Renovation of Canal regulating Structure At RD 141000 of Bist Doab Canal (Phase 2)

Amount

Supplying, fitting and placing HYSD bar reinforcement in substructure complete as per drawing and Technical Specifications.

Supplying, fitting and placing HYSD bar reinforcement in super-structure complete as per drawing and technical specifications

Structural steel work in angles, tees, flats, riveted, including cutting, fixing all gusset plates, bolts, nuts, rivets etc. with hoisting and erecting in position.

Plain/Reinforced cement concrete in sub-structure complete as per drawing and Technical Specifications RCC Grade M-30 Height upto 5m Using Concrete Mixer

Plain/Reinforced Cement Concrete in Open Foundation complete as per drawing per Drawing and Technical Specifications RCC Grade M30 Using Concrete Mixer

Furnishing and Placing RCC Grade M 30-For solid slab in superstructure Using Concrete Mixer For Solid slab super-structureincluding centering and shuttering Height up to 5m as per drawing and Technical Specification

Dismantling Reinforced cement concrete

Dismantling Cement concrete plain1:2:4 mix

Providing and fixing of Standard Metal Delineatoras per IRC 79:2019 consisting of retro reflectivearea in white color using full cube corner microprismatic non-metallic retro reflective sheeting oneach side conforming with IRC 67 2012 andmeeting the coefficient of retro reflection values as per ASTM D 4956 Type XI table specification. The delineator shall be painted with only black colorpowder coat of minimum 40 microns thickness, on top of which retro reflective sheeting only in white colour shall be pasted on both sides. The structure shall have height not less than 800 mm above the ground, width not less than 100 mmand shall extend not more than 300mm below the ground while being installed. The delineator shall have grooves across the length to make the reflective sheets vandal-proof. The delineator is meant for application on gaps in median, traffic islands, dangerous bends, roundabouts, narrow bridges etc. or as desired by site engineer.

Excavation of Soil using Hyraulic Excavator and hydraulic Tractor Trolly I/C cutting and loading in Trolly and transporting to the embankment locations with all lifts and lead (a) Disposal/carraige from 0 upto 450m,additional beyond450m upto 1Km

Compaction Extra for laying earth/fly ash as per specifications in 20 cm. Layers and dressing including cost of rolling,watering the earth/fly ash laid in 20 cm layers as per specifications for compaction for rolling to specifications

Construction of unreinforced plain cement concrete pavement in M-30 mix design over a prepared sub base with OPC 43 grade conforming to IS:383 mixed with concrete mixer using batch type concrete mixer as per IS:1791,laid in position, compacted with needle vibrator, screed vibrator and plate vibrator, dewatering of free water with vaccum pump, finishing the surface with power floater, finishing to required lines and grades as per drawings and technical clause 1501 of MORD specifications

Providing and filling joint sealing compound with coarse sand and 6 percent bitumen by weight complete as per drawings and technical clause 2605 of MORT&H specifications

Tile terracing laid dry over roof consisitng of one layer of tiles 22.86x11.43x3.83 including grouting with cement sand mortar 1:4 top surface to be left clean after wire brushing

Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.

Cement concrete 1:6:12 with stone aggregate 40mm gauge mixing by mechanical means using concrete mixer volumetric type

Painting two or more coats with synthetic enamel paints in all shades on old wood work or metallic or plastered or concrete surface to give an even shade including rubbing down old paint.

Painting two or more coats with anticorrosive bitumastic Paint to give an even shade

Finishing walls with exterior decorative cement based paint such as snowcem, robbiacem etc. two or more coats to give an even shade

Dismantling brick work tile, masonry or tile lining in cement

HIT-V M12 Anchor bolt with HY 200 Adhesive

M.S Spindle with double start or triple start threading 11' height 1/3/4" dia. complete up to 1.5 ton capacity

Providing L.E.D light of standard reputed company with minimum 2 year warranty 50W

Removing damaged old rubber seal bulb or flat including clamp plate of all sizes & types

Providing of hollow bulb seal &fixing in position including preparation of surface complete in al respects and to entire satisfaction of Engineer in charge

Commissioning & testing of Gates at site complete in all respects and to entire satisfactrion of Engineer in Charge

Proving &fixing in position of Flat/wedge seal includijng preparation of surface complete in all respects and to entire satisfaction ofEngineer in charge.

Overhauling of gate mechanism of all types including dismantling,greasing,oiling and re-installation of mechnism complete in all aspects upto 10 feet width of gate

Scraping brushing to remove paint to basemetal surfac

Any Other Item as per CSR Rate

RAJ KUMAR