Construction of BSC Nursing College (With Hostel Block) at Saikh Bhikhari Medical College and Hospital, Hazaribagh

Amount

Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I

Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing coarse clean local SAND IN FILLING in foundation trenches or in plinth including ramming and watering in layer not exceeding 150 mm thick with all leads and 1.5 M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer In charge (Mode of measurement compacted volume)

Surface dressing of the ground including removing vegetation and in-equalities not exceding 15cm deep and disposal of rubbish, lead upto 50m and lift upto 1.5m All kinds of soil

Clearing jungle including uprooting of Rank vegetation ,grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering-all work up to plinth level. 1.4.8 (1 Cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size)

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4(1cement:2:2 coarse sand :4 graded stone aggregate 20mm nominal size)

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Providing designation 75B one brick flat soling joints fitted with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). Beam

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cementcontent as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and including retard setting of concrete, improve workability without impairing strength andadmixtures in recommended proportions as per IS: 9103 to accelerate,reinforcement,durability as per direction of Engineer-incharge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.

All work up to plinth level

All work above plinth level upto floor V level.

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Centring and shuttering including strutting, propping etc. and removal of form for.

Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roots, landings, balconies and access platform.

Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, ressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs,(excluding landings) except spiral stair cases.

Small Lintel not Exceeding 1.5 m Clear span,moulding as in cornices,window Sills,stringcouces,bands,copings,bed Plates,anchor Blocks and the like

Edges of Slabs and Breaks in Floors & Walls under 20 cm wide

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. includIng cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured) Suspended floors, roofs, landings, beams and balconies (Plan area to be measured).

Providing Tor steel reinforcement of all dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for Tata (Tiscon),SAIL,JSPL,Electrosteel Steel Ltd.Bokaro &Vizag ( RINL)

Providing Tor steel reinforcement of 8mm. dia rods as per approved design and drawing -do- -do- TMT Fe 500 do-do

Providing Tor steel reinforcement of 10mm.,28mm,32mm Dia. bars as per approved design and drawing -do- -do -

Providing Tor steel reinforcement of 12mm,16mm,20mm,25,Dia. bars as per approved design and drawing -do- -do-

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered selfcentering arrangement that freely rotates / moves in all directions. The Self – centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in-Charge. (Material shall confirm to ASTM 6063).

Floor Joint of 100 mm gap.

Providing and fixing of expansion joint system related with wall joint (internal/external) location as per drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposedaluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063).

Wall Joint of 100 mm gap.

Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s preengineered self-centering arrangement that freely rotates /moves in all directions.The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. Material shall confirm to ASTM 6063.

Roof Joint of 100 mm gap.

Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as per design for expansion joints. 200 mm wide

Providing designation 75A work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.m. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials ranking out joints to 15mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing Designation 100A B/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9"x4.5"x3") in cement mortar (1:6) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including 10mm thick mortar joints,cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 125mm thick reinforced designation 75A brick work in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Providing designation 112 mm thick reinforced designation 100 A brick work vuith fly ash lirne brick (FLAG)confirming to lS 12894-1990 (9"x4'5"x3" ) in C.M. ( 1 . 4 ) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials,n caffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specificationand direction of E/|.

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with one side teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type decorative Double leaf flush door shutter with one side teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

supplying fitting and fixing aluminium fittings of approved quality and make to doors and eindows all complete as per building specification and direction of E/I.100 mm Tower Bolt

Providing and fixing alluminium hanging floor door stopper anodized (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc.complete:Single rubber stopper

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and anufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing.

30 mm thick plain PVC door shutters

Structural Steel Work in Single Section,Fixed with or Without Connecting plate,including Cutting,hoisting,fixing in position and appplying a priming coat of approved steel primer all Complete

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge

Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)

Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.)

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required. In gratings, frames, guard bar, ladders, railings, brackts. gates & similar works.

Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I.

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides

Providing designation 100 B one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying, Doublecharge vitrified floor tiles in different sizes (thickness to be specified by lhe manufacturer) with water absorption less than 0.08% and conforming to lS 15622/ISO 13009 of approved make in all cotours and shades, laid on 20mm thick cement mortar 1 4 (1 cement:4 coarse sand) jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete Size of tile 600x600 mm

Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge

In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand)

Acid and alkali resistant tile In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) Acid and alkali resistant tile

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Glazed Vitrified tiles Matt/Antiskid finish of siz

Size of Tile 600 x 600 mm

Providing and laying 25mm thick kota stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. 600 X 600 mm

Providing and laying 25mm thick kota stone tiles in risers of steps skirting and pillars of approved size texure and colour laid over 12mm thick cement mortar (1;30 and joined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and fixing 18mm thick mirror polished, machine cut for kitchen platforms, vanity counters facias and similar locatins of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement :4 coarse sand) with joints treated with white cement, mixe* with matching pigament-epoxy touch ups. including rubbing, curing etx. complete at all Ievels. Granite of any colour and shade Area of slab over 0.50 sqm

Extra for providing edge moulding to 18 mm thick marble stone counters, Vanities etc. over item no. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in -charge.Granite work

Extra for providing opening of required size & shape for wash basins/kitchen sink in kitchen platfometre. Vanity counters and similar location in marble/stone work including necessary holes for pillar taps etc. including rubing and polishing of cut edges etc. complete.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

Water. proofing for Old and New Roof Slab :- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible material applied with , brush, roller or spray for water proofing coating as per manufacturer specifications with following steps :-

(a)surface preparation :-Provrding and cleaning of concrete surface to remove dust, oil, grease including removal of existing loose paint / coating, and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage, leakage. On identification of seepage, cement grouting to be done with non shrink expanding admixture of Sika lndia Pvt.Ltd.

/ MYK Schomberg / Dr Fixit/Fosroc or equrivallent. Providing and reparing of all corners and joints such as those between the parapet wall and the roof slab etc shall be chamfered with '150mm X '150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent Before chamfering a prime coat shall be given with the slurry of acrylic polymer Repairing surface irregularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modified repair mortar including a coat of bonding agent of the same with cement slurry including all material, labour, tools complete.

(b)1st Coat :- Apply 1st coat of two component acrylic modified, ready to use, flexible cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roller. After 1st coat of application ,45 gsm oI Fibre glass cloth to lay when the first layer is still green. 1st coat should be applied @1.50 kg/Sqmt/coat For the purpose of measurernent tte entire treated surface will be measured."

(c) :2nd Coat:- To apply the 2nd coat of two component acrylic modified,ready to-use, flexible cementitious material right angle to the '1st coat over the glass fibre laid surface. 2nd coat should be applied @0.7 kg/ Sqmt/coat. For the purpose of measurement the entire treated surface will be measured." Alter three days of drying the 2nd coal , the rain water outles to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification lo be done as per satisfation of E/c.

The Watqrproofing Brand:*Sil<a Topseal 109hi / Fosroc Brushbond RFX/ Dr Fixit Pidiffin 2Kl MYK Aqraiin TG Product Performance - Chemical Base Part A.Acrylic copol;,mer, Part 13 Specially graded cementitious powder -Density 1.6 kg/l (mixed density) at +270C Tensile Strength -2 N/mm2 after 28 Days (with Fibre cloth) (According to ASTM D 2370)Pullout Bond Strenth-2 n/mm2 (concrete failure) (According to ISO.

all corners shall be charfered with 150mm X 150 mm fillet. The rain water outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between pvc pipe outlet and concrete surface should be packed properly with rich concrete and the peripheral mouth to be sealed with moisture insensitive epoxy putty of Sika lndia Pvt.Ltd / IVIYK Schomberg / Dr FixiUFosroc .For the purpose of measurement the entire treated surface will be measured."

(e)Groove of PCC surface should be filled with Polysulphide Sealant (Paid Separately) Brand - Sika lndia Pvt Ltd / MYK Schomberg / Dr Fixit/Fosroc

Covering of treated surface wrth PCC :- Providing 50 mm thick Cement Concrete M20 (1:1.5:3) raintaining slope in alternate 2 mIx 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and clcaned sand of F M 2 5 io 3 including screening,shuttering,and mixing cerite nt c0ncrete in mixer with admixture of integral water proofing and placing rn position,strikirrg cLrring,t-a]glgnd royality all complete as per buildirrg specifictionJand direction of E/l.Panels that has been left should be casteci nextday.-lhere should be 6 mm gap between Panels.Brand- Sika *Plastocrate plus,MYK proof WP10, Fosroc- Conplast X421ic , Dr Frx,t Prdiproof LWr

Providing and filling of 6 mm thick Groove between 50 mm PCC Panels with 6 mm thick 25 mm deep thermocol strip and filling the rest 25 mm with Polysulphide Sealant (Poring Grade)as per drawings and technical specifications and direction of E in Charge.(with 18% GST).Brand:-Sika- Polysulphide, Fosroc-Thioflex 600,Dr." Fixit Pidi Seal PS(42P),MYK Seal PS or Equivalent

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming tc IS 2645 in recommended proportions.(ii) 11 nd course of 20 mm cement plaster 1:3 (1 cement:3 coarse sand)mixed with water proofing compound in recommended proportion, (iii) Illrd course of applying blown or/residual bitumen aplied hot at 1.7 kg. per sqm of area, (iv) Ivth course of 400 micron thick PVC sheet.(Overlaps at joints of PVC shet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqni).

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 1.5mm cement punning including curing, carraige of water with all leads and lifts as per building specification and direction of E/I.

Providing 19mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.

Extra of plaster work over exterior surface for each consecutive floor above above first floor including cost of scaffolding etc. All complete as per direction of E/I.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Finishing walls with textured exterior paint of required shade: New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm.

New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coat applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:

Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.

Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass.

Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.

Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places.

Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separatel

The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or any other accreditation body which operates in accordance with ISO/ IEC 17011 and accredits labs as per ISO/IEC 17025 1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml. 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test, Tests to be conducted on site. 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor(Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/ m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in?Charge.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including:

Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.

Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.

The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Providing & fixing of 10mm 2 Layer Polycarbonate Sheet I.Q Relax Makrolon Brand Sheet with Ug 2.5/m2k, Opel White colour 50 Micron U.V. Coated & fixing with standard 60mm AluminiumProfileAlcox top & bottom section as per Drawing ( weight 1.1kg per RMT, minimum ) including EPDM Rubber Gasket for tiet sealing of aluminium section With end profile of aluminium and silicon sealant (Winsil 20 neutral grade ) as per drawing at site.

Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 14.14.2-150 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 100 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge

Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge

DT : Basic rates for 125/115mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.. (Basic Rates) Drilling upto 30 mtr. Depth below G.L. in Rural Area

SAND (UPTO 10 KM LEAD)

CHIPS (UPTO 22 KM LEAD)

Metal (UPTO 22KM LEAD)

BRICKS ( 7+1KM )

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm. depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth lead upto 50 metres.

Plant mix method (Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401) With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

Wet Mix Macadam (Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.)

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom.

Bituminous Concrete (Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 % of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 509 complete in all respects)

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Cost of Driling 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 5 HP

Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes , all complete job as per direction of E/I.

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Supply fitting and fixing lowering 40 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

ELECTRICAL WORKS

Wiring for light/ceiling fan/exhaust fan/call bell point with 2x1.5 sq.mm PVC insulated stranded copper conductor cable alongwith 1 No. 1.5 sq.mm PVC insulated copper conductor cable for earthing in PVC conduit as required. (Point shall be controlled / looped From existing point). Below items rate are exclusive from Item No. 1.3.3

Wiring for Light point / Fan point / Exhaust Fan point / Call Bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit , with modular switch ,modular plate ,suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

a) Group - A

a) Group - C

Wiring for twin controlled light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit , with 2 way modular switch ,modular plate ,suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ceiling fan/exhaust fan/call bell point with 2x1.5 sq.mm PVC insulated stranded copper conductor cable alongwith 1 No. 1.5 sq.mm PVC insulated copper conductor cable for earthing in PVC Medium conduit as required. (Point shall be controlled / looped From existing point).

Wiring with 2 x 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 1 No. 1.5 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.( For Secondary MCB Points and 5A Secondary Points)

Wiring with 2 x 2.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 1 No. 2.5 sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.( For primary 5A Socket and Primary MCB Point)

Wiring with 2 x 2.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 1 No. 2.5 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.( For Circuit wiring)

Wiring for light / power plug point with 2 x 4 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC Medium Class conduit alongwith 1 No. 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.( For 16A Socket)

DB SUBMAIN WIRING IN PVC CONDUITS

Wiring for DB submain with 4 x 16 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 2 No. 16sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for DB submain with 4 x 10 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 2 No. 10sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for DB submain with 2 x 10 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 1 No. 10 sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

POWER SOCKETS

Supplying and fixing suitable size GI box with modular plate and cover in Front on surface or in recess ,including providing and fixing 3 pin 5 / 6 amps modular socket outlet and 5 / 6 amps modular switch,connection,painting etc.as required.

S/F Modular boxes, base & cover plate :- Supplying and fixing following size / modules , GI box along with modular base & cover plate for modular switches in recess etc as required. I or 2 module (78mmx 78mmx 45mm)

S/F Modular boxes, base & cover plate :- Supplying and fixing following size / modules , GI box along with modular base & cover plate for modular switches in recess etc as required.

Sff Modular base & cover plate :- Supplyng and fxing following size / modulcs, GI box along with modular basc & cover plate for modular switches in recess etc as required. 1.28.1 l/2 modulo

Sff Modular base & cover plate :- Supplyng and fxing following size / modulcs, GI box along with modular basc & cover plate for modular switches in recess etc as required.

Supplying and fixing suitable size GI box with modular plate and cover in Front on surface or in recess ,including providing and fixing 3 pin 5 / 6 amps modular socket outlet and 5 / 6 amps modular switch,connection,painting etc.as required.

Supplying and fixing suitable size GI box with modular plate and cover in Front on surface or in recess ,including providing and fixing 6 pin 15 / 16 modular socket outlet and 15 / 16 amps modular switch,connection,painting etc.as required.

Supplying and fixing modular type 20 amps A.C. unit box with ON/OFF MCB on surface or in recess complete with connections, testing and commissioning etc as required

FINAL DISTIRIBUTION BOARD

Supplying installation, testing and commissioning of surface-recess mounting horizental type three pole and neutral,prewired, sheet steel, MCB distribution board 415 volt, dust protected and powder painted ,inclusive of 200 amps tinned copper busbar, common netrul link, earth bar, din bar for mounting MCB detachable gland /knock out plate, and with built in loose wire box, and superior make terminal connectiors for all adequate size of FR PVC insulated copper conductor upto the terminal of following way with double door as required

TPN DB DOUBLE DOOR HORIZONTAL TYPE & VERTICAL TYPE

6 way (4+18), double door , Horizontal type

8 way (4 + 24), Double door, Horizontal type

8 way (8+24), double door , vertical type

12 way (8 + 36), Double door, Vertical type

6/32 Amps SP MCBs as outgoing

40 Amps 4P MCB Isolator

63 Amps 4P MCB Isolator

63 Amps 2P RCCB -

40 Amps 2P RCCB -3Nos

63 Amps 4P MCB Isolator

Supplying and fixing following way prewired SP&N MCB distribution board of steel sheet for 240 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required.

SPN DB DOUBLE DOOR HORIZONTAL TYPE & VERTICAL TYPE

8 way, Single door

8 way, Double door

12way, Double door

6/32 amps, Single pole as outgoing

40 Amps 2P RCCB

40 Amps 2P MCB

40 Amps 2P RCCB -

TELEPHONE TV AND DATA

Providing, fixing, connecting, testing and commisssioning of zinc passivated box with moulded plate in recess or on surface moulded type with following including all necessary materials etc. as required.

2 Pair telephone cord outlet (RJ-11)

TV antina Socket outlet

Supplying and fixing of following size medium class PVC conduit alongwith the accessories in surface / recess including painting in case of surface conduit or cutting and making good the same in case of recessed conduit as required as per specification.

20mm dia

25mm dia

32mm dia

Providing and fixing of UTP CAT 6 Computer LAN Cable With Star Separator and for Telephone in existing conduits .

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying, drawing, of 0.5mm dia (2 pair) FRLS PVC insulated copper conductor , unarmoured telephone cable in existing surface/ recessed steel /PVC conduit as required

Providing, fixing, connecting and testing of following pair solderless telephonetag block, with powder coated box (Krone make ) of required size box with hinged lockable cover and clamps for dressing of wires etc as required.

100 Pair box

50 Pair box

20 Pair box

Supply and laying of following 0.61mm dia annealed tinned copper conductor PVC insulated and PVC sheathed unarmoured telephone cable in existing conduit in concealed/ surface system complete as required

100 pair Cable

50 pair Cable

20 pair Cable

Providing, fixing, connecting, testing and commisssioning of zinc passivated box with moulded plate in recess or on surface moulded type with following including all necessary materials etc. as required. 48 Port layer-2 Switch

SITC OF LIGHTING FIXTURES AND FANS

Supply and fixing circular/ hexagonal M.S. sheet ceiling fan box with clamp of internal dia 140mm, 73 mm height, 3mm thick rim top lid of 1.5mm thick M.S sheet lidss shall be screwed into M.S. box by means of 3mm round headed screws, clamps shall be made of 12 mm dia M.S bar bent to be shape as per standard drawing with over all length as 80 cm

Geyser/ Toilet Inline Fan point consisting of following :- - 1 No. 6 pin No 6/16A Modular Socket in 2 Module Box with modular Plate near Geyser - 1 No 6/16A Modular Switch in 2 Module Box with Modular plate near entry at switch board level - Wiring between Socket and Switch board with 3 Nos. 4.0 Sq. mm Cu Wire in conduit including connections at both ends. Breakup of said item is as follow:-

S/F 2 16A modular type switch.

S/F 2 16A modular type 6 pin socket.

S/F TV antenna socket outlet

Supply and fixing of stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supply and fixing of Computer terminal (RJ-45) outlet in existing box with modular plate

Supplying and fixing following 2 Module base & cover plate on existing modular metal boxes etc. as required.

Supply and imstallatiom of regular / standard make 1200 mm sweep ceiling fan including wiring the down rod .of standard length (up to 30 cm ) with 3x1.5 sq.mm FR PVC insulated copper conductor single core cable including providing and fixing phenolic laminated sheet cover on the fan box etc as required. 1200 mm ceiling Fan BLDC

Supply and fixing of call buzzer suitable for single phase , 230 Volts , complete as required

SITC of following rating recess / surface mounted LED round / square shape down light luminarie with pressure die cast housing for single phase supply voltage Luminarie shall be confirm to IS: 10322 part -5 / section -2 or IEC :62722 withh all neccesary accessories as required. (Approved Make:- Philips/Crompton/ Wipro/ India Bulls.)

12W LED Round Down Light (Recess / Surface )

15 / 16 W LED Round Down Light (Recess )

18 W LED Round Down Light (Recess )

Supply, Installation, Testing & commissioning of surface/suspended 4' LED luminaire.Extruded aluminium housing fitted with engg. Plastic end caps.Opal diffuser provides smooth light distribution LED populated on PCB comprising of LED’s connected in series parallel. It has a system wattage of 28W providing a luminaire efficacy of >100 lm/W, operating range 150 – 275V AC supply, voltages, LED Colour Temp. from 6500°K ±300°K with PF>0.95 and THD<15%, CRI <80. The system level lifetime is around 50,000 burning hours with 70% percent lumen maintenance. The luminaire is IP 20 protected. LM 79 report to be submitted for luminaire and LM 80 for LED source

S.I.T.C of following rating surface mounted LED Tube Lighting Fitting Suitable for 230V 50 Hz, Single Phase Supply etc. complete as required. 20/22 W LED Tube Light

Supply, Installation, Testing & commissioning of surface mounted Bulkhead 10W LED luminaire.Extruded aluminium housing fitted with engg. Plastic end caps. Light provides smooth light distribution LED populated on PCB comprising of LED’s connected in series parallel. It has a system wattage of 10W providing a luminaire efficacy of >100 lm/W, operating range 150 – 275V AC supply, voltages, LED Colour Temp. from 6500°K ±300°K with PF>0.95 and THD<15%, CRI <80. The system level lifetime is around 50,000 burning hours with 70% percent lumen maintenance. The luminaire is IP 65 protected. LM 79 report to be submitted for luminaire and LM 80 for LED source.

Supplying and fixing Surface mounted 80 watt High BayLED downlighter complete with integrated electronic driver & LED directly on ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying and fixing Surface mounted 30 watt High BayLED downlighter complete with integrated electronic driver & LED directly on ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supply and Installation of 300mm , 230V AC exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required

Supply and Installation of 400mm , 230V AC Wall ./ Cabin fan with Wall mounting bracket including connection, testing, commissioning etc. as required

Extra for fixing the louvers/ shutters complete with Frame for a exhaust fan of all sizes

LIGHTING PROTECTION SYSTEM

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, GI tube, having single prong at top, with 85 mm dia 3 mm thick GI base plate including holes etc. complete as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning conductor complete as required.

Providing and fixing GI-tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor as required.(for vertical run)

Providing and fixing testing joint, made of 20 mm x 3 mm thick gi strip, 125 mm long with 4 Nos. brass bolts, nuts check nuts and spring washers etc. complete as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Earthing with G.I. Earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal or coke and salt complete as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Earthing with copper . Earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal or coke and salt complete as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

SOLAR PHOTO VOLTAIC POWER GENERATION SYSTEM

Supplying installation testing and commissioning of Grid interactive roof top solar photo voltaic power generation system including all the required accessories like Solar PV module, Grid Tie invertor, arrey junction box, cabling & wiring, earthing, surge protection device, FRLSame structure for mounting of solar panel. The cell shall be poly crystaline silicon cells of 6 inch each and module efficiency shall be more than 17%. Solar module shall have linear output warranty with degradation not exceeding 0.7% FRLSom 2nd Year onwards. Minimum 80% power output must be assured at end of 25 years. The FRLSont glass of solar module shall be low iron tempered glass ARC type. Termination box shall be Thermo-plastic, IP 67 or better, UV resistant with built-in-bypass. The nominal power of a single PV module shall be minimum 325 Wp or higher. Positive power tolerance modules only to be used. RF identification tag for each solar module shall be provided inside the module and must be able to withstand environmental conditions. The solar panel shall be complience of IEC 61215, IEC 61730 certified by TUV Rheinland / UL. The solar panel shall be installed as per BOQ & detailed technical specification.

SOLAR MODULES

Supply , Installation, Testing & Commissioning of Poly Crystalline 320Wp Modules, IEC 61215/IS14286,IEC-61730 Part-1st for construction and Part-2nd for testing/safety IEC-61701/IS 61701,ISO 9001/ISO 14001,With inbuild bypass diode,Frame should be Al anodize,power tolerance of +/-3%,Vmp and Imp shall not vary more than 2%, With junction box arrangement having inbuilt bypass diode,weather proof,IP-65,with RFID tag.

GRID INVERTER

Supply , Installation, Testing & Commissioning of 40 KWp Inverter , House MPPT,DG set interactive,output should compatible with grid frequency.IGBT/MOSFET,Microprodessor,DSP,430V,3-Phase,50Hz +/-3%,Ambient tem -20 dec to +50Deg,Humidity 95%, Protection IP-65 outdoor,grid voltage tolerance -20% to +15%, No load losses lees then 1% of rated power,efficiency 93% or above, THD less then 3%,P.F more then 0.9,fully automatic,having internal protections against any fault in feedr,Built-in meter and data logger to monitor plant, inverter desing as per IEC/BIS standard for efficiency and enviornmental tests as per IEC 61683/IS 61683 and IEC 60068-2 (1,2,14,30).MPPT as per IEC 60068-2(1,2,14,30)/BIS.Junction box should be IP-65 for outdoor as per IEC 529.Inverter should be grid as well as DG integrated.

ARRAY JUNCTION BOX (Combiner)

Supply , Installation, Testing & Commissioning of Array Junction Box suitable for outdoor (IP-65), Structure mounted type construction with following items: A) Four numbers 16 Amp, 1000Volt DC, positive side pull out fuse as incomers suitable for 4 Sq. mm. Cu. flexible solar cable connection. B) Four numbers 16 Amp, 1000 Volt DC, negative side pull out fuse as incomers suitable for 4 Sq. mm. Cu. flexible solar cable. C) 8 Nos. PVC Gland for positive side fuse connection through 4Sq. mm. Solar Cable. D) 8 Nos. PVC Gland for Negative side fuse connection through 4Sq. mm. Solar Cable. E) One pair (positive and negative both) 50A, Cu Bus Bar. F) Enclosure with structure/wall mounting arrangement suitable for outdoor application along with suitable heat dissipation facility.

Supply installation and commissioning of 1.6mm CRCA sheet steel encloser complete with interconnection and distribution bus bar, AC distribution board for output of inverters with SPD consists of following equipments:- 1) Incoming 100 A, 4P MCCB 1 No.

Supply installation and commissining of 1c x 4sqmm flexible copper, 1.5KV grade, TUV certified Solar cable of approved make. (DC Solar Cable)

Supply installation and commissining of 1c x6 sqmm flexible copper wire ,TUV certified Solar wire of approved make. (DC power cable)

4Cx25 sqmm Al. Arm, 1.5KV grade, Cable. (AC Power Cable)

Supply and fixing of 2mm thick covered type pregalvanized GI cable tray of 100x50x2 MM .

Supply and fixing of double compression gland suitable for 3.5Cx50 Sq.mm, Al.Ar, XLPE Cable.

Supply and fixing of suitable Cu. Lugs of round type for 6Sq.mm Cu. UnAr XLPE Cable.

Supply and fixing of suitable Cu. Lugs of PIN type for 6Sq.mm Cu. UnAr XLPE Cable.

Supply and fixing of MC4 connector Suitable for 320Wp Module(Pair)

Supply and fixing of MC4/6 branch connector as suitable.

Ground mount fixed type structure (Module mounting structure) with all required material for execution and all the civil work

IP CCTV SYSTEM

Supplying, installation, testing & commissioning of 1080p HD Indoor IP Dome camera with1/3-inch CMOS, Sensor pixels 1920 x 1080, Sensitivity-0.04 lx (color) , Dynamic range 75 dB Wide Dynamic Range (WDR), True day/night, Automatic Electronic Shutter, Video compression H.264 ; M-JPEG, White balance, BLC, H.264 quad-streaming, Motion/tamper/audio detection, Privacy Mask, Lens 3.6 mm lens, 3-axis adjustment (pan/tilt/ rotation), ONVIF Profile S, CE Certified. (Approved Make: Honeywell / Tyco / Uniview / Bosch).

Supplying, installation, testing & commissioning of 5MP 30 fps HD indoor / outdoor IR IP bullet camera with 1/3‑inch CMOS, Sensor pixels 2612 (H) x 1980(V), Sensitivity-0.24 lx (color) 0.04 lx (mono) ,IR range 30 mtrs, Dynamic range 70 db, True day/night, Automatic Electronic Shutter, Video compression H.264 MP ; M-JPEG, White balance, BLC, Analog video output, Lens (zoom / focus) 3.6 mm lens, Two-way, full duplex Audio, Audio compression AAC, G.711, L16 , ONVIF Profile S, CE Certified. (Approved Make: Honeywell / Tyco / Uniview / Bosch).

Supply installation and commission of pann tilt zoom camera with 360 deg pan and 90 deg tilt with 36 X Zoom having maximum resolution of Max. 1920 × 1080 @30fps,true day night camera with 130 m IR range , optional, fine picture at Ultra-low light,supports compression format H.265, H.265+, H.264+, H.264, 3D Digital Noise Reduction support. (Approved Make: Honeywell / Tyco / Uniview / Bosch).

SITC of IP network recoder with following feature Processor - Dual-core embedded processor . Two-way Talk - 1 channel Input, 1 channel Output, RCA,Video Output - 1 HDMI, 1 VGA , IP Camera Input - 8/16/32 Channel IP , Compression - H.264+/H.264/MJPEG,Video Resolution - 2560 × 1920, 2048 × 1536, 1920 x 1080, 1280 x 1024, 1280 x 720, 1024 x 768 , Hard Disk - 4 SATA Ports, up to 8TB ,Motion Detection - MD Zones: 396 (22 × 18),Recording Mode - Manual, Schedule (Regular, Continuous), MD (Video detection: Motion Detection, Camera Blank, Video Loss), Alarm, Stop, Backup Mode - USB Device /Network , Interface Ports - 1 HDMI, 1 VGA, 2 USB(1 USB 2.0 , 1 USB 3.0 ), 1 RS485, 1 RS232, 1 RJ45. (Approved Make: Honeywell / Tyco / Uniview / Bosch).

Supply, Installation, Testing and commissioning of Managable 24 port Switch with Power on Ethernet (PoE) enabled, 10/100, RJ45 Access ports with PoE complete as required. (Approved Make : D- Link, CISCO / NETGEAR )

Supply, installation, testing and commissioning of of 6 TB HDD all accessories complete as required.(Approved Make- WD / Samsung)

Supply installation and commissioning of 48 inch LED monitor for disply of camera. (Approved Make : Samsung / sony )

Supply, Installation, Testing & Commissioning of Pure IP CCTV-Indoor Dome Type Camera 1/2.8" or better progressive CMOS Sensor, Varifocal Lens of 3mm to 10mm, 1920 x 1080 resolution at 25 FPS, P-IRIS ,WDR, BLC, Day Night, minimum Illumination at 50 IRE - 0.1 Lux in color and 0.001 lux B/W, Triple Streaming or better, adjustable resolution and bit rate, H.264 and MJPEG, motiom detection, AGC with ONVIF support, POE base. With all accessories IP-55 weather proof Housing, brackets, tamper proof screws, clamps, wiring etc. complete as required and as per tender specification. (CE, FCC, UL Listed).

Supply, Installation, Testing & Commissioning of Pure IP CCTV-Outdoor bullet Type Camera 1/2.8" or better progressive CMOS Sensor, Varifocal Lens of 3mm to 12mm, 1920 x 1080 resolution at 25 FPS, P-IRIS ,WDR, BLC, Day Night, minimum Illumination at 50 IRE - 0.1 Lux in color and 0.001 lux B/W, built in IR for minimum 30 mtrs., Triple Streaming or better, adjustable resolution and bit rate, H.264 and MJPEG, motiom detection, AGC with ONVIF support, POE base. With all accessories IP-66 weather proof Housing, brackets to install on the boundary, tamper proof screws, clamps, wiring etc. complete as required and as per tender specification. To carry out video surveillance of the external area of the building including the perimeter (CE, FCC, UL Listed).

Supply, Installation, Testing & Commissioning of Pure IP CCTV-Outdoor bullet Type Camera 1/2.8" or better progressive CMOS Sensor, Varifocal Lens of 3mm to 12mm, 1920 x 1080 resolution at 25 FPS, P-IRIS ,WDR, BLC, Day Night, minimum Illumination at 50 IRE - 0.1 Lux in color and 0.001 lux B/W, built in IR for minimum 30 mtrs., Triple Streaming or better, adjustable resolution and bit rate, H.264 and MJPEG, motiom detection, AGC with ONVIF support, POE base. With all accessories IP-66 weather proof Housing, brackets to install on the boundary, tamper proof screws, clamps, wiring etc. complete as required and as per tender specification. To carry out video surveillance of the external area of the building including the perimeter (CE, FCC, UL Listed).

Supply, installation, testing and commissioning of Video Management Software (VMS) and video recording software for control/monitor of the actual no. of camera quantity. Software shall be open platform and shall support Mobile client licenses and WAN connectivity. Software shall support Network Attached storage with 30 days recording at 720p /30fps in motion mode .System shall be server/Client architect as per specification. System shall support RAID-5 configuration and shall be fully redundant by using less no. of external components. The software should have failover feature. IP Camera License for Video Management software

Surveillance HDD Storage in NVR:- NVR storage as required and the storage capable of storing 30 days recording at 20 fps, minimum 1.3 MP resolution at 80% Motion, the storage should be easily scalable w/o obstructing the functionality of system or loosing the data. Full redundancy is required on NVR's and Storage,Note:-Bidders to provide complete calculation of the storage to show that total storage is able to provide 30 days recording at above parameters.

Supply, installation, testing & commissioning of client work station having Processor Intel ® i7 8th gen, with 16 GB RAM with 1 TB HDD .Operating system Windows® 10 Professional 64-bit. Dual or compatible pair of NICs, 1 Gbps. NVIDIA 2 GB dedicated Graphic Card .

Supply, installation, testing & commissioning of 55" Flat LED 4K Color Monitors.

Supply,installation, testing & commissioning of; 10/100/1000 POE L2 Ethernet Managed Switch 12 port with 2 Nos of Fibre Slot and as per specification complete as required.

Supply,installation, testing & commissioning of; '6U Network Rack (wall mounted).

Supply,installation, testing & commissioning of; 42 U Network Rack (Floor mounted).

Supply, installation, testing and commissioning of CAT-6 unarmoured Data cable including all necessary accessories.( Switch to camera) in existing PVC/MS Conduit.

Supply,installation, testing & commissioning of 3C X 1.5 sq. mm power supply cable.

Supply, installation, testing and commissioning of Optical fibre cable in existing PVC/MS Conduit .

Underground / Over ground Laying of 40 mm HDPE Pipe for OFC/ Power/ Data/ Coaxial cables

Supply, installation Testing and commissioning of compatible media converter for the interconnection of Layer two switches on optical Fiber cable backbone , complete with patch cord, LIU units as required for integration as per specification complete as required.

Supplying, installing and jointing of PVC/MS conduits on surface or concealed complete with PVC/MS junction boxes, cover plates, PVC bends, PVC saddles, base and other accessories all made in PVC/MS with screws as required to complete the job. Exposed conduiting shall be painted with red enamel paint for identification.

LIU's for splicing of fiber.

RJ-45 conectors

CAT 6 Patch Cord (3 MTR)

OFC Patch Cord (3MTR)

Splicing of fiber.

Connecting accessories for Switches, Media Converters, LIUs, cameras etc.

UPS SYSTEM

Supply, fitting, fixing, testing and installation of 20 KVA, ON Line UPS three phase input and three phase out put power system of in put voltage range 360V/380/V/400V/485V AC , Frequency range 40 HZ to 60 Hz, +/- 10% and out put voltage range 415V +/-1%, AC frequency range, 50Hz, +/-1% poower factor 0,8/3.1, Harmonic distrortion -< 2% THD (Linear Load): 5% THD (Non- Liniear Load) along with required Batteries, Battery Stand, UPS Box Battery Lead etc as required. (Approved Make- APC / SOCOMEC / NUMERIC / ETON )

UPS shall carry design output at 40 deg.

Shall have soft start and hold of for incoming supply.

Invertor capability to supply 150% load for 5 sec.

SNMP card, compatible for BMS connectivity on backnet/MODBUS, Inbuilt Isolation transforme.

Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case of 12 volt cells.

Battery shall be external type with rack and suitable for 30 minute backup on 100% load.

Suitable size of copper cable between UPS and battery bank shall be provided

UPS shall be compatible for 3 nos unit in parallel operation. (Synchronize). Parallel operation kit shall be supplied with UPS.

SITC of MS Battery Rack suitable for 15 to 20 UPS Battery Installation.

SITC of 60 nos. 65 AH Flat type Sealed Maitanace Free (SMF) Battery with 24 months replacement warranty. IS:1652:1991. (VAH Required minimum 20000 for 20 KVA UPS (65AH x 26 Nos. x 12V = 20280 VAH)

Total cost of 1 Set 20 KVA UPS, Batteries & Accessories (A+B+C)

SUB-HEAD :1 415V MAIN DISTRIBUTION BOARDS

Design, fabrication, assembling, wiring & supply, installation, testing & commissioning of Distribution Panels fabricated out of 2mm thick for structural members (Load bearing members) and 1.6mm thick for door and covers (Non load bearing members) CRCA painted sheet steel in cubicle formation with reinforcement of suitable size angle iron, channels, T irons, flats wherever necessary for large meter boards. Cable gland plates shall be provided at top and bottom both and windows for meter reading, locking arrangement (pad-lock & seal) with wiring upto KWH meter & meter to MCB shall be done by using adequately rated flexible single core copper wire. The boards shall be treated with all anticorrosive process before painting as per standards with final approved shade of powder coated as approved, 2 nos. earthing terminals shall be provided for all panels. The boards shall be suitable for 415 V, 3 phase, 4 wire, 50 Hz supply system. Boards shall be fabricated in length, height, depth etc to match with site conditions.

An approval shall be taken for each panel before manufacturing. Galvanised hardwares with zinc passivation shall be used in fabrication of boards.

Note: The following provisions shall be required to be made in the switchboard detailed below

The Switchboard shall have provision for entry of all PVCA cables from the top/bottom as required.

All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The busbar insulation shall be with heat shrinkable sleeves. SMC/DMC shrouds and busbar supports shall be used.

Suitable tinned copper extension links for incoming/outgoing cables shall be provided wherever required

Positive isolation of all breakers.

All fault level breaking capacity indicates shall be IC.S value at 415 volts (ICS = ICU = ICW = 100%).

Space Heater/ light/air filter shall be provided for each vertical compartment

Padlocking facility shall be provided on all outgoing feeders.

All ACB’s/MCCB's shall have all standard accessories such as CT’s, Arc Chute, Safety Shutters etc.

Link and drops from ACB/MCCB shall be designed for full rated current of ACB/MCCB ratings at same current density as of Main Bus Bar

2 nos. GI earth strip throughout the panel.

MDB-1 LIGHTING & POWER

Incoming #1

Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required.

630 Amp, 35/50 KA

MDB-1 Panel body enclosure

Metering, Indication & Protection:

Digital Volt Meter 0-500 Volt 3 Phase class 0.5

Digital Amp. Meter 0-500 Amp. 3 Phase class 0.5

1 Sets supply available indicating lamps with control MCBs.

R-Y-B and ON/OFF indication lamps for incomer

Bus Bar:

800A, TPN Al. Bus Bar of suitable length having Current density 1Amp/sq.mm & having high conductivity electrical grade suitable to withstand symmetrical fault level of 35 kA. Neutral busbar shall be of 100% capacity.

Outgoings

63A, 4 Pole MCCB 16KA with fixed thermal magnetic setting.

MDB -1 LIGHTING & POWER as described above as per SLD

SDB-1 UPS POWER

Incoming #1

63A, 4 Pole MCCB 16KA with fixed thermal magnetic setting.

SDB-1 UPS Panel body enclosure

1 Sets supply available indicating lamps with control MCBs.

Bus Bar:

100A, Al. Bus Bar of suitable length having Current density 1Amp/sq.mm & having high conductivity electrical grade suitable to withstand symmetrical fault level of 10 kA. Neutral busbar shall be of 100% capacity.

Outgoings

40Amp. Rating DP, MCB C Series,10ka breaking capacity.

SDB -1 UPS (Power) as described above as per SLD

SUB-HEAD II : LT CABLES

LT CABLES

Supplying of following 1100 volt grade XLPE insulated PVC sheathed aluminium conductor armoured cables as per specification as required.

3.5c x 35sq. mm.

3.5c x 25sq. mm.

4c x 16sq. mm.

4c x 10sq. mm.

4c x 6 Sq.mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ STONE WARE / METAL pipe/ Cable Trays as required. Upto 35 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3.5 core 25sq. mm.

3.5 core 35 sq. mm.

3.5 core 50 sq. mm.

4c x 16sq. mm.

4c x 10sq. mm.

3c x 6sq. mm.

Supplying and fixing of following sizes of steel conduit alongwith the accessories in surface / recess including painting in case of surface conduit or cutting and making good the same in case of recessed conduit as required as per specification.

25mm dia M.S. conduit.16 SWG M.S. conduit

32mm dia M.S. conduit.16 SWG M.S. conduit

Supplying and laying of following sizes FRLSLS PVC insulated single core copper wire in existing conduit complete as required.

2x1.5 sq mm

2x2.5 sq mm

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Analogue addressable rate of rise cum fixed temperature thermistor type heat detector with mounting base, address switch complete as required.

Addressable type Manual Call Point complete as required.

Addressable Hooter cum strobe complete as required.

Analogue addressable Fault Isolators for isolating shorted, de-wired and loose circuits between two successive Fault isolators with automatic resetting arrangement. (max. 20 devices for one fault isolators).

Analogue addressable, automatic commandable Control Switches for switching on/off various ventilation fans, pressurisation fans, zones of speakers etc. and other Fire operation related devices and complete as required.

Addressable Input Card/monitor module for connecting to Flow Switch etc.

Panel shall have programmable switch plates for controlling horn strobe zones/AHU shut off etc. from panel itself. Panel shall have inbuilt autodialer with minimum 6 line output. Panel shall have its own master fire fighting telephone/audio control/command centre.

The Panel shall also have Logic hardware and software built into it for initiating specific AHU tripping, time delay operation of strobe, subsequent operation of electronic speakers, and finally hooters.

2 loop panel

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

PUBLIC ADDRESS SYSTEM :

Supplying, installation, testing & commissioning of 6 inches dia, 2 watts, 70/100 volts ceiling speaker complete as required.

Fire Fighter Telephone System : Portable UL listed fire phone handsets in a suitable enclosure. Addressable fire phone jack plates with control/monitor module.

CENTRAL CONTROL STATIONS :

Supplying, installing, testing and commissioning of the Central Control Stations consisting of the following:

Intel Core-i7 machine.

Colour Monitor 24 inch.

Laser Printer

Mouse, Keyboard etc.

Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.

Running meters (RM) for the cable/conduit is approximate. The contractor shall measure the running meter (RM) and procurement order shall be placed accordingly. The quantities shall be confirmed before start of work to the engineer-in charge.

HT /L.T CABLES AND TERMINATIONS

Supply of cable XLPE -PVC insulated PVC sheathed galvanised steel strip armoured electric power cable with aluminium conductor 11000 volt grade of size 3.5 Core 120 sqmm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required 3c x 120 sqmm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. 3c x 120 sqmm

Supplying and making indoor cable end jointing with cast resin compound, including lugs and other jointing materials, for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 120 sq. mm

Supplying and making outdoor cable end jointing with cast resin compound, including lugs and other jointing materials, for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 120 sq. mm

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.

100 mm dia

150 mm dia

250 mmdia

Supplying of following 1100 volt grade XLPE insulated PVC sheathed aluminium / Copper conductor armoured cables as per specification as required.

3.1/2 core 300sq. mm.

3.1/2 core 150sq. mm.

3.1/2 core 240sq. mm.

3.1/2 core 120sq. mm.

3.1/2 core 95sq. mm.

3.1/2 core 70sq. mm.

3.1/2 core 35sq. mm.

3.1/2 core 25sq. mm.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe/ Cable Trays as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Supplying and making end termination of following sizes with brass compression gland including providing and crimping solderless plugs/ferrules of sizes PVC insulated PVC sheathed aluminum conductor armoured cable 1.1 KV grade.

3.1/2 core 300sq. mm.

3.1/2 core 120sq. mm.

3.1/2 core 95sq. mm.

3.1/2 core 240sq. mm.

3.1/2 core 35sq. mm.

4 core 25sq. mm.

3.1/2 core 70 sq. mm.

3.1/2 core 150 sq. mm.

3 core 10 sq. mm.

Perporated type

MS perforated cable tray painted with powder coating 150 X 50 X 1.6 mm

MS perforated cable tray Connector 150 X 50 X 1.6 mm

MS perforated cable tray Bend 150 X 50 X 1.6 mm

MS perforated cable tray painted with powder coating 300 X 50 X 1.6 mm

MS perforated cable tray Connector 300 X 50 X 1.6 mm

MS perforated cable tray Bend 300 X 50 X 1.6 mm

DG SET & SUBSTATION WORK

DIESEL GENERATING SET

Supply, Installation testing and Commissioning of Silent type Diesel Generating Set at 0.8 PF, 415 Volts, 50 cycles per second, 1500 rpm, 3 phase, suitable for parallel operation / PLC based synchronization, 0.85 load factor including circuit breaker for isolation, sound proof acoustic and weather proof enclosure, residential type silencer (as per CPCB norms-2) fabricated out of CRCA sheet of 16 SWG thickness with 9 tank pretreated before powder coating with ventillation system complete in all respects comprising of the following.

Approved Makes - Cummins / Sterling / MTU Caterpillar / Kirlosker

Diesel Engine -

Diesel Engine suitable for driving alternator of above rating, compression ignition, 4 stroke cycle, Radiator cooled, turbo charged, battery starting, 1500 RPM, suitable for above output of alternator at 40oC, 50% RH & at 210 M MSL and confirming to BS 5514, BS 649, IS 10000, capable of taking 10% overloading for one hour after 12 hrs of prime continuous loading, complete with all the accessories i.e. tachometer with hour meter, flexible coupling with guard, crank case of steel, crank shaft, conncting rods, electronic governing system, dynamically balanced flywheel, air intake manifold, Air cleaner, anti vibration pads, starter motor, including all other accessories required to complete the system.

Instrument Panel - Engine mounted Instrument Panel fitted with and having digital display for followings :

Start stop switch with key

Water temperature indication

Lubrication oil pressure indication.

Lubrication oil temperature indication.

Battery charging indication

RPM indication

Over speed indication

Low Lube oil trip indication

Engine hours indication

Alternator -

Synchronous Alternator of above capacity at 0.8 PF, 3 phase, 415 volts, 50 cycles, 4 wire, 1500 RPM, suitable for operation at 40 deg C, 50% RH & at 210 meter above MSL, capable of taking 10% overlioading for one hour after 12 hrs of prime continuous loading, brushless, self excited, self regulated through AVR, continuous duty confirming to IS 4722, BS 2613 suitable for tropical conditions, class H insulation, including terminal box suitable for bus duct termination / cable termination as required.

Approved Makes - Stamford / Leroy Somer / Greaves / Marathon

Note : - Alternator should have with all other accessories as per specified in Technical specfications.

Base Frame - Both the engine and alternator shall be mounted on suitable base frame made of MS channel which shall be installed on cement concrete foundation and vibration isolating arrangement as per recommendations of manufacturer.

Inbuilt Fuel tank of standard capacity complete with inlet and outlet connections, oil indication gauge, drain plug, air breather, fuel transfer system for automatic fuel refilling system with pump, piping, valves, level indicators etc. complete.

Daily service Fuel tank of 990 liters capacity fabricated out of 2 mm thick MS sheet complete with inlet and outlet connections, oil indication gauge, drain plug, air breather, provision for fuel transfer system, level indicators and all standard accessories etc. as required.

Exhaust Silencer - Exhaust manifold with residential silencer.

The D G set should be supplied with required hardware for external PLC based auto synchronization, auto load sharing, auto load management system.

Starting system - 24 Volt DC starting system comprising of starter motors : voltage regulator and arrangement for initial excitation complete with 12/24 Volts suitable nos. lead acid type batteries of suitable AH.

Ventillation System - Arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air into the atmosphere as per standard specifications.

Supply, Fixing, testing and Commissioning of Exhaust gas piping system of Class `B' MS pipe as per IS:1239 for upto 150 mm dia and for 200 mm dia & above MS pipe as per IS:3589 with welded joints, cut to required lengths with necessary bends, fittings, flanges, painting over primer coat, with mineral wool / rock wool insulation of minimum 75 mm thick of 150 Kg per cu M density on all sides of exhaust pipe, with chicken mesh wrapping and 26 SWG aluminium sheet cladding complete as required. The aluminum foil should be tightly cladded to insulation surface of pipe. The aluminum cladding shall be locked with sheet metal screws with other sections of aluminium foil. The measurement shall be done on the basis of centre line. (Stack height should be in accordance with emission regulations of CPCB, which will go well above the top most terrace) The exhaust piping system should be suitable for upto 550oC temperature, the surface temperature of exhaust pipe shall not exceed more than 60oC. (The rates are exclusive of support structure) (Note - Final size of exhaust pipe will be confirmed by the DG vendor after calculating the actual back pressure and submit the same to client / consultant for approval)

150 mm dia (wall thickness - 4.85 mm)

Supply & fixing of SS Bellow of following diameter 150 mm dia

Supply & fabrication of D G exhaust pipe supports by M.S angle iron of size not less than 100 x 50 mm x 6/8 mm duly grouted in the wall through minimum 8 mm thick plate and with suitable MS angle / channel iron structure. The entire MS support structure should be painted by 2 coats of anti corrosive paint over primer coat of approved shade and make. The design of support to be duly approved by the Structural Consultant / Architect before fabrication and installation.

11 KV HT VCB FOUR BREAKER PANEL BOARD (INDOOR TYPE)

Supplying, Installation, Testing & Commissioning of indoor type floor mounted metal clad, 11 KV VCB panel with 3 nos VCBs, totally inclosed & fully interlocked, horizontal drawout, horizontal isolation type breaker as per IS 13118, as amended up to date and additional specifications, having capacities as mentioned below, single break, trip free mechanism, manually charged and manually closing breaker suitable for use on 11 KV, 3 phase, 50 Hz A.C. supply with short circuit fault level of 350 MVA, complete with self contained, fully interlocked, rack in and rack out mechanism, air insulated but encapsulated copper bus bars of 630 Amp capacity, breaker featured with mechanical ON/OFF indicator with hand trip device.

Approved Makes - ABB / Siemens / Schneider / Tricolite / Ambit / ADLEC /

Spring release coil, shunt trip coil and auxiliary switch of 4 NO + 4 NC and equipped with following switchgears and accessories i/c connections for 3C x 300 sq.mm. XLPE 11 KV cable (cable entry from bottom), end termination with heat shrinkable jointing material etc. as required. (Note - Cost of end termination not included in this item).

a) 1 No, 630 Amp, VCB.

d) 1 No - Microprocessor based numericak relay with O/C, E/F and S/C protection.

e) 1 No - set of dual core dual ratio 3 CTs 100/5A of 15 VA burden and accuracy class 0.5 for metering and class 5P10 for protection.

f) 1 No. electronic type digital energy analyser having 30 days memory and parameters of KW, KWH, Power factor, frequency etc. Suitable for BMS compatible with all accessories.

g) 1 No. hooter with hooter acceptance and reset push button.

h) 1 No - Red, Yellow & Blue for phase indication.

i) 1 No - Amber for Trip indication.

j) 1 No - Red `ON' Green `OFF'indication.

k) 1 No - Spring charge indication.

l) 1 No - Auto trip indication.

m) 1 No. hooter with hooter acceptance and reset push button.

n) 1 No. master trip relay. ( Electromechanical Type )

o) 1 No.Trip ckt supervision relay. (Electromechanical Type )

a) Outgoing - 2 No, 630 Amp, VCB.

c) 2 No - Microprocessor based numericak relay with O/C, E/F and S/C protection.

d) 2 No - set of dual core dual ratio 3 CTs 100/5 A of 15 VA burden and accuracy class 0.5 for metering and class 5P10 for protection.

e) 1 No. electronic type digital energy analyser having 30 days memory and parameters of KW, KWH, Power factor, frequency etc. Suitable for BMS compatible with all accessories.

f) 2 No. hooter with hooter acceptance and reset push button.

g) 2 No - Red, Yellow & Blue for phase indication.

h) 2 No - Amber for Trip indication.

i) 2 No - Red `ON' Green `OFF'indication.

j) 2 No - Spring charge indication.

k) 2 No - Auto trip indication.

l) 2 No. hooter with hooter acceptance and reset push button.

m) 2 No. master trip relay. ( Electromechanical Type )

n) 2 No.Trip ckt supervision relay. (Electromechanical Type )

o) 2 No.auxiliary relay for transformer fault.

p) Power pack.

H.T. Panel described as above

TRANSFORMER

Design, manufacture, supply, installation, testing and commissioning of out door type copper wound transformer continuously rated for 3Ph 50 Hz at full load rating the transformer should have oil immersed winding having vector group DY-11, HT side connected in star with neutral brought out connected to provide separate earthing. The transformer shall have power terminal arrangement bushing / cable end box on HT side and cable end box on LT side. 630 KVA, 11 KV /0.415 KV, 3 phase, 4.5 % impedance, 50 Nos channels with stoppers shall be provided and fixed on the provided plinth for mounting the Transformer. The transformer should have following standard as per amended IS specification and the load * no load losses shall be limited to the values given below or as per IS 2026 and latest IS-1180 or Norms issued by SEB which ever are Lower.

Approved Makes - Crompton / ABB / Schneider / Voltamp / Sudhir Intra / Esennar

Oil Conservator with filling hole with cap and plain oil level gauge.

Silica gel dehydrating breather charged with silica gel.

Oil drain Valve

Oil Filter Valve

Lifting eyes / Hooks

Two earthing Terminals

Diagram and rating plate

Air Vent

Explosion Vent

100 mm dia thermo meter with thermometer pocket

Four bi directional plain roller

Buchholz relay

Resistance Temp detector

Marshalling box

Automatic Voltage Regulator ( AVR)

Remote Tap Changing controller ( RTCC)

Transformer 11000/415 volts with on load Tap changer -15% to +5% in steps of 1.25% with RTCC, AVR and marshalling box and other specification as per BIS Level-2

11 KV END TERMINATION:

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 3C x 185 Sqmm, 11KV XLPE

Supplying of 11 KV grade aluminium conductor, cross linked polyethylene (XLPE) insulated individual core screened, flat steel/strip armoured PVC sheathed cable complete as required.3C x 185 Sqmm, 11 KV XLPE

Laying of one number additional PILCA / PVC insulated and PVC sheathed / XLPE power cable of grade exceeding 1.1 KV but not exceeding 11 KV of size exceeding 120 sqmm but not exceeding 400 sq.mm direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning protective covering and refilling the trench etc. as required.

Supply & Laying of following sizes of 1.1KV grade Copper conductor XLPE insulated and FRLS PVC sheathed armoured control cable including termination conforming to relevant IS.

4 core, 2.5 sq.mm.

10 core, 2.5 sq.mm.

12 core, 2.5 sq.mm.

Supply & Fixing of Rubber mat 1000 mm. Wide to withstand 1.1 KV dielectric strength as per latest IS 15652-2006.

Supplying and Laying of Rubber mat 1000 mm. Wide to withstand 11 KV dielectric strength as per latest IS 15652-2006 etc. as reqd.

Supplying & Placing of First aid box as approved by St.John Ambulance Brigade /Indian Red Cross society conforming to IS : 2217 - 1963 etc as reqd.

Supplying & Installation of Shock treatment chart duly mounted on a wooden frame with glass on, as required in 2 languages (Hindi & English) etc. as reqd

EXTERNAL LIGHTING

S.I.T.C of Following rating LED Street Lighting luminare with pressure die cast housing and toughened glass cover (IP 66 protection ) in existing pole / pipe for supply voltage 100-270 AC 50Hz Luminare shall be confirm to IS :10322 part 5/ section-3 and shall be complete with all nessessary accessories as required. (Approved Make:- Philips/Crompton/ Wipro/ India Bulls.) 60W LED Street Light

S.I.T.C of Following rating LED Post Top lamp made in die cast aluminium housing with decorative clear / opel acrylic diffuser on existing pipe including connection with 1.5sq.mm coppwr conductor etc all complete as required. (Approved Make:- Philips/Crompton/ Wipro/ India Bulls.) 20/25W LED Post top lamp clear

S.I.T.C of Following rating approved make LED Bollard Fitting with cylindrical shape and inverted cone shape head of height 600 to 850 mm power input -8/9 watt with die cast aluminium housing opel with PC diffuser, IP-65/54 protection, conferming to IS : 10322 part 5 etc all complete as requird. (Excluding Plinth Charge.) (Approved Make:- Philips/Crompton/ Wipro/ India Bulls.)

Supplying & installation of 7 mtr. Height Octagonal Hot Dip galvanized pole (BOP. 7030) with top dia 70 mm bottom dia 130 mm & made of 3 mm thick sheet base plate dimensions 200x200x12 mm (LxBxT) including suitable size of foundation bolt all complete as required (without Arm). (Approved Make:- Philips/Crompton/ Wipro/ India Bulls.)

1m Single Arm Suitable for 70MM Top

2 core, 6.0 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor

Laying of oup to 25 Sqmm PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 25 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Upto 25 sq. mm

Supplying and making end termination of following sizes with brass compression gland including providing and crimping solderless plugs/ferrules of sizes PVC insulated PVC sheathed aluminum conductor armoured cable 1.1 KV grade. 2C x 6 sq mm

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/termination with GI thimble etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required.

Supplying and fixing 50mm dia GI pipe on the pole for cable entry to junction box as required.

Wiring with 2 x 2.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit alongwith 1 No. 2.5 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required

EXTERNAL LIGHTING PANEL (OUTDOOR TYPE)

INCOMING

1 No63 Amp FP Moulded Case Circuit Breaker (35 KA) with 63 Amp 4 Pole Contactor & Timer.

1 Set of phase indicating lamps.

1 Set of ON/OFF indicating lamps with SP MCB.

BUS BARS

200 Amp FP aluminium busbar with coloured heat shrinkable sleeve.

OUTGOING

08 Nos. 25 Amp DP MCB (10 KA)

03 Nos. 40 Amp DP MCB (10 KA)

Panel described as above

AUTOMATIC FIRE DETECTION GAS SUPPRESSION SYSTEM IN PANELS

Supply, fixing, testing and commissioning of Automatic Linear pneumatic Tube Detection based Novec 1230 System for Electrical Panels (consisting of the following components.Approved Makes - Firemech / Nohmi / Ceasefire / Tyco / Firetrex)

6 KG Novec 1230, DLP Assembly with automatic valve mounted on approved cylinder, push in connector for tube, Novec 1230 gas, mounting bracket, End of Line adopter and low pressure switch for monitoring system activation.

Linear pneumatic heat Detection Tube with all necessary fittings & supports

Master Control Unit with Audio Visual Alarm with wiring to make complete system operational. The Control Panel should have provision for integration with Fire Alarm/SCADA/BMS System (Supply to be provide by the end client at 220 Volt AC).

EARTHING SYSTEM

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. (with charcoal/ coke and salt) as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25mm x 5 mm G.I strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Providing Chemical maintanance free earth electrode comprising of copper coated earth electrode 3m length 17.2 mm outer dia along with 25 KGs earth connectivity enhancing back fill mineral compound for earth electrode to fill up the excavetd earth and earth inspection pit and complete as required

SANITARY FIXTURES & CP FITTINGS:

Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C of parry Hindustan or any other I.S.S.approved make with 100mm H.C.I. ‘p’ trap 15 litres C.I. pull and let go flushing cistern of names or other I.S.S.equivalent make, complete with all fittings,C.I. or C.C brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of vitreous white glazed earthenware ware footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I.

(A) 580 mm. long

With 10 lit. low level PVC Cistem

Supplying, fitting and fixing 40mm high vitreous white glazed earthen E.W.C. with ‘p’ trap of parry hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I.handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450grams 15mm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic solid state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming, all complete as per specification and direction of E/I.

(i) with 'P' trap

(b) 10 lit. low level PVC Cistem

E.W.C. with S trap

10 lit. low level PVC cistern

Supplying, fitting and fixing vitreous white glazed earthen ware indian squaling type 600x350mm urinal plate of parry, Hindustan or any other I.S.S. approved make with internal flushing rim, 100mm white glazed earthen ware channel about 1m. long 5 litre capacity C.I. automatic flushing cistern of reliance or any other approved make with fittings R.S. or C.I. brackets 15mm and 45 cm long PVC I Alkathene pipe standard G.I. flush pipe for backand front with spreader fittings and brass coupling etc. 15 mm C.I. Body 'brass spindle stop cock weight not less than 450 grams. all complete Including painting of exposed parts with 2 coats of approved paint over a coat of red oxide primer and cutting the wall and floor and making good the same as per speclflcatlon and direction of Ell.

600 mm x 350 mm size (large)

Supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approved make supported on painted C.I. or R.S. brackets 32mm C.I.brass waste, 15 mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.

Supplying fitting and fixing white glazed fire’s clay sink of approved make with overflow arrangements supported on C.I. or R.S. painted brackets 40mm. dia C.P.brass waste with C.P.brass chain and rubber plug 40 mm dia P.V.C. waste pipe about 750mm long with brass coupling at one endand 15mm C.I. body brass spindle bib cock of approved quality of weight not less than 450grams. including cutting wall and making good the same etc. all complete as per specification and direction of E/I. Kitchen sink 600mm ×450mm×250mm

Providing and fixing PTMT Bottle Trap for Wash basin. Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.

Providing & fixing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colour weighing not less than 88 gms

Providing and fixing male ended 15mm dia brass bib cock of approved quality (Wt. not less than 350gms.) with extra socket all complete as per specification and direction of E/I.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore.

Providing and fixing 100mm sand cast iron grating for gully trap.

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing lead connection pipe with heavy quality brass coupling 2 nos. at both ends etc all complete as per specification and direction of Engineer-in-charge 15 mm dia and 45 cm long

Providing and fixing 15 mm dia and 45 cm long P.V.C connection pipe with heavy quality brass coupling at both ends etc. all complete as per specification and direction of Engineer-in-Charge

Providing and fixing N.P/CP brass / PVC porcelain shower rose of 15 mm inlet etc. all complete as per specification and direction of Engineer-in-Charge 125mm dia P.V.C. Shower

Providing and fixing 15 mm size CP brass pillar cock (Weight not less than 350gms) C I body brass spindle pillar cock of approved quality as per specification and directionof Engineer-in-Charge. C.I body brass spindle

Supplying fitting and fixing the following items complete with all materials as per specification and directionof E/I.(a) Glass shelf with C P brass rail (i) 600×125 mm glass shelf complete

(b) Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror.

(I) 600 mm×450 mm size

(c)(I) CP brass towel rail 20 mm ×600 mm with bracket container

(II) CP brass dish container madium quailty with screw and hinges etc

(III) C P brass liquid soap container

Providing, Installing & fixing storage type water heater of approved shade with copper container, glasswool insulation,stove enamelled M.S jacket, thermostatically controlled inner heater with pilot neon lamps, 15mm inlet stop cock valve, on inlet connection, 15mm dia C.P flexible connection pipe in inlet & outlet suitable for working pressure of 8 kg/sqcm complete as required. ( Make - Parry Ware Product Code- C500339) Capacity 25 litres.

Special type of C.P. Bath room fittings for V.I.P. Buildings (JAL, Jaquar, Marc or equivatent make) (ISi Marked)

Bib Cock(ISI marked)

Bib Cock Long (Threaded) (ISI marked)

Stainless steel kitchen sink - with drain board 510 x 1040 mm bowl depth 200 mm

Flexible (coil shaped) PVC waste pipe for sink and wash basin 40 mm dia with length not less than 700 mm j/c PVC waste fittings

Providing & filling the joints with spun yarn,cement slurry & cement mortar 1:2(1 cement: 2 fine sand) in SCI/CI pipes.

Providing and fixing MS holder bat clamps of approved design to Sand cast iron / cast iron (spun) pipe embedded in and Including cement concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc.

For 100mm dia pipe

For 75mm dia pipe

Providing and fixing bend of required degree with access door,insertion rubber washer 3mm thick,bolts & nuts complete:

100 mm dia

Sand cast S&S iron pipe as per IS-3989

75 mm dia

Sand cast S&S iron pipe as per IS-3989

Providing and fixing plain bend of required degree.

100 mm dia

Sand cast S&S iron pipe as per IS-3989

75 mm dia

Sand cast S&S iron pipe as per IS-3989

Providing and fixing single equal plain junction of required degree with access door,insertion rubber washer 3mm thick,bolts & nuts complete:

Sand cast S&S iron pipe as per IS-3989

Sand cast S&S iron pipe as per IS-3989

Providing and fixing single equal plain junction of required degree:

Sand cast S&S iron pipe IS-3989

Sand cast S&S iron pipe IS-3989

Providing and fixing single unequal plain junction of required degree:

Sand cast S&S iron pipe IS-3989

Providing and fixing terminal guard.

Sand cast iron S&S as per IS 3989.

Sand cast iron S&S as per IS 3989.

Providing lead caulked joints to sand cast iron/centrifugally cast(spun) iron pipes & fittings of diameter

Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete,including cost of cutting and making good the walls and floors:

100 mm inlet & 100mm outlet

Sand cast iron S&S as per IS 3989.

Fixing water meter and stop cock in GI distribution branch with GI main of following sizes by providing and fixing tee,including cutting and threading the pipe etc. complete:

Providing and fixing brass stop cock of approved quality complete.

15 mm nominal bore

20 mm nominal bore

G.M. Full way Valve (ISi marked}

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

65 mm dia nominal bore

Providing and fixing unplasticised P.V.C connection pipe with PTMT Nuts coller and bush of approved quality and colour. 15mm nominal bore with 45cm length

Providing and placing on terrace (at all floor levels) Polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement amd making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

INTERNAL DRAINAGE (SOIL, WASTE,VENT & RAIN WATER DISPOSAL PIPES FITTINGS):

Providing, Fixing, testing and commissioning of UPVC pipe SWR type 'B' conforms to IS : 13592-1992 with all fittings such as bends, tees, elbow, 'Y', offset, cleaning pipe door, clamps and steel structural supports etc. including cutting the floors, walls and making good the same in cement concrete 1:2:4 & cement mortar 1:4. The wall thickness of pipe and technical characteristic conforms to IS : 13592-1992 type 'B'. The fitting dimension conforming to IS : 14735-1999. The jointing to be completed with rubber ring joint/solvent weld joint.

90 mm (OD) SWR Pipe

110 mm (OD) SWR Pipe

Providing, Fixing, testing and commissioning of UPVC 'P' trap/floor trap/urinal trap of self cleansing design with or without horn conforming to IS : 14735-1999 including setting with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 hard stone ballast 20 mm nominal size) cutting and making good the walls & floors.

110 mm (OD) x 110 mm (OD)

110 mm (OD) x 90 mm (OD)

Providing, Fixing, testing and commissioning of UPVC cleanout plug conforming to IS : 14735-1999 complete with all fitting; accessories and civil work. 110 mm OD

Providing, Fixing, testing and commissioning of UPVC waste Pipe conforming to IS : 4985-2000 class IV (6 Kg/Sq.cm) including all moulding fittings conforming to IS : 7834 (Part-1 - Part -7) 1987 such as tees, bends, reducers, coupling, adopters etc. solvent welded joint as per manufacturer recommendation including cutting and making good the walls, floors, R.C.C. work etc. (For waste connection)

Providing, Fixing UPVC floor drain including all fitting and accessories fixed in cement mortar complete in all respect. 110 mm OD x 63 mm OD

Providing, Fixing, testing and commissioning of UPVC inlet fittings with maximum 3 inlets 40, 50 & 63 mm OD size UPVC sockets, fixed to CI/UPVC traps including solvent weld joint/rubber ring joint complete with all civil work.

Providing and fixing PTMT grating of approved quality, colour and make 125 mm nominal dia with 25 mm waste hole

Providing and fixing straight/offset type flexible single body push fit type WC Pan Connector with factory supplied spring loaded seal guard with integrated single mould sealing fins made of flexible EVA Body, including bush/adaptor for use with CI Pipe as supplied with Pan Connector (For European water closet).

Providing and fixing in position stainless steel cockroch trap consisting of 0.45 mm thick inner and outer cup and 1.00 mm thick top grating (Jali) with ring to be fixed inside C.I. or uPVC ‘P’ traps with cement concrete.

Supply installation testing and commissioning wall mounted R.O.water purifier comprising 5 micron filter and UV steriliser on cold water supply to work on single phase 230 volts 50 HZ AC power supply with capacity 120 lph.

Fitting and fixing Single faucet storage type Water cooler ( Size 461 mm wide x 582 mm deep x 1217 mm height, weight 46 kg) fully stainless body having storage capacity of 40 ltrs, Cooling Capacity of 40 Ltrs./hr. with hermetic type compressor, gas cooled motor equipped with over load protector, condensor for propeller type, thermostat autometically controlled temperature, refrigerent R -22, 230 volt, single phase 50 hertz, maximum current 2.3 amp including plug top and electrical lead wire connection upto 3 metres from the cooler, water inlet and drain out connections complete in all respects of Voltas Model No 40/40 Tushar PSS type or similar type of approved make.

Supplying, Installation, Testing, commissioning and lowering of submersible pumps set as per specifications (enclosed in cage) by using `C' class column pipes (pipes including in separate column of schedule) including binding submersible cable,1no. pressure gauge with isolation cock along with column pipes with suitable size of clamps. The submersible pump set with direct coupled motor rated for 3 phase,50 cycle 415 ± 10% volts A/c supply with the following duty.

Total head - 50 mts. Flow rate - 10000 ltr/ hr.(Minimum)- 5HP motor (appx.)

Providing in position storage type hot water electrical geyser( vertical or horizontal-1.5 kw) including making connection in all respects.-AO Smith/Venus/Racold make. Capacity - 25 lts.

RAIN WATER DISPOSAL :

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion and with all fittings such as bends, tees, elbow, 'Y', offset, cleaning pipe door, clamps and steel structural supports etc. including cutting the floors, walls and making good the same in cement concrete 1:2:4 & cement mortar 1:4. The wall thickness of pipe and technical characteristic conforms to IS : 13592-1992 type 'B'. The fitting dimension conforming to IS : 14735-1999. The jointing to be completed with rubber ring joint/solvent weld joint. 160 mm OD

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 150 mm dia

Providing and fixing G.I. Pipes complete with G.I. Fittings and clamps. including cutting and making good the walls etc.

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Painting G.I. Pipes and fittings with two coats of anticorrosive bitumastic paint of approved quality

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Providing & fixing on wall face unplasticised - Ragid PVC rain water pipes conforming to IS ; 13592 Tyape A included jointing with seal ring conforning to IS ; 5382 leaving 10 mm gap for thermal expansion.

a)110 mm diameter

Providing, fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised - Rigid PVC rain water pipes conforming to IS ; 13592 Type A including jointing with seal ring conforming to IS ; 5382 leaving 10 mm gap for thermal expansion.

a)Coupler-110mm diameter

b)Bend-87.5deg-110mm diameter

c)Shoe-110mm shoe

Providing & fixing unplasticised - PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with .M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4(1cement : 4 coarse sand) and making good the wall etc. complete.

110mm dia

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15cm diameter and weighting not less than 440 grams.

DOMESTIC / FLUSHING/ HOT WATER SUPPLY :

CPVC Pipe Embedded in Wall :(Internal)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.

15 mm nominal OD

20 mm nominal OD

25 mm nominal OD

32 mm nominal OD

CPVC Pipe (Exposed) :

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

15 mm nominal OD

20 mm nominal OD

25 mm nominal OD

32 mm nominal OD

40 mm nominal OD

50 mm nominal OD

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

25 mm outer dia pipes.

32 mm outer dia pipes.

40 mm outer dia pipes.

50 mm outer dia pipes.

65 mm nominal inner dia pipes.

Thermal Insulation on CPVC Pipes (Exposed)

Providing & fixing thermal insulation on hot water pipes, a flexible electomeric foam of closed cells structure having thermal conductivity of 0.038 W/M.K at 40o C, water vapour permeability fire propagation including all accessories complete as per specification. All joints shall be sealed with adhesive & cotton tape, shall be applied to give uniform appearance & finished with polyshield protective coating. ( Pipe On Terrace )

Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l

(a) 15 mm dia wt not less than 300 gms

(a) 20mm dia wt not less than 400 gms

(a) 25 mm dia wt not less than 500 gms

(a) 32 mm dia wt not less than 700 gms

(a) 40 mm dia wt not less than 1kg

Providing and fixing forged brass auto air vent valve PN10 (10.00 Kg/cm2) rating including all fitting with ball valve & accessories. 15 mm dia

Butterfly Valves :

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

50 mm dia

65 mm dia

Providing and fixing, uPVC pipes 6 Kg/Cm2 (IS: 4985) including all fittings (plain or door) e.g. bends, junction, offsets, access pieces, jointing with rubber ring/solvent cement joints including required suports,cutting chase or holes in walls and floors and making good where required. 110 mm Dia

Providing & fixing in position uPVC P"or S" trap/elbow of self cleaning design of following sizes for the embedded areas. Making proper connection with drip- seal joints, cutting chase / hole in floors /slabs and bringing the same in proper condition in cement concrete 1:2:4 mix complete as required. including cost of cutting and making good the walls and floors where required. 110 mm inlet and 63 mm outlet (Floor Drains only)

Providing and fixing multi-floor trap fitting with maximum 3 inlets 32,40 or 50 mm size fabricated from 100/150 mm dia upvc pipes and sockets,fixed to C.I. trap with lead caulked joint and set in cement concrete as per standard drawing complete.

Providing and fixing END CAP or cleanout plug( Ceiling or Floor) with suitable inset keys for opening, male threaded joint with socket fixed to pipe complete in all respects. 110 mm OD pipe size

EXTERNAL WATER SUPPLY:

Excavating trenches of required width for pipes including excavation for sockets also including for cement concrete craddles, and dressing of sides, ramming of bottoms, depth up to 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer with minimum 95% by ramming, watering etc. and disposing off surplus excavated soil as directed, within a lead of 50 m. UPTO 1.5M Pipes exceeding 80 mm dia but not exceeding 300mm dia.

Providing, laying in position, testing & commissioning of S & S cast spun pipes conforming to IS : 1536 class 'LA' including all fittings conforming to IS : 1538 e.g. bends, tees, reducers, blank flanges, tyton joints as per IS : 3144, effective proper connection, cutting chase hole in walls & floors and making good wherever required, bed concrete & sand filling as required including thrust blocks at bends. [Location : From Bore Well/Tanker water supply line/Municipal line to Underground Water Storage Tank]. 100 mm dia

Sluice Valve :

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 80 mm dia

DUAL PLATE NON RETURN VALVE :

Providing and fixing gun metal non- return valve of approved quality (screwed end) 80 mm dia Horizontal

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) : 80 mm dia

Providing and fixing C.I. dirt box strainer for bulk type water meter with nuts, bolts, rubber insertions etc. complete conforming to IS : 2373 : 80 mm dia

Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 80mm dia

EXTERNAL SEWERAGE :

Earth Work in Excavation of required width for storm and sewer pipes including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil and then returning the soil as required in layer not exceeding 20 cms in depth including consolidating each deposited layers by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50 m. for all kinds of soil.

Pipes, exceeding 80 mm dia but not exceeding 300 mm dia.

Extra for excavating trenches for pipes, cables etc in all kinds of soil for depth exceeding 1.5m, but not exceeding 3m. (Rate is over corresponding basic item for depth up to 1.5 metre

Providing, laying and jointing glazed stoneware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:2 (1 cement :2 fine sand) and spun yarn including testing of joints.

150 mm dia.

200 mm dia.

Providing and laying 150 mm thick cement concrete 1:5:10 mix ( 1 cement : 5 coarse Sand : 10 graded stone aggregate 40 mm nominal size) alround SW pipe including bed concrete 150 mm as per standard design.

100 mm dia. S.W. pipe

150 mm dia. S.W. pipe

200 mm dia. S.W. pipe

250 mm dia. S.W. pipe

Constructing water tight brick masonry manhole with 75 class designation bricks in cement mortar 1:4 (1 cement :4 coarse sand), R.C.C. top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size). Foundation concrete 150 mm thick 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size), inside and outside plastering 12 mm thick with cement plaster 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement and making channels and benching in cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design,complete with SFRC cover Heavy duty of adequate size as per standard design and approved drawings . (Price shall include the, cost of excavation, back filling, disposal of surplus earth, dewatering & water proofing of manholes as directed at site & other associated civil works).

Inside size 900mm x 800 mm x 450 mm deep.

Inside size 120x90cm and 90cm deep including C.I. cover with frame (medium duty) 500mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) With common burnt clay FPS(non modular) bricks of class designation 7.5

Extra over item No. 4 (a) for depth exceeding 45 cm to 90 cm.

Size 120x90cm With common burnt clay FPS(non modular) bricks of class designation 7.5

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:

150 x 100mm size 'P' type with common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

180x150 mm size P type with common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement outside rought cement planter 15 mm thick with CM 1:3 (1 cement:3 coarse sand), foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement all complete as per standard design.

0.91 m deep with S.F.R.C. cover and frame (heavy duty HD-20 grade designation) 560mm dia at top conforming to IS 12592, total weight of cover and frame to be not less than 182 Kg., fixed in cement concrete 1:2:4 (1 cement : 2 Coarse sand : 4 graded stone aggregate 20 mm nominal size) including excavation in all kinds of soil refilling centering shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately). With F.P.S. bricks class designation 75.

Extra depth for circular type manhole 0.91 M internal dia (at bottom) with F.P.S. bricks beyond 0.91 M to 1.67 M.

Providing & laying S & S cast spun pipes conforming to IS : 1536 class 'LA' including all fittings conforming to IS : 1538 e.g. bends, tees, reducers, blank flanges, tyton joints as per IS : 3114, effective proper connection (For External Sewer Line + Bypass line from Equalization tank to municipal sewer) complete i/c excavation/back filling, bed concrete, sand bed, painting two or more coats with synthetic enamel paint ovr a coat of primer. 100 mm dia

STORM WATER DRAINAGE:

Earth Work in Excavation of required width for storm water drainage pipes including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil and then returning the soil as required in layer not exceeding 20 cms in depth including consolidating each deposited layers by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50 m for all kinds of soil. Pipes, exceeding 80 mm dia but not exceeding 300 mm dia.

Extra for excavating trenches for pipes, cables etc in all kinds of soil for depth exceeding 1.5m, but not exceeding 3m. (Rate is over corresponding basic item for depth up to 1.5 metre Pipes, exceeding 80 mm dia but not exceeding 300 mm dia.

Providing, laying and jointing light duty non-pressure NP2 class S/S R.C.C. pipes with collars jointing with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including curing, testing of joints etc.

150 mm dia

250 mm dia

300 mm dia

CATCH BASIN CHAMBER FOR STORM WATER:

Constructing brick masonry road gully chamber 50 x 45 x 60 cm unit brick of class designated 75 in cement mortar 1:4 (1 cement :4 coarse sand) including 500 x 450 mm precast RCC horizontal grating with frame complete as per standard design.

Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in cement mortar 1:4 ( 1 cement :4 coarse sand) with pre-cast R.C.C. vertical grating complete as per standard design:

With common burnt clay F.P.S.(non-modular) bricks of class designation 7.5 Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 ( 1 cement :4 coarse sand) including 500x450mm pre-cast R.C.C. horizontal grating with frame & vertical grating complete as per standard design:

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement outside rough cement plaster 15 mm thick with CM 1:3 (1 cement:3 coarse sand), foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement all complete as per standard design.

0.91 m deep with S.F.R.C. cover and frame (heavy duty HD-20 grade designation) 560 mm internal diameter conforming to IS 12592, total weight of cover and frame to be not less than 182 Kg., fixed in cement concrete 1:2:4 (1 cement : 2 Coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering shuttering all complete. (foot rests shall be paid for separately).

With F.P.S. bricks class designation 7.5.

Extra depth for circular type manhole 0.91m Internal dia (at bottom) with beyond 0.91 m to 1.67m.

Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement all complete as per standard design.

1.68 m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560 mm dia at top conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately).

With F.P.S. bricks class designation 7.5.

Extra depth for circular type manhole 1.22 M internal dia (at bottom) with F.P.S. bricks beyond 1.68 M to 2.29 M.

Providing orange colour safety foot rest of minimum 6mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263mm and width as 165mm with minimum 112 mm space between protruded legs having 2mm thread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138mm as per standard drawing and suitable to with stand the bend test and chemical resistant test as per specification and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manhole with 30x20x15 cm cement concrete block 1:3:6 (1cement : 3coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design

MISCELLANEOUS ITEMS:

PUDDLE FLANGE FOR WATER TANKS

Providing and fixing M.S fabricated epoxy coated(two layers) galvinised coating puddle flange comprising of 600 mm dia long M.S class 'C' pipe (screwed end up to 50 mm & flange for more than 50 mm dia) with 6 mm thick M.S plates of required size upto 150 mm dia & 7.1 mm thick mm plate for pipe dia above 150 mm dia including cutting holes in centre of plate, inserting pipe & making welded (Arc) joint complete. Same shall be installed with TEC welded joint in position with reinforcement bars of RCC tank wall/slab including making cutout in shuttering during concrete casting of tank of following diameter. (Location: underground/ overhead tanks.)

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Providing and placing on terrace storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid ISI license].

G.I VENT PIPE

Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

80 mm dia

100 mm dia

Providing and fixing of mosquito overflow grating /Jali of the following diameters including all fitings & accessories :- 100 mm dia

PUMPS

Supply, installation, testing and commissioning of Down comer pump comprising of the following:

Horizontally mounted centrifugal pump, suitable for operation on 415 volts ± 10%, 3 phase, 50 HZ A.C supply. Fire pump having C.I. body, bronze bronze impeller and S.S. Shaft with mechanical seal, capable for deliverying 900 LPM of water at 30 mts. head(motor=7.5 KW). Complete with necessary pressure gauge with gun metal shut off cock and syphon on delivery side. The pump should meet the condition of Local fire Authority.

Squirrel cage induction motor TEFC type for operation on 415 V, 3 phase 50 HZ AC supply for the above pump with a synchronous speed of 2900 R.P.M. with flexible coupling and coupling guard etc. as required.

Common base plate for (a) and (b) from M.S. channel as required size.

Suitable cement concrete foundation with plaster, Antivibration arrangement of cushy foot mounting.

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)

(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520

b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.

(c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.

(d) Suitable cement concrete foundation duly plastered and with anti vibration pads.

450 lpm at 35 m Head

CONTROL PANELS

Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, inter-connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :

INCOMING

LED type RYB phase indicating lamps, ON, OFF, trip indicating lamps Set of Copper Bus Bar 300A

PIPES & ACCESSORIES

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

40 mm dia

50mm dia

65 mm dia

80 mm dia

100 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

65mm dia

80mm dia

100mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

80 mm dia

100mm dia

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required.20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585, 20 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipmets on wall.Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way-100 mm dia M.S. Pipe

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required 150 mm width x 50mm depth x 1.6 mm thickness.

Providing and fixing dial type pressure gauge with isolation cock and pipe at hydrant station. Dial diameter 100 mm caliberation, 0-15 kg

Providing and fixing resilient rubber neoprene lined single arch vibration eliminators with unit control suitable for raw water upto 450C temperature working pressure 25 kg and test pressure 37.5 kg/cm2. 80 mm dia.

Providing and fixing heavy duty PVC insulated, PVC armoured conductor cables 1100 V grade including necessary support clamps and connection lugs complete in all respects.

Power cable 3 core 16 sq mm aluminium conductor armoured cable.

Control cable 2 core 1.5 sq mm copper conductor armoured cable.

Providing and fixing carbon-di-oxide type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to IS:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. Capacity 4.5 Kg.

Providing and fixing ABC Powder type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to IS:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. Capacity 6.0 Kg.

Providing and fixing of C.I. check valve suitable for pressure 15 Kg/Sqcm. with flanges, Nut, bolts & washers, painting etc. complete as required. a) 80 mm dia

Providing & fixing double flanged flexicon rubber expansion joint with unit control of standard length as per maufacturers specs. Working pressure of 10Kg/Sqcm including rubber gaskets, flanges, nuts, bolts and washers complete as required. a) 80 mm dia

Providing & fixing swinging type First Aid hose reel as per IS 884 in red colour with 36 mts long and 20 mm dia dia heavy duty rubber water hose, 20 mm dia globe valve stop cock, terminating with G.M. coupling & nozzle of 5mm outlet with shut off valve complete with drum and brackets for fixing on wall, bolts & nuts conforming to IS:884-1969 complete as required.

Providing and fixing standard firemans axe with heavy rubber handle.

Providing and fixing M.S cabinet size 1.2 m x 2.1x0.6 m fabricated from 1.6 mm MS sheet and M.S angle 40mm x 40mm x 6 mm complete with glass, locking arranements.

Providing and fixing ISI Marked of approved make Fire Extinguishers complete with all accessories as per manufacturer's specifications.

a) CO2 gas nozzle type - 9 Litre capacity (IS:2878).

b) Mechanical Foam gas cartridge type. 9 Kg capacity (IS:15683).

c) ABC dry powder stored pressure type 6 kg capacity (IS:15683).

Supply & installation of cast iron body 2 way 63 mm dia male instantaneous inlet coupling complete with inbuilt NRV, cap and chain for fire brigade connection conforming to IS : 904 and making connection with fire fighting pipe or under ground water tank, completing the work in all respect as per the directions of the Engineer-in-charge.

Add 18% GST

Add 1% Labour cess 1%

M/S RANG BAHADUR SINGH

M/s Satyam Builders

M/S SINGHAL ENTERPRISES