REPAIR/ REPLACEMENT OF RISING MAIN DISTRIBUTION CLEANING OF UNDERGROUND SUMP OVERHEAD TANKS AND INSTALLATION UNDER GE AF SRINAGAR

Amount

Excavation in trenches n.exc 1.5 M wide and n.exc 1.5 M depth and getting out for laying of cable / pipe etc in any type of soil complete all as specified and directed Engineer-in-Charge.

Returning, filling in, including spreading, leveling watering and well ramming in layers n.exc 25 cm thick in any type of soil complete all as specified and directed by Engineer-in-Charge.

Removing of excavated soil to a distance n.exc 50 mtr and depositing where directed at a level not exceeding 1.5 m above the starting point, complete all as specified and directed Engineer-in-Charge.

Taking up cast iron water mains (including all fittings) by disconnecting, spigot and socket ends and flanged ends including proper taking off complete of the following bore of pipe, complete all as specified and directed by Engineer-in-Charge

150 mm bore

100 mm bore

Supply and lay in trenches ductile iron pipes, socket and Spigot ends, of following size, ISI marked Centrifugally Cast (Spun) Ductile Iron Pressure pipes conforming to IS:8329/2000 classification K-7 rating, suitable for push-on-joint (Rubber gasket-D jointing) with cement mortor lining inside the pipes and outside zinc coating with Bituminous finish coat as per IS:8329 / 2000 including provision of EPDM rubber joints conforming IS: 5382 of 1985 complete all as specified and as directed by Engr-in-charge.

150mm bore

100mm bore

Fixing only cast iron water mains (including all fittings) with Spigot socket ends or flanged ends of the following bore of pipe, complete all as specified and directed by Engineer-in-Charge. Note:- (i) Old pipe retrived vide BOQ item No 4 shall be reused. (ii) Run lead joint will be measured & paid seperatly.

150mm bore

100mm bore

M&L for Run lead joints for spigot & socketed type cast iron Pipes and caulking the joints properly for the following sizes, complete all as specified and directed by Engineer-in-Charge

150mm bore

100mm bore

M&L for repairing old run lead joint by burning & removing old run lead from spigot & socketed Cast iron pipe, in any position, filling the same joint by reusing 50% old run lead and balance new run lead, caulking the joints properly to arrest leakage etc, including necessary earth work, excavation as required, for following sizes of cast iron pipes, complete all as specified and directed by Engineer-in-Charge

150mm bore

100mm bore

M&L for repairing old lead wool joint by removing old lead wool from spigot & socketed Cast iron pipe, in any position, filling the same joint by reusing 50% old lead wool and balance new lead wool, caulking the joints properly to arrest leakage etc, including necessary earth work, excavation as required, for following sizes of cast iron pipes, complete all as specified and directed by Engineer-in-Charge

150mm bore

100mm bore

M&L for repairing old Flanged Joints from flanged type Cast iron pipe, in any position, by replacing rubber gasket sheet 3 mm thick, and bolt nuts for following sizes complete all as specified and directed for following sizes:-

150mm bore

100mm bore

Taking down GI tubing complete with all fittings of following bore complete all as specified and directed by Engineer-in-Charge

50mm bore

40mm bore

25mm bore

20mm bore

S&F GI tubing medium grade laid in trenches complete with all GI fittings of following bore complete all as specified and directed by Engineer-in-Charge.

50mm bore

40mm bore

25mm bore

20mm bore

Re-fixing of old steel water tubing as retrieved from item No 11 here-in-before of following bore and connection in new or old position , complete all as specified and directed by Engineer-in-Charge

50mm bore

40mm bore

25mm bore

20mm bore

S&F GI tubes 20 mm bore 'medimum grade' with all fittings including clamps and fixed complete to walls and ceilings complete all as specified and directed by Engineer-in-Charge.

Taking down cast Iron sluice valve / Butterfly valve of following bore complete all as specified and directed by Engineer-in-Charge

Sluice valve 200mm bore

Sluice valve 150mm bore

Sluice valve 100mm bore

Butterfly valve 150mm bore

Butterfly valve 100mm bore

Supply and fix sluice valve, long body type of pressure rating PN-1.6 with stainless steel spindle, both end flanged, ISI marked complete with cast iron wheel, nut, bolt, washer, rubber packing etc., confirming to IS-14846-2000 complete, for following size..

Sluice valve 200mm bore

Sluice valve 150mm bore

Sluice valve 100mm bore

Supply and Fix cast iron butter fly valve, with both end flanged type, conforming to IS 13095 with nuts bolts and washers of suitable size and necessary rubber gaskets etc complete all as specified and directed by Engr-in-Charge, for following size.

Butterfly valve 150mm bore

Butterfly valve 100mm bore

Cleaning of OHT (Overhead tank) approx 18 m stagging removing sludge / sand / dirt manually by wash out through outlet to a distance not less than 50 m from the OHR, cleaning the OHR from inside with bleached water and washing with sodium hydrochloride liquid drying and applying one coat of lime wash internally, spraying anti bacteria liquid , complete all as specified and writing date of cleaning on outer wall in yellow/black paint in a box 60 cm x 30 cm and directed by Engineer-in- Charge for following :-

25000 gallons at No 1 Airmen Mess

50000 gallons at filteration plant, SNCO Mess, Signal Section, OMQ, SMQ Gurudwara, SMQ patnitop

100000 gallons at ATC golf ground, Near KV OHT

Cleaning of UG raw water sump and removing sludge / sand / dirt manually / by sludge removing pump and apply one coat of lime wash internally including disposing the sludge outside MoD land at LALGAM PUMP HOUSE complete all as specified and writing date of cleaning on outer wall in yellow/black paint in a box 60cmx30cm and directed by Engineer-in- Charge for following :-

2500 Gallon Capacity

20000 Gallon capacity

25000 Gallon capacity

Cleaning of UG clean water sump and removing sludge/ sand/ dirt manually/ by sludge removing pump to a distance not less than 50m from the sump cleaning the sumps with bleached water and washing with sodium hydrochloride liquid, drying and apply one coat of lime wash internally complete all as specified and writing date of cleaning on outer wall in yellow/black paint in a box 60cmx30cm and directed by Engineer-in- Charge for following :-

20000 gallon at SRI-IV Pump house

25000 gallon at SRI-IV & WSA Pump house

50000 gallon at Filteration Plant and Doodhganga

62500 gallon at Dhoodhganga Pump House

125000 gallon at Dhoodhganga Pump House

Taking down the following unserviceable NRV with all accessories etc complete all as specified & directed by Engr-in-Charge.

150 mm bore

100 mm bore

Supply and fix cast iron reflux valve suitable for following bore pipe heavy duty both end flanged of pressure rating PN 1.6 and jointing with joint with rubber or fibre board gasket complete all as specified & directed by Engr-in-Charge

150 mm bore

100 mm bore

Disconnecting and taking down unserviceable Cast iron air release valve with all accessories etc complete.

150 mm bore

100 mm bore

S&F Cast Iron Air release valves with two outlets, conforming to IS 14845 of following dia bore , complete all as specified and directed by Engineer-in- Charge

150 mm bore

100 mm bore

Taking down gun metal gate valve of following sizes, complete all as specified and directed by Engineer-in- Charge

50mm dia

40mm dia

25mm dia

20mm dia

S&F Gun metal gate valve, yoke type, full opening with iron wheel head, screwed both ends , heavy duty, ISI marked complete for iron pipe of following sizes , complete all as specified and directed by Engineer-in- Charge

50mm dia

40mm dia

25mm dia

20mm dia

Supply and fix in repair 500 litres capacity double layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete.

M&L for Cast Iron Specials ISI marked conforming to IS 9523/2000 suitable for spigot socket/ flanged type cast iron pipe such as bend,Tee,tail piece, blend piece of upto 150 mm pressure Rating PN1.0 etc,complete all as specified and directed by Engineer-in- Charge

S&F Ductile Iron fitting / special for DI pipes like bends (any type, radius and angle) increasing, decreasing or double socketed / flanged tee pieces single branch 'Y' junction double branch, cross collars caps and plugs, connecting pieces one end flanged and other end socket or spigot and bell mouth pieces one end flanged other end tapering as bell mouth suitable for up to 150mm bore pipe complete all as specified.

Supply only rubber insertion sheet 3 mm thick for flanged joint complete all as specified and directed by Engineer-in-Charge

M/s Jaipal Associates

M/S M.Y Enterprises

M/S NEW FAROOQ TRADERS