REPAIR TO INTERNAL PLASTER, PAINTING AND MISC ITEMS OF B/R AND E/M IN MD ACCN BADLU SINGH ENCLAVE AND PEERU SINGH ENCLAVE UNDER AGE BR-III AND AGE E/M OF GE NORTH BATHINDA AT BATHINDA MIL STN

Amount

SCHEDULE 'A' B/R Works

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises and material and labour for non skid ceramic coloured tiles 7 to 8mm thick, repair area not exceed 0.5 Sqm in floors set and jointed in neat cement slurry over & including 15mm thick screed bed of mortar 1:6 and pointed with white/coloured cement to match, complete all as specified and as directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises and material and labour for glazed ceramic coloured tiles 7 to 8mm thick, repair area not exceed 0.5 Sqm in on vertical surface as in dados, skirting etc., set and jointed in neat cement slurry over & including 10mm thick plaster of mortar 1:4 and pointed with white/coloured cement to match, complete all as specified and as directed by Engineer-in-charge.

M & L washed stone grit plaster on exterior wall in two layers under layer 12 mm thick plaster in CM 1:4 furrowing the under layer with scratching toll applying cement slurry on the under layer @ 3 kg/sqm. Top layer 15 mm thick with coloured stone chipping of 10 mm nominal size mix with cement in ratio 1:2 in panels of size 1.2x1.2 m with grove all round as per approved patterns including scrrubing and washing the top layers with brushes and water to expose the stone chipping, including taking down old grit plaster complete all as specified and directed by Engineer-in-charge.

Taking down cement or cement lime plaster from brick wall etc including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for plastering 15mm thick on internal surface at any story or any height in cement mortar (1:6) on any face of Brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rendering/plastering 10mm thick in cement mortar (1:3) on any face of ceiling, finished fair and even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparing newly plastered or concrete surface of ceiling by sand papering or by any other mean and after preparing the surfaces applying three coats of white wash complete all as specified & directed by Engineer-in- charge

Material and labour for preparation of new plastered surfaces of walls/pillars /cornices by brooming down with using broom/sand papering or by any other means, and preparing the surfaces smooth by applying white cement based putty to make the surface even and smooth by using sander machine (with provision of dust sucking) upto entire satisfaction of Engineer-in-charge, and after preparing the surfaces applying two coats of oil bound distemper (washable), as approved tint/colour by using paint roller brush complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Preparation of old decorated surfaces (plastered/unplastered) of walls/pillars /cornices by removing / scraping down all loose particle, smoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom / steel patti / wire brush / sand papering or by any other mean and to make the surface even and smooth and also using sander machine (with provision of dust sucking) on uneven surface to make the surface even and smooth upto entire satisfaction of Engineer-in-charge and after preparing the surface smooth applying one coat of lime white wash with using paint brush complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Preparation of old decorated surfaces (plastered/unplastered) of ceiling by removing / scraping down all loose particle, smoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom / steel patti / wire brush / sand papering or by any other mean and to make the surface even and smooth and also using sander machine (with provision of dust sucking) on uneven surface to make the surface even and smooth upto entire satisfaction of Engineer-in-charge and after preparing the surface smooth applying one coat of lime white wash with paint brush complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old decorated surfaces (plastered/unplastered) of walls/pillars /cornices by removing / scraping down all loose particle, smoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom / steel patti / wire brush / sand papering or by any other mean, and to make the surface even and smooth and also using sander machine (with provision of dust sucking) on uneven surface to make the surface even and smooth upto entire satisfaction of Engineer-in-charge, and after preparing the surface smooth applying one coat of oil bound distemper (washable) by using electric paint roller or roller brush, as per existing or as approved tint/colour complete all as specified and as directed by Engineer-in-Charge.

Material and labour for complete removal of existing treatment (any layers of existing treatment ) from walls/pillars/cornices by scraping down with using mechanical sander machine (including provision of dust sucking) upto entire satisfaction of Engineer-in-charge, brooming and washing down and preparing the surfaces smooth and after that applying two coats of white cement putty(JK /Birla wall care putty), preparatory to distempering and after prepare the surface smooth applying two coats of oil bound distemper (washable) as per approved tint/colour by using paint brush or roller brush complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using clean cloths and dry paint brush & applying one coat of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossing finish with using paint brush complete as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using clean cloths and dry paint brush & applying two coat of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossing finish with using paint brush complete as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using sanded paper, clean cloths and dry paint brush & applying one coat of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossing finish with using paint brush complete as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using sanded paper, clean cloths and dry paint brush & applying two coat of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossing finish with using paint brush complete as specified and as directed by Engineer-in-Charge.

Supply & fixing in replacement kitchen plate rack made of stainless steel not less than 1mm thick with fixing accessories, overall minimum size 600mm x 750mm, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement bib tap cast copper alloy, chromium plated with crutch or butterfly handle with capstan head, wall flange, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply and fixing in replacement 10 litres capacity PVC valveless syphonic action type low level flushing cistern white with inlet, ball valve, float, handle including brackets and 32mm dia PVC flush pipe complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement 450 mm long PVC connection 15mm size with PTMT nuts complete all as specified & directed by Engineer-in-charge.

Supply & fixing in replacement flush kit of any type accessories with inlet ball valve float and handle, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement waste pipe and waste coupling of any size and any type for sink/WHB, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball (polythene float) complete, screwed suitable for 20mm bore iron pipe complete all specified and as directed by Engineer-in-charge. Note :- The minimum weight of ball valve shall be as given in SSR or in relevant IS.

Supply and fixing in replacement stop valve/angle valve cast copper alloy, with crutch or butterfly handle, screwed down, screwed both end for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply & fixing in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tack or stainless steel wire staples complete all as specified & directed by Engineer-in- charge

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips, complete all as specified & directed by Engineer-in- charge.

Supply and fixing in repair of any type of aluminium window shutters/door shutters, including necessary jointing cleats, glazing clips, rubber neoprene packing, handles, hinges, tower bolts, anodised aluminium snap beading screws etc., complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 5.5 mm thick sheet glass ordinary quality & glazing with rubber beading in square/rectangle shape fixed in window not exceeding 0.5sqm in each pane complete all as specified & directed by Engineer-in- charge.

Supply and fixing 4 mm thick sheet glass ordinary quality & glazing with oil putty in square/rectangle shape fixed in window not exceeding 0.5sqm in each pane complete all as specified & directed by Engineer-in- charge.

Supply and fixing 3 mm thick frosted glass ordinary quality & glazing with oil putty in square/rectangle shape fixed in window/ventilator not exceeding 0.5sqm in each pane complete all as specified & directed by Engineer-in- charge.

SCHEDULE 'A' E/M Works

Taking down carefully/aluminium point wiring (light, fan, socket or power point ) complete including fitting such as hylem sheet switches, ceiling rose, pendent holder sockets, regulator except concealed conduit and sunken boxes etc and making good distrubed surfaces of wall and floors etc to match with the existing, complete all as specified and directed by Engineer-in-charge.

Material and labour for point wiring complete with 1.5 sqmm (nominal area) PVC insulated and unsheathed multi stranded copper conductor FRLSH cable (ISI marked) in existing concealed surface conduit/casing caping for one light point /fan point controlled by one switch including 1.5 sqmm single core multi stranded FRLSH copper earth wire to common earth and connecting to earth dolly and existing MS Sunken box and incl 3 mm thick laminated sheet, complete all as specified and directed by Engineer-in-charge.

All as per item No 34 here in before but for socket outlet 5 pin 5 Amp on same board, complete all as specified and directed by Engineer-in-charge.

All as per item No 34 here in before but for socket outlet 5 pin 5 Amp on independent board but not below the switch board, complete all as specified and directed by Engineer-in-charge.

All as per item No 34 here in before but for socket outlet 6 pin, 5/15 Amp multi purpose, 2 in 1 on independent board with 2.5 Sqmm cable & including 2.5 sqmm single core multi stranded FRLSH copper earth wire to common earth, complete all as specified and directed by Engineer-in-charge.

All As per item No 34 in before but for bell/buzzer point, complete all as specified and directed by Engineer-in-charge.

All As per item No 34 in before but for one light point controlled by Two Two way switch, complete all as specified and directed by Engineer-in-charge.

Taking down carefully copper/aluminium point wiring (light/fan/socket or power point) complete fitting such as hylem sheet switches,ceiling rose, pendent holder, sockets,regulators including rusted/broken concealed/surface conduit and sunken boxes etc and making good disturbed surfaces of wall and floor etc to match with the existing, complete all as specified and directed by Engineer-in-charge.

Material and labour for concealed point wiring complete with 1.5 sqmm (nominal cross section area ) FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked ) drawn through and including PVC rigid conduit 20mm dia( heavy duty ) with all fittings and all accessories i.e pipe bend pipe hook, elbow,junction box, pressed steel powder coated sunken boxe of suitable size (min 60mm deep, suitable length and 1.2mm thick ), 3mm thick bakelite plastic laminated sheet for mounting switches and socket ,fan regulator, for light/fan point controlled by one switch, top cover fixed with brass screws & cup washers including provn of 1.5 sqmm FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc including cutting chases in wall and making good distrubed surface of wall/ceiling/floors etc by using CM (1:3 ) to matching with existing surface, complete all as specified and directed by Engineer-in-charge.

All as per item No 41 here in before but for socket outlet 5 pin 5 Amp on same board, complete all as specified and directed by Engineer-in-charge.

All as per item No 41 here in before but for socket outlet 5 pin 5 Amp on independent board but not below the switch board, complete all as specified and directed by Engineer-in-charge.

All as per item No 41 here in before but for socket outlet 6 pin, 5/15 Amp multi purpose, 2 in 1 on independent board with 2.5 Sqmm cable & including 2.5 sqmm single core multi stranded FRLSH copper earth wire to common earth, complete all as specified and directed by Engineer-in-charge.

Supply and fixing 6 Amps Switch 250 volts AC one way ISI marked, complete all as specified and directed by Engineer-in-charge.

Supply and fixing 6 Amps Socket 5 pin shuttered 250 volts AC ISI marked, complete all as specified and directed by Engineer-in-charge.

Supply and fixing Switch 16 Amps 250 volts AC ISI marked, complete all as specified and directed by Engineer-in-charge.

Supply and fixing Socket universal 6/16 Amps 250 volts AC shuttered ISI marked, complete all as specified and directed by Engineer-in-charge.

Supply and fixing 6 Amps Switch 250 volts AC two way ISI marked, complete all as specified and directed by Engineer-in-charge.

Supply and fixing Bell Push 6 Amp 250 volts AC ISI model fantasy, complete all as specified and directed by Engineer-in-charge.

Supply and fixing Fan regulator Electronic step type (1-4), socket type 230- 240 volt AC supply, complete all as specified and directed by Engineer-in-charge.

Supply and fixing ceiling rose 3 plate flush type 6 Amp 250V AC topline series with polycarbonate 20 X 50 mm two to three terminal, complete all as specified and directed by Engineer-in-charge.

Supply and fixing Batten holder 2 Amp 250V AC with skrit ISI marked top line series , polycarbonate cased body of brass with back plate suitable for batten fittings complete including 9W LED bulb, complete all as specified and directed by Engineer-in-charge.

Supply and fixing Electric / Electronic Bell, ding dong type 230 Volt AC supply, complete all as specified and directed by Engineer-in-charge.

Supply and fixing wall mounted Retro LED 20 watt, Batten decorative type, appx 4 feet long, pre wired including LED tube light 20W, 6000K with inbuilt driver complete fitting and all other accessories fitting arrangements including electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector including taking down old unserviceable light fittings any type, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing LED mirror light fiting 7/ 9 watt, 6000K, lineer & compact with decorative grey end caps, polycarbonate body and ribbrd opal diffuser complete fitting with lamp and all other accessories fitting arrangements including electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector including taking down old unserviceable light fittings any type, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing LED bulb/lamp 9/10W (100 lumens per watt) (suitable for B22 base), 6000K, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing recessed LED ceiling light with wide light window for maximized glare free output suitable for 600mm x 600mm and ceiling cutout 595mm x 595mm modular grid/POP ceiling complete fitting with separate electronic driver and high brightness SMD LEDs 36 watt, 6000K and one nos extra LED driver along the fittings including connecting electric connection, including taking down unserviceable old fitting any type, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Sleek Pressure die cast aluminium housing, heat resistant glass, energy saving, IP65 protection, better optics for uniform distribution street/Roadway luminaire with high power LED 25 watt complete fitting with driver, LED strip and all other accessories etc, suitable for direct mounting on pipe bracket, fixing on wall with and including brackets made out of GI tubing lightwith suitable bent to shape at 120 degree angle at half metre from bottom (as per sample), fixing with MS clamp (02 Nos) and nut bolts, including before fixing applying two coats of aluminium paint on bracket and clamp over a coat of red oxide primer, including making electric connection with using twin core copper cable of suitable size including taking down old unserviceable light fittings any type, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement switch piano flush type, 5/6Amps, 250 volts, single pole, one way fixed on existing sheet, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement Socket outlet multipurpose. 2 in 1, 5 pin 5/6 Amp, 250 volts flush type fixed on existing sheet, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement switch piano flush type, 15/16Amps, 250 volts, single pole, one way fixed on existing sheet, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement Socket outlet multipurpose. 2 in 1, 5 pin 15/16 Amp, 250 volts flush type fixed on existing sheet, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement Batton holder 2 Amp 250 V AC skrit ISI marked top line series, polycarbonate cased body of brass with back plate suitable for batten fittings, complete all as specified and as directed by Engineer-in-charge.

Material and labour for Sub main wiring complete with two single core 4 sqmm,1100 volts grade, PVC insulated, multi stranded copper conductor cable FRLSH with continuous copper earth conductor of 4 sqmm in existing PVC concealed conduit including taking down old unserviceable submain wiring, complete all as specified and directed by Engineer-in-charge.

Material and labour for Sub main wiring complete with two single core 6 sqmm,1100 volts grade, PVC insulated, multi-stranded copper conductor cable FRLSH with continuous copper earth conductor of 6 sqmm in existing PVC concealed conduit including taking down old unserviceable submain wiring, complete all as specified and directed by Engineer-in-charge.

Material and labour for Sub main wiring complete with two single core 4 sqmm,1100 volts grade, PVC insulated, multi stranded copper conductor cable FRLSH with continuous copper earth conductor of 4 sqmm in & including PVC conduit size 20mm including taking down old unserviceable submain wiring, complete all as specified and directed by Engineer-in-charge.

Material and labour for submain wiring complete with two single core 6 sqmm 1100 volts grade, PVC insulated multi stranded copper conductor cable FRLSH with continuous copper earth conductor of 6 Sqmm in & including PVC conduit size 20 mm including taking down old unserviceable submain wiring, complete all as specified and directed by Engineer-in-charge.

Supply and fixing in replacement (concealed in wall or as directed) factory made DB (made out of CRCA sheet) SPN, 8 Way 240V, double door, earth bar, copper bus bar 200 Amp and neutral link, protection class IP-43 suitable for mounting MCB/Isolator, conforming to IS-8623, BS-5484 dust and vermin proof, including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty, complete all as specified and directed by Engineer-in-charge.

Supply and fixing in replacement (concealed in wall or as directed) factory made DB (made out of CRCA sheet) TPN, 4 Way 415 V (8+12 modules), double door, earth bar, copper bus bar 200 Amp and neutral link, protection class IP-43 suitable for mounting MCB/Isolator, conforming to IS-8623, BS-5484 dust and vermin proof, including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty, complete all as specified and directed by Engineer-in-charge.

Supplying and fixing MCB SP suitable for 230 volts AC supply 5 to 32 Amps, SP rupturing capacity not less than 10KA, C Curve ISI Marked, 1 Module including taking down old unserviceable MCB SP, complete all as specified and directed by Engineer-in-charge.

Supplying and fixing MCB SPN 16 to 40 Amps, 10 KA 'C' curve 230 V AC, 50 Hz including necessary attachment including taking down old unserviceable MCB SPN, complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing MCB TPN 63 Amps 415 Volt AC, C curve, 4 module capacity not less than 10 KA including taking down old unserviceable MCB TPN, complete all as specified and directed by Engineer-in-charge.

Supply and fixing (Concealed with wall) single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amps, 240 volts, AC supply including taking down old unserviceable enclosure, complete all as specified and directed by Engineer-in-Charge.

Material and labour for Retro LED 20 watt tube only appx 4 ' long 6000k min 100 lumens per watt with inbuilt driver to be fixed in to existing batten in replacement of tube 34/40 watt including taking down of existing tube rod, complete all as specified and directed by Engineer-in-charge.

Supply and fixing decorative ultra slim liner LED lighting fixture with extended poly carbonate environmental friendly, energy efficient suitable for 16W to 20W with LED tube of model E-LITE LED pride and connecting up, complete all as specified and directed.

K L JINDAL AND CO.

M/S BHAGWATI CONSTRUCTION COMPANY

M/s DHEERAJ JAIN CONSTRUCTION COMPANY

SHARDA ENTERPRIES

RAKESH KUMAR GARG & CO.

R K GOYAL & COMPANY

G N CONSTRUCTIONS

M/s GURFATEH BUILDERS

M/S VIAJY BUILDERS & DEVELOPERS

Aman Enterprises