PERIODICAL SERVICES TO OTM, MD ACCN AND DAY TO DAY PETTY REPAIRS TO MISC B AND R ITEMS IN VARIOUS BLDGS AND REPAIRS TO ROOF, JOINERY, LEAKAGE / SEEPAGE AND CERTAIN MISC B/R WORKS AT BCF AND NSD SEWRI UNDER GE (NW) MANKHURD

Amount

Petty work as in repairs for plumbing/internal water supply works such as repair to leaking bib taps, pillar taps, CP mixers, stop cocks, waste pipe for WHB, Urinal and sink by tightening and providing spindle, washer repairs to float valves, low levelled cistern, PVC connection, hot or cold pipe line, flushing cistern, coupling to waste pipe to the satisfaction of user as assigned by the engineer in charge

Petty works as in repairs for wooden joinery/PVC doors/aluminium windows, WPC doors works such as Resecuring or easing and adjusting of doors, windows kitchen cabinets in any size, refixing hinges etc by providing glue nails and screws to the satisfaction of user and rectifying other misc minor carpentary works assigned by the Engineer In charge. (Note : Replacement of builders hardware if required shall be measured and paid separately under relevant item) Note for item No 1, 2 and 3 : (a) Rep of contractor will collect details of complint from departmant. The contractor will be alloted complaint on daily basis and sufficient resources will be deployed by him/her for completion of day to day comaplaint within 24 Hrs from the time of reporting. Any delay beyond above mentioned time limit suitable penalties as mentioned in relavant clause of Contract. (b) A detailed log of complaints with completion/ non-completion remarks from users/MES will be maintained by the contractor and same will be updated on daily basis in consulatation with Engr-in-Charge or JE detailed by him. (c) The contractor will make suitable arrangment for emergent complaints and will notify auth rep/Engr-in-Charge about extraordinary circumstances for probable non-completion or delay in rectification of complaints beyond state time limit set for disposal of complaint. In case of any dispute the decision of accepting officer will be final and binding in this regard. (d) The quoted rated deems to be inclusive of transportation and other expenses required for the resource deployment at the complaint site around scattered Naval Depo. (e) The contractor will maintain suitable inventories and range of spares required to meet the complaints as same will be reviewed peridically by Engr-in-charge to streamline complaints disposal system. (f) Requisite skilled manpower more than two will be provided by the contractor based on site requirements in one day. No extra payment will be provided on this account.

Taking down cement plaster of any description from brick or stone walls including raking out joints, hacking for key , scrubbing down with water etc and removing debris outside MD land upto requisite lead complete all as specified and M&L for rendering 15mm thick in two coats (10+5mm) polymer modified ready mix cement based plaster on the wall surfaces including finishing the surface of top layer even and smooth complete all as specified and directed make: easyplast from wall plast/readiplast from ultratech including material and labour for preparation of new plastered surfaces on walls, preparation for Acrylic emulsion and applying applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal rsistance, dirt resistance exterior paint of required shades(Company Depot Tinted) with silicon additives @ 1.43 litre/10sqm over & including priming coat of extreior primer applied @ 0.90 litre/10 sqm over new surfaces complete all as specified

Taking down cement plaster of any description from brick or stone walls including raking out joints, hacking for key , scrubbing down with water etc and removing debris outside MD land upto requisite lead complete all as specified and M&L for rendering 10mm thick polymer modified ready mix cement based plaster on the wall surfaces including finishing the surface of top layer even and smooth complete all as specified and directed make: easyplast from wall plast/readiplast from ultratech including material and labour for preparation of new plastered surfaces on walls, preparation for distempering and applying two coat of oilbound distemper over a coat of primer including stopping of nails holes,cracks etc and 1 mm thick (minimum) white cement based wall care putty on old surfaces of walls etc, finished even and smooth, complete all as specified and directed.

Taking down cement plaster of any description from brick or stone walls including raking out joints, hacking for key , scrubbing down with water etc and removing debris outside MD land upto requisite lead complete all as specified and M&L for rendering 5mm thick polymer modified ready mix cement based plaster on the wall surfaces including finishing the surface of top layer even and smooth complete all as specified and directed make: easyplast from wall plast/readiplast from ultratech including material and labour for preparation of new plastered surfaces and applying three coats of white wash complete all as specified and directed.

M&L for structural repairs to columns, beams, slabs and chajjas at maximum height of 16 mts including scaffolding and safety measurements completely all as specified and directed by Engineer-in-charge in following steps as mentioned below 1) Chipping , Removing,Carefullly Loose Concrete work by low impact Hammer/Breakar without damaging the structure & cleaning and disposal of debris/mortar of demolition out side the premises etc. complete as directed. Hard concrete should not be removed by force. 2) M&L for cleaning existing reinforcement with wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hr between the coats, complete all as specified and directed. (Note :- Mode of measurement: superficial area of concrete will be measured.) 3) M&L for Anticorrosive Treatment to Reinforcement using Corroseal - ZR of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces, complete all as specified and directed. 4) M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem as approved by GE over exposed concrete surfaces prior to application of any type of mortar to ensure bond between old concrete & new concrete by brush application, complete all as specified and directed. 5) M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Molith-PMM) OR Polymer mortar HB of Dr Fixit upto 40mm thickness including levelling, profiling etc in two layers, each layer not exceeding 20mm, complete all as specified and directed. 6) M&L for rendering 15mm thick in two coats (10+5mm) polymer modified ready mix cement based plaster on the wall surfaces including finishing the surface of top layer even and smooth complete all as specified and directed make: easyplast from wall plast/readiplast from ultratech including material and labour for preparation of new plastered surfaces on walls, preparation for Acrylic emulsion and applying applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal rsistance, dirt resistance exterior paint of required shades(Company Depot Tinted) with silicon additives @ 1.43 litre/10sqm over & including priming coat of extreior primer applied @ 0.90 litre/10 sqm over new surfaces

M&L for structural repairs to columns, beams, slabs and chajjas at maximum height of 10 mts including scaffolding and safety measurements completely all as specified and directed by Engineer-in-charge in following steps as mentioned below 1) Chipping , Removing,Carefullly Loose Concrete work by low impact Hammer/Breakar without damaging the structure & cleaning and disposal of debris/mortar of demolition out side the premises etc. complete as directed. Hard concrete should not be removed by force. 2) M&L for cleaning existing reinforcement with wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hr between the coats, complete all as specified and directed. (Note :- Mode of measurement: superficial area of concrete will be measured.) 3) M&L for Anticorrosive Treatment to Reinforcement using Corroseal - ZR of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces, complete all as specified and directed. 4) M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem as approved by GE over exposed concrete surfaces prior to application of any type of mortar to ensure bond between old concrete & new concrete by brush application, complete all as specified and directed. 5) M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Molith-PMM) OR Polymer mortar HB of Dr Fixit upto 40mm thickness including levelling, profiling etc in two layers, each layer not exceeding 20mm, complete all as specified and directed. 6) M&L for rendering 10mm thick polymer modified ready mix cement based plaster on the wall surfaces including finishing the surface of top layer even and smooth complete all as specified and directed make: easyplast from wall plast/readiplast from ultratech including material and labour for preparation of new plastered surfaces on walls, preparation for distempering and applying two coat of oilbound distemper over a coat of primer including stopping of nails holes,cracks etc and 1 mm thick (minimum) white cement based wall care putty on old surfaces of walls etc, finished even and smooth, complete all as specified and directed.

M&L for structural repairs to columns, beams, slabs and chajjas at maximum height of 10 mts including scaffolding and safety measurements completely all as specified and directed by Engineer-in-charge in following steps as mentioned below 1) Chipping , Removing,Carefullly Loose Concrete work by low impact Hammer/Breakar without damaging the structure & cleaning and disposal of debris/mortar of demolition out side the premises etc. complete as directed. Hard concrete should not be removed by force. 2) M&L for cleaning existing reinforcement with wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hr between the coats, complete all as specified and directed. (Note :- Mode of measurement: superficial area of concrete will be measured.) 3) M&L for Anticorrosive Treatment to Reinforcement using Corroseal - ZR of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces, complete all as specified and directed. 4) M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem as approved by GE over exposed concrete surfaces prior to application of any type of mortar to ensure bond between old concrete & new concrete by brush application, complete all as specified and directed. 5) M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Molith-PMM) OR Polymer mortar HB of Dr Fixit upto 40mm thickness including levelling, profiling etc in two layers, each layer not exceeding 20mm, complete all as specified and directed. 6) M&L for rendering 5mm thick polymer modified ready mix cement based plaster on the wall surfaces including finishing the surface of top layer even and smooth complete all as specified and directed make: easyplast from wall plast/readiplast from ultratech including material and labour for preparation of new plastered surfaces and applying three coats of white wash complete all as specified and directed.

M&L as in repair for providing CRS TMT bars any dia in various structural RCC elements like columns, beams, Slabs etc. including cutting, bending, fixing of bars with welding/ tying as required at site with & including binding wires etc. and all relevant works like anchoring of the bars in the existing RCC Members, complete all as specified and directed.

M&L for Complete removal of existing treatment and preparation of plastered surfaces on walls, preparation for Acrylic emulsion and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal rsistance, dirt resistance exterior paint of required shades(Company Depot Tinted) with silicon additives @ 1.43 litre/10sqm over & including priming coat of extreior primer applied @ 0.90 litre/10 sqm over new surfaces

M&L for preparation of old plastered surfaces on walls, preparation for Acrylic emulsion and applying one coat of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal rsistance, dirt resistance exterior paint of required shades(Company Depot Tinted) with silicon additives @ 1.43 litre/10sqm over & including priming coat of extreior primer applied @ 0.90 litre/10 sqm over new surfaces

M&L for complete removal of existing treatment by washing, rubbing down and stopping of old decorated surfaces on walls, preparation for wall surface and applying 3mm thick wall care putty on wall and making the wall surface plain by rubbing surface with sand paper to obtain plain surface and applying one coat of alkali resistant priming paint followed by two coat of oilbound distemper complete all as specified and directed by EIC.

M & L for preparation of old distempering surfaces including stopping of nails holes,cracks etc. and applying one coat of oil bound distemper on wall complete all as specified.

M&L for complete removal of existing treatment by washing, rubbing down and stopping of old decorated surfaces on ceiling, preparation for ceiling and applying 3mm thick wall care putty on ceiling and making the surface plain by rubbing surface with sand paper to obtain plain surface and applying three coats of white wash complete all as specified and directed by EIC.

Preparation of old surfaces on ceiling (plastered or unplastered or previously white washed) and applying one coat of white wash complete all as specified.

Preparation of old surfaces on wall (plastered or unplastered or previously white washed) and applying one coat of white wash complete all as specified.

M & L for preparation of old wooden surfaces of any description over 10cm width or girth & applying one coat of synthetic enamel paint complete all as specified.

M & L for preparation of old steel surfaces of any description over 10cm width or girth & applying one coat of aluminium paint complete all as specified.

M&L for Vitrified double charged Coloured Ceramic tiles 9-10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer 15mm thick for laying floor finishes in cement mortar 1:6 to recive tiles/stone slabs including skirting with backing coat including Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and removing debris outside MD land upto requisite lead complete all as specified and directed by EIC.

M&L for Non-skid Coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer 15mm thick for laying floor finishes in cement mortar 1:6 to recive tiles/stone slabs including skirting with backing coat including Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and removing debris outside MD land upto requisite lead complete all as specified and directed by EIC.

M&L for Non-skid Coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer 15mm thick for laying floor finishes in cement mortar 1:6 to recive tiles/stone slabs including Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and removing debris outside MD land upto requisite lead complete all as specified and directed by EIC.

M&L for Non-skid Coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer 15mm thick for laying floor finishes in cement mortar 1:6 to recive tiles/stone slabs including skirting with backing coat including Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and removing debris outside MD land upto requisite lead complete all as specified and directed by EIC.

M&L for Glazed ceramic coloured tiles in vertical surface 450x300x6-7mm thick/ 300x 450x6-7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match (dado) including 10 mm thick back coat of cement plaster on fair faces of brick work 1:3 including Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and removing debris outside MD land upto requisite lead complete all as specified and directed by EIC.

S&F in repair 18mm thick celuka PVC sheet minimum 600 Kg/Cum density grade 1 quality one side pre-laminated and other side plain white colour to make kitchen cabinet/drawer shutters fixed with screws, solvent cement/adhesive and parliament hinge as required as per manufacturer instructions complete as per specifications and as directed by the Engineer-in-Charge. Note:- (i) Cup board accessories ie fittings. handles, hinges, will be measured and paid under this schedule. (ii) Quoted rates deem to be include fixing of cabinet on wall with appropriate rawal plug/ dash through fastener (hammer type). (iii) Fabrication and installation of cabinet to be carried out by authorised vendor of manufacturer only.

S&F as in repairs PVC vent cowl 75/110mm bore with and including rubber ring joints, fixed to walls using clamps upto 15m height including scaffolding and all safety arrangements complete all as specified and directed.

S&F as in repairs 75/110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls using clamps upto 15m height including scaffolding and all safety arrangements including dismantling of old pipe any type/dia all complete all as specified and directed.

S&F in repairs 75/110mm bore PVC (SWR) branch piece single (Single Y/ Double Y ) any type, fixed to walls using clamps upto 15m height including scaffolding and all safety arrangements complete all as specified and directed.

S&F as in repairs 75/110mm bore PVC (SWR) bend any type, fixed to walls using clamps upto 15m height including scaffolding and all safety arrangements complete all as specified and directed.

S&F as in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white with integral foot rests with flush pipe of 32mm dia including 10 ltr capacity low level flushing cistern with necessary PVC connections 15mm size with PTMT nuts of length 450mm long etc complete all as specified and directed by EIC/GE.

S&F as in repairs vitreous China wash basin white, flat back size 550 x 400mm including 15mm dia fancy type pillar tap as approved by the GE, chromium plated CP waste coupling, chain and plug, waste fitting, union and waste pipe 32mm dia of required length and all necessary 450mm long outlet and inlet PVC connections pipes with PTMT check nuts complete all as specified and directed by EIC.

S&F as in repairs vitreous china urinal half stall type (back or corner wall type ), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement with discharge pipe etc complete all as specified and as directed by Engineer In Charge.

S&F as in repairs vitreous coloured China Europeon water closet (Pedestal Pattern) including 10 ltr capacity low level flushing cistern with necessary PVC connections 15mm size with PTMT nuts of length 450mm long etc complete all as specified and directed by EIC.

S&F as in repairs low level/high level PVC flushing cistern with PVC flush pipe, brackets, and PVC connection complete of 10 Ltr capacity all as specified and directed by EIC.

S&F as in repairs 15 mm dia Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as speicified and directed by EIC.

S&F as in repairs Two way Bib cock with flange 15mm dia approved by the GE complete all as specified and directed by EIC.

S&F as in repairs 15mm bore brass CP Stop Cock approved by the GE, complete all as specified and directed by EIC.

S&F as in repairs 15mm bore brass CP angle Stop valve approved by the GE, complete all as specified and directed by EIC.

S&F as in repairs 15mm bore brass CP Bib Tap approved by the GE, complete all as specified and directed by EIC.

S&F as in repairs 15mm bore brass CP Pillar Tap approved by the GE, complete all as specified and directed by EIC.

S&F as in repairs brass chromium plated, shower rose, 125mm size with and including 195mm long 15mm bore brass chromium plated shower arm with bend of 45 degree, complete all as specified and directed by EIC. Make: Seiko, Cera, Jaquar or equivalent approved by GE.

S&F as in repairs Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed 15mm dia of make ESSCO, SEIKO, Cera or equivalent as approved by the GE complete all as specified and directed by EIC.

S&F as in repairs for sinks made of stainless steel 1mm thick kitchen or laboratory with plugs,washers and waste pipe including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting unions to pipe, overall size 495mmx420mm bowl size 410mmx330mmx160mm complete iincluding demolition of old cudappah sink/old sink all as specified and as directed.

S&F in repairs waste fitting of 32 mm bore brass, chromium plated for glazed ware wash basin etc complete all as specified and directed.

S&F in repairs waste fitting of 40 mm bore brass , chromium plated for glazed ware for sink coulpling etc complete all as specified and directed.

S&F in repairs waste pipe for WHB 32mm bore fixed to wash hand basin coupling length pipe 0.90 mtrs each complete all as specified and directed.

S&F in repairs waste pipe for kitchen sink 40mm bore fixed to sinks coupling length pipe 0.90 mtrs each complete all as specified and directed.

S&F in repairs stainless steel grating in round shape 100mm dia with one hole for waste pipe complete all as specified and directed.

S&F in repairs stainless steel grating in ground shape 100mm dia without hole complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 15mm and Supply & fixing 15 mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 20mm and Supply & fixing 20 mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 25mm and Supply & fixing 25 mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 40mm and Supply & fixing 40 mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed.

S&F as in repairs unplasticised PVC pipes of 15mm bore of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe all as specified and directed by GE/EIC.

Supplying and laying as in repairs of 20mm dia CPVC pipes UV stable,leak proof, tough ,rigid , conforming to IS:15778 of SDR 11 standard., medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

S&F as in repairs for 15mm size PVC connection with PTMT nuts 450mm length.complete all as specified and directed by EIC.

S&F as in repair for gun metal globe or gate valves with iron wheel head , screwed both ends for iron pipe & fixed of size 20mm bore complete all as specified and directed by EIC.

S&F as in repair for gun metal globe or gate valves with iron wheel head , screwed both ends for iron pipe & fixed of size 15 mm bore complete all as specified and directed by EIC.

Fixing only sinks made of stainless steel 1mm thick kitchen or laboratory with plugs,washers and waste pipe including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting unions to pipe, overall size 495mmx420mm bowl size 410mmx330mmx160mm complete including demolition/dismantling of old cudappah sink/old sink all as specified and as directed.

S&F as in repairs stainless steel butt hinges, 100mm, medium weight complete all as specified and directed by EIC.

S&F as in repairs stainless steel butt hinges, 75mm, medium weight complete all as specified and directed by EIC.

S&F as in repairs aluminium, anodised, barrel tower bolts of extruded section of size 200mm complete all as specified and directed by EIC.

S&F as in repairs aluminium, anodised, barrel tower bolts of extruded section of size 150mm complete all as specified and directed by EIC.

S&F as in repairs aluminium, anodised, barrel tower bolts of extruded section of size 100mm complete all as specified and directed by EIC.

S&F as in repairs extruded aluminium alloy handles, fabricated type of size 100mm in any position complete all as specified and directed by EIC.

S&F as in repairs extruded aluminium alloy handles, fabricated type of size 150mm in any position complete all as specified and directed by EIC.

S&F as in repairs floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring of length 140mm fixed in floor etc complete all as specified and directed by EIC.

S&F as in repairs for Aluminium wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with in wooden and aluminium windows, doors etc,and fixing of teak wooden beeding, aluminium patti complete all as specified and as directed by the Engineer in charge. Note: i) The rate includes for the removal of shutter from the frame for aluminium windows and refixing the same after fixing of wiremesh along with aluminium patti ii) The rate includes for the removal of wooden beading from the shutter and refixing the same after fixing of wire mesh in wooden door/windows

S&F as in repairs aluminium alloy anodised sliding door bolt with hasp and staple(bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolt of extruded section of size 300 mm fixed at any position all as specified and directed by EIC.

S&F as in repairs 4 levers aluminium Mortice lock size 100 mm complete all as specified and directed by EIC.

S&F as in repairs aluminium (Die cast body) hydraulically Door closer regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg all as specified and directed by EIC.

S&F as in repair fancy type decorated Stainless Steel curtain hanging rods 20 mm dia and fixed to stainless steel bracket for hanging curtain complete all as specified and directed by EIC.

S&F as in repairs Stainless Steel brackets having screw for tightening of curtain rod of 20mm dia for fixing of curtain rod, complete all as specified and directed by EIC.

S&F as in repairs Stainless Steel bright colour decorative corner/end cap for Curtain rod complete all se specified and directed by EIC.

S&F as in repairs stainless steel peg set of six with base plate and fixed wall/door with rawal pugs/ s/s screw all as specified and directed by EIC.

Supply only stainless steel Soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and directed by EIC

S&F as in repairs for brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed by EIC.

S&F as in repairs for brass chromium plated Towel Ring fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and directed by EIC.

M & L for 20 to 25mm machine cut, polished cudappah stone slab, , in window cill, kitchen platform and similar work, laid over and including backing coat, in CM 1:4, 15 mm thick, jointed with grey cement slurry mixed with pigment to match the shade of the slab including dismantling of old stone slabs of any type complete all as specified and as directed by EIC.

Taking down carefully existing aluminium sliding window shutters,(glass/wire mesh) /frame not exceeding 1.5 Square Metre each

All as per Item above but exceeding 1.5 Square Metre and not exceeding 04 Square Metre.

S&F standard aluminum section powder coated in partition / frame and door shutter, sliding windows / ventilators and places otherwise not specified cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass or wire cloth or Bakelite sheet and all necessary fittings, hinges, screws, plugs, locking arrangements for windows, Nylon ball bearing etc completed all as specified and directed (Aluminum section shall be of make Jindal / Hindalco / Indalco). Note :- Weight of Aluminum sections for frames and shutters shall be only considered for payment. Cost of other consumables required for the item shall be deemed to be included in the quoted rate. However glass panes / Bakelite sheet / wire cloth / mortice lock / locking stay / floor spring / floor door stopper only will be measured and paid separately under respective items as supply only. Fixing by element of these items shall be deemed to be included in quoted rate.

Supply only 4 to 5mm thick glass ordinary quality plain with including wooden/rubber beading or gasket for aluminium section complete all as specified

Supply only 2.50 to 3.0mm thick pin head glass with including wooden/rubber beading or gasket for aluminium section complete all as specified

S&F aluminum anodised grill DG- 104 of Deco grill or equivalent fixed with 'F'/'U' section approved make all as specified and directed. Note : (i) Make shall be of M/s Decogrille of M/s Associated Groups or equivalent as approved by the GE. (ii) Minimum thickness of anodizing shall be 15 microns.

Supply only Aluminium wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with in wooden windows, doors etc and including M&L for fixing of teak wooden beading of suitable size all around complete all as specified and as directed by the Engineer-in-Charge.

Supply only new locking arrangement for aluminium windows complete all as specified and directed.

M & L for 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice laminations & other side balancing white lamination, fixed with screws to timber frame work including wooden scantling for borders & taking down of old boards of any type complete all as specified and directed by EIC.

M&L for 12 mm thick Prelaminated particle board, interior grade, both sides with decorative choice laminations fixed with screws to aluminium sections including taking down of old boards of any type complete all as specified and directed by GE/EIC.

Taking down chowkhat or frame (without taking off shutter from the frame) not exceeding 1.5 Square Metre each , removing from the site including cutting holes required for taking out existing hold fast etc. complete all as specified and as directed.

All as per Item above but exceeding 1.5 Square Metre and not exceeding 04 Square Metre each complete all as specified and directed.

Solid PVC Door Frame of size 50mmx 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F for factory made solid PVC panel type PVC door shutter 30mm thick consisting of frame madeout of MS tubes for top and bottom rails MS frame shall be covered with moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent supplying and fixing in the frame at site as per specifications and drawing given under SSR Part II 2020 complete all as specified and directed

S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). all as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account will be provided

S&F for Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

M&L for 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed

S & F,IInd class hardwood 35mm thick Plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed

S & F 2nd class hardwood, glazed and skelton shutter, 35mm thick, open rebated and prepared to receive glass, gauze etc, edges of framing plane, chamfered or rounded, fitted with cut and mitered bead for securing glass, gauze etc, size of member of shutters as specified in SSR Part -I, section 8, class 8.24(a) (Door shutter), supplied and fitted to chowkats complete all as specified and directed

S&F Pre- painted galvalume sheet having aluminum zinc coating with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers. Penetrations and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fastners etc. completely all as specified and directed. upto maximum height of 20 Mtr including scaffolding and all safety equipments if required including Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings as specified. Note : No additional payment on any account will be considered and only plan area whatever have been provided will be measured. Rate quoted maybe considered including of bending for specific curvature as provided in existing building.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet in ridge 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified upto maximum height of 20 Mtr including scaffolding and all safety equipments if required including Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings as specified. Note : No additional payment on any account will be considered and only plan area whatever have been provided will be measured. Rate quoted maybe considered including of bending for specific curvature as provided in existing building.

M&L for cement concrete type E-2,1:5:10 (using 40 mm graded aggregate) as in sunken portion of toilet and bathroom including demolition of old concrete of any description complete all as specified and directed.

M & L for special treatment for sunken portion of WC bath toilet kitchen etc executed in following stages stage 1 providing 15 mm thick plaster in CM 1:3 mixed with water proofing chemical of Dr fixit or shalicrete R of STP ltd in the proportion/quantity all as per manufacturers instructions stage 2 Application of 1 st coat of tarfelt LM of STP Ltd (diluted with water in ratio 1:1) @ 250 gms/sqm and apply the primer on the plastered surfaces Stage 3 Application of 1 st coat of tarfelt LM of STP Ltd (without dilution with water) @ 1kg/sqm by brush all as per manufacturers instructions. Stage 4 Laying fibre glass cloth ( weight not less than 50 gm/sqm) over 1 st coat while the coated surface is still sticky Stage 5 After 6 to 7 hours iterval, apply second coat ie final coat of tarflet LM of STP ltd (without dilution with water) @ 1 kg/sqm by brush as per manufacturers instructions. Stage 6 Providing 10 mm thick protective plaster in CM 1:3 mixed with STP No. 1 @ 250 ml/50Kg cement all as per manufacturer's instructions. Stage 7 Carry out ponding test for 48 hours to ensure water tightness of repaired sunken portion. Notes: (i) Mode of measurement: Actual area treated (floor and adjoining walls) will be measured and paid.

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors, Gates including Hold fast & Aldrop and related items; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 including of dismantling of old iron or mild steel work of any description complete all as specified and as directed by EIC.

M & L as in repairs for providing and injecting ATT chemical emulsion for Post Constructional Anti-termite Treatment At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre per hole by drilling 6mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same all as specified and directed by EIC Note: Anti-termite treatment shall be performed by authorized agencies specified in list of approved make/brand in CA tender.

M&L as in repairs for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed by EIC Note: Anti-termite treatment shall be performed by authorized agencies specified in list of approved make/brand in CA tender.

M&L for pre polished Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over and including backing coat of 10mm thick in CM 1:3. and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, cutting upto mirror finish and polishing complete polishing complete including dismantling/hacking out/roughening of existing old surface

M&L for PU (polyurethane) FOAM INJECTION Grouting work by drilling 3/4’ into the structure and fixing up 4” of metallic packer then connect it with high pressure grouting machine with reaction time between 5-30 sec with velocity of 90 to 150 which covers crack upto 5mm. PU injection is a hydrophobic grout based on polyurethane upon contact with water, it reacts to form a closed cell rubber like foam while expanding its volume up to 27 times. The cured material is of a constant volume. Since water is not a component of the foam structure, the cured materials is essentially not affected by water or dryness. The reached material does not shrink or swell. Depending on the pressure of injection, it reacts to a form a very dense materials or foam. (make Dr. Fixit, STP, Asian paints or equivalent make as specified in BOQ) Note : (i) The application of PU foam injection grouting should be carried out by the applicator through auth company (STP, Dr. Fixit, Asian paints). (ii) The requisite guarantee for the process after completion shall be considered as per manufacturers instructions.

Note : A SUM OF RS 31385.00 TOWARDS SCHEDULE OF CREDIT SHALL BE DEDUCTED TO ARRIVE THE CONTRACT SUM

A G ENTERPRISES (BID ID -3390167)

M/s Shree Construction Co (BID ID -3390008)

M/s Mohd Altaf Hanif Qureshi (BID ID -3389746)

M/s Mukesh Engineers (BID ID -3389695)

Parmatma Enterprises (BID ID -3389575)

mp construction co (BID ID -3389280)

KRISHNA ENGINEERS (BID ID -3389801)

A M ENTERPRISES (BID ID -3389192)

Bidder Name

sahajanand const co.