed with water proofing compound as on roof top surfaces, parapet, vertical surfaces of finish even and smooth without using extra cement complete all as specified and directed. Note: WPC shall be measured and paid separately.

M & L for Cement concrete tiles 25cm x 25cm x 20 to 22 mm thick, machine pressed; set jointed and pointed in neat cement slurry over and including 15mm thick screed in CM (1:4) with and including mixing of liquid water proofing compound as per manufacture specifications, as in roof and floor tiles complete all as specified and directed.

Supply only of Liquid water proofing compound of approved make complete all as specified and as directed.

M&L Providing, cement concrete Type B0 1:2:4 (12.5mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quoins, arches , pillars etc.

M&L for brick work with sub class ‘B’ bricks, straight or curved on planot exceeding 6 M means radius built in CM (1:4) using old size bricks complete all as specified and as directed.

M&L brick work with sub class 'B' bricks straight or curved on planot exceeding 6 m mean radius built in CM 1:4 but except bricks (old serviceable bricks to be used) complete all as specified. Note : The rate includes for cleaning of old bricks.

Material and labour for cement concrete (1:2:4) type B-1, using 20 mm graded stone aggregates as in bands, bedding, benching of manholes, coping, surface channel, roof kerbs or mud stops, rounded or chamfered on edges etc including necessary form work complete all as specified and as directed.

Material and labour 75mm thick, cement concrete 1:3:6, type C2 using 40mm graded crushed stone aggregate as in floors, plinth protection, paths, etc and finishing top surfaces even and smooth without using extra cement complete all as specified and directed. complete all as specified and as directed.

BLANK

Demolition of cement concrete (re-inforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed .

M&L for RCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) for slabs supported on walls, shelves, beams and columns, lintels, fins, facia and Chajjas in double story bldg including scafolding for repair etc and the like, including form work complete all as specified and as directed .

M&L for TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed .

Supply and fixing mild steel framed work such as cooler stand, grill gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Demolition and breaking up drain pipes (SGSW, AC or Re-inforced concrete) of any dia set in cement laid in trenches incl all fittings & accessories complete all as specified and as directed.

M & L for PCC 1:3:6 type C-2 conc bed using 40mm graded stone agg to drain pipe including packing under & haunching against the sides of pipe 200 mm dia ( internal) after these are laid in trenches complete all as specified and as directed .

M & L for 150mm dia (internal) SGSW pipes, grade 'A' laid in trenches & jointed complete all as specified and as directed .

Demolition of cement concrete in ground floor and paving not exceeding 15cm thick below or ground levels complete all as specified.

M & L for PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base, floor, path, pavings etc complete all as specified.

M & L for 25mm thick sand filling under floors or in foundations including watering and consolidation complete all as specified.

M&L for Machine Pressed Rubber Moulded Precast Coloured Interlocking Paver Block, Silicon Polished/Glossy Finish with grey cement and pigment, factory made, any shape and size, ISI marked, of 60 mm total thickness, (coloured layered thickness of min 6mm) made out of M-35 grade over 25mm thick sand cushioning below interlocking paving block complete laid dry of any description in floors, aprons etc complete all as directed. Note:- Sand cushioning shall be measured and paid separately. Design and Pattern of Paver Block shall be decided by the Accepting Officer.

M&L for precast cement concrete type B1 (1:2:4) ( 20 mm grade stone aggregate) as in kerb stone etc and set in CM 1:4 all as specified.

S & F 15 mm thick marble over & including a layer of screed bed 10 mm thick in cement mortar 1:4 including moulding to edges as in cills of windows/ vents complete all as specified.

Taking down or up 20 mm bore galvanised iron tubing and connection including cleaning for refixing or removal complete all as specified and directed.

S & F GI tubing medium grade ISI marked with all fittings and fixed to walls or laid in floors bore of pipe 20mm complete all as specified and directed.

Refixing old GI tubing 20 mm bore pipe and connections in new or old position as on walls or laid in floors etc complete all as specified and directed.

S & F 15 mm bore CP sink mixer with swinging screwed down for iron pipe and fixed coated spout complete all as specified and directed. Make :-Grohe Cat Part No. 30362000 /Jaquar Cat Part No. DRC-37309/ CERA Cat Part No. F1016501

S & F 15mm bore centre bole basin mixer with extended casted spout 450 mm long complete all as specified and directed. Make- Grohe Cat Part No. 21019003 /CERA Cat Part No. F2008461/Jaquar Cat Part No. FLR-516NB

S & F 20mm bore gate valve, ISI marked with iron wheel hand screwed both ends for iron pipe complete all as specified and directed.

Water proofing treatment to sunken slab and adjoining vertical surfaces as specified under :- (A) M & L for rendering 10 mm thick in cement plaster (1:3) using coarse sand mixed with integral water proofing compound as per manufacturer's instruciton trowel even and smooth with steel trowel on sunken surfaces. (Note:- WPC shall be measured and paid separately) (B) Applying first coat of chemical pidifin 2K (Dr Fixit) on cleared RCC surfaces @ 0.86 Kg/Sqm (minimum) as recommended by manufacturer. (C) Provide a layer glass fibre mesh of size 2.25 mm x 2.25 mm (45Grms) over first coat of chemical pidifin 2K as per manufacurers recommendation. (D) Applying second coat of chemical pidifin 2K (Dr Fixit) @ 0.86 Kg/Sqm (minimum) layer glass fibre mesh of size 2.25 mm x 2.25 mm (45 Grms) as recommended by manufacturers.

S & F ball catches with 8 mm dia steel ball and brass body & sinking plate including floating in & fixed completely, complete all as specified and directed.

S & F stainless steel handles fancy type 100mm long along with screws fixed to cupboard shutters complete all as specified and directed.

S & F stainless steel plate racks of size 900 x 600 mm x 250mm and thickness of SS sheet 1mm fixed on wall etc complete all as specified and directed.

Form work to chajjas/ shelves finished fair and even complete all as specified and directed.

S & F in repair CI floor trap 75mm dia with grating including jointing to waste pipe fixed in cement concrete 1:2:4 Type B-1 complete all as specified and directed.

S & F CP hearth faucet with 1 mtr flexible PVC pipe stainless steel complete all as specified and directed.

S & F SFRC (Steel Fibre Reinforced Concrete Cover & Frame) HD-20mm graded rectangular internal size 560 x 590 mm & external size of frame 800 x800 x 100mm including manhole cover having size 590 x590 x 50mm thick and fixed over existing manhole after demolition of PCC coping & manhole cover & set in CM 1:4 including PCC benching in (1:2:4) and finishing smooth complete all as specified and directed.

S & F 20mm float valve of PTMT any colour screwed for iron pipe and fixed ( minimum weight 20mm-112 Grms) complete all as specified.

Anti-Termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in apron/ plinth etc complete all as specified and directed.

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1cement: 2 Coarse sand) to match the existing floors complete all as specified and directed.

Anti-Termite treatment of voids in masonry using chemical emulsion one litre per hole at 300mm intervals including drilling holes at 45 degree and re-plugging them with cement mortar 1:2 (1cement: 2 Coarse sand) to match the existing floors complete all as specified and directed.

S & F in repair brass chromium plated tubular towel rail, 20mm dia, D-type, 60cm long between flags in repairs complete all as specified and directed.

S & F stainless steel fancy type peg set of six and fixed in position with steel screws complete all as specified and directed.

S & F mild steel plated continuous piano 30 mm wide type hinges fixed to cupboard shutters complete all as specified and directed.

S & F glass shelf 500 x 125mm with brass brackets complete all as specified and directed. Make- Prayag/ CERA/ Hindware.

S & F triple door corner cabinet of size 848 x 343 x 250mm fixed with screws complete all as specified and directed. Make- Prayag/ CERA/ Hindware.

S & F decorative laminate type-1 of surface finish 0.9-1 mm thick, shade and patern as approved by GE , fixed with approved adhesive as per manufacturer's instruction complete all as specified and directed.

S & F decorative laminate type-1 of surface finish 0.7 mm thick, white fixed with approved adhesive as per manufacturer's instruction complete all as specified and directed.

S & F plywood 18mm thick grade BWR, Type-BB fixed with screws/ nails to frame work and as in cupboard boxes, shutters and the like complete all as specified and directed.

S & F 2nd class hardwood moulded beading as approved 40mm wide including polishing to match the existing sufrace complete all as specified and directed.

S & F 2nd class hardwood moulded beading as approved 20mm wide including polishing to match the existing sufrace complete all as specified and directed.

Excavation in post holes (or similar holes) each not exceeding 0.5 Cum, getting out, returning, filling in the ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm , watering and removing surplus soil to a distance not exceeding 50 mtr and making good surface in soft/ loose soil complete all as specified and directed.

M & L for PCC (1:3:6) type C-2 usig 40mm graded sotne aggregate in foundations, filling and mass concrete, foundation of posts struts complete all as specified and directed.

S & F posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wires etc flat iron fillets ( for securing wire mesh etc) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Suppy only chain link MS galvanised fencing, made out of GI wire of 10 to 8 gauge aperture not exceeding 65 mm, weight not less than 3.5 Kg/ Sqm etc complete all as specified and directed. Note:- BOO ordered by GE will decide the weight of chain link fencing for payment of chain link fencing.

Fixing only chain link fencing including line wires any mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wire complete all as specified and directed. Note:- Line wire shall be measured and paid for separately as supply only rate.

Supply only mild steel round bars 10mm dia and over, as in line wires for chain link fencing cut and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S & F mild steel screw bolts ( machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt not exceeding 5cm, dia of neck 5 to 10mm complete all as specified and directed.

Taking down carefully existing copper/Aluminum point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, bell pushes, ceiling roses, pendents, regulators, sockets, light fitting, call bells etc removing materials to store for keeping in safe custody or for taking credit(credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc. to match existing complete all as specified and directed

Dismantling and taking down carefully existing underground aluminum/XLPE power cable to store for keeping in safe custody or for taking credit(credit for above items should be made as per conditions separately) complete all as specified and directed

M & L for Point wiring with multi-stranded copper conductor, single core, PVC insulated and unsheathed cable, including PVC insulated unsheathed multistranded copper conductor single core cable as earth continuity conductor to common earth and connected to earth dolly, GI terminal boxes, modular frame & cover plate (suitable for modular switch/sockets) comprising the following: -

One light point/fan point controlled by one switch & fan regulator for C/fan etc. with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC medium duty concealed conduit all as specified.

One Socket outlet three pin, 6 Amp, on the same board, with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, all as specified.

One Socket outlet three pin, 6 Amp, independent, with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC medium duty concealed conduit all as specified.

One Bell/Buzzer point controlled by one push button with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC heavy duty concealed conduit all as specified.

One light point controlled by two 2-way switch etc.with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC medium duty concealed conduit all as specified.

One socket outlet three pin, 5/15 Amp, independent, with 2.5 Sq. mm (nominal area) cable & 2.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC medium duty concealed conduit all as specified.

Note for serial item No 160.01 to 160.06: 1. Switch(es) & socket(s) shall be measured & paid for separately under respective item of Schedule 'A'. 2. GI boxes shall be fixed flush in position with cement mortar (1:4) complete all as directed.

S&F Switch modular type single pole, one way, 6 Amp, one module, complete all as specified.

S&F Switch modular type single pole one way, 16 Amp, one module, complete all as specified.

S&F Switch piano, modular, flush type single pole, two way 6/10Amp, one module complete all as specified

S&F Bell push switch modular type single pole one way, 6 Amp, one module, complete all as specified.

S&F Socket outlet modular type, multipurpose, 2/3 pin, single pole one way, 6 Amp, two module, complete all as specified.

S&F Socket outlet modular type multipurpose 2/3 pin single pole one way 6/16 Amp, two module, complete all as specified.

S&F Fan regulator, modular type, 5 step, high speed, two module complete all as specified.

S&F Ceiling rose, 3 terminal PVC/polycarbonate, suitable for 230 V, AC, 50 Hz supply.

S&F call bell ding dong type AC 230 V complete.

S&F Lamp holder PVC/polycarbonate type with back plate complete all as specified

S&F LED 5W Lamp, 6500K, base B-22 efficacy not less than 90 lumen/watt complete all as specified

S&F wall mounted extruded Aluminium/polycarbonate LED batten fixture T8(G13 holder) 1.2 m, including one LED retrofit tube 20(±10%) watt, 1.2 m T8 6500K,efficacy not less than 90 lumen/watt, extruded Aluminium/polycarbonate, PC diffusor and inbuilt driver complete including making connection complete all as specified and directed.

S&F wall mounted LED batten fitting 10 (±10%) watt, 6500K, 0.6m, efficacy not less than 90 lumen/watt , extruded Aluminium/polycarbonate, PC diffusor and inbuilt driver complete including making connection complete all as specified and directed.

S&F decorative wall light fixture made of polycarbonate suitable for retrofit 9W LED lamp(base B-22) complete with PC diffusor & including one 9W LED lamp(base B-22), 6500K, not less than 90 lumen/watt efficacy including making connection complete all as specified and directed.

S&F LED light fitting 9/10W bulkhead luminaires including LED light, driver, holder connecting up with three core flexible copper conductor cable of suitable size complete allas specified and directed

S&F LED street light fitting 35 Watt 230V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrossion resistant complete with IP 65/66 protection including fixing with GI/MS bracket made out of suitable size of light grade tube upto 1.2 mtr length bent to shape with 02 sets of MS clamps made out of minimum 3 mm MS flat iron with suitable bolt and nuts complete with making connection complete all as specified and directed

S&F in replacement sub main two single core PVC copper conductor unsheathed wire multi stranded 4 sqmm along with earth wire 4.0 sqmm copper conductor single core wire connected by common earth in and including medium grade 20mm size concealed rigid PVC conduit complete all as specified.(Note :- two lengths of 4.0 sqmm cable and one length of 4.0 sqmm earth cable alongwith pvc concealed conduit will be measured as one running length)

S&F in replacement sub main two single core PVC copper conductor unsheathed wire multi stranded 6 sqmm along with earth wire 6.0 sqmm copper conductor single core wire connected by common earth in and including medium grade 20mm size concealed rigid PVC conduit complete all as specified.(Note :- two lengths of 6.0 sqmm cable and one length of 6.0 sqmm earth cable alongwith pvc concealed conduit will be measured as one running length)

S&F in replacement sheet metal encloser double door 8 way SPN 240V ISI marked complete with neutral and earth link and bus bar complete made out of CRCA steel sheet Factory made including blanking plate for unused module complete all as specified and directed

All as per item No 179 above but 04 way TPN 415 V complete all as specified and directed.

S&F sheet metal encloser single door 2 way SPN 240V ISI marked complete with neutral and earth link and bus bar complete made out of CRCA steel sheet Factory made including blanking plate for unused module complete all as specified and directed

S&F single pole and neutral enclosure 240V with a two pin and earth plug and socket complete with one single pole MCB 20Amp complete all as specified and directed

S&F in repair MCB 6-32 Amp 240V SP 10 KA ‘C’ series complete all as specified

S&F in repair RCCB DP 40Amp 30mA 240 V for earth leakage protection complete all as specified

S&F in repair MCB 415V 40 to 100Amp TPN 10 KA ‘C’ series complete all as specified

S&F in repair RCBO 415V, 63Amp, 100mA, Four pole, for earth leakage, overload & short circuit protection complete all as specified

M & L for earthing with galvanized steel plate electrode 600 x 600 mm x 6 mm size directly burried in ground vertically to earth pit not less than 2.25 meter deep below normal ground level with top edge of the earth plate not less than 1.5 m below normal ground level surrounded with coal dust and common salt filling in alternative layers of 15 cm thick each connected to and including GI earth wire 4 mm dia by means of nuts, bolts, check nuts & washers etc connecting to earthing test point, main switch board and including 15 mm dia GI pipe light grade for protection of earth lead from earth plate to distribution board and 20 mm dia GI pipe medium grade connected with funnel having wire mess for watering purpose including necessary excavation and earth work, PCC (1:2:4) type B-1 (using stone aggregates) for earthing pit, 10mm thick cast iron cover with angle iron frame all as specified and shown in electrical plate No 3 of SSR Part-I and testing on completion including replacement of old unserviceable.

Taking down existing energy meter from site and deposit to store yard for keeping in safe custody complete all as specified and directed

S&F electronic energy meters, single phase, temper proof LCD display with PC cover, 230V, 10-60 Amp, accuracy Class-I, conforming to IS 13779-1999, IP 54, 6-Digit Bright Back-lit Display Counter Records Most Accurate Error Free Forward Energy Recording Irrespective of Current Direction. High Surge Resistant, Hackproof, Low Power Consumption, High Insulation Resistance & Dielectric Strength, Anti-Tamper Features (Phase-Neutral or Main & Load Wire Interchanged, Neutral Missing, DC Immunity, Abnormal Voltage, Earth Load Tamper Indication etc). with performance parameters to show data, time, current reading, load, voltage, KWH etc. complete all as specified and directed

Taking down unsv ceiling fan/exhaust fan, sealing cable end dismentaing blades and removing fan and blades to store yard complete all as specified and directed

S&F ceiling fan 1200mm sweep,Max 30 Watt, 5 star BLDC minimum speed 350 RPM, Min air delivery 200 CMM , corrosion resistant high performance with powder-coated set of 3 blades, 100% copper motor, with set of 2 canopy, 1 down rod, 1 shackle assembly, and accessories complete all as specified and directed

S&F exhaust fan, steel body, AC, double bearing type single phase, 230V, of size, 300mm sweep, with blades and frame and louvers complete (Arrangement of provision for fixing such as drilling, hole making and boring deemed to be included in quoted rate)

Supplying, laying, jointing & testing, underground XLPE insulated screen PVC bedded, GI steel strip or wire armoured heavy duty LT electric power cable with aluminium conductor, 1100Volts grade, cross sectional area 16 sqmm 4 core complete all as specified

Supplying, laying, jointing & testing, underground XLPE insulated screen PVC bedded, GI steel strip or wire armoured heavy duty LT electric power cable with aluminium conductor, 1100Volts grade, cross sectional area 6 sqmm 2 core complete all as specified

M & L for sand cushioning using clean local tibba fine sand for underground cable 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cable complete all as specified.. Note:- Punned thickness shall be considered for payment purpose.

M&L for Bricks protection with old size Sub class B bricks for protection of PVC/XLPE UG cable in trenches with axis perpendicular to cable, laid dry and flat, joining each other with gap between adjacent bricks not exceeding 10mm complete all as specified and directed

Supply, laying & testing Tubes(In Repair), 'light grade' galvanised, 40mm bore with all fitting, unions, elbows etc and fixed complete to walls and ceilings or laid in floors complete all as specified

M&L for providing cement concrete in foundation, filling & mass concrete etc. Any work, type B1 1:2:4(20mm graded stone aggregate) including taking down old cement concrete complete all as specified and directed

S&F post top lantern LED type 20 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistance complete with driver and lamp complete all as specified and directed

M&L LT cable jointing kit earth grade for outdoor termination, heat shrink type joint complete with jointing material and accessories suitable for 4 core XLPE armoured aluminium conductor cable of size 16 sqmm to 50sqmm complete all as specified and directed

Supply, install, testing and commissioning , BEE approved, instant water geyser, vertical type, rust proof, shock proof, electric operted single phase 230 volts AC 50 Hz of capacity 3 Ltrs complete having SS 304 tank with plug top steel wire braided flexible connection (02 Nos) with stainless steel nuts and washers , safety and multifunction valve, thermostate etc. including necessary nuts, bolts, stainless strip for fixing, making inlet and outlet connection complete all as specified and directed.

Note:-The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender from total amount of Schedule 'A'/BOQ

M/s Balvinder Singh Engineer and Contractors

M/s MITTAL CONSTRUCTIONS

V K CONTRACTOR

SHARDA ENTERPRIES

M/s Kataria Construction Company