Spl repair to Building No 7 and 8 (20 x OR Qtrs ) at Old Victoria Line under GE (West) Lucknow..

Amount

Dismentling of Brick tiles or terracing tiles, any layers on roof including cement mortar beding , joints etc complete all as specified and directed.

Demolition and removing of Mud in roofs any thickness, including plastering and leeping (whether full thickness removed or only a part there of) all as specified and directed demolition materials disposed out from MoD land.

M&L PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in roof kerbs/padding /benching or mud stops, and platform for mounting service tanks, rounded,chamfered on edges including necessary use and waste of from work etc over application of neat cement slurry with 3.0kg of cement per sq. metre all as specified and directed.

M & L for cleaning of all loose dirt and dust from roof surfaces and applying roof treatment as under :- (b) Applying a coat of fibre reinforced PU primer confirming to ASTMD 412 @ 30% water dilution on prepared surfaces and laying of glass fibremesh 45 GSM over tacky surface and allow to dry. (c) Supply and applying 2 coats of Hybrid PU based elastomeric single component coating over primer surface @ 10kg /10.76 Sqm total comsumption having below properties:- 1. Elongation - 500% - 650% 2. Solid contents - 80%, 3.Tensile Strength - 1.6N/mm2 4. Adhesion to concrete - 2.2N/mm2 5. Initial hardness shore strength - 60Min. 6. Tear Strength - 14Mpa. 7. Total thickness of layer shall be 1.2 - 1.5mm. Note : The net area of water proofing treatment shall be measured without any extra allowance for laps & portion inserted in groove which shall be deemed included in the quoted rates.

M & L for brick work using fly ash brick conforming to IS-12894:2002, Non Modular, class designation 7.5, straight or curved on plan, exc 6.0 m mean radius, built in CM (1:6) including demolition of brick work or stone/boulder masonry all as specified and directed

M&L for rendering/plaster by using readymix mixture of thickness 12 mm to 15 mm on newly prepared surface and plastering the wall surface with white cement based polymer modified self curing mortar, all complete as per the direction of Engineer-in-Charge.

Repair to plaster by using readymix mixture of thickness 12 mm to 15 mm and taking down cement or cement lime plaster, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-in-Charge.

Repair to plaster by using readymix mixture of thickness 5 mm to 7 mm in ceiling including taking down cement or cement lime plaster, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-in-Charge.

Complete removal of existing treatment on wall (any number of layers ) by scrapping with steel scrappers or any other means, including filling depression of scrapped surfaces and applying two coats of oil bound distemper over and including one coat of 01 mm thick wall care putty by roller complere all as specified.

M&L preparation of New plastered surface of walls and applying two coats of oil bound distemper over and incl one coat of 01 mm thick wall care putty by roller complete all as specified and directed.

M&L for preparation of new ceiling surface and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old ceiling surface and applying three coats of white wash complete all as specified and directed.

Complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust, loose paint etc by skilled labour complete all as specified and directed.

Material & Labour for preparation of old plastered surfaces of finished walls and applying Two or more coats of 100% Premium acrylic emulsion paint enhanced with PU Serum, colour stay technology having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over a coat of 01mm thick wall care putty upto smooth surfaces complete all as specified and directed. Note- Primer and emulsion to be carried out through air less spray machine (Mechanical means)

Taking down chowkhat frame with shutter (without taking out shutter from the frame) n.exc 1.50 Sqm and removing from site as directed.

Taking down chowkhat frame with shutter (without taking out shutter from the frame)exc 1.50 Sqm and n.exc.4.00 sqm and removing from site as directed.

S & F of Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (incl M.S. hold fast/ lugs or SS dash fasteners) complete all as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S & F of Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (Incl M.S. hold fast/ lugs or SS dash fasteners) complete all as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid both side decorative type (Laminated both side) flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws all as per direction of Engineer-In-Charge.

S & F of Providing 30 mm thick FACTORY MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg/Cum Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose, (confirming as per IS:4020). The door shuld be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos, Stainless Steel butt hinges size 100mm x 25 mm x 2mm and 32 mm long steel screws drilled suitable to apss through both the walls of the M.S tube. Other hardwares should be fixed with 19x6 mm size steel screws etc, complete as per direction of Engr-in-Charge manufacturer's specification & drawings

Providing & fixing of windows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick "D" Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyster paint of 12-16 microns thick and back coated with 5-7 microns thick alkyed backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 48x25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade) 0.36 mm minimum dia of wire and average width of aperture 1.4 mm. Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10 mm square guard bars with 6"(152.4mm) pitch, complete for finished item of work including of all taxes, design as per direction of Engr-in-Charge.

S&F powder coating (Thickness of powder coating not less than 50 micron) Anodised aluminium window and ventilator shutters with louvers half portion fixed with frustrated glass and half portion louvers glass as per surface, fixed type without sash bar, aluminium section weighing 0.85 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified

Supply & fix Stainless Steel Butt hinges 100mm size as directed.

Supply & fix 150mm long alumunium anodised barrel tower bolts of extructed "ISI Marked" section as directed.

S & F 125mm size aluminium alloy handles, fabricated type extruded section, ISI marked complete all as specified and directed.

M&L for 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor with door all as specified and directed.

S&F 4 mm thick figured glass pin headed type and glazing with oil putty in square n exc 0.5 sqm in each pan as directed.

Supply& fix MS ordinary pattern spring "plate type" including roller & roller plate complete as directed. Make -"Ritz" all as specified.

S&F aluminum alloy anodized sliding door bolt 250mm long with hasp and staple (bolt type) and fixing clip of sheet and cast in extruded section and fixing bolts and sliding bolt of extruded section ISI Marked complete all as specified.

M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement mortar 1:3 for concealed water tubing etc. and making good, cutting not exc 10 cm girth in brick walls all as specified and directed.

S&F 15mm bore steel water tubes "medium grade" galvanized with all fittigs such as bends, elbows tee etc and fixed to walls and ceiling in floor including taking down steel tubing and connection 15mm bore incl cleaning for refixing or removing from site all as specified.

S&F 20mm bore steel water tubes "medium grade" galvanized with all fittigs such as bends, elbows tee etc and fixed to walls and ceiling in floor including taking down steel tubing and connection 20mm bore incl cleaning for refixing or removing from site all as specified.

S&F in repair 15 mm bore Pillar taps half turn, cast copper alloy, with capstan heads, chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe and fixed

S&F in repair Stop valves, cast copper alloy but fancy type, chromium plated with long shank and cup (concealed type),screwed down high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed

S&F in repair 15 mm bore stop valves/angle valve copper alloy, fancy type,chromium plated half turn with screwed down, high pressure with crutch or butterfly handle screwed both ends fixed to GI pipe complete all as specified and directed.

Supply & Fixing in repair 15mm bore PVC connection 450mm long with brass coupling and washer as directed.

Supply & Fixing in repair copper alloy long body bib taps half turn chromium plated suitable for 15mm bore pipe with capstain head complete all as specified.

Supply & Fixing in repair gun metal gate valve screwed both ends to 20mm bore pipe complete all as specified.

Supply & Fixing in repair CP shower rose fancy type 125mm thick with or without swivel joints any size including fixed to steel pipe or union as directed.

Supply and fixed in repair PVC rotational moulded over head storage tank 500 Lts capacity including 20mm dia PTMT float valve complete all as specified.

Supply and fixing and add in fixed in repairs of vitreous china wash hand basin flat back size 550x400mm and including brackets and CP waste coupling 32mm dia and PVC waste pipe,complete as directed.

S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

M&L in repair vitreous China squatting pan, ‘Orissa’pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) all as specified and directed.

Supply & fix in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long.

Supply & fix in repair CP Brass Tabular Towel Rail, 20mm dia D type 60cm long between flanges.

S&F glass corner shelves fancy type 6mm thick 250x250mm size and fixed over CP brass brackets all as specified and directed by Engineer-in-charge.

Supply & Fixing in repair sink without drainage board size 560x410x200 mm made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes pipe & coupling etc incl bedding in cement mortar to draft wall or cantilever brackets and connection union to pipe all as specified and directed.

S & F in repair stainless steel kitchen plate rack made out of 1.00 mm thick stainless steel of size 900x750x250 mm including screws and weight not less than 5.00 Kg complete all as specified and directed.

S&F in repair 25 mm dia stainless steel curtain rod (weight not less than 200 gm/ RM) superior quality with end brackets and end knobs and fixed to wall with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed.

S&F WPC cabinet and cupboard in required sizes at site made out of 18mm thick one side decorative lamination & other side balancing lamination sheet consisting of carcass 18mm thick WPC sheet & provision of shutters made out of 18 mm thick one side decorative laminated WPC sheet density not less than 600 kg/ Cum all required brackets SS screws etc. The panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2 mm thick edge bonding tape or 90 degree edge bent finish including all necessary fittings and required knobs in each shutters as per site requirement and as per make and specification mentioned as per drawing and all are specified and directed by Engineer-in-charge on site.

S & F auto concealed hinges SS size 103mmx64mmx28mm suitable for cabinet and wardrobe complete all as specified

Supply and fixing 30 mm width of flaps continuous piano hinges Stainless steel, bright finish or electroglavanised complete all as specified and directed.

S&F ball cateches with 8 mm dia steel bal and brass body and strike plate magnet ball catcher for cup board shutters.

S&F 100mm long aluminum anodised, hasp and staple, safety type, with mild steel hinge pin including bolts to hinge plate and fixed with screws complete all as specified and directed.

S & F in repair CI spun Hubless Pipes 100 mm bore single socketed in any length in trenches or in floors with shield coupling SS(304) with EPDM rubber gasket incl complete all as specified and directed

S & F in repair CI spun Hubless Pipes 75 mm bore single socketed in any length with rubber ring joints , fixed on walls with shield coupling SS(304) with EPDM rubber gasket complete all as specified and directed.

S & F in repair CI spun Hubless Pipes 75 mm bore single socketed in any length in trenches or in floors with shield coupling SS(304) with EPDM rubber gasket, complete all as specified and directed.

S & F in repair CI spun Hubless Pipes bends / TEE/ Oval Access door Bend/ Reducer/ WC Connector etc any radius 100mm size complete all as specified and directed.

S & F in repair CI spun Hubless Pipes bends/ TEE/ Oval Access door Bend/ Reducer/ WC Connector etc any radius 75 mm size complete all as specified and directed.

S & F in repair 100 mm dia Hubless Pipes CI Nahani trap/ P/S Trap, WC connector Push-Fit with grating including jointing to waste pipe fixed in cement concrete type B1 1:2:4 complete all as specified and directed.

S & F in repair 75 mm dia Hubless Pipes CI Nahani trap/ P/S Trap with grating including jointing to waste pipe fixed in cement concrete complete type B1 1:2:4 all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding , removing and rubbish off the premised etc.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.

M&L for glazed ceramic colour tiles of size ( 350 x450mm ) x 7mm thick in walls etc, set & joints in neat cement slurry and pointed in white or colours cement to match the colour of tiles as in skirting/dados over 10mm thick rendering in cm 1:4 complete.

M&L for Non skid ceramic colour floor tiles shade as approved size 7-8mm thick area of each tile exc 0.06 sqm but not exceeding 0.11 sqm set on 15mm thick in near cement screed(1:6) slurry and pointed incl white or colour cement to match complete all as specified and directed

M&L for Non skid ceramic colour floor tiles shade as approved size 7- 8 mm thick area of each tile exc 0.18 but n exc 0.38 Sqm set on 15mm thick in near cement screed(1:6) slurry and pointed incl white or colour cement to match complete all as specified and directed

M&L for Marble Green 18 to 20mm thick (table rubbed and premirror polished) in single piece in floors/ steps (treads/risers) and like set and jointed in neat cement slurry including pointing in epoxy grout to match marble shade, laid over and including 15mm thick screed bed in CM 1:4 incl roughening of existing stone, rounding edges and double grooves in each steps complete all as specified and directed

Demolition of PCC in ground floor and paving exc 15cm thick and below or above ground level complete all as specified.

M&L for 75 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3) all as specified and directed.

Demolition of RCC in ground floor, lintel, parapets and paving exc 15cm thick and below or above ground level complete all as specified.

M&L RCC 1:1.5:3 type B1 using 20mm graded stone agg in RCC as in lintel, upto 1.5m clear span, cills, steps, seismic and other bands, plinth courses, stiring courses, lacing courses, parapets and railing upto 60 cm in height, copings, kneelers, apex stones, bed paltes, water troughs, hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as spccified and directed.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses etc. complete all as specified.

M&L Mild Steel TMT bars 8mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Demolition laid, bedded and pointed in any mortar stone slabs and tiles of any description or thickness in floors, aprons etc all as specified and directed.

M&L Granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick screed in CM 1:4 incuding rounding to edges of stone slabs one edge complete all as directed.

M & L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

Drilling through holes in granite stone for inserting pipesetc no exc 25 mm dia complete all as specified and directed

M&L for cement concrete type B1 1:2:4 (20 mm graded aggregate) plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, provided , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed.

M&L for 35mm thick precast cement concrete louvres and jallies 1:2:4 type B-1 12.5mm aggregate , (measured solid), set in CM 1:4 including all mouldings but excluding frame complete all as specified and directed.

Demolition of sunken slab floor or WC and Bath including WC trap etc incl taking down loose filling of aggregate in any type and removing where direted and providing water proofing treatment of sunken slab in following . (a) 15mm thick rendering on vertical sides of RCC slab in CM 1:3 mixed with WP chemical Cement + of Nerolac Perma/STP/Asian Confirm to IS 2645 - 9103 as per manufacturer instructions. (b) Cleaning the concrete surface by brushing and watering and remove all surface inperfections. (c) Fixing 40mm dia PVC Pipe 450mm long bottom of the sunken and wraping of bath seal tape on the pipes inserted through walls to floor are and seal it (Perma Butyl tape product of Nerolac Perma/ STP/Asian and grouting around the inserted pipes by porable grout as directed by Engr-in-Charge. (d) Make angle fillets by mixing sand cement and Nerolac Perma Hypercrete/STP/Asian on all corners. (e) Brushing two coats with high performance cementitious elastomeric two components water proofing coating of Nerolac Perma Super 2K/STP/Asian of thickness 1mm in two coats, Above treatment shall be giving upto height 15cm from bottom slab and allow it dry completely. Above material shall be confirm to below properties- 1. Bulk Density - 1.73g/cc, 2. Elongation - 100% as per ASTM D412 (Min) 3.Hydrostatic Pressure - 4bars as per ASTM D 7088, 4. Adhesion to concrete- Greater than 1.5N/mm2, 5. Crack Bridging ability as per AS/NZS 4548.5 Min 1mm. 6. DFT - 1mm in two coats. Seperation Layer- Providing & Laying 120 gsm non woven geo textile membrane over waterproofing coating to protect the coating prior the screed. (f) Providing PCC 1:4:8 type D-2 using 40mm graded stone aggregate mixed with intergral waterproofing compound Cement + of Nerolac Perma as per manufacturer instructions in sunken slab. (g) Fill the sanitary gaps with Nerolac PermaSIKA/Asian sealing compounds complete.

Surface excavation n.exc 30 cm deep and and avg 15 cm deep and getting out soft and loose soil as specified and directed.

Providing and laying of 75 mm thick hard core broken stone/ boulders to gauge n exc 63 mm as specified and directed

M&L 75mm thick cement concrete 1:3:6 typeC-2 using 40mm graded stone aggregate as in sub bases of floors and pavings etc. finished even and fair without using extra cement complete all as specified and directed.

M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour,design & pattern as in footpa th, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & patternover and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand all as specified and directed

M&L Cement concrete 1:2:4 type B1 using 20mm graded aggregate in cills, steps, coping and like including necessary form work complete all as specified.

M & L for RCC 150 mm diameter pipes laid on 150mm thick bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/ Precast RCC with SFRC ventilating cover and frame includes all items and activities to execute and make sewer line functional for depth 0.7m- 1.65m with 150mm thick Cradle PCC 1:4:8

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6 walls of honey combed masonry with top ring of M25 concrete including interceptiong chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnection pipes of RCC/ DWC complete filled with brick bats of size 2.4M dia x 6.0 M effective depth complete all as specified and directed

RCC Conventional Septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, RCC M-30 Design Mix in Walls, Base slab, Baffle walls and roof Slab including beams etc with Vent shaft, manhole openings with cover connection etc, complete with effective depth of 1.5 meter and overall depth of 3 meter for 150 users.

M&L Brickwork with subclass‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and directed. Note :- All the unhygienic bricks obtained from demolition to be thrown away out of MoD Land.

M&L for 15 mm thick rendering in CM 1:4 on brick or concrete surfaces and finished even and smooth without using extra cement, including providing and making necessary arrengments for scaffolding all as specified and directed.

Taking down carefully copper/aluminium point wiring(light, fan,socket or power) complete with fittings such as switches, sockets, ceiling rose,fan regulators, sketch light fittings, and making good the disturbed surface of walls and floors etc as directed.

Taking down carefully main switches DB's/ MCB DB's and making good the disturbed surfaces of walls as directed.

Taking down carefully copper/aluminium sub main wiring/ service connection including teak wood batten/ conduit and making good the disturbed surface of walls as directed.

M&L, Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), with mild steel/pressed steel sunken boxes (with earth dolly) duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally, and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets and fan regulators etc, including PVC insulated multi-stranded copper conductor 1.5 Sqmm nominal cross sectional area single core F.R.L.S. cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the undermentioned points:-(NOTE: Switch and socket to be measured and paid for separately):- (a) One light/fan point controlled by one switch

(b) One socket outlet point 5 Amp on an independent board

(c) Same as item no 96 (b) but on the same board

(d) Call bell / buzzer point controlled by one bell push

(e) One light point controlled by two 2 way switch

All as item no 2(b) herein before but using 2.5 sqmm , PVC insulated, stranded copper conductor single core cable for one 3 pin 15/20 Amp socket out let point on an independent board.

S & F switch piano flush button single pole one way 5 Amp 240 volt complete as directed.

S&F switch piano flush button single pole two way, 5 Amp 240 volt complete as directed.

S & F switch piano flush button single pole one way 15 Amps complete all as specified.

S & F socket outlet flush type multipurpose 2 in 1 , 3 pin 5 and 15 Amp, 230 volts complete as directed.

S & F socket outlet flush type 5 pin 5 Amps 240 volts complete as directed

S & F ceiling rose surface bakelight two to three terminal complete as directed

S&F bell push single pole one way 5 Amp socket outlet point on an independent board .

S&F Call bell AC single pole 230 Volts Ding dong complete all as specified and directed.

S&F angle type holder insulated body with back plate suitable for batten fittings as directed.

S&F fan regulator electronic, step up socket type, 230 volt and conection complete all as directed

Supply and fixing in repairs LED lamp 7/9 watt, complete all as specified and as directed.

Supply and fixing wall/surface mounting luminaires (Mirror Light) integrated LED Batten( 2 feet) 10/12 W, 6500 K, 230V ,120 lumens/watt,with extruded aluminium housing & integrated electronic driver complete including Electrical connection with PVC three core copper flexible wire & all necessary fixing arrangements all as per specified and directed by Engr-in-charge.Make:Makes shall be provided group A cat as per latest approved make given by HQ CECC

Supply and Fixing wall/surface mounting luminaires integrated LED Batten 20 W, 6000 K,120 lumens/watt , 230V with extruded Aluminium housing 4 feet long with frosted PMMA/PC diffuser & integrated electronic driver complete including Electrical connection with PVC three core copper flexible wire & all necessary fixing arrangements all as per specified and directed by Engr-in-charge. Make Makes shall be provided group A cat as per latest approved make given by HQ CECC

S& F in repair Decorative wall light fixture wall mounting, brushed nickel finish fixture with Opal Glass diffuser suitable with 9 W LED lamp B22 base, 230 V, 6000K, complete incl all required electrical connecting arrangements all as specified and as directed. Make Makes shall be provided group A cat as per latest approved make given by HQ CECC

S&F in repair LED Building security light 24/25 Watt with high power LED source (>110lumen/watt) PDC housing, IP65 and IK 07 with 4 KV inbuilt surge protection potted driver including Electrical connection with PVC three core copper flexible wire & all necessary fixing accessories such as bracket of GI pipe light grade 40 mm dia 0.60 mtr long bend to shape as per suitable size along with all accessories, fixed on wall including bolts & nuts. Makes shall be provided group A cat as per latest approved make given by HQ CECC

Supply & fixing bulk head light fitting made from cast aluminium body with heat resistance pressure die cast housing, IP-65 protection cover suitable for bulk head fitting integrated type 6.5 W LED, 6000K , 105 lumens/watt including inbuilt electronic driver complete all as specified and as directed. Makes shall be provided group A cat as per latest approved make given by HQ CECC

M&L for two single core PVC insulated FRLS cable 6 sq mm nominal cross sectional area stranded copper conductor and one single core green PVC insulated 6.0 sqmm stranded copper conductor earth continuity FRLS cable drawn through PVC conduit 20/25 mm dia including all conduit and fixing accessaries concealed in wall including cutting chases in wall and making good disturbed surface to match of walls /ceiling complete. (Note-The cost of PVC pipe and accessoried shall be deemed to be included in the quoted rate)

M&L for two single core PVC insulated FRLS cable 4 sq mm nominal cross sectional area stranded copper conductor and one single core green PVC insulated 4.0 sqmm stranded copper conductor earth continuity FRLS cable drawn through PVC conduit 20/25mm dia including all conduit and fixing accessaries concealed in wall including cutting chases in wall and making good disturbed surface to match of walls /ceiling complete. (Note-The cost of PVC pipe and accessoried shall be deemed to be included in the quoted rate)

S & F MCB DB TPN 4 Way (Vertical Type) double door, for mounting, MCBs, isolator, ELCBs etc factory made, confirming to IS: 13032 fabricated out of CRCA sheet not less than 1.2 mm thick fitted with DIN channel, neutral link and 200 Amps rated bus bar , DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of same make as MCBs /Isolator. DB shall also be provided with label marking indicating the incoming and outgoing circuits on all way as specified. The DBs shall be of IP 42 protection class.

S&F in repairs MCCB 4 Pole, 415 V, fixed type, 100 Amps with breaking capacity 16 KA complete as directed.

S&F in replacement sheet metal enclosure for DB’s when MCB, to be used, SPN, 8 ways(2+8 way) 240 volt with 200 Amps rated bus bar made out 1.2mm thick double door complete all as specified. (MCB required to be fixed shall be paid for separately under respective items of this Schedule ‘A’)

S&F MCB SPN 32 to 63 Amp 240 volts 10 KA breaking capacity complete as directed.

S&F MCB SP 10 to 32 Amp 240 volts 10 KA breaking capacity as directed.

Supply and fixing modular ac box power unit with socket plug top and MCBs with a two pin and one pin for earth plug and socket complete with one single pole MCB 20 Amp complete all as specified.

Taking down electric meter and refixing on new board after rewiring in replacement of unservicable wire complete all as directed.

Taking down ceiling fan and exhaust fan any type and any location and refixing after oiling , greesing, painting ,servicing and writing same MES number in black colour complete all as specified and directed

Supply and fixing exhaust/fresh air fan 230/240 V of size 250 mm sweep (PVC body) 1100-1325 RPM with louvers including provn of flexible three core cable from ceiling rose to terminal for making connection , fitting on wall including all necessary fixing accessories complate all as specified and as directed.

Supply, laying and testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 Sq mm 3.5 core complete all as specified and directed.

Excavation in trenches in soft/loose soil n.exc 1.5M wide and n. exc 1.5 M depth and getting out, including framing bottom surface for laying cables and all as specified

Returning, filling in soil watering and ramming into layers of 25cm after laying of cable all as specified and directed.

Disposal of surplus soil n.exc 50M distance from the starting point and depositing where all as specified and directed.

M&L for sand cushioning to UG cables (8 cm deep before laying of cable and 15cm deep over the cable) all as specified and directed

Supply & Laying sub class `B’ bricks old sizes over the HT/LT cable laid flat for protection of cable all as specified and directed.

M & L for Earthing complete with glavanised steel earth plate elactrode 600x600x6 mm thick buried directly in ground with top edge of the plate not less 1.5 mtr deep below with top edge of the plate not less 1.5 mtr deep below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of nut , bolt, check nut and washer of galvanised iron or of steel, earth lead protected by 15 mm dia GI pipe light grade watering pipe 20 mm dia GI light grade GI wire meshed funnel alternate layer of charcoal and salt PCC chamber , reassed for and including RCC cover including all necessary excavation and earth work, earth wire connected to main switch board, testing the earthing after completion all as specified and shown in electric plate no 5 of MES SSR Pt-I 2009 print and as directed.

rajan construction (BID ID -3371441)

M/s Vatsh Raj and co (BID ID -3363392)

BAJAJ CONSTRUCTION (BID ID -3370680)